mirror of https://gitee.com/openkylin/linux.git
378 lines
10 KiB
Plaintext
378 lines
10 KiB
Plaintext
#
|
|
# Touchscreen driver configuration
|
|
#
|
|
menuconfig INPUT_TOUCHSCREEN
|
|
bool "Touchscreens"
|
|
help
|
|
Say Y here, and a list of supported touchscreens will be displayed.
|
|
This option doesn't affect the kernel.
|
|
|
|
If unsure, say Y.
|
|
|
|
if INPUT_TOUCHSCREEN
|
|
|
|
config TOUCHSCREEN_ADS7846
|
|
tristate "ADS7846/TSC2046 and ADS7843 based touchscreens"
|
|
depends on SPI_MASTER
|
|
depends on HWMON = n || HWMON
|
|
help
|
|
Say Y here if you have a touchscreen interface using the
|
|
ADS7846/TSC2046 or ADS7843 controller, and your board-specific
|
|
setup code includes that in its table of SPI devices.
|
|
|
|
If HWMON is selected, and the driver is told the reference voltage
|
|
on your board, you will also get hwmon interfaces for the voltage
|
|
(and on ads7846/tsc2046, temperature) sensors of this chip.
|
|
|
|
If unsure, say N (but it's safe to say "Y").
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ads7846.
|
|
|
|
config TOUCHSCREEN_BITSY
|
|
tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
|
|
depends on SA1100_BITSY
|
|
select SERIO
|
|
help
|
|
Say Y here if you have the h3600 (Bitsy) touchscreen.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called h3600_ts_input.
|
|
|
|
config TOUCHSCREEN_CORGI
|
|
tristate "SharpSL (Corgi and Spitz series) touchscreen driver"
|
|
depends on PXA_SHARPSL
|
|
default y
|
|
help
|
|
Say Y here to enable the driver for the touchscreen on the
|
|
Sharp SL-C7xx and SL-Cxx00 series of PDAs.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called corgi_ts.
|
|
|
|
config TOUCHSCREEN_FUJITSU
|
|
tristate "Fujitsu serial touchscreen"
|
|
select SERIO
|
|
help
|
|
Say Y here if you have the Fujitsu touchscreen (such as one
|
|
installed in Lifebook P series laptop) connected to your
|
|
system.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called fujitsu-ts.
|
|
|
|
config TOUCHSCREEN_GUNZE
|
|
tristate "Gunze AHL-51S touchscreen"
|
|
select SERIO
|
|
help
|
|
Say Y here if you have the Gunze AHL-51 touchscreen connected to
|
|
your system.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called gunze.
|
|
|
|
config TOUCHSCREEN_ELO
|
|
tristate "Elo serial touchscreens"
|
|
select SERIO
|
|
help
|
|
Say Y here if you have an Elo serial touchscreen connected to
|
|
your system.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called elo.
|
|
|
|
config TOUCHSCREEN_MTOUCH
|
|
tristate "MicroTouch serial touchscreens"
|
|
select SERIO
|
|
help
|
|
Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
|
|
your system.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called mtouch.
|
|
|
|
config TOUCHSCREEN_INEXIO
|
|
tristate "iNexio serial touchscreens"
|
|
select SERIO
|
|
help
|
|
Say Y here if you have an iNexio serial touchscreen connected to
|
|
your system.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called inexio.
|
|
|
|
config TOUCHSCREEN_MK712
|
|
tristate "ICS MicroClock MK712 touchscreen"
|
|
help
|
|
Say Y here if you have the ICS MicroClock MK712 touchscreen
|
|
controller chip in your system.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called mk712.
|
|
|
|
config TOUCHSCREEN_HP600
|
|
tristate "HP Jornada 6xx touchscreen"
|
|
depends on SH_HP6XX && SH_ADC
|
|
help
|
|
Say Y here if you have a HP Jornada 620/660/680/690 and want to
|
|
support the built-in touchscreen.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called hp680_ts_input.
|
|
|
|
config TOUCHSCREEN_HP7XX
|
|
tristate "HP Jornada 7xx touchscreen"
|
|
depends on SA1100_JORNADA720_SSP
|
|
help
|
|
Say Y here if you have a HP Jornada 710/720/728 and want
|
|
to support the built-in touchscreen.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called jornada720_ts.
|
|
|
|
config TOUCHSCREEN_HTCPEN
|
|
tristate "HTC Shift X9500 touchscreen"
|
|
depends on ISA
|
|
help
|
|
Say Y here if you have an HTC Shift UMPC also known as HTC X9500
|
|
Clio / Shangrila and want to support the built-in touchscreen.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called htcpen.
|
|
|
|
config TOUCHSCREEN_PENMOUNT
|
|
tristate "Penmount serial touchscreen"
|
|
select SERIO
|
|
help
|
|
Say Y here if you have a Penmount serial touchscreen connected to
|
|
your system.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called penmount.
|
|
|
|
config TOUCHSCREEN_MIGOR
|
|
tristate "Renesas MIGO-R touchscreen"
|
|
depends on SH_MIGOR && I2C
|
|
help
|
|
Say Y here to enable MIGO-R touchscreen support.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called migor_ts.
|
|
|
|
config TOUCHSCREEN_TOUCHRIGHT
|
|
tristate "Touchright serial touchscreen"
|
|
select SERIO
|
|
help
|
|
Say Y here if you have a Touchright serial touchscreen connected to
|
|
your system.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called touchright.
|
|
|
|
config TOUCHSCREEN_TOUCHWIN
|
|
tristate "Touchwin serial touchscreen"
|
|
select SERIO
|
|
help
|
|
Say Y here if you have a Touchwin serial touchscreen connected to
|
|
your system.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called touchwin.
|
|
|
|
config TOUCHSCREEN_ATMEL_TSADCC
|
|
tristate "Atmel Touchscreen Interface"
|
|
depends on ARCH_AT91SAM9RL
|
|
help
|
|
Say Y here if you have a 4-wire touchscreen connected to the
|
|
ADC Controller on your Atmel SoC (such as the AT91SAM9RL).
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called atmel_tsadcc.
|
|
|
|
config TOUCHSCREEN_UCB1400
|
|
tristate "Philips UCB1400 touchscreen"
|
|
select AC97_BUS
|
|
help
|
|
This enables support for the Philips UCB1400 touchscreen interface.
|
|
The UCB1400 is an AC97 audio codec. The touchscreen interface
|
|
will be initialized only after the ALSA subsystem has been
|
|
brought up and the UCB1400 detected. You therefore have to
|
|
configure ALSA support as well (either built-in or modular,
|
|
independently of whether this driver is itself built-in or
|
|
modular) for this driver to work.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ucb1400_ts.
|
|
|
|
config TOUCHSCREEN_WM97XX
|
|
tristate "Support for WM97xx AC97 touchscreen controllers"
|
|
depends on AC97_BUS
|
|
help
|
|
Say Y here if you have a Wolfson Microelectronics WM97xx
|
|
touchscreen connected to your system. Note that this option
|
|
only enables core driver, you will also need to select
|
|
support for appropriate chip below.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called wm97xx-ts.
|
|
|
|
config TOUCHSCREEN_WM9705
|
|
bool "WM9705 Touchscreen interface support"
|
|
depends on TOUCHSCREEN_WM97XX
|
|
help
|
|
Say Y here if you have a Wolfson Microelectronics WM9705
|
|
touchscreen controller connected to your system.
|
|
|
|
If unsure, say N.
|
|
|
|
config TOUCHSCREEN_WM9712
|
|
bool "WM9712 Touchscreen interface support"
|
|
depends on TOUCHSCREEN_WM97XX
|
|
help
|
|
Say Y here if you have a Wolfson Microelectronics WM9712
|
|
touchscreen controller connected to your system.
|
|
|
|
If unsure, say N.
|
|
|
|
config TOUCHSCREEN_WM9713
|
|
bool "WM9713 Touchscreen interface support"
|
|
depends on TOUCHSCREEN_WM97XX
|
|
help
|
|
Say Y here if you have a Wolfson Microelectronics WM9713 touchscreen
|
|
controller connected to your system.
|
|
|
|
If unsure, say N.
|
|
|
|
config TOUCHSCREEN_WM97XX_MAINSTONE
|
|
tristate "WM97xx Mainstone accelerated touch"
|
|
depends on TOUCHSCREEN_WM97XX && ARCH_PXA
|
|
help
|
|
Say Y here for support for streaming mode with WM97xx touchscreens
|
|
on Mainstone systems.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called mainstone-wm97xx.
|
|
|
|
config TOUCHSCREEN_USB_COMPOSITE
|
|
tristate "USB Touchscreen Driver"
|
|
depends on USB_ARCH_HAS_HCD
|
|
select USB
|
|
help
|
|
USB Touchscreen driver for:
|
|
- eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
|
|
- PanJit TouchSet USB
|
|
- 3M MicroTouch USB (EX II series)
|
|
- ITM
|
|
- some other eTurboTouch
|
|
- Gunze AHL61
|
|
- DMC TSC-10/25
|
|
- IRTOUCHSYSTEMS/UNITOP
|
|
- IdealTEK URTC1000
|
|
- GoTop Super_Q2/GogoPen/PenPower tablets
|
|
|
|
Have a look at <http://linux.chapter7.ch/touchkit/> for
|
|
a usage description and the required user-space stuff.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called usbtouchscreen.
|
|
|
|
config TOUCHSCREEN_USB_EGALAX
|
|
default y
|
|
bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
|
|
depends on TOUCHSCREEN_USB_COMPOSITE
|
|
|
|
config TOUCHSCREEN_USB_PANJIT
|
|
default y
|
|
bool "PanJit device support" if EMBEDDED
|
|
depends on TOUCHSCREEN_USB_COMPOSITE
|
|
|
|
config TOUCHSCREEN_USB_3M
|
|
default y
|
|
bool "3M/Microtouch EX II series device support" if EMBEDDED
|
|
depends on TOUCHSCREEN_USB_COMPOSITE
|
|
|
|
config TOUCHSCREEN_USB_ITM
|
|
default y
|
|
bool "ITM device support" if EMBEDDED
|
|
depends on TOUCHSCREEN_USB_COMPOSITE
|
|
|
|
config TOUCHSCREEN_USB_ETURBO
|
|
default y
|
|
bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED
|
|
depends on TOUCHSCREEN_USB_COMPOSITE
|
|
|
|
config TOUCHSCREEN_USB_GUNZE
|
|
default y
|
|
bool "Gunze AHL61 device support" if EMBEDDED
|
|
depends on TOUCHSCREEN_USB_COMPOSITE
|
|
|
|
config TOUCHSCREEN_USB_DMC_TSC10
|
|
default y
|
|
bool "DMC TSC-10/25 device support" if EMBEDDED
|
|
depends on TOUCHSCREEN_USB_COMPOSITE
|
|
|
|
config TOUCHSCREEN_USB_IRTOUCH
|
|
default y
|
|
bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
|
|
depends on TOUCHSCREEN_USB_COMPOSITE
|
|
|
|
config TOUCHSCREEN_USB_IDEALTEK
|
|
default y
|
|
bool "IdealTEK URTC1000 device support" if EMBEDDED
|
|
depends on TOUCHSCREEN_USB_COMPOSITE
|
|
|
|
config TOUCHSCREEN_USB_GENERAL_TOUCH
|
|
default y
|
|
bool "GeneralTouch Touchscreen device support" if EMBEDDED
|
|
depends on TOUCHSCREEN_USB_COMPOSITE
|
|
|
|
config TOUCHSCREEN_USB_GOTOP
|
|
default y
|
|
bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
|
|
depends on TOUCHSCREEN_USB_COMPOSITE
|
|
|
|
config TOUCHSCREEN_TOUCHIT213
|
|
tristate "Sahara TouchIT-213 touchscreen"
|
|
select SERIO
|
|
help
|
|
Say Y here if you have a Sahara TouchIT-213 Tablet PC.
|
|
|
|
If unsure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called touchit213.
|
|
|
|
endif
|