mirror of https://gitee.com/openkylin/linux.git
101 lines
3.7 KiB
Plaintext
101 lines
3.7 KiB
Plaintext
Embedded Memory Controller
|
|
|
|
Properties:
|
|
- name : Should be emc
|
|
- #address-cells : Should be 1
|
|
- #size-cells : Should be 0
|
|
- compatible : Should contain "nvidia,tegra20-emc".
|
|
- reg : Offset and length of the register set for the device
|
|
- nvidia,use-ram-code : If present, the sub-nodes will be addressed
|
|
and chosen using the ramcode board selector. If omitted, only one
|
|
set of tables can be present and said tables will be used
|
|
irrespective of ram-code configuration.
|
|
|
|
Child device nodes describe the memory settings for different configurations and clock rates.
|
|
|
|
Example:
|
|
|
|
memory-controller@7000f400 {
|
|
#address-cells = < 1 >;
|
|
#size-cells = < 0 >;
|
|
compatible = "nvidia,tegra20-emc";
|
|
reg = <0x7000f4000 0x200>;
|
|
}
|
|
|
|
|
|
Embedded Memory Controller ram-code table
|
|
|
|
If the emc node has the nvidia,use-ram-code property present, then the
|
|
next level of nodes below the emc table are used to specify which settings
|
|
apply for which ram-code settings.
|
|
|
|
If the emc node lacks the nvidia,use-ram-code property, this level is omitted
|
|
and the tables are stored directly under the emc node (see below).
|
|
|
|
Properties:
|
|
|
|
- name : Should be emc-tables
|
|
- nvidia,ram-code : the binary representation of the ram-code board strappings
|
|
for which this node (and children) are valid.
|
|
|
|
|
|
|
|
Embedded Memory Controller configuration table
|
|
|
|
This is a table containing the EMC register settings for the various
|
|
operating speeds of the memory controller. They are always located as
|
|
subnodes of the emc controller node.
|
|
|
|
There are two ways of specifying which tables to use:
|
|
|
|
* The simplest is if there is just one set of tables in the device tree,
|
|
and they will always be used (based on which frequency is used).
|
|
This is the preferred method, especially when firmware can fill in
|
|
this information based on the specific system information and just
|
|
pass it on to the kernel.
|
|
|
|
* The slightly more complex one is when more than one memory configuration
|
|
might exist on the system. The Tegra20 platform handles this during
|
|
early boot by selecting one out of possible 4 memory settings based
|
|
on a 2-pin "ram code" bootstrap setting on the board. The values of
|
|
these strappings can be read through a register in the SoC, and thus
|
|
used to select which tables to use.
|
|
|
|
Properties:
|
|
- name : Should be emc-table
|
|
- compatible : Should contain "nvidia,tegra20-emc-table".
|
|
- reg : either an opaque enumerator to tell different tables apart, or
|
|
the valid frequency for which the table should be used (in kHz).
|
|
- clock-frequency : the clock frequency for the EMC at which this
|
|
table should be used (in kHz).
|
|
- nvidia,emc-registers : a 46 word array of EMC registers to be programmed
|
|
for operation at the 'clock-frequency' setting.
|
|
The order and contents of the registers are:
|
|
RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT,
|
|
WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR,
|
|
PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW,
|
|
TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE,
|
|
ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE,
|
|
ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0,
|
|
CFG_CLKTRIM_1, CFG_CLKTRIM_2
|
|
|
|
emc-table@166000 {
|
|
reg = <166000>;
|
|
compatible = "nvidia,tegra20-emc-table";
|
|
clock-frequency = < 166000 >;
|
|
nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
|
|
0 0 0 0 0 0 0 0 0 0 0 0 0 0
|
|
0 0 0 0 0 0 0 0 0 0 0 0 0 0
|
|
0 0 0 0 >;
|
|
};
|
|
|
|
emc-table@333000 {
|
|
reg = <333000>;
|
|
compatible = "nvidia,tegra20-emc-table";
|
|
clock-frequency = < 333000 >;
|
|
nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
|
|
0 0 0 0 0 0 0 0 0 0 0 0 0 0
|
|
0 0 0 0 0 0 0 0 0 0 0 0 0 0
|
|
0 0 0 0 >;
|
|
};
|