mirror of https://gitee.com/openkylin/linux.git
68 lines
3.0 KiB
Plaintext
68 lines
3.0 KiB
Plaintext
These properties are common to multiple MMC host controllers. Any host
|
|
that requires the respective functionality should implement them using
|
|
these definitions.
|
|
|
|
Interpreted by the OF core:
|
|
- reg: Registers location and length.
|
|
- interrupts: Interrupts used by the MMC controller.
|
|
|
|
Card detection:
|
|
If no property below is supplied, host native card detect is used.
|
|
Only one of the properties in this section should be supplied:
|
|
- broken-cd: There is no card detection available; polling must be used.
|
|
- cd-gpios: Specify GPIOs for card detection, see gpio binding
|
|
- non-removable: non-removable slot (like eMMC); assume always present.
|
|
|
|
Optional properties:
|
|
- bus-width: Number of data lines, can be <1>, <4>, or <8>. The default
|
|
will be <1> if the property is absent.
|
|
- wp-gpios: Specify GPIOs for write protection, see gpio binding
|
|
- cd-inverted: when present, polarity on the CD line is inverted. See the note
|
|
below for the case, when a GPIO is used for the CD line
|
|
- wp-inverted: when present, polarity on the WP line is inverted. See the note
|
|
below for the case, when a GPIO is used for the WP line
|
|
- max-frequency: maximum operating clock frequency
|
|
- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on
|
|
this system, even if the controller claims it is.
|
|
- cap-sd-highspeed: SD high-speed timing is supported
|
|
- cap-mmc-highspeed: MMC high-speed timing is supported
|
|
- cap-power-off-card: powering off the card is safe
|
|
- cap-sdio-irq: enable SDIO IRQ signalling on this interface
|
|
- full-pwr-cycle: full power cycle of the card is supported
|
|
|
|
*NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
|
|
polarity properties, we have to fix the meaning of the "normal" and "inverted"
|
|
line levels. We choose to follow the SDHCI standard, which specifies both those
|
|
lines as "active low." Therefore, using the "cd-inverted" property means, that
|
|
the CD line is active high, i.e. it is high, when a card is inserted. Similar
|
|
logic applies to the "wp-inverted" property.
|
|
|
|
CD and WP lines can be implemented on the hardware in one of two ways: as GPIOs,
|
|
specified in cd-gpios and wp-gpios properties, or as dedicated pins. Polarity of
|
|
dedicated pins can be specified, using *-inverted properties. GPIO polarity can
|
|
also be specified using the OF_GPIO_ACTIVE_LOW flag. This creates an ambiguity
|
|
in the latter case. We choose to use the XOR logic for GPIO CD and WP lines.
|
|
This means, the two properties are "superimposed," for example leaving the
|
|
OF_GPIO_ACTIVE_LOW flag clear and specifying the respective *-inverted
|
|
property results in a double-inversion and actually means the "normal" line
|
|
polarity is in effect.
|
|
|
|
Optional SDIO properties:
|
|
- keep-power-in-suspend: Preserves card power during a suspend/resume cycle
|
|
- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion
|
|
|
|
Example:
|
|
|
|
sdhci@ab000000 {
|
|
compatible = "sdhci";
|
|
reg = <0xab000000 0x200>;
|
|
interrupts = <23>;
|
|
bus-width = <4>;
|
|
cd-gpios = <&gpio 69 0>;
|
|
cd-inverted;
|
|
wp-gpios = <&gpio 70 0>;
|
|
max-frequency = <50000000>;
|
|
keep-power-in-suspend;
|
|
enable-sdio-wakeup;
|
|
}
|