mirror of https://gitee.com/openkylin/linux.git
77 lines
2.3 KiB
Plaintext
77 lines
2.3 KiB
Plaintext
Allwinner A31 DMA Controller
|
|
|
|
This driver follows the generic DMA bindings defined in dma.txt.
|
|
|
|
Required properties:
|
|
|
|
- compatible: Must be one of
|
|
"allwinner,sun6i-a31-dma"
|
|
"allwinner,sun8i-a23-dma"
|
|
"allwinner,sun8i-a83t-dma"
|
|
"allwinner,sun8i-h3-dma"
|
|
"allwinner,sun8i-v3s-dma"
|
|
- reg: Should contain the registers base address and length
|
|
- interrupts: Should contain a reference to the interrupt used by this device
|
|
- clocks: Should contain a reference to the parent AHB clock
|
|
- resets: Should contain a reference to the reset controller asserting
|
|
this device in reset
|
|
- #dma-cells : Should be 1, a single cell holding a line request number
|
|
|
|
Example:
|
|
dma: dma-controller@1c02000 {
|
|
compatible = "allwinner,sun6i-a31-dma";
|
|
reg = <0x01c02000 0x1000>;
|
|
interrupts = <0 50 4>;
|
|
clocks = <&ahb1_gates 6>;
|
|
resets = <&ahb1_rst 6>;
|
|
#dma-cells = <1>;
|
|
};
|
|
|
|
------------------------------------------------------------------------------
|
|
For A64 DMA controller:
|
|
|
|
Required properties:
|
|
- compatible: "allwinner,sun50i-a64-dma"
|
|
- dma-channels: Number of DMA channels supported by the controller.
|
|
Refer to Documentation/devicetree/bindings/dma/dma.txt
|
|
- all properties above, i.e. reg, interrupts, clocks, resets and #dma-cells
|
|
|
|
Optional properties:
|
|
- dma-requests: Number of DMA request signals supported by the controller.
|
|
Refer to Documentation/devicetree/bindings/dma/dma.txt
|
|
|
|
Example:
|
|
dma: dma-controller@1c02000 {
|
|
compatible = "allwinner,sun50i-a64-dma";
|
|
reg = <0x01c02000 0x1000>;
|
|
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&ccu CLK_BUS_DMA>;
|
|
dma-channels = <8>;
|
|
dma-requests = <27>;
|
|
resets = <&ccu RST_BUS_DMA>;
|
|
#dma-cells = <1>;
|
|
};
|
|
------------------------------------------------------------------------------
|
|
|
|
Clients:
|
|
|
|
DMA clients connected to the A31 DMA controller must use the format
|
|
described in the dma.txt file, using a two-cell specifier for each
|
|
channel: a phandle plus one integer cells.
|
|
The two cells in order are:
|
|
|
|
1. A phandle pointing to the DMA controller.
|
|
2. The port ID as specified in the datasheet
|
|
|
|
Example:
|
|
spi2: spi@1c6a000 {
|
|
compatible = "allwinner,sun6i-a31-spi";
|
|
reg = <0x01c6a000 0x1000>;
|
|
interrupts = <0 67 4>;
|
|
clocks = <&ahb1_gates 22>, <&spi2_clk>;
|
|
clock-names = "ahb", "mod";
|
|
dmas = <&dma 25>, <&dma 25>;
|
|
dma-names = "rx", "tx";
|
|
resets = <&ahb1_rst 22>;
|
|
};
|