linux/drivers/scsi/t128.c

448 lines
12 KiB
C

#define AUTOSENSE
#define PSEUDO_DMA
/*
* Trantor T128/T128F/T228 driver
* Note : architecturally, the T100 and T130 are different and won't
* work
*
* Copyright 1993, Drew Eckhardt
* Visionary Computing
* (Unix and Linux consulting and custom programming)
* drew@colorado.edu
* +1 (303) 440-4894
*
* DISTRIBUTION RELEASE 3.
*
* For more information, please consult
*
* Trantor Systems, Ltd.
* T128/T128F/T228 SCSI Host Adapter
* Hardware Specifications
*
* Trantor Systems, Ltd.
* 5415 Randall Place
* Fremont, CA 94538
* 1+ (415) 770-1400, FAX 1+ (415) 770-9910
*
* and
*
* NCR 5380 Family
* SCSI Protocol Controller
* Databook
*
* NCR Microelectronics
* 1635 Aeroplaza Drive
* Colorado Springs, CO 80916
* 1+ (719) 578-3400
* 1+ (800) 334-5454
*/
/*
* Options :
* AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
* for commands that return with a CHECK CONDITION status.
*
* PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance
* increase compared to polled I/O.
*
* PARITY - enable parity checking. Not supported.
*
* SCSI2 - enable support for SCSI-II tagged queueing. Untested.
*
*
* UNSAFE - leave interrupts enabled during pseudo-DMA transfers. You
* only really want to use this if you're having a problem with
* dropped characters during high speed communications, and even
* then, you're going to be better off twiddling with transfersize.
*
* USLEEP - enable support for devices that don't disconnect. Untested.
*
* The card is detected and initialized in one of several ways :
* 1. Autoprobe (default) - since the board is memory mapped,
* a BIOS signature is scanned for to locate the registers.
* An interrupt is triggered to autoprobe for the interrupt
* line.
*
* 2. With command line overrides - t128=address,irq may be
* used on the LILO command line to override the defaults.
*
* 3. With the T128_OVERRIDE compile time define. This is
* specified as an array of address, irq tuples. Ie, for
* one board at the default 0xcc000 address, IRQ5, I could say
* -DT128_OVERRIDE={{0xcc000, 5}}
*
* Note that if the override methods are used, place holders must
* be specified for other boards in the system.
*
* T128/T128F jumper/dipswitch settings (note : on my sample, the switches
* were epoxy'd shut, meaning I couldn't change the 0xcc000 base address) :
*
* T128 Sw7 Sw8 Sw6 = 0ws Sw5 = boot
* T128F Sw6 Sw7 Sw5 = 0ws Sw4 = boot Sw8 = floppy disable
* cc000 off off
* c8000 off on
* dc000 on off
* d8000 on on
*
*
* Interrupts
* There is a 12 pin jumper block, jp1, numbered as follows :
* T128 (JP1) T128F (J5)
* 2 4 6 8 10 12 11 9 7 5 3 1
* 1 3 5 7 9 11 12 10 8 6 4 2
*
* 3 2-4
* 5 1-3
* 7 3-5
* T128F only
* 10 8-10
* 12 7-9
* 14 10-12
* 15 9-11
*/
/*
* $Log: t128.c,v $
*/
#include <linux/signal.h>
#include <linux/io.h>
#include <linux/blkdev.h>
#include <linux/interrupt.h>
#include <linux/stat.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/delay.h>
#include "scsi.h"
#include <scsi/scsi_host.h>
#include "t128.h"
#define AUTOPROBE_IRQ
#include "NCR5380.h"
static struct override {
unsigned long address;
int irq;
} overrides
#ifdef T128_OVERRIDE
[] __initdata = T128_OVERRIDE;
#else
[4] __initdata = {{0, IRQ_AUTO}, {0, IRQ_AUTO},
{0 ,IRQ_AUTO}, {0, IRQ_AUTO}};
#endif
#define NO_OVERRIDES ARRAY_SIZE(overrides)
static struct base {
unsigned int address;
int noauto;
} bases[] __initdata = {
{ 0xcc000, 0}, { 0xc8000, 0}, { 0xdc000, 0}, { 0xd8000, 0}
};
#define NO_BASES ARRAY_SIZE(bases)
static struct signature {
const char *string;
int offset;
} signatures[] __initdata = {
{"TSROM: SCSI BIOS, Version 1.12", 0x36},
};
#define NO_SIGNATURES ARRAY_SIZE(signatures)
/*
* Function : t128_setup(char *str, int *ints)
*
* Purpose : LILO command line initialization of the overrides array,
*
* Inputs : str - unused, ints - array of integer parameters with ints[0]
* equal to the number of ints.
*
*/
void __init t128_setup(char *str, int *ints){
static int commandline_current = 0;
int i;
if (ints[0] != 2)
printk("t128_setup : usage t128=address,irq\n");
else
if (commandline_current < NO_OVERRIDES) {
overrides[commandline_current].address = ints[1];
overrides[commandline_current].irq = ints[2];
for (i = 0; i < NO_BASES; ++i)
if (bases[i].address == ints[1]) {
bases[i].noauto = 1;
break;
}
++commandline_current;
}
}
/*
* Function : int t128_detect(struct scsi_host_template * tpnt)
*
* Purpose : detects and initializes T128,T128F, or T228 controllers
* that were autoprobed, overridden on the LILO command line,
* or specified at compile time.
*
* Inputs : tpnt - template for this SCSI adapter.
*
* Returns : 1 if a host adapter was found, 0 if not.
*
*/
int __init t128_detect(struct scsi_host_template * tpnt){
static int current_override = 0, current_base = 0;
struct Scsi_Host *instance;
unsigned long base;
void __iomem *p;
int sig, count;
tpnt->proc_name = "t128";
tpnt->show_info = t128_show_info;
tpnt->write_info = t128_write_info;
for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
base = 0;
p = NULL;
if (overrides[current_override].address) {
base = overrides[current_override].address;
p = ioremap(bases[current_base].address, 0x2000);
if (!p)
base = 0;
} else
for (; !base && (current_base < NO_BASES); ++current_base) {
#if (TDEBUG & TDEBUG_INIT)
printk("scsi-t128 : probing address %08x\n", bases[current_base].address);
#endif
if (bases[current_base].noauto)
continue;
p = ioremap(bases[current_base].address, 0x2000);
if (!p)
continue;
for (sig = 0; sig < NO_SIGNATURES; ++sig)
if (check_signature(p + signatures[sig].offset,
signatures[sig].string,
strlen(signatures[sig].string))) {
base = bases[current_base].address;
#if (TDEBUG & TDEBUG_INIT)
printk("scsi-t128 : detected board.\n");
#endif
goto found;
}
iounmap(p);
}
#if defined(TDEBUG) && (TDEBUG & TDEBUG_INIT)
printk("scsi-t128 : base = %08x\n", (unsigned int) base);
#endif
if (!base)
break;
found:
instance = scsi_register (tpnt, sizeof(struct NCR5380_hostdata));
if(instance == NULL)
break;
instance->base = base;
((struct NCR5380_hostdata *)instance->hostdata)->base = p;
NCR5380_init(instance, 0);
if (overrides[current_override].irq != IRQ_AUTO)
instance->irq = overrides[current_override].irq;
else
instance->irq = NCR5380_probe_irq(instance, T128_IRQS);
if (instance->irq != SCSI_IRQ_NONE)
if (request_irq(instance->irq, t128_intr, 0, "t128",
instance)) {
printk("scsi%d : IRQ%d not free, interrupts disabled\n",
instance->host_no, instance->irq);
instance->irq = SCSI_IRQ_NONE;
}
if (instance->irq == SCSI_IRQ_NONE) {
printk("scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
printk("scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
}
#if defined(TDEBUG) && (TDEBUG & TDEBUG_INIT)
printk("scsi%d : irq = %d\n", instance->host_no, instance->irq);
#endif
printk("scsi%d : at 0x%08lx", instance->host_no, instance->base);
if (instance->irq == SCSI_IRQ_NONE)
printk (" interrupts disabled");
else
printk (" irq %d", instance->irq);
printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d",
CAN_QUEUE, CMD_PER_LUN, T128_PUBLIC_RELEASE);
NCR5380_print_options(instance);
printk("\n");
++current_override;
++count;
}
return count;
}
static int t128_release(struct Scsi_Host *shost)
{
NCR5380_local_declare();
NCR5380_setup(shost);
if (shost->irq)
free_irq(shost->irq, shost);
NCR5380_exit(shost);
if (shost->io_port && shost->n_io_port)
release_region(shost->io_port, shost->n_io_port);
scsi_unregister(shost);
iounmap(base);
return 0;
}
/*
* Function : int t128_biosparam(Disk * disk, struct block_device *dev, int *ip)
*
* Purpose : Generates a BIOS / DOS compatible H-C-S mapping for
* the specified device / size.
*
* Inputs : size = size of device in sectors (512 bytes), dev = block device
* major / minor, ip[] = {heads, sectors, cylinders}
*
* Returns : always 0 (success), initializes ip
*
*/
/*
* XXX Most SCSI boards use this mapping, I could be incorrect. Some one
* using hard disks on a trantor should verify that this mapping corresponds
* to that used by the BIOS / ASPI driver by running the linux fdisk program
* and matching the H_C_S coordinates to what DOS uses.
*/
int t128_biosparam(struct scsi_device *sdev, struct block_device *bdev,
sector_t capacity, int * ip)
{
ip[0] = 64;
ip[1] = 32;
ip[2] = capacity >> 11;
return 0;
}
/*
* Function : int NCR5380_pread (struct Scsi_Host *instance,
* unsigned char *dst, int len)
*
* Purpose : Fast 5380 pseudo-dma read function, transfers len bytes to
* dst
*
* Inputs : dst = destination, len = length in bytes
*
* Returns : 0 on success, non zero on a failure such as a watchdog
* timeout.
*/
static inline int NCR5380_pread (struct Scsi_Host *instance, unsigned char *dst,
int len) {
NCR5380_local_declare();
void __iomem *reg;
unsigned char *d = dst;
register int i = len;
NCR5380_setup(instance);
reg = base + T_DATA_REG_OFFSET;
#if 0
for (; i; --i) {
while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
#else
while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
for (; i; --i) {
#endif
*d++ = readb(reg);
}
if (readb(base + T_STATUS_REG_OFFSET) & T_ST_TIM) {
unsigned char tmp;
void __iomem *foo = base + T_CONTROL_REG_OFFSET;
tmp = readb(foo);
writeb(tmp | T_CR_CT, foo);
writeb(tmp, foo);
printk("scsi%d : watchdog timer fired in NCR5380_pread()\n",
instance->host_no);
return -1;
} else
return 0;
}
/*
* Function : int NCR5380_pwrite (struct Scsi_Host *instance,
* unsigned char *src, int len)
*
* Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
* src
*
* Inputs : src = source, len = length in bytes
*
* Returns : 0 on success, non zero on a failure such as a watchdog
* timeout.
*/
static inline int NCR5380_pwrite (struct Scsi_Host *instance, unsigned char *src,
int len) {
NCR5380_local_declare();
void __iomem *reg;
unsigned char *s = src;
register int i = len;
NCR5380_setup(instance);
reg = base + T_DATA_REG_OFFSET;
#if 0
for (; i; --i) {
while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
#else
while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
for (; i; --i) {
#endif
writeb(*s++, reg);
}
if (readb(base + T_STATUS_REG_OFFSET) & T_ST_TIM) {
unsigned char tmp;
void __iomem *foo = base + T_CONTROL_REG_OFFSET;
tmp = readb(foo);
writeb(tmp | T_CR_CT, foo);
writeb(tmp, foo);
printk("scsi%d : watchdog timer fired in NCR5380_pwrite()\n",
instance->host_no);
return -1;
} else
return 0;
}
MODULE_LICENSE("GPL");
#include "NCR5380.c"
static struct scsi_host_template driver_template = {
.name = "Trantor T128/T128F/T228",
.detect = t128_detect,
.release = t128_release,
.queuecommand = t128_queue_command,
.eh_abort_handler = t128_abort,
.eh_bus_reset_handler = t128_bus_reset,
.bios_param = t128_biosparam,
.can_queue = CAN_QUEUE,
.this_id = 7,
.sg_tablesize = SG_ALL,
.cmd_per_lun = CMD_PER_LUN,
.use_clustering = DISABLE_CLUSTERING,
};
#include "scsi_module.c"