mirror of https://gitee.com/openkylin/linux.git
275 lines
7.1 KiB
ReStructuredText
275 lines
7.1 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0+
|
|
|
|
========================================================
|
|
Linux Driver for the Pensando(R) Ethernet adapter family
|
|
========================================================
|
|
|
|
Pensando Linux Ethernet driver.
|
|
Copyright(c) 2019 Pensando Systems, Inc
|
|
|
|
Contents
|
|
========
|
|
|
|
- Identifying the Adapter
|
|
- Enabling the driver
|
|
- Configuring the driver
|
|
- Statistics
|
|
- Support
|
|
|
|
Identifying the Adapter
|
|
=======================
|
|
|
|
To find if one or more Pensando PCI Ethernet devices are installed on the
|
|
host, check for the PCI devices::
|
|
|
|
$ lspci -d 1dd8:
|
|
b5:00.0 Ethernet controller: Device 1dd8:1002
|
|
b6:00.0 Ethernet controller: Device 1dd8:1002
|
|
|
|
If such devices are listed as above, then the ionic.ko driver should find
|
|
and configure them for use. There should be log entries in the kernel
|
|
messages such as these::
|
|
|
|
$ dmesg | grep ionic
|
|
ionic 0000:b5:00.0: 126.016 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x16 link)
|
|
ionic 0000:b5:00.0 enp181s0: renamed from eth0
|
|
ionic 0000:b5:00.0 enp181s0: Link up - 100 Gbps
|
|
ionic 0000:b6:00.0: 126.016 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x16 link)
|
|
ionic 0000:b6:00.0 enp182s0: renamed from eth0
|
|
ionic 0000:b6:00.0 enp182s0: Link up - 100 Gbps
|
|
|
|
Driver and firmware version information can be gathered with either of
|
|
ethtool or devlink tools::
|
|
|
|
$ ethtool -i enp181s0
|
|
driver: ionic
|
|
version: 5.7.0
|
|
firmware-version: 1.8.0-28
|
|
...
|
|
|
|
$ devlink dev info pci/0000:b5:00.0
|
|
pci/0000:b5:00.0:
|
|
driver ionic
|
|
serial_number FLM18420073
|
|
versions:
|
|
fixed:
|
|
asic.id 0x0
|
|
asic.rev 0x0
|
|
running:
|
|
fw 1.8.0-28
|
|
|
|
See Documentation/networking/devlink/ionic.rst for more information
|
|
on the devlink dev info data.
|
|
|
|
Enabling the driver
|
|
===================
|
|
|
|
The driver is enabled via the standard kernel configuration system,
|
|
using the make command::
|
|
|
|
make oldconfig/menuconfig/etc.
|
|
|
|
The driver is located in the menu structure at:
|
|
|
|
-> Device Drivers
|
|
-> Network device support (NETDEVICES [=y])
|
|
-> Ethernet driver support
|
|
-> Pensando devices
|
|
-> Pensando Ethernet IONIC Support
|
|
|
|
Configuring the Driver
|
|
======================
|
|
|
|
MTU
|
|
---
|
|
|
|
Jumbo frame support is available with a maximim size of 9194 bytes.
|
|
|
|
Interrupt coalescing
|
|
--------------------
|
|
|
|
Interrupt coalescing can be configured by changing the rx-usecs value with
|
|
the "ethtool -C" command. The rx-usecs range is 0-190. The tx-usecs value
|
|
reflects the rx-usecs value as they are tied together on the same interrupt.
|
|
|
|
SR-IOV
|
|
------
|
|
|
|
Minimal SR-IOV support is currently offered and can be enabled by setting
|
|
the sysfs 'sriov_numvfs' value, if supported by your particular firmware
|
|
configuration.
|
|
|
|
Statistics
|
|
==========
|
|
|
|
Basic hardware stats
|
|
--------------------
|
|
|
|
The commands ``netstat -i``, ``ip -s link show``, and ``ifconfig`` show
|
|
a limited set of statistics taken directly from firmware. For example::
|
|
|
|
$ ip -s link show enp181s0
|
|
7: enp181s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
|
|
link/ether 00:ae:cd:00:07:68 brd ff:ff:ff:ff:ff:ff
|
|
RX: bytes packets errors dropped overrun mcast
|
|
414 5 0 0 0 0
|
|
TX: bytes packets errors dropped carrier collsns
|
|
1384 18 0 0 0 0
|
|
|
|
ethtool -S
|
|
----------
|
|
|
|
The statistics shown from the ``ethtool -S`` command includes a combination of
|
|
driver counters and firmware counters, including port and queue specific values.
|
|
The driver values are counters computed by the driver, and the firmware values
|
|
are gathered by the firmware from the port hardware and passed through the
|
|
driver with no further interpretation.
|
|
|
|
Driver port specific::
|
|
|
|
tx_packets: 12
|
|
tx_bytes: 964
|
|
rx_packets: 5
|
|
rx_bytes: 414
|
|
tx_tso: 0
|
|
tx_tso_bytes: 0
|
|
tx_csum_none: 12
|
|
tx_csum: 0
|
|
rx_csum_none: 0
|
|
rx_csum_complete: 3
|
|
rx_csum_error: 0
|
|
|
|
Driver queue specific::
|
|
|
|
tx_0_pkts: 3
|
|
tx_0_bytes: 294
|
|
tx_0_clean: 3
|
|
tx_0_dma_map_err: 0
|
|
tx_0_linearize: 0
|
|
tx_0_frags: 0
|
|
tx_0_tso: 0
|
|
tx_0_tso_bytes: 0
|
|
tx_0_csum_none: 3
|
|
tx_0_csum: 0
|
|
tx_0_vlan_inserted: 0
|
|
rx_0_pkts: 2
|
|
rx_0_bytes: 120
|
|
rx_0_dma_map_err: 0
|
|
rx_0_alloc_err: 0
|
|
rx_0_csum_none: 0
|
|
rx_0_csum_complete: 0
|
|
rx_0_csum_error: 0
|
|
rx_0_dropped: 0
|
|
rx_0_vlan_stripped: 0
|
|
|
|
Firmware port specific::
|
|
|
|
hw_tx_dropped: 0
|
|
hw_rx_dropped: 0
|
|
hw_rx_over_errors: 0
|
|
hw_rx_missed_errors: 0
|
|
hw_tx_aborted_errors: 0
|
|
frames_rx_ok: 15
|
|
frames_rx_all: 15
|
|
frames_rx_bad_fcs: 0
|
|
frames_rx_bad_all: 0
|
|
octets_rx_ok: 1290
|
|
octets_rx_all: 1290
|
|
frames_rx_unicast: 10
|
|
frames_rx_multicast: 5
|
|
frames_rx_broadcast: 0
|
|
frames_rx_pause: 0
|
|
frames_rx_bad_length: 0
|
|
frames_rx_undersized: 0
|
|
frames_rx_oversized: 0
|
|
frames_rx_fragments: 0
|
|
frames_rx_jabber: 0
|
|
frames_rx_pripause: 0
|
|
frames_rx_stomped_crc: 0
|
|
frames_rx_too_long: 0
|
|
frames_rx_vlan_good: 3
|
|
frames_rx_dropped: 0
|
|
frames_rx_less_than_64b: 0
|
|
frames_rx_64b: 4
|
|
frames_rx_65b_127b: 11
|
|
frames_rx_128b_255b: 0
|
|
frames_rx_256b_511b: 0
|
|
frames_rx_512b_1023b: 0
|
|
frames_rx_1024b_1518b: 0
|
|
frames_rx_1519b_2047b: 0
|
|
frames_rx_2048b_4095b: 0
|
|
frames_rx_4096b_8191b: 0
|
|
frames_rx_8192b_9215b: 0
|
|
frames_rx_other: 0
|
|
frames_tx_ok: 31
|
|
frames_tx_all: 31
|
|
frames_tx_bad: 0
|
|
octets_tx_ok: 2614
|
|
octets_tx_total: 2614
|
|
frames_tx_unicast: 8
|
|
frames_tx_multicast: 21
|
|
frames_tx_broadcast: 2
|
|
frames_tx_pause: 0
|
|
frames_tx_pripause: 0
|
|
frames_tx_vlan: 0
|
|
frames_tx_less_than_64b: 0
|
|
frames_tx_64b: 4
|
|
frames_tx_65b_127b: 27
|
|
frames_tx_128b_255b: 0
|
|
frames_tx_256b_511b: 0
|
|
frames_tx_512b_1023b: 0
|
|
frames_tx_1024b_1518b: 0
|
|
frames_tx_1519b_2047b: 0
|
|
frames_tx_2048b_4095b: 0
|
|
frames_tx_4096b_8191b: 0
|
|
frames_tx_8192b_9215b: 0
|
|
frames_tx_other: 0
|
|
frames_tx_pri_0: 0
|
|
frames_tx_pri_1: 0
|
|
frames_tx_pri_2: 0
|
|
frames_tx_pri_3: 0
|
|
frames_tx_pri_4: 0
|
|
frames_tx_pri_5: 0
|
|
frames_tx_pri_6: 0
|
|
frames_tx_pri_7: 0
|
|
frames_rx_pri_0: 0
|
|
frames_rx_pri_1: 0
|
|
frames_rx_pri_2: 0
|
|
frames_rx_pri_3: 0
|
|
frames_rx_pri_4: 0
|
|
frames_rx_pri_5: 0
|
|
frames_rx_pri_6: 0
|
|
frames_rx_pri_7: 0
|
|
tx_pripause_0_1us_count: 0
|
|
tx_pripause_1_1us_count: 0
|
|
tx_pripause_2_1us_count: 0
|
|
tx_pripause_3_1us_count: 0
|
|
tx_pripause_4_1us_count: 0
|
|
tx_pripause_5_1us_count: 0
|
|
tx_pripause_6_1us_count: 0
|
|
tx_pripause_7_1us_count: 0
|
|
rx_pripause_0_1us_count: 0
|
|
rx_pripause_1_1us_count: 0
|
|
rx_pripause_2_1us_count: 0
|
|
rx_pripause_3_1us_count: 0
|
|
rx_pripause_4_1us_count: 0
|
|
rx_pripause_5_1us_count: 0
|
|
rx_pripause_6_1us_count: 0
|
|
rx_pripause_7_1us_count: 0
|
|
rx_pause_1us_count: 0
|
|
frames_tx_truncated: 0
|
|
|
|
|
|
Support
|
|
=======
|
|
|
|
For general Linux networking support, please use the netdev mailing
|
|
list, which is monitored by Pensando personnel::
|
|
|
|
netdev@vger.kernel.org
|
|
|
|
For more specific support needs, please use the Pensando driver support
|
|
email::
|
|
|
|
drivers@pensando.io
|