mirror of https://gitee.com/openkylin/linux.git
324 lines
8.4 KiB
C
324 lines
8.4 KiB
C
/*
|
|
* Board-specific setup code for the ATNGW100 Network Gateway
|
|
*
|
|
* Copyright (C) 2005-2006 Atmel Corporation
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
#include <linux/clk.h>
|
|
#include <linux/etherdevice.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/irq.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/i2c-gpio.h>
|
|
#include <linux/init.h>
|
|
#include <linux/linkage.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/types.h>
|
|
#include <linux/leds.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/atmel-mci.h>
|
|
#include <linux/usb/atmel_usba_udc.h>
|
|
|
|
#include <asm/io.h>
|
|
#include <asm/setup.h>
|
|
|
|
#include <mach/at32ap700x.h>
|
|
#include <mach/board.h>
|
|
#include <mach/init.h>
|
|
#include <mach/portmux.h>
|
|
|
|
/* Oscillator frequencies. These are board-specific */
|
|
unsigned long at32_board_osc_rates[3] = {
|
|
[0] = 32768, /* 32.768 kHz on RTC osc */
|
|
[1] = 20000000, /* 20 MHz on osc0 */
|
|
[2] = 12000000, /* 12 MHz on osc1 */
|
|
};
|
|
|
|
/*
|
|
* The ATNGW100 mkII is very similar to the ATNGW100. Both have the AT32AP7000
|
|
* chip on board; the difference is that the ATNGW100 mkII has 128 MB 32-bit
|
|
* SDRAM (the ATNGW100 has 32 MB 16-bit SDRAM) and 256 MB 16-bit NAND flash
|
|
* (the ATNGW100 has none.)
|
|
*
|
|
* The RAM difference is handled by the boot loader, so the only difference we
|
|
* end up handling here is the NAND flash, EBI pin reservation and if LCDC or
|
|
* MACB1 should be enabled.
|
|
*/
|
|
#ifdef CONFIG_BOARD_ATNGW100_MKII
|
|
#include <linux/mtd/partitions.h>
|
|
#include <mach/smc.h>
|
|
|
|
static struct smc_timing nand_timing __initdata = {
|
|
.ncs_read_setup = 0,
|
|
.nrd_setup = 10,
|
|
.ncs_write_setup = 0,
|
|
.nwe_setup = 10,
|
|
|
|
.ncs_read_pulse = 30,
|
|
.nrd_pulse = 15,
|
|
.ncs_write_pulse = 30,
|
|
.nwe_pulse = 15,
|
|
|
|
.read_cycle = 30,
|
|
.write_cycle = 30,
|
|
|
|
.ncs_read_recover = 0,
|
|
.nrd_recover = 15,
|
|
.ncs_write_recover = 0,
|
|
/* WE# high -> RE# low min 60 ns */
|
|
.nwe_recover = 50,
|
|
};
|
|
|
|
static struct smc_config nand_config __initdata = {
|
|
.bus_width = 2,
|
|
.nrd_controlled = 1,
|
|
.nwe_controlled = 1,
|
|
.nwait_mode = 0,
|
|
.byte_write = 0,
|
|
.tdf_cycles = 2,
|
|
.tdf_mode = 0,
|
|
};
|
|
|
|
static struct mtd_partition nand_partitions[] = {
|
|
{
|
|
.name = "main",
|
|
.offset = 0x00000000,
|
|
.size = MTDPART_SIZ_FULL,
|
|
},
|
|
};
|
|
|
|
|
|
static struct atmel_nand_data atngw100mkii_nand_data __initdata = {
|
|
.cle = 21,
|
|
.ale = 22,
|
|
.rdy_pin = GPIO_PIN_PB(28),
|
|
.enable_pin = GPIO_PIN_PE(23),
|
|
.bus_width_16 = true,
|
|
.parts = nand_partitions,
|
|
.num_parts = ARRAY_SIZE(nand_partitions),
|
|
};
|
|
#endif
|
|
|
|
/* Initialized by bootloader-specific startup code. */
|
|
struct tag *bootloader_tags __initdata;
|
|
|
|
struct eth_addr {
|
|
u8 addr[6];
|
|
};
|
|
static struct eth_addr __initdata hw_addr[2];
|
|
static struct macb_platform_data __initdata eth_data[2];
|
|
|
|
static struct spi_board_info spi0_board_info[] __initdata = {
|
|
{
|
|
.modalias = "mtd_dataflash",
|
|
.max_speed_hz = 8000000,
|
|
.chip_select = 0,
|
|
},
|
|
};
|
|
|
|
static struct mci_platform_data __initdata mci0_data = {
|
|
.slot[0] = {
|
|
.bus_width = 4,
|
|
#if defined(CONFIG_BOARD_ATNGW100_MKII)
|
|
.detect_pin = GPIO_PIN_PC(25),
|
|
.wp_pin = GPIO_PIN_PE(22),
|
|
#else
|
|
.detect_pin = GPIO_PIN_PC(25),
|
|
.wp_pin = GPIO_PIN_PE(0),
|
|
#endif
|
|
},
|
|
};
|
|
|
|
static struct usba_platform_data atngw100_usba_data __initdata = {
|
|
#if defined(CONFIG_BOARD_ATNGW100_MKII)
|
|
.vbus_pin = GPIO_PIN_PE(26),
|
|
#else
|
|
.vbus_pin = -ENODEV,
|
|
#endif
|
|
};
|
|
|
|
/*
|
|
* The next two functions should go away as the boot loader is
|
|
* supposed to initialize the macb address registers with a valid
|
|
* ethernet address. But we need to keep it around for a while until
|
|
* we can be reasonably sure the boot loader does this.
|
|
*
|
|
* The phy_id is ignored as the driver will probe for it.
|
|
*/
|
|
static int __init parse_tag_ethernet(struct tag *tag)
|
|
{
|
|
int i;
|
|
|
|
i = tag->u.ethernet.mac_index;
|
|
if (i < ARRAY_SIZE(hw_addr))
|
|
memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address,
|
|
sizeof(hw_addr[i].addr));
|
|
|
|
return 0;
|
|
}
|
|
__tagtable(ATAG_ETHERNET, parse_tag_ethernet);
|
|
|
|
static void __init set_hw_addr(struct platform_device *pdev)
|
|
{
|
|
struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
const u8 *addr;
|
|
void __iomem *regs;
|
|
struct clk *pclk;
|
|
|
|
if (!res)
|
|
return;
|
|
if (pdev->id >= ARRAY_SIZE(hw_addr))
|
|
return;
|
|
|
|
addr = hw_addr[pdev->id].addr;
|
|
if (!is_valid_ether_addr(addr))
|
|
return;
|
|
|
|
/*
|
|
* Since this is board-specific code, we'll cheat and use the
|
|
* physical address directly as we happen to know that it's
|
|
* the same as the virtual address.
|
|
*/
|
|
regs = (void __iomem __force *)res->start;
|
|
pclk = clk_get(&pdev->dev, "pclk");
|
|
if (IS_ERR(pclk))
|
|
return;
|
|
|
|
clk_enable(pclk);
|
|
__raw_writel((addr[3] << 24) | (addr[2] << 16)
|
|
| (addr[1] << 8) | addr[0], regs + 0x98);
|
|
__raw_writel((addr[5] << 8) | addr[4], regs + 0x9c);
|
|
clk_disable(pclk);
|
|
clk_put(pclk);
|
|
}
|
|
|
|
void __init setup_board(void)
|
|
{
|
|
at32_map_usart(1, 0, 0); /* USART 1: /dev/ttyS0, DB9 */
|
|
at32_setup_serial_console(0);
|
|
}
|
|
|
|
static const struct gpio_led ngw_leds[] = {
|
|
{ .name = "sys", .gpio = GPIO_PIN_PA(16), .active_low = 1,
|
|
.default_trigger = "heartbeat",
|
|
},
|
|
{ .name = "a", .gpio = GPIO_PIN_PA(19), .active_low = 1, },
|
|
{ .name = "b", .gpio = GPIO_PIN_PE(19), .active_low = 1, },
|
|
};
|
|
|
|
static const struct gpio_led_platform_data ngw_led_data = {
|
|
.num_leds = ARRAY_SIZE(ngw_leds),
|
|
.leds = (void *) ngw_leds,
|
|
};
|
|
|
|
static struct platform_device ngw_gpio_leds = {
|
|
.name = "leds-gpio",
|
|
.id = -1,
|
|
.dev = {
|
|
.platform_data = (void *) &ngw_led_data,
|
|
}
|
|
};
|
|
|
|
static struct i2c_gpio_platform_data i2c_gpio_data = {
|
|
.sda_pin = GPIO_PIN_PA(6),
|
|
.scl_pin = GPIO_PIN_PA(7),
|
|
.sda_is_open_drain = 1,
|
|
.scl_is_open_drain = 1,
|
|
.udelay = 2, /* close to 100 kHz */
|
|
};
|
|
|
|
static struct platform_device i2c_gpio_device = {
|
|
.name = "i2c-gpio",
|
|
.id = 0,
|
|
.dev = {
|
|
.platform_data = &i2c_gpio_data,
|
|
},
|
|
};
|
|
|
|
static struct i2c_board_info __initdata i2c_info[] = {
|
|
/* NOTE: original ATtiny24 firmware is at address 0x0b */
|
|
};
|
|
|
|
static int __init atngw100_init(void)
|
|
{
|
|
unsigned i;
|
|
|
|
/*
|
|
* ATNGW100 mkII uses 32-bit SDRAM interface. Reserve the
|
|
* SDRAM-specific pins so that nobody messes with them.
|
|
*/
|
|
#ifdef CONFIG_BOARD_ATNGW100_MKII
|
|
at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);
|
|
|
|
smc_set_timing(&nand_config, &nand_timing);
|
|
smc_set_configuration(3, &nand_config);
|
|
at32_add_device_nand(0, &atngw100mkii_nand_data);
|
|
#endif
|
|
|
|
at32_add_device_usart(0);
|
|
|
|
set_hw_addr(at32_add_device_eth(0, ð_data[0]));
|
|
#ifndef CONFIG_BOARD_ATNGW100_MKII_LCD
|
|
set_hw_addr(at32_add_device_eth(1, ð_data[1]));
|
|
#endif
|
|
|
|
at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
|
|
at32_add_device_mci(0, &mci0_data);
|
|
at32_add_device_usba(0, &atngw100_usba_data);
|
|
|
|
for (i = 0; i < ARRAY_SIZE(ngw_leds); i++) {
|
|
at32_select_gpio(ngw_leds[i].gpio,
|
|
AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
|
|
}
|
|
platform_device_register(&ngw_gpio_leds);
|
|
|
|
/* all these i2c/smbus pins should have external pullups for
|
|
* open-drain sharing among all I2C devices. SDA and SCL do;
|
|
* PB28/EXTINT3 (ATNGW100) and PE21 (ATNGW100 mkII) doesn't; it should
|
|
* be SMBALERT# (for PMBus), but it's not available off-board.
|
|
*/
|
|
#ifdef CONFIG_BOARD_ATNGW100_MKII
|
|
at32_select_periph(GPIO_PIOE_BASE, 1 << 21, 0, AT32_GPIOF_PULLUP);
|
|
#else
|
|
at32_select_periph(GPIO_PIOB_BASE, 1 << 28, 0, AT32_GPIOF_PULLUP);
|
|
#endif
|
|
at32_select_gpio(i2c_gpio_data.sda_pin,
|
|
AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
|
|
at32_select_gpio(i2c_gpio_data.scl_pin,
|
|
AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
|
|
platform_device_register(&i2c_gpio_device);
|
|
i2c_register_board_info(0, i2c_info, ARRAY_SIZE(i2c_info));
|
|
|
|
return 0;
|
|
}
|
|
postcore_initcall(atngw100_init);
|
|
|
|
static int __init atngw100_arch_init(void)
|
|
{
|
|
/* PB30 (ATNGW100) and PE30 (ATNGW100 mkII) is the otherwise unused
|
|
* jumper on the mainboard, with an external pullup; the jumper grounds
|
|
* it. Use it however you like, including letting U-Boot or Linux tweak
|
|
* boot sequences.
|
|
*/
|
|
#ifdef CONFIG_BOARD_ATNGW100_MKII
|
|
at32_select_gpio(GPIO_PIN_PE(30), 0);
|
|
gpio_request(GPIO_PIN_PE(30), "j15");
|
|
gpio_direction_input(GPIO_PIN_PE(30));
|
|
gpio_export(GPIO_PIN_PE(30), false);
|
|
#else
|
|
at32_select_gpio(GPIO_PIN_PB(30), 0);
|
|
gpio_request(GPIO_PIN_PB(30), "j15");
|
|
gpio_direction_input(GPIO_PIN_PB(30));
|
|
gpio_export(GPIO_PIN_PB(30), false);
|
|
#endif
|
|
|
|
/* set_irq_type() after the arch_initcall for EIC has run, and
|
|
* before the I2C subsystem could try using this IRQ.
|
|
*/
|
|
return irq_set_irq_type(AT32_EXTINT(3), IRQ_TYPE_EDGE_FALLING);
|
|
}
|
|
arch_initcall(atngw100_arch_init);
|