openkylin
/
linux
mirror of https://gitee.com/openkylin/linux.git
9
0
Fork 0
Code Issues Projects Releases Wiki Activity
linux/drivers/ata/pata_via.c

717 lines
20 KiB
C
Raw Blame History

/*
* pata_via.c - VIA PATA for new ATA layer
* (C) 2005-2006 Red Hat Inc
*
* Documentation
* Most chipset documentation available under NDA only
*
* VIA version guide
* VIA VT82C561 - early design, uses ata_generic currently
* VIA VT82C576 - MWDMA, 33Mhz
* VIA VT82C586 - MWDMA, 33Mhz
* VIA VT82C586a - Added UDMA to 33Mhz
* VIA VT82C586b - UDMA33
* VIA VT82C596a - Nonfunctional UDMA66
* VIA VT82C596b - Working UDMA66
* VIA VT82C686 - Nonfunctional UDMA66
* VIA VT82C686a - Working UDMA66
* VIA VT82C686b - Updated to UDMA100
* VIA VT8231 - UDMA100
* VIA VT8233 - UDMA100
* VIA VT8233a - UDMA133
* VIA VT8233c - UDMA100
* VIA VT8235 - UDMA133
* VIA VT8237 - UDMA133
* VIA VT8237A - UDMA133
* VIA VT8237S - UDMA133
* VIA VT8251 - UDMA133
*
* Most registers remain compatible across chips. Others start reserved
* and acquire sensible semantics if set to 1 (eg cable detect). A few
* exceptions exist, notably around the FIFO settings.
*
* One additional quirk of the VIA design is that like ALi they use few
* PCI IDs for a lot of chips.
*
* Based heavily on:
*
* Version 3.38
*
* VIA IDE driver for Linux. Supported southbridges:
*
* vt82c576, vt82c586, vt82c586a, vt82c586b, vt82c596a, vt82c596b,
* vt82c686, vt82c686a, vt82c686b, vt8231, vt8233, vt8233c, vt8233a,
* vt8235, vt8237
*
* Copyright (c) 2000-2002 Vojtech Pavlik
*
* Based on the work of:
* Michel Aubry
* Jeff Garzik
* Andre Hedrick
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/gfp.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <linux/dmi.h>
#define DRV_NAME "pata_via"
#define DRV_VERSION "0.3.4"
enum {
VIA_BAD_PREQ = 0x01, /* Crashes if PREQ# till DDACK# set */
VIA_BAD_CLK66 = 0x02, /* 66 MHz clock doesn't work correctly */
VIA_SET_FIFO = 0x04, /* Needs to have FIFO split set */
VIA_NO_UNMASK = 0x08, /* Doesn't work with IRQ unmasking on */
VIA_BAD_ID = 0x10, /* Has wrong vendor ID (0x1107) */
VIA_BAD_AST = 0x20, /* Don't touch Address Setup Timing */
VIA_NO_ENABLES = 0x40, /* Has no enablebits */
VIA_SATA_PATA = 0x80, /* SATA/PATA combined configuration */
};
enum {
VIA_IDFLAG_SINGLE = (1 << 0), /* single channel controller) */
};
/*
* VIA SouthBridge chips.
*/
static const struct via_isa_bridge {
const char *name;
u16 id;
u8 rev_min;
u8 rev_max;
u8 udma_mask;
u8 flags;
} via_isa_bridges[] = {
{ "vx855", PCI_DEVICE_ID_VIA_VX855, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
{ "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
{ "vt8261", PCI_DEVICE_ID_VIA_8261, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
{ "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
{ "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
{ "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
{ "vt6410", PCI_DEVICE_ID_VIA_6410, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_NO_ENABLES },
{ "vt6415", PCI_DEVICE_ID_VIA_6415, 0x00, 0xff, ATA_UDMA6, VIA_BAD_AST | VIA_NO_ENABLES },
{ "vt8237a", PCI_DEVICE_ID_VIA_8237A, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
{ "vt8237", PCI_DEVICE_ID_VIA_8237, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
{ "vt8235", PCI_DEVICE_ID_VIA_8235, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
{ "vt8233a", PCI_DEVICE_ID_VIA_8233A, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
{ "vt8233c", PCI_DEVICE_ID_VIA_8233C_0, 0x00, 0x2f, ATA_UDMA5, },
{ "vt8233", PCI_DEVICE_ID_VIA_8233_0, 0x00, 0x2f, ATA_UDMA5, },
{ "vt8231", PCI_DEVICE_ID_VIA_8231, 0x00, 0x2f, ATA_UDMA5, },
{ "vt82c686b", PCI_DEVICE_ID_VIA_82C686, 0x40, 0x4f, ATA_UDMA5, },
{ "vt82c686a", PCI_DEVICE_ID_VIA_82C686, 0x10, 0x2f, ATA_UDMA4, },
{ "vt82c686", PCI_DEVICE_ID_VIA_82C686, 0x00, 0x0f, ATA_UDMA2, VIA_BAD_CLK66 },
{ "vt82c596b", PCI_DEVICE_ID_VIA_82C596, 0x10, 0x2f, ATA_UDMA4, },
{ "vt82c596a", PCI_DEVICE_ID_VIA_82C596, 0x00, 0x0f, ATA_UDMA2, VIA_BAD_CLK66 },
{ "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x47, 0x4f, ATA_UDMA2, VIA_SET_FIFO },
{ "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x40, 0x46, ATA_UDMA2, VIA_SET_FIFO | VIA_BAD_PREQ },
{ "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x30, 0x3f, ATA_UDMA2, VIA_SET_FIFO },
{ "vt82c586a", PCI_DEVICE_ID_VIA_82C586_0, 0x20, 0x2f, ATA_UDMA2, VIA_SET_FIFO },
{ "vt82c586", PCI_DEVICE_ID_VIA_82C586_0, 0x00, 0x0f, 0x00, VIA_SET_FIFO },
{ "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, 0x00, VIA_SET_FIFO | VIA_NO_UNMASK },
{ "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, 0x00, VIA_SET_FIFO | VIA_NO_UNMASK | VIA_BAD_ID },
{ "vtxxxx", PCI_DEVICE_ID_VIA_ANON, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
{ NULL }
};
struct via_port {
u8 cached_device;
};
/*
* Cable special cases
*/
static const struct dmi_system_id cable_dmi_table[] = {
{
.ident = "Acer Ferrari 3400",
.matches = {
DMI_MATCH(DMI_BOARD_VENDOR, "Acer,Inc."),
DMI_MATCH(DMI_BOARD_NAME, "Ferrari 3400"),
},
},
{ }
};
static int via_cable_override(struct pci_dev *pdev)
{
/* Systems by DMI */
if (dmi_check_system(cable_dmi_table))
return 1;
/* Arima W730-K8/Targa Visionary 811/... */
if (pdev->subsystem_vendor == 0x161F && pdev->subsystem_device == 0x2032)
return 1;
return 0;
}
/**
* via_cable_detect - cable detection
* @ap: ATA port
*
* Perform cable detection. Actually for the VIA case the BIOS
* already did this for us. We read the values provided by the
* BIOS. If you are using an 8235 in a non-PC configuration you
* may need to update this code.
*
* Hotplug also impacts on this.
*/
static int via_cable_detect(struct ata_port *ap) {
const struct via_isa_bridge *config = ap->host->private_data;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 ata66;
if (via_cable_override(pdev))
return ATA_CBL_PATA40_SHORT;
if ((config->flags & VIA_SATA_PATA) && ap->port_no == 0)
return ATA_CBL_SATA;
/* Early chips are 40 wire */
if (config->udma_mask < ATA_UDMA4)
return ATA_CBL_PATA40;
/* UDMA 66 chips have only drive side logic */
else if (config->udma_mask < ATA_UDMA5)
return ATA_CBL_PATA_UNK;
/* UDMA 100 or later */
pci_read_config_dword(pdev, 0x50, &ata66);
/* Check both the drive cable reporting bits, we might not have
two drives */
if (ata66 & (0x10100000 >> (16 * ap->port_no)))
return ATA_CBL_PATA80;
/* Check with ACPI so we can spot BIOS reported SATA bridges */
if (ata_acpi_init_gtm(ap) &&
ata_acpi_cbl_80wire(ap, ata_acpi_init_gtm(ap)))
return ATA_CBL_PATA80;
return ATA_CBL_PATA40;
}
static int via_pre_reset(struct ata_link *link, unsigned long deadline)
{
struct ata_port *ap = link->ap;
const struct via_isa_bridge *config = ap->host->private_data;
if (!(config->flags & VIA_NO_ENABLES)) {
static const struct pci_bits via_enable_bits[] = {
{ 0x40, 1, 0x02, 0x02 },
{ 0x40, 1, 0x01, 0x01 }
};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
if (!pci_test_config_bits(pdev, &via_enable_bits[ap->port_no]))
return -ENOENT;
}
return ata_sff_prereset(link, deadline);
}
/**
* via_do_set_mode - set transfer mode data
* @ap: ATA interface
* @adev: ATA device
* @mode: ATA mode being programmed
* @set_ast: Set to program address setup
* @udma_type: UDMA mode/format of registers
*
* Program the VIA registers for DMA and PIO modes. Uses the ata timing
* support in order to compute modes.
*
* FIXME: Hotplug will require we serialize multiple mode changes
* on the two channels.
*/
static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev,
int mode, int set_ast, int udma_type)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct ata_device *peer = ata_dev_pair(adev);
struct ata_timing t, p;
static int via_clock = 33333; /* Bus clock in kHZ */
unsigned long T = 1000000000 / via_clock;
unsigned long UT = T;
int ut;
int offset = 3 - (2*ap->port_no) - adev->devno;
switch (udma_type) {
case ATA_UDMA4:
UT = T / 2; break;
case ATA_UDMA5:
UT = T / 3; break;
case ATA_UDMA6:
UT = T / 4; break;
}
/* Calculate the timing values we require */
ata_timing_compute(adev, mode, &t, T, UT);
/* We share 8bit timing so we must merge the constraints */
if (peer) {
if (peer->pio_mode) {
ata_timing_compute(peer, peer->pio_mode, &p, T, UT);
ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT);
}
}
/* Address setup is programmable but breaks on UDMA133 setups */
if (set_ast) {
u8 setup; /* 2 bits per drive */
int shift = 2 * offset;
pci_read_config_byte(pdev, 0x4C, &setup);
setup &= ~(3 << shift);
setup |= (clamp_val(t.setup, 1, 4) - 1) << shift;
pci_write_config_byte(pdev, 0x4C, setup);
}
/* Load the PIO mode bits */
pci_write_config_byte(pdev, 0x4F - ap->port_no,
((clamp_val(t.act8b, 1, 16) - 1) << 4) | (clamp_val(t.rec8b, 1, 16) - 1));
pci_write_config_byte(pdev, 0x48 + offset,
((clamp_val(t.active, 1, 16) - 1) << 4) | (clamp_val(t.recover, 1, 16) - 1));
/* Load the UDMA bits according to type */
switch (udma_type) {
case ATA_UDMA2:
default:
ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 5) - 2)) : 0x03;
break;
case ATA_UDMA4:
ut = t.udma ? (0xe8 | (clamp_val(t.udma, 2, 9) - 2)) : 0x0f;
break;
case ATA_UDMA5:
ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
break;
case ATA_UDMA6:
ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
break;
}
/* Set UDMA unless device is not UDMA capable */
if (udma_type) {
u8 udma_etc;
pci_read_config_byte(pdev, 0x50 + offset, &udma_etc);
/* clear transfer mode bit */
udma_etc &= ~0x20;
if (t.udma) {
/* preserve 80-wire cable detection bit */
udma_etc &= 0x10;
udma_etc |= ut;
}
pci_write_config_byte(pdev, 0x50 + offset, udma_etc);
}
}
static void via_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
const struct via_isa_bridge *config = ap->host->private_data;
int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1;
via_do_set_mode(ap, adev, adev->pio_mode, set_ast, config->udma_mask);
}
static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
const struct via_isa_bridge *config = ap->host->private_data;
int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1;
via_do_set_mode(ap, adev, adev->dma_mode, set_ast, config->udma_mask);
}
/**
* via_mode_filter - filter buggy device/mode pairs
* @dev: ATA device
* @mask: Mode bitmask
*
* We need to apply some minimal filtering for old controllers and at least
* one breed of Transcend SSD. Return the updated mask.
*/
static unsigned long via_mode_filter(struct ata_device *dev, unsigned long mask)
{
struct ata_host *host = dev->link->ap->host;
const struct via_isa_bridge *config = host->private_data;
unsigned char model_num[ATA_ID_PROD_LEN + 1];
if (config->id == PCI_DEVICE_ID_VIA_82C586_0) {
ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
if (strcmp(model_num, "TS64GSSD25-M") == 0) {
ata_dev_printk(dev, KERN_WARNING,
"disabling UDMA mode due to reported lockups with this device.\n");
mask &= ~ ATA_MASK_UDMA;
}
}
return mask;
}
/**
* via_tf_load - send taskfile registers to host controller
* @ap: Port to which output is sent
* @tf: ATA taskfile register set
*
* Outputs ATA taskfile to standard ATA host controller.
*
* Note: This is to fix the internal bug of via chipsets, which
* will reset the device register after changing the IEN bit on
* ctl register
*/
static void via_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
struct via_port *vp = ap->private_data;
unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
int newctl = 0;
if (tf->ctl != ap->last_ctl) {
iowrite8(tf->ctl, ioaddr->ctl_addr);
ap->last_ctl = tf->ctl;
ata_wait_idle(ap);
newctl = 1;
}
if (tf->flags & ATA_TFLAG_DEVICE) {
iowrite8(tf->device, ioaddr->device_addr);
vp->cached_device = tf->device;
} else if (newctl)
iowrite8(vp->cached_device, ioaddr->device_addr);
if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
WARN_ON_ONCE(!ioaddr->ctl_addr);
iowrite8(tf->hob_feature, ioaddr->feature_addr);
iowrite8(tf->hob_nsect, ioaddr->nsect_addr);
iowrite8(tf->hob_lbal, ioaddr->lbal_addr);
iowrite8(tf->hob_lbam, ioaddr->lbam_addr);
iowrite8(tf->hob_lbah, ioaddr->lbah_addr);
VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
tf->hob_feature,
tf->hob_nsect,
tf->hob_lbal,
tf->hob_lbam,
tf->hob_lbah);
}
if (is_addr) {
iowrite8(tf->feature, ioaddr->feature_addr);
iowrite8(tf->nsect, ioaddr->nsect_addr);
iowrite8(tf->lbal, ioaddr->lbal_addr);
iowrite8(tf->lbam, ioaddr->lbam_addr);
iowrite8(tf->lbah, ioaddr->lbah_addr);
VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
tf->feature,
tf->nsect,
tf->lbal,
tf->lbam,
tf->lbah);
}
}
static int via_port_start(struct ata_port *ap)
{
struct via_port *vp;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int ret = ata_bmdma_port_start(ap);
if (ret < 0)
return ret;
vp = devm_kzalloc(&pdev->dev, sizeof(struct via_port), GFP_KERNEL);
if (vp == NULL)
return -ENOMEM;
ap->private_data = vp;
return 0;
}
static struct scsi_host_template via_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
static struct ata_port_operations via_port_ops = {
.inherits = &ata_bmdma_port_ops,
.cable_detect = via_cable_detect,
.set_piomode = via_set_piomode,
.set_dmamode = via_set_dmamode,
.prereset = via_pre_reset,
.sff_tf_load = via_tf_load,
.port_start = via_port_start,
.mode_filter = via_mode_filter,
};
static struct ata_port_operations via_port_ops_noirq = {
.inherits = &via_port_ops,
.sff_data_xfer = ata_sff_data_xfer_noirq,
};
/**
* via_config_fifo - set up the FIFO
* @pdev: PCI device
* @flags: configuration flags
*
* Set the FIFO properties for this device if necessary. Used both on
* set up and on and the resume path
*/
static void via_config_fifo(struct pci_dev *pdev, unsigned int flags)
{
u8 enable;
/* 0x40 low bits indicate enabled channels */
pci_read_config_byte(pdev, 0x40 , &enable);
enable &= 3;
if (flags & VIA_SET_FIFO) {
static const u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20};
u8 fifo;
pci_read_config_byte(pdev, 0x43, &fifo);
/* Clear PREQ# until DDACK# for errata */
if (flags & VIA_BAD_PREQ)
fifo &= 0x7F;
else
fifo &= 0x9f;
/* Turn on FIFO for enabled channels */
fifo |= fifo_setting[enable];
pci_write_config_byte(pdev, 0x43, fifo);
}
}
/**
* via_init_one - discovery callback
* @pdev: PCI device
* @id: PCI table info
*
* A VIA IDE interface has been discovered. Figure out what revision
* and perform configuration work before handing it to the ATA layer
*/
static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
/* Early VIA without UDMA support */
static const struct ata_port_info via_mwdma_info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.port_ops = &via_port_ops
};
/* Ditto with IRQ masking required */
static const struct ata_port_info via_mwdma_info_borked = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.port_ops = &via_port_ops_noirq,
};
/* VIA UDMA 33 devices (and borked 66) */
static const struct ata_port_info via_udma33_info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA2,
.port_ops = &via_port_ops
};
/* VIA UDMA 66 devices */
static const struct ata_port_info via_udma66_info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA4,
.port_ops = &via_port_ops
};
/* VIA UDMA 100 devices */
static const struct ata_port_info via_udma100_info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA5,
.port_ops = &via_port_ops
};
/* UDMA133 with bad AST (All current 133) */
static const struct ata_port_info via_udma133_info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6, /* FIXME: should check north bridge */
.port_ops = &via_port_ops
};
const struct ata_port_info *ppi[] = { NULL, NULL };
struct pci_dev *isa;
const struct via_isa_bridge *config;
static int printed_version;
u8 enable;
u32 timing;
unsigned long flags = id->driver_data;
int rc;
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
rc = pcim_enable_device(pdev);
if (rc)
return rc;
if (flags & VIA_IDFLAG_SINGLE)
ppi[1] = &ata_dummy_port_info;
/* To find out how the IDE will behave and what features we
actually have to look at the bridge not the IDE controller */
for (config = via_isa_bridges; config->id != PCI_DEVICE_ID_VIA_ANON;
config++)
if ((isa = pci_get_device(PCI_VENDOR_ID_VIA +
!!(config->flags & VIA_BAD_ID),
config->id, NULL))) {
u8 rev = isa->revision;
pci_dev_put(isa);
if ((id->device == 0x0415 || id->device == 0x3164) &&
(config->id != id->device))
continue;
if (rev >= config->rev_min && rev <= config->rev_max)
break;
}
if (!(config->flags & VIA_NO_ENABLES)) {
/* 0x40 low bits indicate enabled channels */
pci_read_config_byte(pdev, 0x40 , &enable);
enable &= 3;
if (enable == 0)
return -ENODEV;
}
/* Initialise the FIFO for the enabled channels. */
via_config_fifo(pdev, config->flags);
/* Clock set up */
switch (config->udma_mask) {
case 0x00:
if (config->flags & VIA_NO_UNMASK)
ppi[0] = &via_mwdma_info_borked;
else
ppi[0] = &via_mwdma_info;
break;
case ATA_UDMA2:
ppi[0] = &via_udma33_info;
break;
case ATA_UDMA4:
ppi[0] = &via_udma66_info;
break;
case ATA_UDMA5:
ppi[0] = &via_udma100_info;
break;
case ATA_UDMA6:
ppi[0] = &via_udma133_info;
break;
default:
WARN_ON(1);
return -ENODEV;
}
if (config->flags & VIA_BAD_CLK66) {
/* Disable the 66MHz clock on problem devices */
pci_read_config_dword(pdev, 0x50, &timing);
timing &= ~0x80008;
pci_write_config_dword(pdev, 0x50, timing);
}
/* We have established the device type, now fire it up */
return ata_pci_sff_init_one(pdev, ppi, &via_sht, (void *)config, 0);
}
#ifdef CONFIG_PM
/**
* via_reinit_one - reinit after resume
* @pdev; PCI device
*
* Called when the VIA PATA device is resumed. We must then
* reconfigure the fifo and other setup we may have altered. In
* addition the kernel needs to have the resume methods on PCI
* quirk supported.
*/
static int via_reinit_one(struct pci_dev *pdev)
{
u32 timing;
struct ata_host *host = dev_get_drvdata(&pdev->dev);
const struct via_isa_bridge *config = host->private_data;
int rc;
rc = ata_pci_device_do_resume(pdev);
if (rc)
return rc;
via_config_fifo(pdev, config->flags);
if (config->udma_mask == ATA_UDMA4) {
/* The 66 MHz devices require we enable the clock */
pci_read_config_dword(pdev, 0x50, &timing);
timing |= 0x80008;
pci_write_config_dword(pdev, 0x50, timing);
}
if (config->flags & VIA_BAD_CLK66) {
/* Disable the 66MHz clock on problem devices */
pci_read_config_dword(pdev, 0x50, &timing);
timing &= ~0x80008;
pci_write_config_dword(pdev, 0x50, timing);
}
ata_host_resume(host);
return 0;
}
#endif
static const struct pci_device_id via[] = {
{ PCI_VDEVICE(VIA, 0x0415), },
{ PCI_VDEVICE(VIA, 0x0571), },
{ PCI_VDEVICE(VIA, 0x0581), },
{ PCI_VDEVICE(VIA, 0x1571), },
{ PCI_VDEVICE(VIA, 0x3164), },
{ PCI_VDEVICE(VIA, 0x5324), },
{ PCI_VDEVICE(VIA, 0xC409), VIA_IDFLAG_SINGLE },
{ PCI_VDEVICE(VIA, 0x9001), VIA_IDFLAG_SINGLE },
{ },
};
static struct pci_driver via_pci_driver = {
.name = DRV_NAME,
.id_table = via,
.probe = via_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = via_reinit_one,
#endif
};
static int __init via_init(void)
{
return pci_register_driver(&via_pci_driver);
}
static void __exit via_exit(void)
{
pci_unregister_driver(&via_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for VIA PATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, via);
MODULE_VERSION(DRV_VERSION);
module_init(via_init);
module_exit(via_exit);
Reference in New Issue View Git Blame Copy Permalink