mirror of https://gitee.com/openkylin/linux.git
979 lines
37 KiB
Plaintext
979 lines
37 KiB
Plaintext
ThinkPad ACPI Extras Driver
|
|
|
|
Version 0.14
|
|
April 21st, 2007
|
|
|
|
Borislav Deianov <borislav@users.sf.net>
|
|
Henrique de Moraes Holschuh <hmh@hmh.eng.br>
|
|
http://ibm-acpi.sf.net/
|
|
|
|
|
|
This is a Linux driver for the IBM and Lenovo ThinkPad laptops. It
|
|
supports various features of these laptops which are accessible
|
|
through the ACPI and ACPI EC framework, but not otherwise fully
|
|
supported by the generic Linux ACPI drivers.
|
|
|
|
This driver used to be named ibm-acpi until kernel 2.6.21 and release
|
|
0.13-20070314. It used to be in the drivers/acpi tree, but it was
|
|
moved to the drivers/misc tree and renamed to thinkpad-acpi for kernel
|
|
2.6.22, and release 0.14.
|
|
|
|
|
|
Status
|
|
------
|
|
|
|
The features currently supported are the following (see below for
|
|
detailed description):
|
|
|
|
- Fn key combinations
|
|
- Bluetooth enable and disable
|
|
- video output switching, expansion control
|
|
- ThinkLight on and off
|
|
- limited docking and undocking
|
|
- UltraBay eject
|
|
- CMOS control
|
|
- LED control
|
|
- ACPI sounds
|
|
- temperature sensors
|
|
- Experimental: embedded controller register dump
|
|
- LCD brightness control
|
|
- Volume control
|
|
- Fan control and monitoring: fan speed, fan enable/disable
|
|
- Experimental: WAN enable and disable
|
|
|
|
A compatibility table by model and feature is maintained on the web
|
|
site, http://ibm-acpi.sf.net/. I appreciate any success or failure
|
|
reports, especially if they add to or correct the compatibility table.
|
|
Please include the following information in your report:
|
|
|
|
- ThinkPad model name
|
|
- a copy of your DSDT, from /proc/acpi/dsdt
|
|
- a copy of the output of dmidecode, with serial numbers
|
|
and UUIDs masked off
|
|
- which driver features work and which don't
|
|
- the observed behavior of non-working features
|
|
|
|
Any other comments or patches are also more than welcome.
|
|
|
|
|
|
Installation
|
|
------------
|
|
|
|
If you are compiling this driver as included in the Linux kernel
|
|
sources, simply enable the CONFIG_THINKPAD_ACPI option, and optionally
|
|
enable the CONFIG_THINKPAD_ACPI_BAY option if you want the
|
|
thinkpad-specific bay functionality.
|
|
|
|
Features
|
|
--------
|
|
|
|
The driver exports two different interfaces to userspace, which can be
|
|
used to access the features it provides. One is a legacy procfs-based
|
|
interface, which will be removed at some time in the distant future.
|
|
The other is a new sysfs-based interface which is not complete yet.
|
|
|
|
The procfs interface creates the /proc/acpi/ibm directory. There is a
|
|
file under that directory for each feature it supports. The procfs
|
|
interface is mostly frozen, and will change very little if at all: it
|
|
will not be extended to add any new functionality in the driver, instead
|
|
all new functionality will be implemented on the sysfs interface.
|
|
|
|
The sysfs interface tries to blend in the generic Linux sysfs subsystems
|
|
and classes as much as possible. Since some of these subsystems are not
|
|
yet ready or stabilized, it is expected that this interface will change,
|
|
and any and all userspace programs must deal with it.
|
|
|
|
|
|
Notes about the sysfs interface:
|
|
|
|
Unlike what was done with the procfs interface, correctness when talking
|
|
to the sysfs interfaces will be enforced, as will correctness in the
|
|
thinkpad-acpi's implementation of sysfs interfaces.
|
|
|
|
Also, any bugs in the thinkpad-acpi sysfs driver code or in the
|
|
thinkpad-acpi's implementation of the sysfs interfaces will be fixed for
|
|
maximum correctness, even if that means changing an interface in
|
|
non-compatible ways. As these interfaces mature both in the kernel and
|
|
in thinkpad-acpi, such changes should become quite rare.
|
|
|
|
Applications interfacing to the thinkpad-acpi sysfs interfaces must
|
|
follow all sysfs guidelines and correctly process all errors (the sysfs
|
|
interface makes extensive use of errors). File descriptors and open /
|
|
close operations to the sysfs inodes must also be properly implemented.
|
|
|
|
The version of thinkpad-acpi's sysfs interface is exported by the driver
|
|
as a driver attribute (see below).
|
|
|
|
Sysfs driver attributes are on the driver's sysfs attribute space,
|
|
for 2.6.20 this is /sys/bus/platform/drivers/thinkpad-acpi/.
|
|
|
|
Sysfs device attributes are on the driver's sysfs attribute space,
|
|
for 2.6.20 this is /sys/devices/platform/thinkpad-acpi/.
|
|
|
|
Driver version
|
|
--------------
|
|
|
|
procfs: /proc/acpi/ibm/driver
|
|
sysfs driver attribute: version
|
|
|
|
The driver name and version. No commands can be written to this file.
|
|
|
|
Sysfs interface version
|
|
-----------------------
|
|
|
|
sysfs driver attribute: interface_version
|
|
|
|
Version of the thinkpad-acpi sysfs interface, as an unsigned long
|
|
(output in hex format: 0xAAAABBCC), where:
|
|
AAAA - major revision
|
|
BB - minor revision
|
|
CC - bugfix revision
|
|
|
|
The sysfs interface version changelog for the driver can be found at the
|
|
end of this document. Changes to the sysfs interface done by the kernel
|
|
subsystems are not documented here, nor are they tracked by this
|
|
attribute.
|
|
|
|
Hot keys
|
|
--------
|
|
|
|
procfs: /proc/acpi/ibm/hotkey
|
|
sysfs device attribute: hotkey_*
|
|
|
|
Without this driver, only the Fn-F4 key (sleep button) generates an
|
|
ACPI event. With the driver loaded, the hotkey feature enabled and the
|
|
mask set (see below), the various hot keys generate ACPI events in the
|
|
following format:
|
|
|
|
ibm/hotkey HKEY 00000080 0000xxxx
|
|
|
|
The last four digits vary depending on the key combination pressed.
|
|
All labeled Fn-Fx key combinations generate distinct events. In
|
|
addition, the lid microswitch and some docking station buttons may
|
|
also generate such events.
|
|
|
|
The bit mask allows some control over which hot keys generate ACPI
|
|
events. Not all bits in the mask can be modified. Not all bits that
|
|
can be modified do anything. Not all hot keys can be individually
|
|
controlled by the mask. Most recent ThinkPad models honor the
|
|
following bits (assuming the hot keys feature has been enabled):
|
|
|
|
key bit behavior when set behavior when unset
|
|
|
|
Fn-F3 always generates ACPI event
|
|
Fn-F4 always generates ACPI event
|
|
Fn-F5 0010 generate ACPI event enable/disable Bluetooth
|
|
Fn-F7 0040 generate ACPI event switch LCD and external display
|
|
Fn-F8 0080 generate ACPI event expand screen or none
|
|
Fn-F9 0100 generate ACPI event none
|
|
Fn-F12 always generates ACPI event
|
|
|
|
Some models do not support all of the above. For example, the T30 does
|
|
not support Fn-F5 and Fn-F9. Other models do not support the mask at
|
|
all. On those models, hot keys cannot be controlled individually.
|
|
|
|
Note that enabling ACPI events for some keys prevents their default
|
|
behavior. For example, if events for Fn-F5 are enabled, that key will
|
|
no longer enable/disable Bluetooth by itself. This can still be done
|
|
from an acpid handler for the ibm/hotkey event.
|
|
|
|
Note also that not all Fn key combinations are supported through
|
|
ACPI. For example, on the X40, the brightness, volume and "Access IBM"
|
|
buttons do not generate ACPI events even with this driver. They *can*
|
|
be used through the "ThinkPad Buttons" utility, see
|
|
http://www.nongnu.org/tpb/
|
|
|
|
procfs notes:
|
|
|
|
The following commands can be written to the /proc/acpi/ibm/hotkey file:
|
|
|
|
echo enable > /proc/acpi/ibm/hotkey -- enable the hot keys feature
|
|
echo disable > /proc/acpi/ibm/hotkey -- disable the hot keys feature
|
|
echo 0xffff > /proc/acpi/ibm/hotkey -- enable all possible hot keys
|
|
echo 0x0000 > /proc/acpi/ibm/hotkey -- disable all possible hot keys
|
|
... any other 4-hex-digit mask ...
|
|
echo reset > /proc/acpi/ibm/hotkey -- restore the original mask
|
|
|
|
sysfs notes:
|
|
|
|
hotkey_bios_enabled:
|
|
Returns the status of the hot keys feature when
|
|
thinkpad-acpi was loaded. Upon module unload, the hot
|
|
key feature status will be restored to this value.
|
|
|
|
0: hot keys were disabled
|
|
1: hot keys were enabled
|
|
|
|
hotkey_bios_mask:
|
|
Returns the hot keys mask when thinkpad-acpi was loaded.
|
|
Upon module unload, the hot keys mask will be restored
|
|
to this value.
|
|
|
|
hotkey_enable:
|
|
Enables/disables the hot keys feature, and reports
|
|
current status of the hot keys feature.
|
|
|
|
0: disables the hot keys feature / feature disabled
|
|
1: enables the hot keys feature / feature enabled
|
|
|
|
hotkey_mask:
|
|
bit mask to enable ACPI event generation for each hot
|
|
key (see above). Returns the current status of the hot
|
|
keys mask, and allows one to modify it.
|
|
|
|
|
|
Bluetooth
|
|
---------
|
|
|
|
procfs: /proc/acpi/ibm/bluetooth
|
|
sysfs device attribute: bluetooth_enable
|
|
|
|
This feature shows the presence and current state of a ThinkPad
|
|
Bluetooth device in the internal ThinkPad CDC slot.
|
|
|
|
Procfs notes:
|
|
|
|
If Bluetooth is installed, the following commands can be used:
|
|
|
|
echo enable > /proc/acpi/ibm/bluetooth
|
|
echo disable > /proc/acpi/ibm/bluetooth
|
|
|
|
Sysfs notes:
|
|
|
|
If the Bluetooth CDC card is installed, it can be enabled /
|
|
disabled through the "bluetooth_enable" thinkpad-acpi device
|
|
attribute, and its current status can also be queried.
|
|
|
|
enable:
|
|
0: disables Bluetooth / Bluetooth is disabled
|
|
1: enables Bluetooth / Bluetooth is enabled.
|
|
|
|
Note: this interface will be probably be superseeded by the
|
|
generic rfkill class, so it is NOT to be considered stable yet.
|
|
|
|
Video output control -- /proc/acpi/ibm/video
|
|
--------------------------------------------
|
|
|
|
This feature allows control over the devices used for video output -
|
|
LCD, CRT or DVI (if available). The following commands are available:
|
|
|
|
echo lcd_enable > /proc/acpi/ibm/video
|
|
echo lcd_disable > /proc/acpi/ibm/video
|
|
echo crt_enable > /proc/acpi/ibm/video
|
|
echo crt_disable > /proc/acpi/ibm/video
|
|
echo dvi_enable > /proc/acpi/ibm/video
|
|
echo dvi_disable > /proc/acpi/ibm/video
|
|
echo auto_enable > /proc/acpi/ibm/video
|
|
echo auto_disable > /proc/acpi/ibm/video
|
|
echo expand_toggle > /proc/acpi/ibm/video
|
|
echo video_switch > /proc/acpi/ibm/video
|
|
|
|
Each video output device can be enabled or disabled individually.
|
|
Reading /proc/acpi/ibm/video shows the status of each device.
|
|
|
|
Automatic video switching can be enabled or disabled. When automatic
|
|
video switching is enabled, certain events (e.g. opening the lid,
|
|
docking or undocking) cause the video output device to change
|
|
automatically. While this can be useful, it also causes flickering
|
|
and, on the X40, video corruption. By disabling automatic switching,
|
|
the flickering or video corruption can be avoided.
|
|
|
|
The video_switch command cycles through the available video outputs
|
|
(it simulates the behavior of Fn-F7).
|
|
|
|
Video expansion can be toggled through this feature. This controls
|
|
whether the display is expanded to fill the entire LCD screen when a
|
|
mode with less than full resolution is used. Note that the current
|
|
video expansion status cannot be determined through this feature.
|
|
|
|
Note that on many models (particularly those using Radeon graphics
|
|
chips) the X driver configures the video card in a way which prevents
|
|
Fn-F7 from working. This also disables the video output switching
|
|
features of this driver, as it uses the same ACPI methods as
|
|
Fn-F7. Video switching on the console should still work.
|
|
|
|
UPDATE: There's now a patch for the X.org Radeon driver which
|
|
addresses this issue. Some people are reporting success with the patch
|
|
while others are still having problems. For more information:
|
|
|
|
https://bugs.freedesktop.org/show_bug.cgi?id=2000
|
|
|
|
ThinkLight control -- /proc/acpi/ibm/light
|
|
------------------------------------------
|
|
|
|
The current status of the ThinkLight can be found in this file. A few
|
|
models which do not make the status available will show it as
|
|
"unknown". The available commands are:
|
|
|
|
echo on > /proc/acpi/ibm/light
|
|
echo off > /proc/acpi/ibm/light
|
|
|
|
Docking / undocking -- /proc/acpi/ibm/dock
|
|
------------------------------------------
|
|
|
|
Docking and undocking (e.g. with the X4 UltraBase) requires some
|
|
actions to be taken by the operating system to safely make or break
|
|
the electrical connections with the dock.
|
|
|
|
The docking feature of this driver generates the following ACPI events:
|
|
|
|
ibm/dock GDCK 00000003 00000001 -- eject request
|
|
ibm/dock GDCK 00000003 00000002 -- undocked
|
|
ibm/dock GDCK 00000000 00000003 -- docked
|
|
|
|
NOTE: These events will only be generated if the laptop was docked
|
|
when originally booted. This is due to the current lack of support for
|
|
hot plugging of devices in the Linux ACPI framework. If the laptop was
|
|
booted while not in the dock, the following message is shown in the
|
|
logs:
|
|
|
|
Mar 17 01:42:34 aero kernel: thinkpad_acpi: dock device not present
|
|
|
|
In this case, no dock-related events are generated but the dock and
|
|
undock commands described below still work. They can be executed
|
|
manually or triggered by Fn key combinations (see the example acpid
|
|
configuration files included in the driver tarball package available
|
|
on the web site).
|
|
|
|
When the eject request button on the dock is pressed, the first event
|
|
above is generated. The handler for this event should issue the
|
|
following command:
|
|
|
|
echo undock > /proc/acpi/ibm/dock
|
|
|
|
After the LED on the dock goes off, it is safe to eject the laptop.
|
|
Note: if you pressed this key by mistake, go ahead and eject the
|
|
laptop, then dock it back in. Otherwise, the dock may not function as
|
|
expected.
|
|
|
|
When the laptop is docked, the third event above is generated. The
|
|
handler for this event should issue the following command to fully
|
|
enable the dock:
|
|
|
|
echo dock > /proc/acpi/ibm/dock
|
|
|
|
The contents of the /proc/acpi/ibm/dock file shows the current status
|
|
of the dock, as provided by the ACPI framework.
|
|
|
|
The docking support in this driver does not take care of enabling or
|
|
disabling any other devices you may have attached to the dock. For
|
|
example, a CD drive plugged into the UltraBase needs to be disabled or
|
|
enabled separately. See the provided example acpid configuration files
|
|
for how this can be accomplished.
|
|
|
|
There is no support yet for PCI devices that may be attached to a
|
|
docking station, e.g. in the ThinkPad Dock II. The driver currently
|
|
does not recognize, enable or disable such devices. This means that
|
|
the only docking stations currently supported are the X-series
|
|
UltraBase docks and "dumb" port replicators like the Mini Dock (the
|
|
latter don't need any ACPI support, actually).
|
|
|
|
UltraBay eject -- /proc/acpi/ibm/bay
|
|
------------------------------------
|
|
|
|
Inserting or ejecting an UltraBay device requires some actions to be
|
|
taken by the operating system to safely make or break the electrical
|
|
connections with the device.
|
|
|
|
This feature generates the following ACPI events:
|
|
|
|
ibm/bay MSTR 00000003 00000000 -- eject request
|
|
ibm/bay MSTR 00000001 00000000 -- eject lever inserted
|
|
|
|
NOTE: These events will only be generated if the UltraBay was present
|
|
when the laptop was originally booted (on the X series, the UltraBay
|
|
is in the dock, so it may not be present if the laptop was undocked).
|
|
This is due to the current lack of support for hot plugging of devices
|
|
in the Linux ACPI framework. If the laptop was booted without the
|
|
UltraBay, the following message is shown in the logs:
|
|
|
|
Mar 17 01:42:34 aero kernel: thinkpad_acpi: bay device not present
|
|
|
|
In this case, no bay-related events are generated but the eject
|
|
command described below still works. It can be executed manually or
|
|
triggered by a hot key combination.
|
|
|
|
Sliding the eject lever generates the first event shown above. The
|
|
handler for this event should take whatever actions are necessary to
|
|
shut down the device in the UltraBay (e.g. call idectl), then issue
|
|
the following command:
|
|
|
|
echo eject > /proc/acpi/ibm/bay
|
|
|
|
After the LED on the UltraBay goes off, it is safe to pull out the
|
|
device.
|
|
|
|
When the eject lever is inserted, the second event above is
|
|
generated. The handler for this event should take whatever actions are
|
|
necessary to enable the UltraBay device (e.g. call idectl).
|
|
|
|
The contents of the /proc/acpi/ibm/bay file shows the current status
|
|
of the UltraBay, as provided by the ACPI framework.
|
|
|
|
EXPERIMENTAL warm eject support on the 600e/x, A22p and A3x (To use
|
|
this feature, you need to supply the experimental=1 parameter when
|
|
loading the module):
|
|
|
|
These models do not have a button near the UltraBay device to request
|
|
a hot eject but rather require the laptop to be put to sleep
|
|
(suspend-to-ram) before the bay device is ejected or inserted).
|
|
The sequence of steps to eject the device is as follows:
|
|
|
|
echo eject > /proc/acpi/ibm/bay
|
|
put the ThinkPad to sleep
|
|
remove the drive
|
|
resume from sleep
|
|
cat /proc/acpi/ibm/bay should show that the drive was removed
|
|
|
|
On the A3x, both the UltraBay 2000 and UltraBay Plus devices are
|
|
supported. Use "eject2" instead of "eject" for the second bay.
|
|
|
|
Note: the UltraBay eject support on the 600e/x, A22p and A3x is
|
|
EXPERIMENTAL and may not work as expected. USE WITH CAUTION!
|
|
|
|
CMOS control
|
|
------------
|
|
|
|
procfs: /proc/acpi/ibm/cmos
|
|
sysfs device attribute: cmos_command
|
|
|
|
This feature is used internally by the ACPI firmware to control the
|
|
ThinkLight on most newer ThinkPad models. It may also control LCD
|
|
brightness, sounds volume and more, but only on some models.
|
|
|
|
The range of valid cmos command numbers is 0 to 21, but not all have an
|
|
effect and the behavior varies from model to model. Here is the behavior
|
|
on the X40 (tpb is the ThinkPad Buttons utility):
|
|
|
|
0 - no effect but tpb reports "Volume down"
|
|
1 - no effect but tpb reports "Volume up"
|
|
2 - no effect but tpb reports "Mute on"
|
|
3 - simulate pressing the "Access IBM" button
|
|
4 - LCD brightness up
|
|
5 - LCD brightness down
|
|
11 - toggle screen expansion
|
|
12 - ThinkLight on
|
|
13 - ThinkLight off
|
|
14 - no effect but tpb reports ThinkLight status change
|
|
|
|
The cmos command interface is prone to firmware split-brain problems, as
|
|
in newer ThinkPads it is just a compatibility layer.
|
|
|
|
LED control -- /proc/acpi/ibm/led
|
|
---------------------------------
|
|
|
|
Some of the LED indicators can be controlled through this feature. The
|
|
available commands are:
|
|
|
|
echo '<led number> on' >/proc/acpi/ibm/led
|
|
echo '<led number> off' >/proc/acpi/ibm/led
|
|
echo '<led number> blink' >/proc/acpi/ibm/led
|
|
|
|
The <led number> range is 0 to 7. The set of LEDs that can be
|
|
controlled varies from model to model. Here is the mapping on the X40:
|
|
|
|
0 - power
|
|
1 - battery (orange)
|
|
2 - battery (green)
|
|
3 - UltraBase
|
|
4 - UltraBay
|
|
7 - standby
|
|
|
|
All of the above can be turned on and off and can be made to blink.
|
|
|
|
ACPI sounds -- /proc/acpi/ibm/beep
|
|
----------------------------------
|
|
|
|
The BEEP method is used internally by the ACPI firmware to provide
|
|
audible alerts in various situations. This feature allows the same
|
|
sounds to be triggered manually.
|
|
|
|
The commands are non-negative integer numbers:
|
|
|
|
echo <number> >/proc/acpi/ibm/beep
|
|
|
|
The valid <number> range is 0 to 17. Not all numbers trigger sounds
|
|
and the sounds vary from model to model. Here is the behavior on the
|
|
X40:
|
|
|
|
0 - stop a sound in progress (but use 17 to stop 16)
|
|
2 - two beeps, pause, third beep ("low battery")
|
|
3 - single beep
|
|
4 - high, followed by low-pitched beep ("unable")
|
|
5 - single beep
|
|
6 - very high, followed by high-pitched beep ("AC/DC")
|
|
7 - high-pitched beep
|
|
9 - three short beeps
|
|
10 - very long beep
|
|
12 - low-pitched beep
|
|
15 - three high-pitched beeps repeating constantly, stop with 0
|
|
16 - one medium-pitched beep repeating constantly, stop with 17
|
|
17 - stop 16
|
|
|
|
Temperature sensors
|
|
-------------------
|
|
|
|
procfs: /proc/acpi/ibm/thermal
|
|
sysfs device attributes: (hwmon) temp*_input
|
|
|
|
Most ThinkPads include six or more separate temperature sensors but
|
|
only expose the CPU temperature through the standard ACPI methods.
|
|
This feature shows readings from up to eight different sensors on older
|
|
ThinkPads, and it has experimental support for up to sixteen different
|
|
sensors on newer ThinkPads.
|
|
|
|
EXPERIMENTAL: The 16-sensors feature is marked EXPERIMENTAL because the
|
|
implementation directly accesses hardware registers and may not work as
|
|
expected. USE WITH CAUTION! To use this feature, you need to supply the
|
|
experimental=1 parameter when loading the module. When EXPERIMENTAL
|
|
mode is enabled, reading the first 8 sensors on newer ThinkPads will
|
|
also use an new experimental thermal sensor access mode.
|
|
|
|
For example, on the X40, a typical output may be:
|
|
temperatures: 42 42 45 41 36 -128 33 -128
|
|
|
|
EXPERIMENTAL: On the T43/p, a typical output may be:
|
|
temperatures: 48 48 36 52 38 -128 31 -128 48 52 48 -128 -128 -128 -128 -128
|
|
|
|
The mapping of thermal sensors to physical locations varies depending on
|
|
system-board model (and thus, on ThinkPad model).
|
|
|
|
http://thinkwiki.org/wiki/Thermal_Sensors is a public wiki page that
|
|
tries to track down these locations for various models.
|
|
|
|
Most (newer?) models seem to follow this pattern:
|
|
|
|
1: CPU
|
|
2: (depends on model)
|
|
3: (depends on model)
|
|
4: GPU
|
|
5: Main battery: main sensor
|
|
6: Bay battery: main sensor
|
|
7: Main battery: secondary sensor
|
|
8: Bay battery: secondary sensor
|
|
9-15: (depends on model)
|
|
|
|
For the R51 (source: Thomas Gruber):
|
|
2: Mini-PCI
|
|
3: Internal HDD
|
|
|
|
For the T43, T43/p (source: Shmidoax/Thinkwiki.org)
|
|
http://thinkwiki.org/wiki/Thermal_Sensors#ThinkPad_T43.2C_T43p
|
|
2: System board, left side (near PCMCIA slot), reported as HDAPS temp
|
|
3: PCMCIA slot
|
|
9: MCH (northbridge) to DRAM Bus
|
|
10: ICH (southbridge), under Mini-PCI card, under touchpad
|
|
11: Power regulator, underside of system board, below F2 key
|
|
|
|
The A31 has a very atypical layout for the thermal sensors
|
|
(source: Milos Popovic, http://thinkwiki.org/wiki/Thermal_Sensors#ThinkPad_A31)
|
|
1: CPU
|
|
2: Main Battery: main sensor
|
|
3: Power Converter
|
|
4: Bay Battery: main sensor
|
|
5: MCH (northbridge)
|
|
6: PCMCIA/ambient
|
|
7: Main Battery: secondary sensor
|
|
8: Bay Battery: secondary sensor
|
|
|
|
|
|
Procfs notes:
|
|
Readings from sensors that are not available return -128.
|
|
No commands can be written to this file.
|
|
|
|
Sysfs notes:
|
|
Sensors that are not available return the ENXIO error. This
|
|
status may change at runtime, as there are hotplug thermal
|
|
sensors, like those inside the batteries and docks.
|
|
|
|
thinkpad-acpi thermal sensors are reported through the hwmon
|
|
subsystem, and follow all of the hwmon guidelines at
|
|
Documentation/hwmon.
|
|
|
|
|
|
EXPERIMENTAL: Embedded controller register dump -- /proc/acpi/ibm/ecdump
|
|
------------------------------------------------------------------------
|
|
|
|
This feature is marked EXPERIMENTAL because the implementation
|
|
directly accesses hardware registers and may not work as expected. USE
|
|
WITH CAUTION! To use this feature, you need to supply the
|
|
experimental=1 parameter when loading the module.
|
|
|
|
This feature dumps the values of 256 embedded controller
|
|
registers. Values which have changed since the last time the registers
|
|
were dumped are marked with a star:
|
|
|
|
[root@x40 ibm-acpi]# cat /proc/acpi/ibm/ecdump
|
|
EC +00 +01 +02 +03 +04 +05 +06 +07 +08 +09 +0a +0b +0c +0d +0e +0f
|
|
EC 0x00: a7 47 87 01 fe 96 00 08 01 00 cb 00 00 00 40 00
|
|
EC 0x10: 00 00 ff ff f4 3c 87 09 01 ff 42 01 ff ff 0d 00
|
|
EC 0x20: 00 00 00 00 00 00 00 00 00 00 00 03 43 00 00 80
|
|
EC 0x30: 01 07 1a 00 30 04 00 00 *85 00 00 10 00 50 00 00
|
|
EC 0x40: 00 00 00 00 00 00 14 01 00 04 00 00 00 00 00 00
|
|
EC 0x50: 00 c0 02 0d 00 01 01 02 02 03 03 03 03 *bc *02 *bc
|
|
EC 0x60: *02 *bc *02 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
EC 0x70: 00 00 00 00 00 12 30 40 *24 *26 *2c *27 *20 80 *1f 80
|
|
EC 0x80: 00 00 00 06 *37 *0e 03 00 00 00 0e 07 00 00 00 00
|
|
EC 0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
EC 0xa0: *ff 09 ff 09 ff ff *64 00 *00 *00 *a2 41 *ff *ff *e0 00
|
|
EC 0xb0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
EC 0xc0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
EC 0xd0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
EC 0xe0: 00 00 00 00 00 00 00 00 11 20 49 04 24 06 55 03
|
|
EC 0xf0: 31 55 48 54 35 38 57 57 08 2f 45 73 07 65 6c 1a
|
|
|
|
This feature can be used to determine the register holding the fan
|
|
speed on some models. To do that, do the following:
|
|
|
|
- make sure the battery is fully charged
|
|
- make sure the fan is running
|
|
- run 'cat /proc/acpi/ibm/ecdump' several times, once per second or so
|
|
|
|
The first step makes sure various charging-related values don't
|
|
vary. The second ensures that the fan-related values do vary, since
|
|
the fan speed fluctuates a bit. The third will (hopefully) mark the
|
|
fan register with a star:
|
|
|
|
[root@x40 ibm-acpi]# cat /proc/acpi/ibm/ecdump
|
|
EC +00 +01 +02 +03 +04 +05 +06 +07 +08 +09 +0a +0b +0c +0d +0e +0f
|
|
EC 0x00: a7 47 87 01 fe 96 00 08 01 00 cb 00 00 00 40 00
|
|
EC 0x10: 00 00 ff ff f4 3c 87 09 01 ff 42 01 ff ff 0d 00
|
|
EC 0x20: 00 00 00 00 00 00 00 00 00 00 00 03 43 00 00 80
|
|
EC 0x30: 01 07 1a 00 30 04 00 00 85 00 00 10 00 50 00 00
|
|
EC 0x40: 00 00 00 00 00 00 14 01 00 04 00 00 00 00 00 00
|
|
EC 0x50: 00 c0 02 0d 00 01 01 02 02 03 03 03 03 bc 02 bc
|
|
EC 0x60: 02 bc 02 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
EC 0x70: 00 00 00 00 00 12 30 40 24 27 2c 27 21 80 1f 80
|
|
EC 0x80: 00 00 00 06 *be 0d 03 00 00 00 0e 07 00 00 00 00
|
|
EC 0x90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
EC 0xa0: ff 09 ff 09 ff ff 64 00 00 00 a2 41 ff ff e0 00
|
|
EC 0xb0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
EC 0xc0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
EC 0xd0: 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|
|
EC 0xe0: 00 00 00 00 00 00 00 00 11 20 49 04 24 06 55 03
|
|
EC 0xf0: 31 55 48 54 35 38 57 57 08 2f 45 73 07 65 6c 1a
|
|
|
|
Another set of values that varies often is the temperature
|
|
readings. Since temperatures don't change vary fast, you can take
|
|
several quick dumps to eliminate them.
|
|
|
|
You can use a similar method to figure out the meaning of other
|
|
embedded controller registers - e.g. make sure nothing else changes
|
|
except the charging or discharging battery to determine which
|
|
registers contain the current battery capacity, etc. If you experiment
|
|
with this, do send me your results (including some complete dumps with
|
|
a description of the conditions when they were taken.)
|
|
|
|
LCD brightness control
|
|
----------------------
|
|
|
|
procfs: /proc/acpi/ibm/brightness
|
|
sysfs backlight device "thinkpad_screen"
|
|
|
|
This feature allows software control of the LCD brightness on ThinkPad
|
|
models which don't have a hardware brightness slider.
|
|
|
|
It has some limitations: the LCD backlight cannot be actually turned on or off
|
|
by this interface, and in many ThinkPad models, the "dim while on battery"
|
|
functionality will be enabled by the BIOS when this interface is used, and
|
|
cannot be controlled.
|
|
|
|
The backlight control has eight levels, ranging from 0 to 7. Some of the
|
|
levels may not be distinct.
|
|
|
|
Procfs notes:
|
|
|
|
The available commands are:
|
|
|
|
echo up >/proc/acpi/ibm/brightness
|
|
echo down >/proc/acpi/ibm/brightness
|
|
echo 'level <level>' >/proc/acpi/ibm/brightness
|
|
|
|
Sysfs notes:
|
|
|
|
The interface is implemented through the backlight sysfs class, which is poorly
|
|
documented at this time.
|
|
|
|
Locate the thinkpad_screen device under /sys/class/backlight, and inside it
|
|
there will be the following attributes:
|
|
|
|
max_brightness:
|
|
Reads the maximum brightness the hardware can be set to.
|
|
The minimum is always zero.
|
|
|
|
actual_brightness:
|
|
Reads what brightness the screen is set to at this instant.
|
|
|
|
brightness:
|
|
Writes request the driver to change brightness to the given
|
|
value. Reads will tell you what brightness the driver is trying
|
|
to set the display to when "power" is set to zero and the display
|
|
has not been dimmed by a kernel power management event.
|
|
|
|
power:
|
|
power management mode, where 0 is "display on", and 1 to 3 will
|
|
dim the display backlight to brightness level 0 because
|
|
thinkpad-acpi cannot really turn the backlight off. Kernel
|
|
power management events can temporarily increase the current
|
|
power management level, i.e. they can dim the display.
|
|
|
|
|
|
Volume control -- /proc/acpi/ibm/volume
|
|
---------------------------------------
|
|
|
|
This feature allows volume control on ThinkPad models which don't have
|
|
a hardware volume knob. The available commands are:
|
|
|
|
echo up >/proc/acpi/ibm/volume
|
|
echo down >/proc/acpi/ibm/volume
|
|
echo mute >/proc/acpi/ibm/volume
|
|
echo 'level <level>' >/proc/acpi/ibm/volume
|
|
|
|
The <level> number range is 0 to 15 although not all of them may be
|
|
distinct. The unmute the volume after the mute command, use either the
|
|
up or down command (the level command will not unmute the volume).
|
|
The current volume level and mute state is shown in the file.
|
|
|
|
Fan control and monitoring: fan speed, fan enable/disable
|
|
---------------------------------------------------------
|
|
|
|
procfs: /proc/acpi/ibm/fan
|
|
sysfs device attributes: (hwmon) fan_input, pwm1, pwm1_enable
|
|
|
|
NOTE NOTE NOTE: fan control operations are disabled by default for
|
|
safety reasons. To enable them, the module parameter "fan_control=1"
|
|
must be given to thinkpad-acpi.
|
|
|
|
This feature attempts to show the current fan speed, control mode and
|
|
other fan data that might be available. The speed is read directly
|
|
from the hardware registers of the embedded controller. This is known
|
|
to work on later R, T, X and Z series ThinkPads but may show a bogus
|
|
value on other models.
|
|
|
|
Fan levels:
|
|
|
|
Most ThinkPad fans work in "levels" at the firmware interface. Level 0
|
|
stops the fan. The higher the level, the higher the fan speed, although
|
|
adjacent levels often map to the same fan speed. 7 is the highest
|
|
level, where the fan reaches the maximum recommended speed.
|
|
|
|
Level "auto" means the EC changes the fan level according to some
|
|
internal algorithm, usually based on readings from the thermal sensors.
|
|
|
|
There is also a "full-speed" level, also known as "disengaged" level.
|
|
In this level, the EC disables the speed-locked closed-loop fan control,
|
|
and drives the fan as fast as it can go, which might exceed hardware
|
|
limits, so use this level with caution.
|
|
|
|
The fan usually ramps up or down slowly from one speed to another, and
|
|
it is normal for the EC to take several seconds to react to fan
|
|
commands. The full-speed level may take up to two minutes to ramp up to
|
|
maximum speed, and in some ThinkPads, the tachometer readings go stale
|
|
while the EC is transitioning to the full-speed level.
|
|
|
|
WARNING WARNING WARNING: do not leave the fan disabled unless you are
|
|
monitoring all of the temperature sensor readings and you are ready to
|
|
enable it if necessary to avoid overheating.
|
|
|
|
An enabled fan in level "auto" may stop spinning if the EC decides the
|
|
ThinkPad is cool enough and doesn't need the extra airflow. This is
|
|
normal, and the EC will spin the fan up if the varios thermal readings
|
|
rise too much.
|
|
|
|
On the X40, this seems to depend on the CPU and HDD temperatures.
|
|
Specifically, the fan is turned on when either the CPU temperature
|
|
climbs to 56 degrees or the HDD temperature climbs to 46 degrees. The
|
|
fan is turned off when the CPU temperature drops to 49 degrees and the
|
|
HDD temperature drops to 41 degrees. These thresholds cannot
|
|
currently be controlled.
|
|
|
|
The ThinkPad's ACPI DSDT code will reprogram the fan on its own when
|
|
certain conditions are met. It will override any fan programming done
|
|
through thinkpad-acpi.
|
|
|
|
The thinkpad-acpi kernel driver can be programmed to revert the fan
|
|
level to a safe setting if userspace does not issue one of the procfs
|
|
fan commands: "enable", "disable", "level" or "watchdog", or if there
|
|
are no writes to pwm1_enable (or to pwm1 *if and only if* pwm1_enable is
|
|
set to 1, manual mode) within a configurable amount of time of up to
|
|
120 seconds. This functionality is called fan safety watchdog.
|
|
|
|
Note that the watchdog timer stops after it enables the fan. It will be
|
|
rearmed again automatically (using the same interval) when one of the
|
|
above mentioned fan commands is received. The fan watchdog is,
|
|
therefore, not suitable to protect against fan mode changes made through
|
|
means other than the "enable", "disable", and "level" procfs fan
|
|
commands, or the hwmon fan control sysfs interface.
|
|
|
|
Procfs notes:
|
|
|
|
The fan may be enabled or disabled with the following commands:
|
|
|
|
echo enable >/proc/acpi/ibm/fan
|
|
echo disable >/proc/acpi/ibm/fan
|
|
|
|
Placing a fan on level 0 is the same as disabling it. Enabling a fan
|
|
will try to place it in a safe level if it is too slow or disabled.
|
|
|
|
The fan level can be controlled with the command:
|
|
|
|
echo 'level <level>' > /proc/acpi/ibm/fan
|
|
|
|
Where <level> is an integer from 0 to 7, or one of the words "auto" or
|
|
"full-speed" (without the quotes). Not all ThinkPads support the "auto"
|
|
and "full-speed" levels. The driver accepts "disengaged" as an alias for
|
|
"full-speed", and reports it as "disengaged" for backwards
|
|
compatibility.
|
|
|
|
On the X31 and X40 (and ONLY on those models), the fan speed can be
|
|
controlled to a certain degree. Once the fan is running, it can be
|
|
forced to run faster or slower with the following command:
|
|
|
|
echo 'speed <speed>' > /proc/acpi/ibm/fan
|
|
|
|
The sustainable range of fan speeds on the X40 appears to be from about
|
|
3700 to about 7350. Values outside this range either do not have any
|
|
effect or the fan speed eventually settles somewhere in that range. The
|
|
fan cannot be stopped or started with this command. This functionality
|
|
is incomplete, and not available through the sysfs interface.
|
|
|
|
To program the safety watchdog, use the "watchdog" command.
|
|
|
|
echo 'watchdog <interval in seconds>' > /proc/acpi/ibm/fan
|
|
|
|
If you want to disable the watchdog, use 0 as the interval.
|
|
|
|
Sysfs notes:
|
|
|
|
The sysfs interface follows the hwmon subsystem guidelines for the most
|
|
part, and the exception is the fan safety watchdog.
|
|
|
|
Writes to any of the sysfs attributes may return the EINVAL error if
|
|
that operation is not supported in a given ThinkPad or if the parameter
|
|
is out-of-bounds, and EPERM if it is forbidden. They may also return
|
|
EINTR (interrupted system call), and EIO (I/O error while trying to talk
|
|
to the firmware).
|
|
|
|
Features not yet implemented by the driver return ENOSYS.
|
|
|
|
hwmon device attribute pwm1_enable:
|
|
0: PWM offline (fan is set to full-speed mode)
|
|
1: Manual PWM control (use pwm1 to set fan level)
|
|
2: Hardware PWM control (EC "auto" mode)
|
|
3: reserved (Software PWM control, not implemented yet)
|
|
|
|
Modes 0 and 2 are not supported by all ThinkPads, and the
|
|
driver is not always able to detect this. If it does know a
|
|
mode is unsupported, it will return -EINVAL.
|
|
|
|
hwmon device attribute pwm1:
|
|
Fan level, scaled from the firmware values of 0-7 to the hwmon
|
|
scale of 0-255. 0 means fan stopped, 255 means highest normal
|
|
speed (level 7).
|
|
|
|
This attribute only commands the fan if pmw1_enable is set to 1
|
|
(manual PWM control).
|
|
|
|
hwmon device attribute fan1_input:
|
|
Fan tachometer reading, in RPM. May go stale on certain
|
|
ThinkPads while the EC transitions the PWM to offline mode,
|
|
which can take up to two minutes. May return rubbish on older
|
|
ThinkPads.
|
|
|
|
driver attribute fan_watchdog:
|
|
Fan safety watchdog timer interval, in seconds. Minimum is
|
|
1 second, maximum is 120 seconds. 0 disables the watchdog.
|
|
|
|
To stop the fan: set pwm1 to zero, and pwm1_enable to 1.
|
|
|
|
To start the fan in a safe mode: set pwm1_enable to 2. If that fails
|
|
with EINVAL, try to set pwm1_enable to 1 and pwm1 to at least 128 (255
|
|
would be the safest choice, though).
|
|
|
|
|
|
EXPERIMENTAL: WAN
|
|
-----------------
|
|
|
|
procfs: /proc/acpi/ibm/wan
|
|
sysfs device attribute: wwan_enable
|
|
|
|
This feature is marked EXPERIMENTAL because the implementation
|
|
directly accesses hardware registers and may not work as expected. USE
|
|
WITH CAUTION! To use this feature, you need to supply the
|
|
experimental=1 parameter when loading the module.
|
|
|
|
This feature shows the presence and current state of a W-WAN (Sierra
|
|
Wireless EV-DO) device.
|
|
|
|
It was tested on a Lenovo Thinkpad X60. It should probably work on other
|
|
Thinkpad models which come with this module installed.
|
|
|
|
Procfs notes:
|
|
|
|
If the W-WAN card is installed, the following commands can be used:
|
|
|
|
echo enable > /proc/acpi/ibm/wan
|
|
echo disable > /proc/acpi/ibm/wan
|
|
|
|
Sysfs notes:
|
|
|
|
If the W-WAN card is installed, it can be enabled /
|
|
disabled through the "wwan_enable" thinkpad-acpi device
|
|
attribute, and its current status can also be queried.
|
|
|
|
enable:
|
|
0: disables WWAN card / WWAN card is disabled
|
|
1: enables WWAN card / WWAN card is enabled.
|
|
|
|
Note: this interface will be probably be superseeded by the
|
|
generic rfkill class, so it is NOT to be considered stable yet.
|
|
|
|
Multiple Commands, Module Parameters
|
|
------------------------------------
|
|
|
|
Multiple commands can be written to the proc files in one shot by
|
|
separating them with commas, for example:
|
|
|
|
echo enable,0xffff > /proc/acpi/ibm/hotkey
|
|
echo lcd_disable,crt_enable > /proc/acpi/ibm/video
|
|
|
|
Commands can also be specified when loading the thinkpad-acpi module,
|
|
for example:
|
|
|
|
modprobe thinkpad_acpi hotkey=enable,0xffff video=auto_disable
|
|
|
|
Enabling debugging output
|
|
-------------------------
|
|
|
|
The module takes a debug paramater which can be used to selectively
|
|
enable various classes of debugging output, for example:
|
|
|
|
modprobe ibm_acpi debug=0xffff
|
|
|
|
will enable all debugging output classes. It takes a bitmask, so
|
|
to enable more than one output class, just add their values.
|
|
|
|
Debug bitmask Description
|
|
0x0001 Initialization and probing
|
|
0x0002 Removal
|
|
|
|
There is also a kernel build option to enable more debugging
|
|
information, which may be necessary to debug driver problems.
|
|
|
|
The level of debugging information output by the driver can be changed
|
|
at runtime through sysfs, using the driver attribute debug_level. The
|
|
attribute takes the same bitmask as the debug module parameter above.
|
|
|
|
Force loading of module
|
|
-----------------------
|
|
|
|
If thinkpad-acpi refuses to detect your ThinkPad, you can try to specify
|
|
the module parameter force_load=1. Regardless of whether this works or
|
|
not, please contact ibm-acpi-devel@lists.sourceforge.net with a report.
|
|
|
|
|
|
Sysfs interface changelog:
|
|
|
|
0x000100: Initial sysfs support, as a single platform driver and
|
|
device.
|