mirror of https://gitee.com/openkylin/linux.git
65 lines
2.6 KiB
Plaintext
65 lines
2.6 KiB
Plaintext
MMUv3 initialization sequence.
|
|
|
|
The code in the initialize_mmu macro sets up MMUv3 memory mapping
|
|
identically to MMUv2 fixed memory mapping. Depending on
|
|
CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX symbol this code is
|
|
located in one of the following address ranges:
|
|
|
|
0xF0000000..0xFFFFFFFF (will keep same address in MMU v2 layout;
|
|
typically ROM)
|
|
0x00000000..0x07FFFFFF (system RAM; this code is actually linked
|
|
at 0xD0000000..0xD7FFFFFF [cached]
|
|
or 0xD8000000..0xDFFFFFFF [uncached];
|
|
in any case, initially runs elsewhere
|
|
than linked, so have to be careful)
|
|
|
|
The code has the following assumptions:
|
|
This code fragment is run only on an MMU v3.
|
|
TLBs are in their reset state.
|
|
ITLBCFG and DTLBCFG are zero (reset state).
|
|
RASID is 0x04030201 (reset state).
|
|
PS.RING is zero (reset state).
|
|
LITBASE is zero (reset state, PC-relative literals); required to be PIC.
|
|
|
|
TLB setup proceeds along the following steps.
|
|
|
|
Legend:
|
|
VA = virtual address (two upper nibbles of it);
|
|
PA = physical address (two upper nibbles of it);
|
|
pc = physical range that contains this code;
|
|
|
|
After step 2, we jump to virtual address in 0x40000000..0x5fffffff
|
|
that corresponds to next instruction to execute in this code.
|
|
After step 4, we jump to intended (linked) address of this code.
|
|
|
|
Step 0 Step1 Step 2 Step3 Step 4 Step5
|
|
============ ===== ============ ===== ============ =====
|
|
VA PA PA VA PA PA VA PA PA
|
|
------ -- -- ------ -- -- ------ -- --
|
|
E0..FF -> E0 -> E0 E0..FF -> E0 F0..FF -> F0 -> F0
|
|
C0..DF -> C0 -> C0 C0..DF -> C0 E0..EF -> F0 -> F0
|
|
A0..BF -> A0 -> A0 A0..BF -> A0 D8..DF -> 00 -> 00
|
|
80..9F -> 80 -> 80 80..9F -> 80 D0..D7 -> 00 -> 00
|
|
60..7F -> 60 -> 60 60..7F -> 60
|
|
40..5F -> 40 40..5F -> pc -> pc 40..5F -> pc
|
|
20..3F -> 20 -> 20 20..3F -> 20
|
|
00..1F -> 00 -> 00 00..1F -> 00
|
|
|
|
The default location of IO peripherals is above 0xf0000000. This may change
|
|
using a "ranges" property in a device tree simple-bus node. See ePAPR 1.1, §6.5
|
|
for details on the syntax and semantic of simple-bus nodes. The following
|
|
limitations apply:
|
|
|
|
1. Only top level simple-bus nodes are considered
|
|
|
|
2. Only one (first) simple-bus node is considered
|
|
|
|
3. Empty "ranges" properties are not supported
|
|
|
|
4. Only the first triplet in the "ranges" property is considered
|
|
|
|
5. The parent-bus-address value is rounded down to the nearest 256MB boundary
|
|
|
|
6. The IO area covers the entire 256MB segment of parent-bus-address; the
|
|
"ranges" triplet length field is ignored
|