mirror of https://gitee.com/openkylin/linux.git
78 lines
2.4 KiB
Plaintext
78 lines
2.4 KiB
Plaintext
STMicroelectronics STi MIPHY365x PHY binding
|
|
============================================
|
|
|
|
This binding describes a miphy device that is used to control PHY hardware
|
|
for SATA and PCIe.
|
|
|
|
Required properties (controller (parent) node):
|
|
- compatible : Should be "st,miphy365x-phy"
|
|
- st,syscfg : Phandle / integer array property. Phandle of sysconfig group
|
|
containing the miphy registers and integer array should contain
|
|
an entry for each port sub-node, specifying the control
|
|
register offset inside the sysconfig group.
|
|
|
|
Required nodes : A sub-node is required for each channel the controller
|
|
provides. Address range information including the usual
|
|
'reg' and 'reg-names' properties are used inside these
|
|
nodes to describe the controller's topology. These nodes
|
|
are translated by the driver's .xlate() function.
|
|
|
|
Required properties (port (child) node):
|
|
- #phy-cells : Should be 1 (See second example)
|
|
Cell after port phandle is device type from:
|
|
- PHY_TYPE_SATA
|
|
- PHY_TYPE_PCI
|
|
- reg : Address and length of register sets for each device in
|
|
"reg-names"
|
|
- reg-names : The names of the register addresses corresponding to the
|
|
registers filled in "reg":
|
|
- sata: For SATA devices
|
|
- pcie: For PCIe devices
|
|
|
|
Optional properties (port (child) node):
|
|
- st,sata-gen : Generation of locally attached SATA IP. Expected values
|
|
are {1,2,3). If not supplied generation 1 hardware will
|
|
be expected
|
|
- st,pcie-tx-pol-inv : Bool property to invert the polarity PCIe Tx (Txn/Txp)
|
|
- st,sata-tx-pol-inv : Bool property to invert the polarity SATA Tx (Txn/Txp)
|
|
|
|
Example:
|
|
|
|
miphy365x_phy: miphy365x@fe382000 {
|
|
compatible = "st,miphy365x-phy";
|
|
st,syscfg = <&syscfg_rear 0x824 0x828>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges;
|
|
|
|
phy_port0: port@fe382000 {
|
|
reg = <0xfe382000 0x100>, <0xfe394000 0x100>;
|
|
reg-names = "sata", "pcie";
|
|
#phy-cells = <1>;
|
|
st,sata-gen = <3>;
|
|
};
|
|
|
|
phy_port1: port@fe38a000 {
|
|
reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;;
|
|
reg-names = "sata", "pcie", "syscfg";
|
|
#phy-cells = <1>;
|
|
st,pcie-tx-pol-inv;
|
|
};
|
|
};
|
|
|
|
Specifying phy control of devices
|
|
=================================
|
|
|
|
Device nodes should specify the configuration required in their "phys"
|
|
property, containing a phandle to the phy port node and a device type.
|
|
|
|
Example:
|
|
|
|
#include <dt-bindings/phy/phy.h>
|
|
|
|
sata0: sata@fe380000 {
|
|
...
|
|
phys = <&phy_port0 PHY_TYPE_SATA>;
|
|
...
|
|
};
|