commit 4bc31edebde51fcf8ad0794763b8679a7ecb5ec0 upstream.
Way back in commit 4f25580fb8 ("mmc: core: changes frequency to
hs_max_dtr when selecting hs400es"), Rockchip engineers noticed that
some eMMC don't respond to SEND_STATUS commands very reliably if they're
still running at a low initial frequency. As mentioned in that commit,
JESD84-B51 P49 suggests a sequence in which the host:
1. sets HS_TIMING
2. bumps the clock ("<= 52 MHz")
3. sends further commands
It doesn't exactly require that we don't use a lower-than-52MHz
frequency, but in practice, these eMMC don't like it.
The aforementioned commit tried to get that right for HS400ES, although
it's unclear whether this ever truly worked as committed into mainline,
as other changes/refactoring adjusted the sequence in conflicting ways:
08573eaf1a ("mmc: mmc: do not use CMD13 to get status after speed mode
switch")
53e60650f7 ("mmc: core: Allow CMD13 polling when switching to HS mode
for mmc")
In any case, today we do step 3 before step 2. Let's fix that, and also
apply the same logic to HS200/400, where this eMMC has problems too.
Resolves errors like this seen when booting some RK3399 Gru/Scarlet
systems:
[ 2.058881] mmc1: CQHCI version 5.10
[ 2.097545] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
[ 2.209804] mmc1: mmc_select_hs400es failed, error -84
[ 2.215597] mmc1: error -84 whilst initialising MMC card
[ 2.417514] mmc1: mmc_select_hs400es failed, error -110
[ 2.423373] mmc1: error -110 whilst initialising MMC card
[ 2.605052] mmc1: mmc_select_hs400es failed, error -110
[ 2.617944] mmc1: error -110 whilst initialising MMC card
[ 2.835884] mmc1: mmc_select_hs400es failed, error -110
[ 2.841751] mmc1: error -110 whilst initialising MMC card
Ealier versions of this patch bumped to 200MHz/HS200 speeds too early,
which caused issues on, e.g., qcom-msm8974-fairphone-fp2. (Thanks for
the report Luca!) After a second look, it appears that aligns with
JESD84 / page 45 / table 28, so we need to keep to lower (HS / 52 MHz)
rates first.
Fixes: 08573eaf1a ("mmc: mmc: do not use CMD13 to get status after speed mode switch")
Fixes: 53e60650f7 ("mmc: core: Allow CMD13 polling when switching to HS mode for mmc")
Fixes: 4f25580fb8 ("mmc: core: changes frequency to hs_max_dtr when selecting hs400es")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/linux-mmc/11962455.O9o76ZdvQC@g550jk/
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220422100824.v4.1.I484f4ee35609f78b932bd50feed639c29e64997e@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9f3fb523dbf476dc86beea23f5b5ca8f9687c93 upstream.
Newer variants of the MMC controller support a 34-bit physical address
space by using word addresses instead of byte addresses. However, the
code truncates the DMA descriptor address to 32 bits before applying the
shift. This breaks DMA for descriptors allocated above the 32-bit limit.
Fixes: 3536b82e58 ("mmc: sunxi: add support for A100 mmc controller")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220424231751.32053-1-samuel@sholland.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb9d84b0ffe39893cb23b0b6712bbe3637fa25fa upstream.
ALSA fireworks driver has a bug in its initial state to return count
shorter than expected by 4 bytes to userspace applications when handling
response frame for Echo Audio Fireworks transaction. It's due to missing
addition of the size for the type of event in ALSA firewire stack.
Fixes: 555e8a8f7f ("ALSA: fireworks: Add command/response functionality into hwdep interface")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220424102428.21109-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b79954fd00d540677c97a560622b73f3a1f4e28 upstream.
Lenovo Yoga Duet 7 13ITL6 has Realtek ALC287 and built-in
speakers do not work out of the box. The fix developed for
Yoga 7i 14ITL5 also enables speaker output for this model.
Signed-off-by: Zihao Wang <wzhd@ustc.edu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220424084120.74125-1-wzhd@ustc.edu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b89966bc96a06f6ad65f64ae4b0461918fcc9d3 upstream.
The Linux tool "lscpu" shows the double amount of CPUs if we have
"model" and "model name" in two different lines in /proc/cpuinfo.
This change combines the model and the model name into one line.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0a6c68f69981214cb7858738dd2bc81475111f7 upstream.
Fix the discrepancy between the two places we check for the CP0 counter
erratum in along with the incorrect comparison of the R4400 revision
number against 0x30 which matches none and consistently consider all
R4000 and R4400 processors affected, as documented in processor errata
publications[1][2][3], following the mapping between CP0 PRId register
values and processor models:
PRId | Processor Model
---------+--------------------
00000422 | R4000 Revision 2.2
00000430 | R4000 Revision 3.0
00000440 | R4400 Revision 1.0
00000450 | R4400 Revision 2.0
00000460 | R4400 Revision 3.0
No other revision of either processor has ever been spotted.
Contrary to what has been stated in commit ce202cbb9e ("[MIPS] Assume
R4000/R4400 newer than 3.0 don't have the mfc0 count bug") marking the
CP0 counter as buggy does not preclude it from being used as either a
clock event or a clock source device. It just cannot be used as both at
a time, because in that case clock event interrupts will be occasionally
lost, and the use as a clock event device takes precedence.
Compare against 0x4ff in `can_use_mips_counter' so that a single machine
instruction is produced.
References:
[1] "MIPS R4000PC/SC Errata, Processor Revision 2.2 and 3.0", MIPS
Technologies Inc., May 10, 1994, Erratum 53, p.13
[2] "MIPS R4400PC/SC Errata, Processor Revision 1.0", MIPS Technologies
Inc., February 9, 1994, Erratum 21, p.4
[3] "MIPS R4400PC/SC Errata, Processor Revision 2.0 & 3.0", MIPS
Technologies Inc., January 24, 1995, Erratum 14, p.3
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: ce202cbb9e ("[MIPS] Assume R4000/R4400 newer than 3.0 don't have the mfc0 count bug")
Cc: stable@vger.kernel.org # v2.6.24+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d799769188529abc6cbf035a10087a51f7832b6b upstream.
When ld detects unaligned relocations, it emits R_PPC64_UADDR64
relocations instead of R_PPC64_RELATIVE. Currently R_PPC64_UADDR64 are
detected by arch/powerpc/tools/relocs_check.sh and expected not to work.
Below is a simple chunk to trigger this behaviour (this disables
optimization for the demonstration purposes only, this also happens with
-O1/-O2 when CONFIG_PRINTK_INDEX=y, for example):
\#pragma GCC push_options
\#pragma GCC optimize ("O0")
struct entry {
const char *file;
int line;
} __attribute__((packed));
static const struct entry e1 = { .file = __FILE__, .line = __LINE__ };
static const struct entry e2 = { .file = __FILE__, .line = __LINE__ };
...
prom_printf("e1=%s %lx %lx\n", e1.file, (unsigned long) e1.file, mfmsr());
prom_printf("e2=%s %lx\n", e2.file, (unsigned long) e2.file);
\#pragma GCC pop_options
This adds support for UADDR64 for 64bit. This reuses __dynamic_symtab
from the 32bit code which supports more relocation types already.
Because RELACOUNT includes only R_PPC64_RELATIVE, this replaces it with
RELASZ which is the size of all relocation records.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20220309061822.168173-1-aik@ozlabs.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4abff6d48dbcea8200c7ea35ba70c242d128ebf3 upstream.
Occasionally objtool driven code patching (think .static_call_sites
.retpoline_sites etc..) goes sideways and it tries to patch an
instruction that doesn't match.
Much head-scatching and cursing later the problem is as outlined below
and affects every section that objtool generates for us, very much
including the ORC data. The below uses .static_call_sites because it's
convenient for demonstration purposes, but as mentioned the ORC
sections, .retpoline_sites and __mount_loc are all similarly affected.
Consider:
foo-weak.c:
extern void __SCT__foo(void);
__attribute__((weak)) void foo(void)
{
return __SCT__foo();
}
foo.c:
extern void __SCT__foo(void);
extern void my_foo(void);
void foo(void)
{
my_foo();
return __SCT__foo();
}
These generate the obvious code
(gcc -O2 -fcf-protection=none -fno-asynchronous-unwind-tables -c foo*.c):
foo-weak.o:
0000000000000000 <foo>:
0: e9 00 00 00 00 jmpq 5 <foo+0x5> 1: R_X86_64_PLT32 __SCT__foo-0x4
foo.o:
0000000000000000 <foo>:
0: 48 83 ec 08 sub $0x8,%rsp
4: e8 00 00 00 00 callq 9 <foo+0x9> 5: R_X86_64_PLT32 my_foo-0x4
9: 48 83 c4 08 add $0x8,%rsp
d: e9 00 00 00 00 jmpq 12 <foo+0x12> e: R_X86_64_PLT32 __SCT__foo-0x4
Now, when we link these two files together, you get something like
(ld -r -o foos.o foo-weak.o foo.o):
foos.o:
0000000000000000 <foo-0x10>:
0: e9 00 00 00 00 jmpq 5 <foo-0xb> 1: R_X86_64_PLT32 __SCT__foo-0x4
5: 66 2e 0f 1f 84 00 00 00 00 00 nopw %cs:0x0(%rax,%rax,1)
f: 90 nop
0000000000000010 <foo>:
10: 48 83 ec 08 sub $0x8,%rsp
14: e8 00 00 00 00 callq 19 <foo+0x9> 15: R_X86_64_PLT32 my_foo-0x4
19: 48 83 c4 08 add $0x8,%rsp
1d: e9 00 00 00 00 jmpq 22 <foo+0x12> 1e: R_X86_64_PLT32 __SCT__foo-0x4
Noting that ld preserves the weak function text, but strips the symbol
off of it (hence objdump doing that funny negative offset thing). This
does lead to 'interesting' unused code issues with objtool when ran on
linked objects, but that seems to be working (fingers crossed).
So far so good.. Now lets consider the objtool static_call output
section (readelf output, old binutils):
foo-weak.o:
Relocation section '.rela.static_call_sites' at offset 0x2c8 contains 1 entry:
Offset Info Type Symbol's Value Symbol's Name + Addend
0000000000000000 0000000200000002 R_X86_64_PC32 0000000000000000 .text + 0
0000000000000004 0000000d00000002 R_X86_64_PC32 0000000000000000 __SCT__foo + 1
foo.o:
Relocation section '.rela.static_call_sites' at offset 0x310 contains 2 entries:
Offset Info Type Symbol's Value Symbol's Name + Addend
0000000000000000 0000000200000002 R_X86_64_PC32 0000000000000000 .text + d
0000000000000004 0000000d00000002 R_X86_64_PC32 0000000000000000 __SCT__foo + 1
foos.o:
Relocation section '.rela.static_call_sites' at offset 0x430 contains 4 entries:
Offset Info Type Symbol's Value Symbol's Name + Addend
0000000000000000 0000000100000002 R_X86_64_PC32 0000000000000000 .text + 0
0000000000000004 0000000d00000002 R_X86_64_PC32 0000000000000000 __SCT__foo + 1
0000000000000008 0000000100000002 R_X86_64_PC32 0000000000000000 .text + 1d
000000000000000c 0000000d00000002 R_X86_64_PC32 0000000000000000 __SCT__foo + 1
So we have two patch sites, one in the dead code of the weak foo and one
in the real foo. All is well.
*HOWEVER*, when the toolchain strips unused section symbols it
generates things like this (using new enough binutils):
foo-weak.o:
Relocation section '.rela.static_call_sites' at offset 0x2c8 contains 1 entry:
Offset Info Type Symbol's Value Symbol's Name + Addend
0000000000000000 0000000200000002 R_X86_64_PC32 0000000000000000 foo + 0
0000000000000004 0000000d00000002 R_X86_64_PC32 0000000000000000 __SCT__foo + 1
foo.o:
Relocation section '.rela.static_call_sites' at offset 0x310 contains 2 entries:
Offset Info Type Symbol's Value Symbol's Name + Addend
0000000000000000 0000000200000002 R_X86_64_PC32 0000000000000000 foo + d
0000000000000004 0000000d00000002 R_X86_64_PC32 0000000000000000 __SCT__foo + 1
foos.o:
Relocation section '.rela.static_call_sites' at offset 0x430 contains 4 entries:
Offset Info Type Symbol's Value Symbol's Name + Addend
0000000000000000 0000000100000002 R_X86_64_PC32 0000000000000000 foo + 0
0000000000000004 0000000d00000002 R_X86_64_PC32 0000000000000000 __SCT__foo + 1
0000000000000008 0000000100000002 R_X86_64_PC32 0000000000000000 foo + d
000000000000000c 0000000d00000002 R_X86_64_PC32 0000000000000000 __SCT__foo + 1
And now we can see how that foos.o .static_call_sites goes side-ways, we
now have _two_ patch sites in foo. One for the weak symbol at foo+0
(which is no longer a static_call site!) and one at foo+d which is in
fact the right location.
This seems to happen when objtool cannot find a section symbol, in which
case it falls back to any other symbol to key off of, however in this
case that goes terribly wrong!
As such, teach objtool to create a section symbol when there isn't
one.
Fixes: 44f6a7c075 ("objtool: Fix seg fault with Clang non-section symbols")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20220419203807.655552918@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5d20d42a2f2dc2b2f9e9361912062732414090d upstream.
Now the generic code can handle kallsyms fixup properly so no need to
keep the arch-functions anymore.
Fixes: 3cf6a32f3f2a4594 ("perf symbols: Fix symbol size calculation condition")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-s390@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20220416004048.1514900-4-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4f7d63287217ba25e5c80f5faae5e4f7118790e upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.8.1 states that XON/XOFF characters
shall be used instead of Fcon/Fcoff command in advanced option mode to
handle flow control. Chapter 5.4.8.2 describes how XON/XOFF characters
shall be handled. Basic option mode only used Fcon/Fcoff commands and no
XON/XOFF characters. These are treated as data bytes here.
The current implementation uses the gsm_mux field 'constipated' to handle
flow control from the remote peer and the gsm_dlci field 'constipated' to
handle flow control from each DLCI. The later is unrelated to this patch.
The gsm_mux field is correctly set for Fcon/Fcoff commands in
gsm_control_message(). However, the same is not true for XON/XOFF
characters in gsm1_receive().
Disable software flow control handling in the tty to allow explicit
handling by n_gsm.
Add the missing handling in advanced option mode for gsm_mux in
gsm1_receive() to comply with the standard.
This patch depends on the following commit:
Commit 8838b2af23ca ("tty: n_gsm: fix SW flow control encoding/handling")
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff9166c623704337bd6fe66fce2838d9768a6634 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.4.2 states that any received unnumbered
acknowledgment (UA) with its poll/final (PF) bit set to 0 shall be
discarded. Currently, all UA frame are handled in the same way regardless
of the PF bit. This does not comply with the standard.
Remove the UA case in gsm_queue() to process only UA frames with PF bit set
to 1 to abide the standard.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-20-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73029a4d7161f8b6c0934553145ef574d2d0c645 upstream.
gsmtty_write() and gsm_dlci_data_output() properly guard the fifo access.
However, gsm_dlci_close() and gsmtty_flush_buffer() modifies the fifo but
do not guard this.
Add a guard here to prevent race conditions on parallel writes to the fifo.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-17-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1adf6fee58ca25fb6720b8d34c919dcf5425cc9c upstream.
gsm_control_modem() informs the virtual tty that more data can be written
after receiving a control signal octet via modem status command (MSC).
However, gsm_dlci_data() fails to do the same after receiving a control
signal octet from the convergence layer type 2 header.
Add tty_wakeup() in gsm_dlci_data() for convergence layer type 2 to fix
this.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-14-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 317f86af7f5d19f286ed2d181cbaef4a188c7f19 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. The value of the modem status command (MSC) frame
contains an address field, control signal and optional break signal octet.
The address field is encoded as described in chapter 5.2.1.2 with only one
octet (may be extended to more in future versions of the standard). Whereas
the control signal and break signal octet are always one byte each. This is
strange at first glance as it makes the EA bit redundant. However, the same
two octets are also encoded as header in convergence layer type 2 as
described in chapter 5.5.2. No header length field is given and the only
way to test if there is an optional break signal octet is via the EA flag
which extends the control signal octet with a break signal octet. Now it
becomes obvious how the EA bit for those two octets shall be encoded in the
MSC frame. The current implementation treats the signal octet different for
MSC frame and convergence layer type 2 header even though the standard
describes it for both in the same way.
Use the EA bit to encode the signal octets not only in the convergence
layer type 2 header but also in the MSC frame in the same way with either
1 or 2 bytes in case of an optional break signal. Adjust the receiving path
accordingly in gsm_control_modem().
Fixes: 3ac06b9056 ("tty: n_gsm: Fix for modems with brk in modem status control")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-13-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 398867f59f956985f4c324f173eff7b946e14bd8 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.1 states that each command frame shall
be made up from type, length and value. Looking for example in chapter
5.4.6.3.5 at the description for the encoding of a flow control on command
it becomes obvious, that the type and length field is always present
whereas the value may be zero bytes long. The current implementation omits
the length field if the value is not present. This is wrong.
Correct this by always sending the length in gsm_control_transmit().
So far only the modem status command (MSC) has included a value and encoded
its length directly. Therefore, also change gsmtty_modem_update().
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-12-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0bcdffcad5a22f202e3bf37190c0dd8c080ea92 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_config() fails to limit this range correctly. Furthermore,
gsm_control_retransmit() handles this number incorrectly by performing
N2 - 1 retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix the range check in gsm_config() and the value handling in
gsm_control_send() and gsm_control_retransmit() to comply with 3GPP 27.010.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-11-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17eac652028501df7ea296b1d9b9c134db262b7d upstream.
In gsm_cleanup_mux() the muxer is closed down and all queues are removed.
However, removing the queues is done without explicit control of the
underlying buffers. Flush those before freeing up our queues to ensure
that all outgoing queues are cleared consistently. Otherwise, a new mux
connection establishment attempt may time out while the underlying tty is
still busy sending out the remaining data from the previous connection.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-10-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit deefc58bafb4841df7f0a0d85d89a1c819db9743 upstream.
The current DLCI release order starts with the control channel followed by
the user channels. Reverse this order to keep the control channel open
until all user channels have been released.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 535bf600de75a859698892ee873521a48d289ec1 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size
(N1) refers to the length of the information field (i.e. user payload).
However, 'txframe' stores the whole frame including frame header, checksum
and start/end flags. We also need to consider the byte stuffing overhead.
Define constant for the protocol overhead and adjust the 'txframe' size
calculation accordingly to reserve enough space for a complete mux frame
including byte stuffing for advanced option mode. Note that no byte
stuffing is applied to the start and end flag.
Also use MAX_MTU instead of MAX_MRU as this buffer is used for data
transmission.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-8-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 743b83f15d4069ea57c3e40996bf4a1077e0cdc1 upstream.
Check if the incoming interface is available and NFT_BREAK
in case neither skb->sk nor input device are set.
Because nf_sk_lookup_slow*() assume packet headers are in the
'in' direction, use in postrouting is not going to yield a meaningful
result. Same is true for the forward chain, so restrict the use
to prerouting, input and output.
Use in output work if a socket is already attached to the skb.
Fixes: 554ced0a6e ("netfilter: nf_tables: add support for native socket matching")
Reported-and-tested-by: Topi Miettinen <toiwoton@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a24b4b2f660b7ddf3f484b37600bba382cb28a9d upstream.
The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06d5afd4d640eea67f5623e76cd5fc03359b7f3c upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in
convergence layer type 2 can be either one or two bytes. The length is
encoded in the EA bit. This is set 1 for the last byte in the sequence.
gsmtty_modem_update() handles this correctly but gsm_dlci_data_output()
fails to set EA to 1. There is no case in which we encode two signal octets
as there is no case in which we send out a break signal.
Therefore, always set the EA bit to 1 for the signal octet to fix this.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 284260f278b706364fb4c88a7b56ba5298d5973c upstream.
Internally, we manage the alive state of the mux channels and mux itself
with the field member 'dead'. This makes it possible to notify the user
if the accessed underlying link is already gone. On the other hand,
however, removing the virtual ttys before terminating the channels may
result in peer messages being received without any internal target. Move
the mux cleanup procedure from gsmld_detach_gsm() to gsmld_close() to fix
this by keeping the virtual ttys open until the mux has been cleaned up.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ec92e9742774bf42614fceea3bf6b50c9409225 upstream.
The active mux instances are managed in the gsm_mux array and via mux_get()
and mux_put() functions separately. This gives a very loose coupling
between the actual instance and the gsm_mux array which manages it. It also
results in unnecessary lockings which makes it prone to failures. And it
creates a race condition if more than the maximum number of mux instances
are requested while the user changes the parameters of an active instance.
The user may loose ownership of the current mux instance in this case.
Fix this by moving the gsm_mux array handling to the mux allocation and
deallocation functions.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa371e96f05dcb36a88298f5cb70aa7234d5e8b8 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.8.2 states that both sides will revert to
the non-multiplexed mode via a close-down message (CLD). The usual program
flow is as following:
- start multiplex mode by sending AT+CMUX to the mobile
- establish the control channel (DLCI 0)
- establish user channels (DLCI >0)
- terminate user channels
- send close-down message (CLD)
- revert to AT protocol (i.e. leave multiplexed mode)
The AT protocol is out of scope of the n_gsm driver. However,
gsm_disconnect() sends CLD if gsm_config() detects that the requested
parameters require the mux protocol to restart. The next immediate action
is to start the mux protocol by opening DLCI 0 again. Any responder side
which handles CLD commands correctly forces us to fail at this point
because AT+CMUX needs to be sent to the mobile to start the mux again.
Therefore, remove the CLD command in this phase and keep both sides in
multiplexed mode.
Remove the gsm_disconnect() function as it become unnecessary and merge the
remaining parts into gsm_cleanup_mux() to handle the termination order and
locking correctly.
Fixes: 71e0779153 ("tty: n_gsm: do not send/receive in ldisc close path")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8799ebce84d672aae1dc3170510f6a3e66f96b11 upstream.
Now arch-specific functions all do the same thing. When it fixes the
symbol address it needs to check the boundary between the kernel image
and modules. For the last symbol in the previous region, it cannot
know the exact size as it's discarded already. Thus it just uses a
small page size (4096) and rounds it up like the last symbol.
Fixes: 3cf6a32f3f2a4594 ("perf symbols: Fix symbol size calculation condition")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-s390@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20220416004048.1514900-3-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 838425f2defe5262906b698752d28fd2fca1aac2 upstream.
The symbol fixup is necessary for symbols in kallsyms since they don't
have size info. So we use the next symbol's address to calculate the
size. Now it's also used for user binaries because sometimes they miss
size for hand-written asm functions.
There's a arch-specific function to handle kallsyms differently but
currently it cannot distinguish kallsyms from others. Pass this
information explicitly to handle it properly. Note that those arch
functions will be moved to the generic function so I didn't added it to
the arch-functions.
Fixes: 3cf6a32f3f2a4594 ("perf symbols: Fix symbol size calculation condition")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-s390@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20220416004048.1514900-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9e14dbbd454581061c736bf70bf5cbb15ac927c upstream.
When resuming from system sleep state, restore_processor_state()
restores the boot CPU MSRs. These MSRs could be emulated by microcode.
If microcode is not loaded yet, writing to emulated MSRs leads to
unchecked MSR access error:
...
PM: Calling lapic_suspend+0x0/0x210
unchecked MSR access error: WRMSR to 0x10f (tried to write 0x0...0) at rIP: ... (native_write_msr)
Call Trace:
<TASK>
? restore_processor_state
x86_acpi_suspend_lowlevel
acpi_suspend_enter
suspend_devices_and_enter
pm_suspend.cold
state_store
kobj_attr_store
sysfs_kf_write
kernfs_fop_write_iter
new_sync_write
vfs_write
ksys_write
__x64_sys_write
do_syscall_64
entry_SYSCALL_64_after_hwframe
RIP: 0033:0x7fda13c260a7
To ensure microcode emulated MSRs are available for restoration, load
the microcode on the boot CPU before restoring these MSRs.
[ Pawan: write commit message and productize it. ]
Fixes: e2a1256b17b1 ("x86/speculation: Restore speculation related MSRs during S3 resume")
Reported-by: Kyle D. Pelton <kyle.d.pelton@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Tested-by: Kyle D. Pelton <kyle.d.pelton@intel.com>
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215841
Link: https://lore.kernel.org/r/4350dfbf785cd482d3fafa72b2b49c83102df3ce.1650386317.git.pawan.kumar.gupta@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c79865f3e8a2db93ec1e844509edfebe5a6ae56 upstream.
The GW71xx, GW72xx and GW73xx boards have USB1 routed to a USB OTG
connectors and USB2 routed to a USB hub.
The OTG connector has a over-currently protection with an active-low
pin and the USB1 to HUB connection has no over-current protection (as
the HUB itself implements this for its downstream ports).
Add proper dt nodes to specify the over-current pin polarity for USB1
and disable over-current protection for USB2.
Fixes: 6f30b27c5e ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits")
Cc: stable@vger.kernel.org
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f7ce6d7091765ed6c67c5d78aa364b9d17e3aab upstream.
Flexcom3 is used as board console serial. There are no pull-ups on these
lines on the board. This means that if a cable is not connected (that has
pull-ups included), stray characters could appear on the console as the
floating pins voltage levels are interpreted as incoming characters.
To avoid this problem, enable the internal pull-ups on these lines.
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220307113827.2419331-1-eugen.hristev@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50ff57888d0b13440e7f4cde05dc339ee8d0f1f8 upstream.
On a zoned filesystem, if we fail to allocate the root node for the log
root tree while syncing the log, we end up returning without finishing
the IO plug we started before, resulting in leaking resources as we
have started writeback for extent buffers of a log tree before. That
allocation failure, which typically is either -ENOMEM or -ENOSPC, is not
fatal and the fsync can safely fallback to a full transaction commit.
So release the IO plug if we fail to allocate the extent buffer for the
root of the log root tree when syncing the log on a zoned filesystem.
Fixes: 3ddebf27fc ("btrfs: zoned: reorder log node allocation on zoned filesystem")
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0f6cfb2bd165b0aa307750e07e03420859bd554 upstream.
Control Flow Integrity (CFI) instrumentation of the kernel noticed that
the caller, dev_attr_show(), and the callback, odvp_show(), did not have
matching function prototypes, which would cause a CFI exception to be
raised. Correct the prototype by using struct device_attribute instead
of struct kobj_attribute.
Reported-and-tested-by: Joao Moreira <joao@overdrivepizza.com>
Link: https://lore.kernel.org/lkml/067ce8bd4c3968054509831fa2347f4f@overdrivepizza.com/
Fixes: 006f006f1e ("thermal/int340x_thermal: Export OEM vendor variables")
Cc: 5.8+ <stable@vger.kernel.org> # 5.8+
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc45e55ebc58dbf622cb89ddbf797589c7a5510b upstream.
The "safe state" index is used by acpi_idle_enter_bm() to avoid
entering a C-state that may require bus mastering to be disabled
on entry in the cases when this is not going to happen. For this
reason, it should not be set to point to C3 type of C-states, because
they may require bus mastering to be disabled on entry in principle.
This was broken by commit d6b88ce2eb9d ("ACPI: processor idle: Allow
playing dead in C3 state") which inadvertently allowed the "safe
state" index to point to C3 type of C-states.
This results in a machine that won't boot past the point when it first
enters C3. Restore the correct behaviour (either demote to C1/C2, or
use C3 but also set ARB_DIS=1).
I hit this on a Fujitsu Siemens Lifebook S6010 (P3) machine.
Fixes: d6b88ce2eb9d ("ACPI: processor idle: Allow playing dead in C3 state")
Cc: 5.16+ <stable@vger.kernel.org> # 5.16+
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Woody Suwalski <wsuwalski@gmail.com>
[ rjw: Subject and changelog adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fd1fe4807f91ea0cca043114d929faa11bd4190 upstream.
I made a mistake with the commit a6aaa0032424 ("net: ethernet: stmmac:
fix altr_tse_pcs function when using a fixed-link"). I should have
tested against both scenario of having a SGMII interface and one
without.
Without the SGMII PCS TSE adpater, the sgmii_adapter_base address is
NULL, thus a write to this address will fail.
Cc: stable@vger.kernel.org
Fixes: a6aaa0032424 ("net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20220420152345.27415-1-dinguyen@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c05d8332f5d23fa3b521911cbe55a2b67fb21248 upstream.
We have now seen panel (XMG Core 15 e21 laptop) advertizing support
for Intel proprietary eDP backlight control via DPCD registers, but
actually working only with legacy pwm control.
This patch adds panel EDID check for possible HDR static metadata and
Intel proprietary eDP backlight control is used only if that exists.
Missing HDR static metadata is ignored if user specifically asks for
Intel proprietary eDP backlight control via enable_dpcd_backlight
parameter.
v2 :
- Ignore missing HDR static metadata if Intel proprietary eDP
backlight control is forced via i915.enable_dpcd_backlight
- Printout info message if panel is missing HDR static metadata and
support for Intel proprietary eDP backlight control is detected
Fixes: 4a8d79901d ("drm/i915/dp: Enable Intel's HDR backlight interface (only SDR for now)")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5284
Cc: Lyude Paul <lyude@redhat.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Filippo Falezza <filippo.falezza@outlook.it>
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220413082826.120634-1-jouni.hogander@intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
(cherry picked from commit b4b157577cb1de13bee8bebc3576f1de6799a921)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ddffdb9442a9d60b4a6e679ac48d7d21403a674 upstream.
The commit referenced below fixed packet re-routing if Netfilter mangles
a routing key property of a packet and the packet is routed in a VRF L3
domain. The fix, however, addressed IPv4 re-routing, only.
This commit applies the same behavior for IPv6. While at it, untangle
the nested ternary operator to make the code more readable.
Fixes: 6d8b49c3a3 ("netfilter: Update ip_route_me_harder to consider L3 domain")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba7542eb2dd5dfc75c457198b88986642e602065 upstream.
This patch fixes a memory corruption that occurred in the
nand_scan() path for Hynix nand device.
On boot, for Hynix nand device will panic at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual
address 00000070
| [00000070] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0
#38
| Hardware name: Generic DT based system
| PC is at nandc_set_reg+0x8/0x1c
| LR is at qcom_nandc_command+0x20c/0x5d0
| pc : [<c088b74c>] lr : [<c088d9c8>] psr: 00000113
| sp : c14adc50 ip : c14ee208 fp : c0cc970c
| r10: 000000a3 r9 : 00000000 r8 : 00000040
| r7 : c16f6a00 r6 : 00000090 r5 : 00000004 r4 :c14ee040
| r3 : 00000000 r2 : 0000000b r1 : 00000000 r0 :c14ee040
| Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Register r0 information: slab kmalloc-2k start c14ee000 pointer offset
64 size 2048
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| nandc_set_reg from qcom_nandc_command+0x20c/0x5d0
| qcom_nandc_command from nand_readid_op+0x198/0x1e8
| nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78
| hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454
| hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8
| nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0
| qcom_nandc_probe from platform_probe+0x58/0xac
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size.
This causes the sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_command() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page
size in qcom_nand_attach_chip call back after freeing the previously
allocated memory for bam txn as per nandc->max_cwperpage = 1 and then
again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on
page size in qcom_nand_attach_chip call back itself.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f1 ("mtd: rawnand: qcom: convert driver to nand_scan()")
Reported-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1650268107-5363-1-git-send-email-quic_mdalam@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31fa985b4196f8a66f027672e9bf2b81fea0417c upstream.
kasan_quarantine_remove_cache() is called in kmem_cache_shrink()/
destroy(). The kasan_quarantine_remove_cache() call is protected by
cpuslock in kmem_cache_destroy() to ensure serialization with
kasan_cpu_offline().
However the kasan_quarantine_remove_cache() call is not protected by
cpuslock in kmem_cache_shrink(). When a CPU is going offline and cache
shrink occurs at same time, the cpu_quarantine may be corrupted by
interrupt (per_cpu_remove_cache operation).
So add a cpu_quarantine offline flags check in per_cpu_remove_cache().
[akpm@linux-foundation.org: add comment, per Zqiang]
Link: https://lkml.kernel.org/r/20220414025925.2423818-1-qiang1.zhang@intel.com
Signed-off-by: Zqiang <qiang1.zhang@intel.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 694852ead287a3433126e7ebda397b242dc99624 upstream.
Ensure that the i_flags field of struct zonefs_inode_info is cleared to
0 when initializing a zone file inode, avoiding seeing the flag
ZONEFS_ZONE_OPEN being incorrectly set.
Fixes: b5c00e9757 ("zonefs: open/close zone on file open/close")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1da18a296f5ba4f99429e62a7cf4fdbefa598902 upstream.
The mount option "explicit_open" manages the device open zone
resources to ensure that if an application opens a sequential file for
writing, the file zone can always be written by explicitly opening
the zone and accounting for that state with the s_open_zones counter.
However, if some zones are already open when mounting, the device open
zone resource usage status will be larger than the initial s_open_zones
value of 0. Ensure that this inconsistency does not happen by closing
any sequential zone that is open when mounting.
Furthermore, with ZNS drives, closing an explicitly open zone that has
not been written will change the zone state to "closed", that is, the
zone will remain in an active state. Since this can then cause failures
of explicit open operations on other zones if the drive active zone
resources are exceeded, we need to make sure that the zone is not
active anymore by resetting it instead of closing it. To address this,
zonefs_zone_mgmt() is modified to change a REQ_OP_ZONE_CLOSE request
into a REQ_OP_ZONE_RESET for sequential zones that have not been
written.
Fixes: b5c00e9757 ("zonefs: open/close zone on file open/close")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20e582e16af24b074e583f9551fad557882a3c9d upstream.
This reverts commit bfe55a1f7fd6bfede16078bf04c6250fbca11588.
This was presumably misdiagnosed as an inability to use C3 at
all when I suspect the real problem is just misconfiguration of
C3 vs. ARB_DIS.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: 5.16+ <stable@vger.kernel.org> # 5.16+
Tested-by: Woody Suwalski <wsuwalski@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18d609daa546c919fd36b62a7b510c18de4b4af8 ]
Because mremap does not have a MAP_FIXED_NOREPLACE flag, it can destroy
existing mappings. This causes a segfault when regions such as text are
remapped and the permissions are changed.
Verify the requested mremap destination address does not overlap any
existing mappings by using mmap's MAP_FIXED_NOREPLACE flag. Keep
incrementing the destination address until a valid mapping is found or
fail the current test once the max address is reached.
Link: https://lkml.kernel.org/r/20220420215721.4868-2-sidhartha.kumar@oracle.com
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c85a9bae267f6b5e5e374d0d023bbbe9db096d3 ]
Avoid calling mmap with requested addresses that are less than the
system's mmap_min_addr. When run as root, mmap returns EACCES when
trying to map addresses < mmap_min_addr. This is not one of the error
codes for the condition to retry the mmap in the test.
Rather than arbitrarily retrying on EACCES, don't attempt an mmap until
addr > vm.mmap_min_addr.
Add a munmap call after an alignment check as the mappings are retained
after the retry and can reach the vm.max_map_count sysctl.
Link: https://lkml.kernel.org/r/20220420215721.4868-1-sidhartha.kumar@oracle.com
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb82c574691daf8f7fa9a160264d15c5804cb769 ]
The "read_bhrb" global symbol is only called under CONFIG_PPC64 of
arch/powerpc/perf/core-book3s.c but it is compiled for both 32 and 64 bit
anyway (and LLVM fails to link this on 32bit).
This fixes it by moving bhrb.o to obj64 targets.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220421025756.571995-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc6de2878429e85c1f1afaa566f7b5abb2243eef ]
There is a deadlock in rr_close(), which is shown below:
(Thread 1) | (Thread 2)
| rr_open()
rr_close() | add_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | rr_timer()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold rrpriv->lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need rrpriv->lock in position (2) of thread 2.
As a result, rr_close() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417125519.82618-1-duoming@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Brian Norris