SKL stage 1 patches still need polish so will likely miss the 3.18
merge window. We've decided to postpone to 3.19 so let's pull this in
to make patch merging and conflict handling easier.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Sink crc was implemented based on dp 1.1 spec that had all TEST_SINK bits
reserved reading all 0s. But when reviewing my latest changes on sink crc
Todd warned me that on new specs we have other valid bits on this reg that we
might want to preserve.
Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In some cases like when PSR just got enabled the panel need more vblank
times to calculate CRC. I figured that out with the new PSR test cases
facing some cases that I had a green screen but a blank CRC. Even with
2 vblank waits on kernel + 2 vblank waits on test case.
So let's give up to 6 vblank wait time. However we now check for
TEST_CRC_COUNT that shows when panel finished to calculate CRC and
has it ready.
v2: Jani pointed out attempts decrements was wrong and should never reach
the error condition. And Daniel pointed out that EIO is more appropriated than
EGAIN. Also I realized that I have to read test_crc_count after setting
test_sink
v3: Rebase and adding error message
Cc: Todd Previte <tprevite@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's make sure PSR is propperly disabled before to re-enabled it.
According to Spec, after disabled PSR CTL, the Idle state might occur
up to 24ms, that is one full frame time (1/refresh rate),
plus SRD exit training time (max of 6ms),
plus SRD aux channel handshake (max of 1.5ms).
So if something went wrong PSR will be disabled until next full
enable/disable setup.
v2: The 24ms above takes in account 16ms for refresh rate on 60Hz mode. However
on low frequency modes this can take longer. So let's use 50ms for safeness.
v3: Move wait out of psr.lock critical area.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The panel has to be reconfigured only when it really loose the power.
The traditional enable/disable sequence already take care of this so we can
minimize the time spend on every re-enable.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Skylake doesn't use the pre-charge field now, but, instead, we need to
specify the total number of SYNC pulses for the SYNC phase (pre-charge +
SYNC pattern pules). Let's use the default value (32) for that.
v3: increase DP AUX TX timeout as 400us is not to be used on SKL
apparently (Jesse).
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to provide a vfunc that will make the code in intel_dp_aux_ch()
loop once to start the AUX transaction. The return value (clock divider)
is unused on SKL, so just return 1.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we can apply the old aux_ctl = dp_ctl + 0x10 rule again.
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They are similar to Haswell.
v2: Rebased on top of drm-intel-nightly
v3: Rebased on top of Sonika's DP train defines renaming
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't need to setup everything else if it doesn't match all conditions.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
psr_enabled is already by itself a setup once so let's put the W/As there and
rename old setup once to setup_vsc.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If something while getting panel CRC this means that probably hw I/O error
so hw is busted and try again shouldn't help much.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDP panels are generally designed to support only a single clock and
lane configuration.
commit 56071a2076
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue May 6 14:56:52 2014 +0300
drm/i915: use lane count and link rate from VBT as minimums for eDP
should have started using the optimal link parameters for eDP
panels. Turns out a certain other OS uses DPCD instead of VBT, which
means trusting VBT on this may not be so reliable after all. Follow
suit.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81647
Tested-by: Adam Jirasek <libm3l@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79386
Tested-by: Narthana Epa <narthana.epa+freedesktop@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This goes back to
commit 06ea66b6bb
Author: Todd Previte <tprevite@gmail.com>
Date: Mon Jan 20 10:19:39 2014 -0700
drm/i915: Enable 5.4Ghz (HBR2) link rate for Displayport 1.2-capable devices
Cc: Todd Previte <tprevite@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Pimp commit message a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Oops, apparently intel_hdmi/intel_dp is the encoder - an object with a
distinct lifetime to the connector, and so we cannot simply reuse the
common function to unset and free the edid.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- final bits (again) for the rotation support (Sonika Jindal)
- support bl_power in the intel backlight (Jani)
- vdd handling improvements from Ville
- i830M fixes from Ville
- piles of prep work all over to make skl enabling just plug in (Damien, Sonika)
- rename DP training defines to reflect latest edp standards, this touches all
drm drivers supporting DP (Sonika Jindal)
- cache edids during single detect cycle to avoid re-reading it for e.g. audio,
from Chris
- move w/a for registers which are stored in the hw context to the context init
code (Arun&Damien)
- edp panel power sequencer fixes, helps chv a lot (Ville)
- piles of other chv fixes all over
- much more paranoid pageflip handling with stall detection and better recovery
from Chris
- small things all over, as usual
* tag 'drm-intel-next-2014-09-05' of git://anongit.freedesktop.org/drm-intel: (114 commits)
drm/i915: Update DRIVER_DATE to 20140905
drm/i915: Decouple the stuck pageflip on modeset
drm/i915: Check for a stalled page flip after each vblank
drm/i915: Introduce a for_each_plane() macro
drm/i915: Rewrite ABS_DIFF() in a safer manner
drm/i915: Add comments explaining the vdd on/off functions
drm/i915: Move DP port disable to post_disable for pch platforms
drm/i915: Enable DP port earlier
drm/i915: Turn on panel power before doing aux transfers
drm/i915: Be more careful when picking the initial power sequencer pipe
drm/i915: Reset power sequencer pipe tracking when disp2d is off
drm/i915: Track which port is using which pipe's power sequencer
drm/i915: Fix edp vdd locking
drm/i915: Reset the HEAD pointer for the ring after writing START
drm/i915: Fix unsafe vma iteration in i915_drop_caches
drm/i915: init sprites with univeral plane init function
drm/i915: Check of !HAS_PCH_SPLIT() in PCH transcoder funcs
drm/i915: Use HAS_GMCH_DISPLAY un underrun reporting code
drm/i915: Use IS_BROADWELL() instead of IS_GEN8() in forcewake code
drm/i915: Don't call gen8_fbc_sw_flush() on chv
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
drm: backmerge tag 'v3.17-rc5' into drm-next
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
Jani wanted some comments to explain why we call certain vdd on/off
functions in certain places.
v2: Make the comments more thorough (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to turn the DP port off after the pipe, otherwise the pipe won't
turn off properly on certain pch platforms at least (happens on my ILK for
example). This also matches the BSpec modeset sequence better. We still
don't match the spec exactly though (eg. audio disable should happen
much earlier), but at last this eliminates the nasty
wait_for_pipe_off() timeouts.
We already did the port disable after the pipe for VLV/CHV and for CPU
eDP.
For g4x leave the port disable where it is since that matches the
modeset sequence in the documentation and I don't have a suitable
machine to test if the other order would work.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec says we should enable the DP port before enabling panel power,
and that the port must be enabled with training pattern 1. Do so.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV the panel power sequencer may need to be "kicked" a bit to
lock onto the new port, and that needs to happen before any aux
transfers are attempted if we want the aux transfers to actaully
succeed. So turn on panel power (part of the "kick") before aux
transfers (DPMS_ON + link training).
This also matches the documented modeset sequence better for pch
platforms. The documentation doesn't explicitly state anything about the
DPMS or link training DPCD writes, but the panel power on step is
always listed before link training is mentioned.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=70117
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to make sure we find the power sequencer that the BIOS used
by first looking for one which has the panel power enabled, then
fall back to one with VDD force bit enabled, and finally look at
just the port select bits. This should make us pick the correct
power sequencer when the BIOS has already enabled the panel.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Shorten the vlv_intial_pps_pipe to make lines fit into 80
chars.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power sequencer loses its state when the disp2d power well is down.
Clear the dev_priv->pps_pipe tracking so that the power sequencer state
gets reinitialized the next time it's needed.
v2: Fix the pps_mutex vs. power_domain mutex deadlock by taking power
domain reference first
v3: Rename from edp_pps_(un)lock() to just pps_(un)lock() for the future,
update due to backlight code changes
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV/CHV have a per-pipe panel power sequencer which locks onto the
port once used. We need to keep track wich power sequencers are
locked to which ports.
v2: remove spurious whitespace change, rebase due to backlight changes (Imre)
Reviewed-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Break some really long lines to appease checkpatch a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce a new mutex (pps_mutex) to protect the power sequencer
state. For now this state includes want_panel_vdd as well as the
power sequencer registers.
We need a single mutex (as opposed to per port) because later on we
will need to deal with VLV/CHV which have multiple power sequencer
which can be reassigned to different ports.
v2: Add the locking to intel_dp_encoder_suspend too (Imre)
v3: Take care intel_edp_backlight_power() and
_intel_edp_backlight_on/off(), deal with reboot notifier
vlv_power_sequencer_pipe() call (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we may query the edid multiple times following a detect, record the
EDID found during output discovery and reuse it. This is a separate
issue from caching the output EDID across detection cycles.
v2: Implement connector->force() callback so that edid is associated
with the connector for user overrides as well (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both gmch and pch detection routines used the exact same routine for
eDP, so de-duplicate.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: : Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the defines to have levels instead of values for vswing and
pre-emph levels as the values may differ in other scenarios like low vswing of
eDP1.4 where the values are different.
Done using following cocci patch for each define:
@@
@@
# define DP_TRAIN_VOLTAGE_SWING_400 (0 << 0)
+ # define DP_TRAIN_VOLTAGE_SWING_LEVEL_0 (0 << 0)
...
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no need to use hex_dump_to_buffer() since we have a kernel helper to
dump up to 64 bytes just via printk(). In our case the actual size is 15 bytes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add cast since %*ph expects and int for the size parameter.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Renaming the HSW-specific macros for ddi buffer translation slot to denote the
slot and not the vswing/pre-emph values as they are platform-dependent.
This patch is based on top of the patch series for renaming the DP training
vswing/pre-emph defines:
http://lists.freedesktop.org/archives/intel-gfx/2014-August/050407.html
v2: Creating single macro with argument for slot number (Damien)
v3: Adding macro for num of translation entries (Damien)
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Less pointless indentation is always nice. There will be a bit more
code in this function once the power sequencer locking is fixed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we force vdd off warn if someone is still using it. With this
change the delayed vdd off work needs to check want_panel_vdd
itself to make sure it doesn't try to turn vdd off when someone
is using it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks nicer.
Not functional change.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add "No functional change" as requested by Jani.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a comment to explain why we care about the current want_panel_vdd
state in intel_dp_aux_ch().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
edp_* are now the lower level functions and intel_edp_* the higher level
ones. One should use them in pairs.
v2: Don't return void (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to use the higher level vdd on func here. Not a big deal
yet (we'd just get the warn when things go awry) but when the
locking gets fixed this becomes more important.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Passing the port as a parameter to PANEL_PORT_SELECT_VLV results in
neater code. Sadly the PCH port select bits aren't suitable for the
same treatment and the resulting macro would be much uglier, so
leave those defines as is.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris has decided that enough is enough. It's time to fixup dev Vs
dev_priv. This is a modest contribution to the crusade.
v2: Still use INTEL_INFO(), for the (mythical!) case we want to hardcode
the info struct with defines (Chris)
Rename the macro argument from 'dev' to 'dev_priv' (Jani)
v3: Use names unlikely to be used as macro arguments (Chris)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This lets the userspace switch off the backlight using the backlight
class sysfs bl_power file. The switch is done using the power sequencer;
the backlight PWM, and everything else, remains enabled. The display
backlight won't draw power, but for maximum power savings the encoder
needs to be switched off.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Tested_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make it possible to change panel power control backlight state without
touching the PWM. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Tested_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-08-22:
- basic code for execlist, which is the fancy new cmd submission on gen8. Still
disabled by default (Ben, Oscar Mateo, Thomas Daniel et al)
- remove the useless usage of console_lock for I915_FBDEV=n (Chris)
- clean up relations between ctx and ppgtt
- clean up ppgtt lifetime handling (Michel Thierry)
- various cursor code improvements from Ville
- execbuffer code cleanups and secure batch fixes (Chris)
- prep work for dev -> dev_priv transition (Chris)
- some of the prep patches for the seqno -> request object transition (Chris)
- various small improvements all over
* tag 'drm-intel-next-2014-09-01' of git://anongit.freedesktop.org/drm-intel: (86 commits)
drm/i915: fix suspend/resume for GENs w/o runtime PM support
drm/i915: Update DRIVER_DATE to 20140822
drm: fix plane rotation when restoring fbdev configuration
drm/i915/bdw: Disable execlists by default
drm/i915/bdw: Enable Logical Ring Contexts (hence, Execlists)
drm/i915/bdw: Document Logical Rings, LR contexts and Execlists
drm/i915/bdw: Print context state in debugfs
drm/i915/bdw: Display context backing obj & ringbuffer info in debugfs
drm/i915/bdw: Display execlists info in debugfs
drm/i915/bdw: Disable semaphores for Execlists
drm/i915/bdw: Make sure gpu reset still works with Execlists
drm/i915/bdw: Don't write PDP in the legacy way when using LRCs
drm/i915: Track cursor changes as frontbuffer tracking flushes
drm/i915/bdw: Help out the ctx switch interrupt handler
drm/i915/bdw: Avoid non-lite-restore preemptions
drm/i915/bdw: Handle context switch events
drm/i915/bdw: Two-stage execlist submit process
drm/i915/bdw: Write the tail pointer, LRC style
drm/i915/bdw: Implement context switching (somewhat)
drm/i915/bdw: Emission of requests with logical rings
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
In the HPD pulse handler we check for long pulses if the port is actually
connected, however we do that for IBX, but we use the pulse handling code on
GM45 systems as well, so we need to use a diffent check.
This patch refactors the digital port connected check out of the g4x detection
path and reuses it in the hpd pulse path.
Fixes: http://lkml.kernel.org/r/1409382202.5141.36.camel@marge.simpson.net
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
- Setting dp M2/N2 values plus state checker support (Vandana Kannan)
- chv power well support (Ville)
- DP training pattern 3 support for chv (Ville)
- cleanup of the hsw/bdw ddi pll code, prep work for skl (Damien)
- dsi video burst mode support (Shobhit)
- piles of other chv fixes all over (Ville et. al.)
- cleanup of the ddi translation tables setup code (Damien)
- 180 deg rotation support (Ville & Sonika Jindal)
* tag 'drm-intel-next-2014-08-08' of git://anongit.freedesktop.org/drm-intel: (59 commits)
drm/i915: Update DRIVER_DATE to 20140808
drm/i915: No busy-loop wait_for in the ring init code
drm/i915: Add sprite watermark programming for VLV and CHV
drm/i915: Round-up clock and limit drain latency
drm/i915: Generalize drain latency computation
drm/i915: Free pending page flip events at .preclose()
drm/i915: clean up PPGTT checking logic
drm/i915: Polish the chv cmnlane resrt macros
drm/i915: Hack to tie both common lanes together on chv
drm/i915: Add cherryview_update_wm()
drm/i915: Update DDL only for current CRTC
drm/i915: Parametrize VLV_DDL registers
drm/i915: Fill out the FWx watermark register defines
drm: Resetting rotation property
drm/i915: Add rotation property for sprites
drm: Add rotation_property to mode_config
drm/i915: Make intel_plane_restore() return an error
drm/i915: Add 180 degree sprite rotation support
drm/i915: Introduce a for_each_intel_encoder() macro
drm/i915: Demote the DRRS messages to debug messages
...
Atm we may retrain the DP link even if the CRTC is inactive through
HPD work->intel_dp_check_link_status(). This in turn can lock up the PHY
(at least on BYT), since the DP port is disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81948
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Atm we may leave eDP VDD enabled during system suspend after the CRTCs
are disabled through an HPD->DPCD read event. So disable VDD during
suspend at a point when no HPDs can occur.
Note that runtime suspend doesn't have the same problem, since there the
RPM ref held by VDD provides already the needed serialization.
v2:
- add note to commit message about the runtime suspend path (Ville)
- use edp_panel_vdd_off_sync(), so we can keep the WARN in
edp_panel_vdd_off() (Ville)
v3:
- rebased on -fixes (for_each_intel_encoder()->list_for_each_entry())
(Imre)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Cc: stable@vger.kernel.org (3.16+)
[Jani: fix sparse warning reported by Fengguang Wu]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville noticed that we can call ibx_digital_port_connected() which accesses
the HW without holding any power well/runtime pm reference. Fix this by
holding a display port power domain reference around the whole hpd_pulse
handler.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Don't print raw numbers, use port_name() and tell the user whether it's
long or short without having to figure out what the other magic number
means.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull intel drm fixes from Daniel Vetter:
"So I heard that proper pull requests have a revert on top ;-) So here
we go with my usual mid-merge-window pile of fixes.
[ Ed. This revert thing had better not become the "in" thing ]
Big fix is the duct-tape for ring init on g4x platforms, we seem to
have found the magic again to make those machines as happy as before
(not perfect though unfortunately, but that was never the case).
Otherwise fixes all over:
- tune down some overzealous debug output
- VDD power sequencing fix after resume
- bunch of dsi fixes for baytrail among them hw state checker
de-noising
- bunch of error state capture fixes for bdw
- misc tiny fixes/workarounds for various platforms
Last minute rebase was to kick out two patches that shouldn't have
been in here - they're for the state checker, so 0 functional code
affected.
Jani's back from vacation, so he'll take over -fixes from here"
* tag 'drm-intel-fixes-2014-08-08' of git://anongit.freedesktop.org/drm-intel: (21 commits)
Revert "drm/i915: Enable semaphores on BDW"
drm/i915: read HEAD register back in init_ring_common() to enforce ordering
drm/i915: Fix crash when failing to parse MIPI VBT
drm/i915: Bring GPU Freq to min while suspending.
drm/i915: Fix DEIER and GTIER collecting for BDW.
drm/i915: Don't accumulate hangcheck score on forward progress
drm/i915: Add the WaCsStallBeforeStateCacheInvalidate:bdw workaround.
drm/i915: Refactor Broadwell PIPE_CONTROL emission into a helper.
drm/i915: Fix threshold for choosing 32 vs. 64 precisions for VLV DDL values
drm/i915: Fix drain latency precision multipler for VLV
drm/i915: Collect gtier properly on HSW.
drm/i915: Tune down MCH_SSKPD values warning
drm/i915: Tune done rc6 enabling output
drm/i915: Don't require dev->struct_mutex in psr_match_conditions
drm/i915: Fix error state collecting
drm/i915: fix VDD state tracking after system resume
drm/i915: Add correct hw/sw config check for DSI encoder
drm/i915: factor out intel_edp_panel_vdd_sanitize
drm/i915: wait for all DSI FIFOs to be empty
drm/i915: work around warning in i915_gem_gtt
...
Daniel Vetter