The IDE PIO interface currently uses bdrv_read() to perform reads
synchronously. Synchronous I/O in the vcpu thread is bad because it
prevents the guest from executing code - it makes the guest
unresponsive.
This patch converts IDE PIO to use bdrv_aio_readv(). We simply need to
use the BUSY_STAT status so the guest knows to wait while we are busy.
The only external user of ide_sector_read() is restart behavior on I/O
errors and it is not affected by this change. We still need to restart
I/O in the same way.
Migration is also unaffected if I understand the code correctly. We
continue to use the same transfer function and the BUSY_STAT status
should never be migrated since we flush I/O before migrating device
state.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Tested-by: Richard Davies <richard@arachsys.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Allow the user to specify a disk's World Wide Name.
Linux guests can address disks by their unique World Wide Name number
(e.g. /dev/disk/by-id/wwn-0x5001517959123522). This patch adds support
for assigning a World Wide Name number to a virtual IDE disk.
Cc: kwolf@redhat.com
Signed-off-by: Floris Bos <dev@noc-ps.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Allow the user to override the default disk model name "QEMU HARDDISK".
Some Linux distributions use the /dev/disk/by-id/scsi-SATA_name-of-disk-
model_serial addressing scheme when refering to partitions in /etc/fstab
and elsewhere. This causes problems when starting a disk image taken from
an existing physical server under qemu, because when running under qemu
name-of-disk-model is always "QEMU HARDDISK".
This patch introduces a model=s option which in combination with the
existing serial=s option can be used to fake the disk the operating
system was previously on, allowing the OS to boot properly.
Cc: kwolf@redhat.com
Signed-off-by: Floris Bos <dev@noc-ps.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The definitions in ide/internal.h are duplicates, since ATAPI commands
actually come from SCSI. Use the ones in scsi-defs.h and move the
missing ones there. Two exceptions:
- MODE_PAGE_WRITE_PARMS conflicts with the "flexible disk geometry"
page in scsi-disk.c. It is unused, so pick the latter.
- GPCMD_* is left in ide/internal.h, at least for now.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Today, when notifying a VM state change with vm_state_notify(),
we pass a VMSTOP macro as the 'reason' argument. This is not ideal
because the VMSTOP macros tell why qemu stopped and not exactly
what the current VM state is.
One example to demonstrate this problem is that vm_start() calls
vm_state_notify() with reason=0, which turns out to be VMSTOP_USER.
This commit fixes that by replacing the VMSTOP macros with a proper
state type called RunState.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
It's convenience stuff for block device models, so block.h isn't the
ideal home either, but better than block_int.h.
Permits moving some #include "block_int.h" from device model .h into
.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already track it in BlockDriverState. Just like tray open/close
state, we should track it in the device models instead, because it's
device state.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already track it in BlockDriverState since commit 4be9762a. As
discussed in that commit's message, we should track it in the device
device models instead, because it's device state.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drop WIN_SRST, it has the same value as WIN_DEVICE_RESET.
Drop unused WIN_RESTORE, it has the same value as WIN_RECAL.
Drop codes that are not implemented and long obsolete: WIN_READ_LONG,
WIN_READ_LONG_ONCE, WIN_WRITE_LONG, WIN_WRITE_LONG_ONCE, WIN_FORMAT
(all obsolete since ATA4), WIN_ACKMEDIACHANGE, WIN_POSTBOOT,
WIN_PREBOOT (obsolete since ATA3), WIN_WRITE_SAME (obsolete since
ATA3, code reused for something else in ACS2), WIN_IDENTIFY_DMA
(obsolete since ATA4).
Drop codes that are not implemented and vendor-specific:
EXABYTE_ENABLE_NEST, DISABLE_SEAGATE.
Drop WIN_INIT, it isn't implemented, its value used to be reserved,
and is used for something else since ATA8.
CFA_IDLEIMMEDIATE isn't specific to CFATA. ACS-2 shows it as a
defined command in ATA-1, -2 and -3. Rename to WIN_IDLEIMMEDIATE2.
Mark vendor specific, retired, and obsolete codes.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Decouple the I/O accounting from bdrv_aio_readv/writev/flush and
make the hardware models call directly into the accounting helpers.
This means:
- we do not count internal requests from image formats in addition
to guest originating I/O
- we do not double count I/O ops if the device model handles it
chunk wise
- we only account I/O once it actuall is done
- can extent I/O accounting to synchronous or coroutine I/O easily
- implement I/O latency tracking easily (see the next patch)
I've conveted the existing device model callers to the new model,
device models that are using synchronous I/O and weren't accounted
before haven't been updated yet. Also scsi hasn't been converted
to the end-to-end accounting as I want to defer that after the pending
scsi layer overhaul.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add support for TRIM sub function of the data set management command,
and wire it up to the qemu discard infrastructure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Replace the is_read flag with a dma_cmd flag to allow the dma and
restart logic to handler other commands like TRIM.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When adding the werror=stop mode, some flags were added to s->status
which are used to determine what kind of operation should be restarted
when the VM is continued.
Unfortunately, it turns out that s->status is in fact a device register
and as such is visible to the guest (some of the abused bits are even
writable for the guest).
For migration we keep on using the old VMState field (renamed to
migration_compat_status) if the status register doesn't use any of the
previously abused bits. If it does, we use a subsection with a clean copy of
the status register.
The error status is always sent in a subsection if there is any error. It can't
use the old field because errors happen even without PCI.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
An "ide-drive" is either a hard disk or a CD-ROM, depending on the
associated BlockDriverState's type hint. Unclean; disk vs. CD belongs
to the guest part, not the host part.
Have separate qdevs "ide-hd" and "ide-cd" to model disk vs. CD in
the guest part.
Keep ide-drive for backward compatibility.
"ide-disk" would perhaps be a nicer name than "ide-hd", but there's
already "scsi-disk", which is like "ide-drive", and will be likewise
split in the next commit. {ide,scsi}-{hd,cd} is the best consistent
set of names I could find within the backward compatibility
straightjacket.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Besides moving code, this patch only fixes some whitespace issues in the moved
code and makes all functions in atapi.c static which can be static.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Implement the 'media' sub-command of the GET_EVENT_STATUS_NOTIFICATION
command. This helps us report tray open, tray closed, no media, media
present states to the guest.
Newer Linux kernels (2.6.38+) rely on this command to revalidate discs
after media change.
This patch also sends out tray open/closed status to the guest driver
when requested e.g. via the CDROM_DRIVE_STATUS ioctl (thanks Markus).
Without such notification, the guest and qemu's tray open/close status
was frequently out of sync, causing installers like Anaconda detecting
no disc instead of tray open, confusing them terribly.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Factor the DMA I/O path that is duplicated between read and write
commands, into common helpers using the s->is_read flag added for
the macio ATA controller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I modified ide_identify() to include the zero-based queue length
value in word 75, and set bit 8 in word 76 to signal NCQ support
in the identify data for AHCI SATA drives.
Signed-off-by: Roland Elek <elek.roland@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The ATA core is currently heavily intertwined with BMDMA code. Let's loosen
that a bit, so we can happily replace the DMA backend with different
implementations.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The ATA command interpretation code can be used for PATA and SATA
interfaces alike. So let's split it out into a separate function.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of always assuming success for bdrv_aio_flush, actually do something
with the error. This respects the werror option and accordingly ignores the
error, reports it to the guest or stops the VM and retries after cont.
Ignoring the error is trivial, obviously. For stopping the VM and retrying
later old code can be reused, but we need to introduce a new status for "retry
a flush". For reporting to the guest, fortunately the same action is required
as for a failed read/write (status = DRDY | ERR, error = ABRT), so this code
can be reused as well.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This reverts commit ed487bb1d6.
The conflicts are due to commit 4fc8d6711a
that is a fix to the ide_drive_pre_save() function. It reverts both
(and both are reinstantiated later in the series)
Conflicts:
hw/ide/core.c
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It still always succeeds. The next commits will add failures.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The two aren't independent variables. Make that obvious.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make the property point to BlockDriverState, cutting out the DriveInfo
middleman. This prepares the ground for block devices that don't have
a DriveInfo.
Currently all user-defined ones have a DriveInfo, because the only way
to define one is -drive & friends (they go through drive_init()).
DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device. I'm
working towards a new way to define block devices, with clean
host/guest separation, and I need to get DriveInfo out of the way for
that.
Fortunately, the device models are perfectly happy with
BlockDriverState, except for two places: ide_drive_initfn() and
scsi_disk_initfn() need to check the DriveInfo for a serial number set
with legacy -drive serial=... Use drive_get_by_blockdev() there.
Device model code should now use DriveInfo only when explicitly
dealing with drives defined the old way, i.e. without -device.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It needs to be a qdev property, because it belongs to the drive's
guest part.
Bonus: info qtree now shows the serial number.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 428c149b added IDEState member conf to let commit 0009baf1 find
the BlockConf from there. It exists only for qdev drives, created via
ide_drive_initfn(), not for drives created via ide_init2().
But for a qdev drive, we can just as well reach its IDEDevice, which
contains the BlockConf. Do that, and revert the parts of commit
428c149b that add IDEState member conf.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of doing tricks to get the pci_dev, just pass it in the 1st
place. Patch is a bit longer that reverting the pci_dev field, but it
states more clearly (IMHO) what we are doing.
It also fixes the bm test, now that you told me that ->unit is not
always valid.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Save/restore information necessary to continue in progress PIO/ATAPI CMD
transfers.
This includes the IO buffer.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add three new qdev properties to export block topology information to
the guest. This is needed to get optimal I/O alignment for RAID arrays
or SSDs.
The options are:
- physical_block_size to specify the physical block size of the device,
this is going to increase from 512 bytes to 4096 kilobytes for many
modern storage devices
- min_io_size to specify the minimal I/O size without performance impact,
this is typically set to the RAID chunk size for arrays.
- opt_io_size to specify the optimal sustained I/O size, this is
typically the RAID stripe width for arrays.
I decided to not auto-probe these values from blkid which might easily
be possible as I don't know how to deal with these issues on migration.
Note that we specificly only set the physical_block_size, and not the
logial one which is the unit all I/O is described in. The reason for
that is that IDE does not support increasing the logical block size and
at last for now I want to stick to one meachnisms in queue and allow
for easy switching of transports for a given backing image which would
not be possible if scsi and virtio use real 4k sectors, while ide only
uses the physical block exponent.
To make this more common for the different block drivers introduce a
new BlockConf structure holding all common block properties and a
DEFINE_BLOCK_PROPERTIES macro to add them all together, mirroring
what is done for network drivers. Also switch over all block drivers
to use it, except for the floppy driver which has weird driveA/driveB
properties and probably won't require any advanced block options ever.
Example usage for a virtio device with 4k physical block size and
8k optimal I/O size:
-drive file=scratch.img,media=disk,cache=none,id=scratch \
-device virtio-blk-pci,drive=scratch,physical_block_size=4096,opt_io_size=8192
aliguori: updated patch to take into account BLOCK events
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds a new property named 'ver' to ide-drive which allows to
specify the version which the virtual disk/cdrom should report to the
guest. By default this is the qemu version (i.e. 0.12). usage:
-drive if=none,id=disk,file=...
-device ide-drive,bus=ide.0,unit=0,drive=disk,ver=42
You can also switch the version for all ide drives using:
-global ide-drive.ver=42
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This is a workaround only, and is a partial revert
of a few changes to BMDMAState which removed pci_dev
field on the way.
- cmd646 pci_from_bm() expects bm->unit value to
correspond with bm data being passed to callback
as opaque pointer. This breaks when write to dma
control register of second channel happens when no
dma operation is in progress, so bm->unit is zero
for second channel, and pci_from_bm() returns garbage
pointer. Crash happens shortly after that while
dereferencing that pointer.
v0->v1: cleaned up dead code from pci_from_bm.
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Problem: x86 systems could not survive a few system_resets.
Clear most of IDE state when reset. Implement the missing reset handlers.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
It is used everywhere as uint8_t except in one place. Cast to uint16_t
in that place
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This allows the ide bus being initialized without drives attached
and the drives being attached and initialization later on as
separate step.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Stefan Hajnoczi