This patch implements initial vmstate creation or loading at the start
of record/replay. It is needed for rewinding the execution in the replay mode.
v4 changes:
- snapshots are not created by default anymore
v3 changes:
- added rrsnapshot option
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170124071746.4572.61449.stgit@PASHA-ISP>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch introduces save_vmstate function to allow saving and loading
vmstates from the replay module.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170124071741.4572.13714.stgit@PASHA-ISP>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For configurations of the pflash_cfi01 device which set it up with a
device-width not equal to the width (ie where we are emulating
multiple narrow flash devices wired up in parallel), we were giving
incorrect values in the CFI data table:
(1) the sector length entry should specify the sector length for a
single device, not the length for the overall collection of
devices
(2) the number of blocks per device must not be divided by the
number of devices because the resulting device size would not
match the overall size
(3) this then means that the overall write block size must be
modified depending on the number of devices because the entry is
per device and when the guest writes into the flash it
calculates the write size by using the CFI entry (write size
per device) multiplied by the number of chips.
(It would alternatively be possible to modify the write
block size in the CFI table (currently hardcoded at 2048) and
leave the overall write block size alone.)
This commit corrects these bugs, and adds a hw-compat property
to retain the old behaviour on 2.8 and earlier versions. (The
only board we have which uses this sort of flash config and
has machine versioning is the "virt" board -- the PC uses a
single flash device and so behaviour is unaffected whether
using old-multiple-chip-handling or not.)
Here is a configuration example from the vexpress board:
VEXPRESS_FLASH_SIZE = 64M
VEXPRESS_FLASH_SECT_SIZE 256K
num-blocks = VEXPRESS_FLASH_SIZE / VEXPRESS_FLASH_SECT_SIZE = 256
sector-length = 256K
width = 4
device-width = 2
The code will fill the CFI entry with the following entries:
num-blocks = 256
sector-length = 128K
writeblock_size = 2048
This results in two chips, each with 256 * 128K = 32M device size and
a write block size of 2048.
A sector erase will be sent to both chips, thus 256K must be erased.
When the guest sends a block write command, it will write 4096 bytes
data at once (2048 per device).
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: cleaned up and expanded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/register.h provides macros like FIELD which make it easy to define
shift, mask and length constants for the fields within a register.
Unfortunately register.h also includes a lot of other things, some
of which will only compile in the softmmu build.
Pull the FIELD macro and friends out into a separate header file,
so they can be used in places like target/arm files which also
get built in the user-only configs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-5-git-send-email-peter.maydell@linaro.org
Bitmaps with a granularity of 58 or above can be neither serialized nor
deserialized (see the comment in the function added in this series for
an explanation). This patch adds a function so that we can check whether
a bitmap actually can be (de-)serialized at all, thus avoiding failing
the necessary assertion in hbitmap_serialization_granularity().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20161115225746.3590-2-mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Add remaining bits of the Altera NiosII R1 support into qemu, which
is documentation, MAINTAINERS file entry, configure bits, arch_init
and configuration files for both linux-user (userland binaries) and
softmmu (hardware emulation).
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-8-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Add missing bits for qemu-user required for emulating Altera Nios2
userspace binaries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-4-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Add nios2 disassembler support. This patch is composed from binutils files
from commit "Opcodes and assembler support for Nios II R2". The files from
binutils used in this patch are:
include/opcode/nios2.h
include/opcode/nios2r1.h
include/opcode/nios2r2.h
opcodes/nios2-opc.c
opcodes/nios2-dis.c
Checkpatch says total: 114 errors, 0 warnings, 3609 lines checked , which
is caused by a different coding style in those files. These warnings and
errors are not addressed To let these files be easily synchronized between
binutils and qemu.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-2-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
A fix has been committed in upstream glib commit
210a9796f78eb90f76f1bd6a304e9fea05e97617.
(See also related bug https://bugzilla.gnome.org/show_bug.cgi?id=764415)
It is desirable to use the glib version instead of qemu copy, since it
provides more debugging facilities (G_MAIN_POLL_DEBUG etc), and
hopefully has a better maintainance. Hopefully, we can drop the qemu
copy in a few years.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
There is no need to have those functions as public API.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add also a missing parenthesis in a comment.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The vmstate_pci_device and vmstate_pcie_devices differ
just in the size of one buffer; combine the two using a _TEST
macro.
I think this is safe as long as everywhere which currently
uses either of these two uses the right type.
One thing that concerns me is that some places use pci_device_load/save
which does some irq mangling, but others just use the VMSTATE_PCI_DEVICE
macro - how are they getting the same irq mangling?
This passes a smoke test migrate of:
./x86_64-softmmu/qemu-system-x86_64 -M pc,accel=kvm -m 1024
./littlefed20.img -device e1000e -device virtio-net -device
e1000 -device virtio-rng -device megasas -device megasas-gen2 -device
ioh3420 -device nec-usb-xhci
to an unmodified qemu.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20161214195829.18241-1-dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
commit fe904ea824 fixed a case
which migration aborted QEMU because it didn't regain the control
of images while some errors happened.
Actually, there are another two cases can trigger the same error reports:
" bdrv_co_do_pwritev: Assertion `!(bs->open_flags & 0x0800)' failed",
Case 1, codes path:
migration_thread()
migration_completion()
bdrv_inactivate_all() ----------------> inactivate images
qemu_savevm_state_complete_precopy()
socket_writev_buffer() --------> error because destination fails
qemu_fflush() ----------------> set error on migration stream
-> qmp_migrate_cancel() ----------------> user cancelled migration concurrently
-> migrate_set_state() ------------------> set migrate CANCELLIN
migration_completion() -----------------> go on to fail_invalidate
if (s->state == MIGRATION_STATUS_ACTIVE) -> Jump this branch
Case 2, codes path:
migration_thread()
migration_completion()
bdrv_inactivate_all() ----------------> inactivate images
migreation_completion() finished
-> qmp_migrate_cancel() ---------------> user cancelled migration concurrently
qemu_mutex_lock_iothread();
qemu_bh_schedule (s->cleanup_bh);
As we can see from above, qmp_migrate_cancel can slip in whenever
migration_thread does not hold the global lock. If this happens after
bdrv_inactive_all() been called, the above error reports will appear.
To prevent this, we can call bdrv_invalidate_cache_all() in qmp_migrate_cancel()
directly if we find images become inactive.
Besides, bdrv_invalidate_cache_all() in migration_completion() doesn't have the
protection of big lock, fix it by add the missing qemu_mutex_lock_iothread();
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Message-Id: <1485244792-11248-1-git-send-email-zhang.zhanghailiang@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
migrate_add_blocker should rightly fail if the '--only-migratable'
option was specified and the device in use should not be able to
perform the action which results in an unmigratable VM.
Make migrate_add_blocker return -EACCES in this case.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1484566314-3987-6-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
If a migration is already in progress and somebody attempts
to add a migration blocker, this should rightly fail.
Add an errp parameter and a retcode return value to migrate_add_blocker.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1484566314-3987-5-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Merged with recent 'Allow invtsc migration' change
Add a new option "--only-migratable" in qemu which will allow to add
only those devices which will not fail qemu after migration. Devices
set with the flag 'unmigratable' cannot be added when this option will
be used.
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1484566314-3987-3-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Currently we cannot directly transfer a QTAILQ instance because of the
limitation in the migration code. Here we introduce an approach to
transfer such structures. We created VMStateInfo vmstate_info_qtailq
for QTAILQ. Similar VMStateInfo can be created for other data structures
such as list.
When a QTAILQ is migrated from source to target, it is appended to the
corresponding QTAILQ structure, which is assumed to have been properly
initialized.
This approach will be used to transfer pending_events and ccs_list in spapr
state.
We also create some macros in qemu/queue.h to access a QTAILQ using pointer
arithmetic. This ensures that we do not depend on the implementation
details about QTAILQ in the migration code.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-3-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Current migration code cannot handle some data structures such as
QTAILQ in qemu/queue.h. Here we extend the signatures of put/get
in VMStateInfo so that customized handling is supported. put now
will return int type.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-2-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
make sure that external callers won't try to modify
possible_cpus and owner of possible_cpus can access
it directly when it modifies it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1484759609-264075-5-git-send-email-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The existing default_config_files table in arch_init.c has a
single entry, making it completely unnecessary. The whole code
can be replaced by a single qemu_read_config_file() call in vl.c.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170117180051.11958-1-ehabkost@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently DNS resolution is done automatically as part
of the creation of a QIOChannelSocket object instance.
This works ok for network clients where you just end
up a single network socket, but for servers, the results
of DNS resolution may require creation of multiple
sockets.
Introducing a DNS resolver API allows DNS resolution
to be separated from the socket object creation. This
will make it practical to create multiple QIOChannelSocket
instances for servers.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Now that task objects have a directly associated error,
there's no need for an an Error **errp parameter to
the QIOTask thread worker function. It already has a
QIOTask object, so can directly set the error on it.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Currently the QIOTaskFunc signature takes an Object * for
the source, and an Error * for any error. We also need to
be able to provide a result pointer. Rather than continue
to add parameters to QIOTaskFunc, remove the existing
ones and simply pass the QIOTask object instead. This
has methods to access all the other data items required
in the callback impl.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Currently when a task fails, the error is never explicitly
associated with the task object, it is just passed along
through the completion callback. This adds the ability to
explicitly associate an error with the task.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Currently there is no data associated with a successful
task completion. This adds an opaque pointer to the task
to store an arbitrary result.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The GDestroyNotify parameter is already a pointer, so does
not need a '*' suffix on the type.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Incrementing the reference in qio_task_get_source is
not necessary, since we're not running concurrently
with any other code touching the QIOTask. This
minimizes chances of further memory leaks.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
- rework of the zpci code, giving us proper multibus support
- introduction of the 2.9 machine
- fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fzmu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20170120-v2' into staging
First set of s390x patches for 2.9:
- rework of the zpci code, giving us proper multibus support
- introduction of the 2.9 machine
- fixes and improvements
# gpg: Signature made Fri 20 Jan 2017 09:11:58 GMT
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20170120-v2:
virtio-ccw: fix ring sizing
s390x/pci: merge msix init functions
s390x/pci: handle PCIBridge bus number
s390x/pci: use hashtable to look up zpci via fh
s390x/pci: PCI multibus bridge handling
s390x/pci: optimize calling s390_get_phb()
s390x/pci: change the device array to a list
s390x/pci: dynamically allocate iommu
s390x/pci: make S390PCIIOMMU inherit Object
s390x/kvm: use kvm_gsi_routing_enabled in flic
s390x: add compat machine for 2.9
s390x: remove double compat statement
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Version: GnuPG v1
iQEcBAABAgAGBQJYgXzxAAoJEO8Ells5jWIRgtAIAKuFrOBE/xJnjd/45sVKcx2j
fsohKHF8T/eLmt5sw+MhGtnM/oRJRUX8kGpA9AU8m6TCSaTYh2tOKX5lwrykuAzk
feqz2pqZFwiLWs5Ro7qEQIhMkqtFetODvKd05qnKnAldj8SC45czKxdghmSP/B+w
4nnDEdqVqUuUseDCa1mW1b4f6g1N93LbgChK7lK9Xqg+OqeEbQ7nLgVvcWvN7+Ea
DfDKWP8tjQ5QhjzFWc4wa9/Tx+0HI7Dn57fv98XdJMvm1kt/MdnO7QKAXWmHH5s/
6DX+NHgN0ZAn85gv/ufq1F9C4TstbAoZA9EOGhoBJ5ww8mueARB3L2iCj+OcS9A=
=gkbh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Fri 20 Jan 2017 02:58:57 GMT
# gpg: using RSA key 0xEF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
tap: fix memory leak on failure in net_init_tap()
hw/pci: use-after-free in pci_nic_init_nofail when nic device fails to initialize
hw/net/dp8393x: Avoid unintentional sign extensions on addresses
m68k: QOMify the MCF Fast Ethernet Controller device
net: optimize checksum computation
docs: Fix description of the sentence
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
writeable fw cfg blobs which will be used for guest to host
communication
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYgSq0AAoJECgfDbjSjVRpHtwH/j/viN38ginAvuRiPssEiitb
VC3oO09siMx+rO97H7ur5cVcwiyMFxG90Dtmsptf3r46hzgUcv4meC4zzNG3Xds6
Iwsqy1m3nQDEL1dbU7XbhfbrWAGCiY1I+O2JRSvHQ8+HsmP6vOLxPPEQTlFRQIrk
k9HHlMHo2tYU0hhSOOoDDG/mBG8QcYgIaGleCMrVBlV/Q6w7lnD8XVgPWjEF5RsG
2SkbY+JQJlmt6qZpkbdQKox4cHFxlA8f6P9ne1o++gjVENhbe6KrDFhROE560Lbn
dtypZV6Y0Pt6SMrk+lR2Gd2DHI/10LhNVi/mz6o1HrCzmISJlIxIvXD6XmhqdPk=
=7hNY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, vhost, pc: fixes, features
writeable fw cfg blobs which will be used for guest to host
communication
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 19 Jan 2017 21:08:04 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio: force VIRTIO_F_IOMMU_PLATFORM
virtio: fix up max size checks
vhost: drop VHOST_F_DEVICE_IOTLB
update-linux-headers.sh: support __bitwise
virtio_crypto: header update
pci_regs: update to latest linux
virtio-mmio: switch to linux headers
virtio_mmio: add standard header file
virtio: drop an obsolete comment
fw-cfg: bump "x-file-slots" to 0x20 for 2.9+ machine types
pc: Add 2.9 machine-types
fw-cfg: turn FW_CFG_FILE_SLOTS into a device property
fw-cfg: support writeable blobs
vhost_net: device IOTLB support
virtio: disable notifications again after poll succeeded
Revert "virtio: turn vq->notification into a nested counter"
virtio-net: enable ioeventfd even if vhost=off
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As noticed by David Gilbert, commit 6053a86 'kvmclock: reduce kvmclock
differences on migration' added 'x-mach-use-reliable-get-clock' and a
compatibility entry that turns it off; however it got merged after 2.8.0
was released but the entry has gone into PC_COMPAT_2_7 where it should
have gone into PC_COMPAT_2_8.
Fix it by moving the entry to PC_COMPAT_2_8.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170118175343.GA26873@amt.cnet>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a board level property to the virt board which will
enable EL2 on the CPU if the user asks for it. The
default is not to provide EL2. If EL2 is enabled then
we will use SMC as our PSCI conduit, and report the
virtualization support in the GICv3 device tree node
and the ACPI tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-19-git-send-email-peter.maydell@linaro.org
If we are giving the guest a CPU with EL2, it is likely to
want to use the HVC instruction itself, for instance for
providing PSCI to inner guest VMs. This makes using HVC
as the PSCI conduit for the outer QEMU a bad idea. We will
want to use SMC instead is this case: this makes sense
because QEMU's PSCI implementation is effectively an
emulation of functionality provided by EL3 firmware.
Add code to support selecting the PSCI conduit to use,
rather than hardcoding use of HVC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1483977924-14522-15-git-send-email-peter.maydell@linaro.org
Implement the function which signals virtual interrupts to the
CPU as appropriate following CPU interface state changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-13-git-send-email-peter.maydell@linaro.org
As the first step in adding support for the virtualization
extensions to the GICv3 emulation:
* add the necessary data fields to the state structures
* add the fields to the migration state, as a subsection
which is only present if virtualization is enabled
The use of a subsection means we retain migration
compatibility as EL2 is not enabled on any CPUs currently.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-8-git-send-email-peter.maydell@linaro.org
Wire the new VIRQ, VFIQ and maintenance interrupt lines from the
GIC to each CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-5-git-send-email-peter.maydell@linaro.org
Augment the GIC's QOM device interface by adding two
new sets of sysbus IRQ lines, to signal VIRQ and VFIQ to
each CPU.
We never use these, but it's helpful to keep the v2-and-earlier
GIC's external interface in line with that of the GICv3 to
avoid board code having to add extra code conditional on which
version of the GIC is in use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-3-git-send-email-peter.maydell@linaro.org
Augment the GICv3's QOM device interface by adding two
new sets of sysbus IRQ lines, to signal VIRQ and VFIQ to
each CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-2-git-send-email-peter.maydell@linaro.org
The Aspeed SMC controllers have a mode (Command mode) in which
accesses to the flash content are no different than doing MMIOs. The
controller generates all the necessary commands to load (or store)
data in memory.
However, accesses are restricted to the segment window assigned the
the flash module by the controller. This window is defined by the
Segment Address Register.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-8-git-send-email-clg@kaod.org
[PMM: Deleted now-unused aspeed_smc_is_usermode() function]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SPI controller of the AST2400 SoC has less registers. So we can
adjust the size of the memory region holding the registers depending
on the controller type. We can also remove the guest_error logging
which is useless as the range of the region is strict enough.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1483979087-32663-7-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is getting difficult to read. Also add a 'has_dma' field for each
controller type.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-6-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current code seems to assume ring size is
always decreased but this is not required by spec:
what spec says is just that size can not exceed
the maximum. Fix it up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <1484256243-1982-1-git-send-email-mst@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When running qemu-system-m68k with the "-net" parameter (for example
simply "-net nic -net user"), there is currently a confusing warning
message saying:
Warning: requested NIC (anonymous, model mcf_fec) was not created
(not supported by this machine?)
This seems to happen because the MCF NIC has never been adapted to
the currently expected QEMU device behavior. Thus let's QOMify the
NIC now to get rid of the warning message.
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Use the Intel HAX is kernel-based hardware acceleration module for
Windows (similar to KVM on Linux).
Based on the "target/i386: Add Intel HAX to android emulator" patch
from David Chou <david.j.chou@intel.com>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <7b9cae28a0c379ab459c7a8545c9a39762bd394f.1484045952.git.vpalatin@chromium.org>
[Drop hax_populate_ram stub. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
That's a forward port of the core HAX interface code from the
emu-2.2-release branch in the external/qemu-android repository as used by
the Android emulator.
The original commit was "target/i386: Add Intel HAX to android emulator"
saying:
"""
Backport of 2b3098ff27bab079caab9b46b58546b5036f5c0c
from studio-1.4-dev into emu-master-dev
Intel HAX (harware acceleration) will enhance android emulator performance
in Windows and Mac OS X in the systems powered by Intel processors with
"Intel Hardware Accelerated Execution Manager" package installed when
user runs android emulator with Intel target.
Signed-off-by: David Chou <david.j.chou@intel.com>
"""
It has been modified to build and run along with the current code base.
The formatting has been fixed to go through scripts/checkpatch.pl,
and the DPRINTF macros have been updated to get the instanciations checked by
the compiler.
The FPU registers saving/restoring has been updated to match the current
QEMU registers layout.
The implementation has been simplified by doing the following modifications:
- removing the code for supporting the hardware without Unrestricted Guest (UG)
mode (including all the code to fallback on TCG emulation).
- not including the Darwin support (which is not yet debugged/tested).
- simplifying the initialization by removing the leftovers from the Android
specific code, then trimming down the remaining logic.
- removing the unused MemoryListener callbacks.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <e1023837f8d0e4c470f6c4a3bf643971b2bca5be.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the generic cpu_synchronize_ functions to the common hw_accel.h header,
in order to prepare for the addition of a second hardware accelerator.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <f5c3cffe8d520011df1c2e5437bb814989b48332.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
C11 allows errno to be clobbered by pretty much any library function
call, so in general callers need to take care to save errno before
calling other functions.
However, for error reporting functions this is rather awkward and can
make the code on the caller side more complicated than
necessary. error_setg_errno() already takes care of preserving errno
and some functions rely on that, so just promise that we continue to
do so in the future.
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Message-Id: <1469611466-31574-1-git-send-email-silbe@linux.vnet.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Update header from latest linux driver. Session creation structs gain
padding to make them same size. Formatting cleanups.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
More precisely, the "x-file-slots" count is bumped for all machine types
that:
(a) use fw_cfg, and
(b) are not versioned (hence migration is not expected to work for them
across QEMU releases anyway), or have version 2.9.
This affects machine types implemented in the following source files:
- "hw/arm/virt.c". The "virt-*" machine type is versioned, and the <= 2.8
versions already depend on HW_COMPAT_2_8 (see commit e353aac51b).
Therefore adding the "x-file-slots" compat values to HW_COMPAT_2_8
suffices.
- "hw/i386/pc.c". The "pc-i440fx-*" (including "pc-*") and "pc-q35-*"
machine types are versioned. Modifying HW_COMPAT_2_8 is sufficient here
too (see commit "pc: Add 2.9 machine-types"). The "isapc" machtype is
not versioned. The "xenfv" machine type, which uses fw_cfg for direct
kernel booting, is also not versioned.
- "hw/ppc/mac_newworld.c". The "mac99" machine type is not versioned.
- "hw/ppc/mac_oldworld.c". The "g3beige" machine type is not versioned.
- "hw/sparc/sun4m.c". None of the 9 machine types defined in this file
appear versioned.
- "hw/sparc64/sun4u.c". None of the 3 machine types defined in this file
appear versioned.
Cc: "Gabriel L. Somlo" <somlo@cmu.edu>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Artyom Tarasenko <atar4qemu@gmail.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Gabriel Somlo <somlo@cmu.edu>
Tested-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
We'd like to raise the value of FW_CFG_FILE_SLOTS. Doing it naively could
lead to problems with backward migration: a more recent QEMU (running an
older machine type) would allow the guest, in fw_cfg_select(), to select a
high key value that is unavailable in the same machine type implemented by
the older (target) QEMU. On the target host, fw_cfg_data_read() for
example could dereference nonexistent entries.
As first step, size the FWCfgState.entries[*] and FWCfgState.entry_order
arrays dynamically. All three array sizes will be influenced by the new
field FWCfgState.file_slots (and matching device property).
Make the following changes:
- Replace the FW_CFG_FILE_SLOTS macro with FW_CFG_FILE_SLOTS_MIN (minimum
count of fw_cfg file slots) in the header file. The value remains 0x10.
- Replace all uses of FW_CFG_FILE_SLOTS with a helper function called
fw_cfg_file_slots(), returning the new property.
- Eliminate the macro FW_CFG_MAX_ENTRY, and replace all its uses with a
helper function called fw_cfg_max_entry().
- In the MMIO- and IO-mapped realize functions both, allocate all three
arrays dynamically, based on the new property.
- The new property defaults to FW_CFG_FILE_SLOTS_MIN. This is going to be
customized in the following patches.
Cc: "Gabriel L. Somlo" <somlo@cmu.edu>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Gabriel Somlo <somlo@cmu.edu>
Tested-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Useful to send guest data back to QEMU.
Changes from Laszlo Ersek <lersek@redhat.com>:
- rebase the patch from Michael Tsirkin's original postings at [1] and [2]
to the following patches:
- loader: Allow a custom AddressSpace when loading ROMs
- loader: Add AddressSpace loading support to uImages
- loader: fix handling of custom address spaces when adding ROM blobs
- reject such writes immediately that would exceed the end of the array,
rather than performing a partial write before setting the error bit: see
the (len != dma.length) condition
- document the write interface
[1] http://lists.nongnu.org/archive/html/qemu-devel/2016-02/msg04968.html
[2] http://lists.nongnu.org/archive/html/qemu-devel/2016-03/msg02735.html
Cc: "Gabriel L. Somlo" <somlo@cmu.edu>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <zhaoshenglong@huawei.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Gabriel Somlo <somlo@cmu.edu>
Tested-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
This patches implements Device IOTLB support for vhost kernel. This is
done through:
1) switch to use dma helpers when map/unmap vrings from vhost codes
2) introduce a set of VhostOps to:
- setting up device IOTLB request callback
- processing device IOTLB request
- processing device IOTLB invalidation
2) kernel support for Device IOTLB API:
- allow vhost-net to query the IOMMU IOTLB entry through eventfd
- enable the ability for qemu to update a specified mapping of vhost
- through ioctl.
- enable the ability to invalidate a specified range of iova for the
device IOTLB of vhost through ioctl. In x86/intel_iommu case this is
triggered through iommu memory region notifier from device IOTLB
invalidation descriptor processing routine.
With all the above, kernel vhost_net can co-operate with userspace
IOMMU. For vhost-user, the support could be easily done on top by
implementing the VhostOps.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYeOOmAAoJEPvQ2wlanipE3ZUH/Rsfpl23kXCMmqoXEIhWXy+h
yf8ARWCmpU6UKfwb+sH4vLegBfU56f62vVkGQ6oaaAbuyQ4SxCUlZGMO/rqY8/TE
m57aM+VfEE+bIdinAtLjFM24EVp/exMfkeutK7ItzLv7GwlrBos0J5veyCuyJ15q
pccV24jrpbJGilEeJ2GblKp3r2I3dInQGauOQhtoP3MNjHmYNSQD7noSbdN/JiTR
9H2eV700pg3ZPaSfO+CTVQN+cHjK1FC6qLi6916YZY9llnSOnDAegBYgbwE1RIBw
AULpWrezYveKy71eFhHVtGxnPeCJ8J4GVECMK0P0cdxzprIXFh1kZezyM4bxAGk=
=sboI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-tcg-common-tlb-reset-20170113-r1' into staging
This is the same as the v3 posted except a re-base and a few extra signoffs
# gpg: Signature made Fri 13 Jan 2017 14:26:46 GMT
# gpg: using RSA key 0xFBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>"
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-tcg-common-tlb-reset-20170113-r1:
cputlb: drop flush_global flag from tlb_flush
cpu_common_reset: wrap TCG specific code in tcg_enabled()
qom/cpu: move tlb_flush to cpu_common_reset
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Copy the mechanism of hw/smbios/smbios-stub.c to implement an ACPI-stub
instead, so that -acpitable can be later extended to ARM.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the useless is_external argument. Since the iohandler
AioContext is never used for block devices, aio_disable_external
is never called on it. This lets us remove stubs/iohandler.c.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
They are small, it is not worth stubbing them. Just include them
in user-mode emulators and unit tests as well.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-smbios command line options were accepted but silently ignored on
TARGET_ARM, due to a test for TARGET_I386 in arch_init.c.
Copy the mechanism of hw/pci/pci-stub.c to implement an smbios-stub
instead, enabled for all targets without CONFIG_SMBIOS.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Message-Id: <20161222151828.28292-1-leif.lindholm@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is complex, but I think it is reasonably documented in the source.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170112180800.21085-5-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This will make it possible to walk the list of bottom halves without
holding the AioContext lock---and in turn to call bottom half
handlers without holding the lock.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170112180800.21085-4-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
A QemuLockCnt comprises a counter and a mutex, with primitives
to increment and decrement the counter, and to take and release the
mutex. It can be used to do lock-free visits to a data structure
whenever mutexes would be too heavy-weight and the critical section
is too long for RCU.
This could be implemented simply by protecting the counter with the
mutex, but QemuLockCnt is harder to misuse and more efficient.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170112180800.21085-3-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This will be used for AioHandlers too. There is going to be little
or no contention, so it is better to reuse the same lock.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20170112180800.21085-2-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
bdrv_io_plug and bdrv_io_unplug are only called (via their
BlockBackend equivalents) after starting asynchronous I/O.
bdrv_drain is not going to be called while they are running,
because---even if a coroutine runs for some reason---it will
only drain in the next iteration of the event loop through
bdrv_co_yield_to_drain.
So this mechanism is unnecessary, get rid of it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20161129113334.605-1-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We have never has the concept of global TLB entries which would avoid
the flush so we never actually use this flag. Drop it and make clear
that tlb_flush is the sledge-hammer it has always been.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
[DG: ppc portions]
Acked-by: David Gibson <david@gibson.dropbear.id.au>
so it won't impose an additional limits on max_cpus limits
supported by different targets.
It removes global MAX_CPUMASK_BITS constant and need to
bump it up whenever max_cpus is being increased for
a target above MAX_CPUMASK_BITS value.
Use runtime max_cpus value instead to allocate sufficiently
sized node_cpu bitmasks in numa parser.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1479466974-249781-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
[ehabkost: Added asserts to ensure cpu_index < max_cpus]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Considering 'id' is mandatory for user_creatable objects/backends
and user_creatable_add_type() always has it as an argument
regardless of where from it is called CLI/monitor or QMP,
Fix issue by adding 'id' property to hostmem backends and
set it in user_creatable_add_type() for every object that
implements 'id' property. Then later at query-memdev time
get 'id' from object directly.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1484052795-158195-4-git-send-email-imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Simplify code by dropping ~57LOC by merging user_creatable_add()
into user_creatable_add_opts() and using the later from monitor.
Along with it allocate opts_visitor_new() once in user_creatable_add_opts().
As result we have one less API func and a more readable/simple
user_creatable_add_opts() vs user_creatable_add().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1484052795-158195-3-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
For builds with Mingw-w64 as it is included in Cygwin, there are two
header files which define KEY_EVENT with different values.
This results in lots of compiler warnings like this one:
CC vl.o
In file included from /qemu/include/ui/console.h:340:0,
from /qemu/vl.c:76:
/usr/i686-w64-mingw32/sys-root/mingw/include/curses.h:1522:0: warning: "KEY_EVENT" redefined
#define KEY_EVENT 0633 /* We were interrupted by an event */
In file included from /usr/share/mingw-w64/include/windows.h:74:0,
from /usr/share/mingw-w64/include/winsock2.h:23,
from /qemu/include/sysemu/os-win32.h:29,
from /qemu/include/qemu/osdep.h:100,
from /qemu/vl.c:24:
/usr/share/mingw-w64/include/wincon.h:101:0: note: this is the location of the previous definition
#define KEY_EVENT 0x1
QEMU only uses the KEY_EVENT macro from wincon.h.
Therefore we can undefine the macro coming from curses.h.
The explicit include statement for curses.h in ui/curses.c is not needed
and was removed.
Those two modifications fix the redefinition warnings.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Message-id: 20161119185318.10564-1-sw@weilnetz.de
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This adds two console functions, qemu_console_set_window_id and
qemu_graphic_console_get_window_id, to let graphical backend record the
window id in the QemuConsole structure, and let the baum driver read it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Message-id: 20161221003806.22412-2-samuel.thibault@ens-lyon.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Wayland always uses evdev as its input source, so QEMU
can use the existing evdev keymap data
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Tested-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20161201094117.16407-1-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
That reduces DSDT by 910 bytes when memory hotplug
isn't enabled.
While doing so drop intermediate variables/arguments
passing around ACPI_MEMORY_HOTPLUG_IO_LEN and making
it local to memory_hotplug.c, hardcoding it there as
it can't change.
Also don't pass around ACPI_MEMORY_HOTPLUG_BASE through
intermediate variables/arguments where it's not needed.
Instead initialize in module static variable when MMIO
region is mapped and use that within memory_hotplug.c
whenever it's required.
That way MMIO base specified only at one place and AML
with MMIO would always use the same value.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Move defines used locally only by memory_hotplug.c into it
from header files.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
>From this patch all the memory hotplug related AML
bits are consolidated in one place within DSTD.
Follow up patches will utilize that to simplify
memory hotplug related C/AML code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
It consolidates memory hotplug AML in one place within DSDT
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
since static and dynamic parts of memory MHPD device are now
in the same table (DSDT), there is no point keeping
them scattered across the table, so consolidate it
in one place.
There aren't any functional change, only AML text movement
from externally refferenced MHPD scope directly into
MHPD device declaration.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
This patch allows advising guest with host MTU's by setting
host_mtu parameter.
If VIRTIO_NET_F_MTU has been successfully negotiated, MTU
value is passed to the backend.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Aaron Conole <aconole@redhat.com
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch provides a way for virtio-net to notify the
backend about the host MTU set by the user.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Aaron Conole <aconole@redhat.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch implements VHOST_USER_PROTOCOL_F_NET_MTU
protocol feature and VHOST_USER_NET_SET_MTU request so
that the backend gets notified of the user defined host
MTU.
If backend supports VHOST_USER_PROTOCOL_F_REPLY_ACK,
QEMU assumes MTU is valid if success is returned.
Vhost-net driver sends this request through a new
vhost_net_set_mtu vhost_ops entry.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Aaron Conole <aconole@redhat.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add procedure for fast drop of queued packets, acting like
pop and push without mapping the buffers into memory.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Bring virtio queue to correct internal state for host-to-guest
operations when vhost is temporary stopped.
Signed-off-by: Yuri Benditovich <yuri.benditovich@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now, AER capa version is fixed to v2, if assigned device isn't v2,
then this value will be inconsistent between guest and host
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When user specify invalid value for property aer_log_max, device should
fail to create, and report appropriate message.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The ready flag should be set by the children of
cryptodev backend interface. Warp the setter/getter
functions for it.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pavel Dovgalyuk