Introduce and use the "unplug" callback.
This is a preparation for multi-stage hotplug handlers, whereby the bus
hotplug handler is overwritten by the machine hotplug handler. This handler
will then pass control to the bus hotplug handler. So to get this running
cleanly, we also have to make sure to go via the hotplug handler chain when
actually unplugging a device after an unplug request. Lookup the hotplug
handler and call "unplug".
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For now, the hotplug handler is not called for devices that are
being cold plugged. The hotplug handler is setup when the machine
initialization is fully done. Only bridges that were cold plugged are
considered.
Set the hotplug handler for the root piix bus directly when realizing.
Overwrite the hotplug handler of bridges when coldplugging them.
This will now make sure that the ACPI PCI hotplug handler is also called
for cold plugged devices (also on bridges) but not for bridges that were
hotplugged (keeping the current behavior).
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Perform the check in the pre_plug handler. In addition, we need the
capability only if the device is actually hotplugged (and not created
during machine initialization). This is a preparation for coldplugging
pci devices via that hotplug handler.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Pierre Morel<pmorel@linux.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
While at it, also rename shpc_device_hotplug_common() to
shpc_device_plug_common().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
While at it, also rename pcie_cap_slot_hotplug_common() to
pcie_cap_slot_plug_common().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
They've been deprecated for two releases and nobody complained that they
are still required anymore, so it's time to remove these now.
And while we're at it, mark the other remaining old 0.x machine types
as deprecated (since they can not properly be used for live-migration
anyway).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
The only remaining AcpiRsdpDescriptor users are the ACPI utils for the
BIOS table tests.
We remove that dependency and can thus remove the structure itself.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since "s390x/tcg: avoid overflows in time2tod/tod2time", the
time2tod() function tries to deal with the 9 uppermost bits in the
time value, but uses the wrong mask for this: 0xff80000000000000 should
be used instead of 0xff10000000000000 here.
Fixes: 14055ce53c
Cc: qemu-stable@nongnu.org
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1544792887-14575-1-git-send-email-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
[CH: tweaked commit message]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Taking the address of a field in a packed struct is a bad idea, because
it might not be actually aligned enough for that pointer type (and
thus cause a crash on dereference on some host architectures). Newer
versions of clang warn about this.
Avoid the problem by using local copies of the PMCW and SCSW
struct fields in copy_schib_from_guest() and copy_schib_to_guest().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20181213120252.21697-1-peter.maydell@linaro.org>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
configure gets the version number from VERSION, and writes it to
config-host.mak. The make dependency for that is missing. Because of
that, a rebuild after a VERSION change may not pick up the change.
Fix that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20181214084754.23854-1-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the changes
to the following files manually reverted:
contrib/libvhost-user/libvhost-user-glib.h
contrib/libvhost-user/libvhost-user.c
contrib/libvhost-user/libvhost-user.h
linux-user/mips64/cpu_loop.c
linux-user/mips64/signal.c
linux-user/sparc64/cpu_loop.c
linux-user/sparc64/signal.c
linux-user/x86_64/cpu_loop.c
linux-user/x86_64/signal.c
target/s390x/gen-features.c
tests/migration/s390x/a-b-bios.c
tests/test-rcu-simpleq.c
tests/test-rcu-tailq.c
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20181204172535.2799-1-armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Viktor Prutyanov <viktor.prutyanov@phystech.edu>
Now that build_rsdp() supports building both legacy and current RSDP
tables, we can move it to a generic folder (hw/acpi) and have the i386
ACPI code reuse it in order to reduce code duplication.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
We add the ability to build legacy or current RSDP tables, based on the
AcpiRsdpData revision field passed to build_rsdp().
Although arm/virt only uses RSDP v2, adding that capability to
build_rsdp will allow us to share the RSDP build code between ARM and x86.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of filling a mapped and packed C structure field in random order
and being careful about endianness and sizes, build_rsdp() now uses
build_append_int_noprefix() to compose RSDP table.
This makes reviewing and maintaining code easier as this is almost
matching 1:1 the ACPI spec itself.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
That will allow us to generalize the ARM build_rsdp() routine to support
both legacy RSDP (The current i386 implementation) and extended RSDP
(The ARM implementation).
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
AcpiRsdpDescriptor describes revision 2 RSDP table so using sizeof(*rsdp)
for checksum calculation isn't correct since we are adding extra 16 bytes.
But acpi_data_push() zeroes out table, so just by luck we are summing up
exta zeros which still yelds correct checksum.
Fix it up by explicitly stating table size instead of using
pointer arithmetics on stucture.
PS:
Extra 16 bytes are still wasted, but droping them will break migration
for machines older than 2.3 due to size mismatch, for 2.3 and older it's
not an issue since they are using resizable memory regions (a1666142d)
for ACPI blobs. So keep wasting memory to avoid breaking old machines.
Fixes: 72c194f7e (i386: ACPI table generation code from seabios)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When RSDP table was introduced (d4bec5d87), we calculated only legacy
checksum, and that was incorrect as it
- specified rev=2 and forgot about extended checksum.
- legacy checksum calculated on full table instead of the 1st 20 bytes
Fix it by adding extended checksum calculation and using correct
size for legacy checksum.
While at it use explicit constants to specify sub/full tables
sizes instead of relying on AcpiRsdpDescriptor size and fields offsets.
The follow up commits will convert this table to build_append_int_noprefix() API,
will use constants anyway and remove unused AcpiRsdpDescriptor structure.
Based on "[PATCH v5 05/24] hw: acpi: Implement XSDT support for RSDP"
by Samuel Ortiz, who did it right in his impl.
Fixes: d4bec5d87 ("hw/arm/virt-acpi-build: Generate RSDP table")
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
CC: Ard Biesheuvel <ard.biesheuvel@linaro.org>
CC: Shannon Zhao <shannon.zhaosl@gmail.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For both x86 and ARM architectures, the internal RSDP build API can
return void as the current return value is unused.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We're going to have 57bits aw-bits support sooner. It's possibly time
to remove the "x-" prefix.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Support DMA read/write draining should be easy for existing VT-d
emulation since the emulation itself does not have any request queue
there so we don't need to do anything to flush the un-commited queue.
What we need to do is to declare the support.
These capabilities are required to pass Windows SVVP test program. It
is verified that when with parameters "x-aw-bits=48,caching-mode=off"
we can pass the Windows SVVP test with this patch applied. Otherwise
we'll fail with:
IOMMU[0] - DWD (DMA write draining) not supported
IOMMU[0] - DWD (DMA read draining) not supported
Segment 0 has no DMA remapping capable IOMMU units
However since these bits are not declared support for QEMU<=3.1, we'll
need a compatibility bit for it and we turn this on by default only
for QEMU>=4.0.
Please refer to VT-d spec 6.5.4 for more information.
CC: Yu Wang <wyu@redhat.com>
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1654550
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Report more *_invalid() tracepoints to error_report_once() so that we
can detect issues even without tracing enabled. Drop those tracepoints.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The iotlb.iova can be zero if failure really happened. Dump the addr
instead.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Change the default speed and width for new machine types to the
fastest and widest currently supported. This should be compatible to
the PCIe 4.0 spec. Pre-QEMU-4.0 machine types remain at 2.5GT/s, x1
width.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that the downstream port will virtually negotiate itself to the
link status of the downstream device, we can remove this emulation.
It's not clear that it was every terribly useful anyway.
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allow users to experimentally specify speed and width values for the
generic PCIe root port. Defaults remain at 2.5GT/s & x1 for
compatiblity with the intent to only support changing defaults via
machine types for now.
Note for libvirt testing that pcie-root-port controllers are given
default names like "pci.7" which don't play well with using the
"-set device.$name.$prop=$value" options accessible to us via
<qemu:commandline> options. The solution is to add an <alias> to the
pcie-root-port <controller>, for example:
<controller type='pci' index='7' model='pcie-root-port'>
<model name='pcie-root-port'/>
<target chassis='7' port='0x15'/>
<alias name='ua-gfx0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x5'/>
</controller>
The "ua-" here is a mandatory prefix. We can then use:
<qemu:commandline>
<qemu:arg value='-set'/>
<qemu:arg value='device.ua-gfx0.x-speed=8'/>
<qemu:arg value='-set'/>
<qemu:arg value='device.ua-gfx0.x-width=16'/>
</qemu:commandline>
or, without an alias, set globals such as:
<qemu:commandline>
<qemu:arg value='-global'/>
<qemu:arg value='pcie-root-port.x-speed=8'/>
<qemu:arg value='-global'/>
<qemu:arg value='pcie-root-port.x-width=16'/>
</qemu:commandline>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make use of the PCIESlot speed and width fields to update link
information beyond those configured in pcie_cap_v1_fill(). This is
only called for devices supporting a version 2 capability and
automatically skips any non-PCIESlot devices. Only devices with
increased link values generate any visible config space differences.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add fields allowing the PCIe link speed and width of a PCIESlot to
be configured, with an instance_post_init callback on the root port
parent class to set defaults. This allows child classes to set these
via properties or via their own instance_init callback, without
requiring all implementions to support arbitrary user selected values.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Create properties to be able to define speeds and widths for PCIe
links. The only tricky bit here is that our get and set callbacks
translate from the fixed QAPI automagic enums to those we define
in PCI code to represent the actual register segment value.
Cc: Eric Blake <eblake@redhat.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PCIe link speed and width between a downstream device and its
upstream port is negotiated on real hardware and susceptible to
dynamic changes due to signal issues and power management. In the
emulated device case there is no real hardware link, but we still
might wish to have some consistency between endpoint and downstream
port via a virtual negotiation. There is of course a real link for
assigned devices and this same virtual negotiation allows the
downstream port to match the endpoint, synchronizing on every read
to support underlying physical hardware dynamically adjusting the
link.
This negotiation is intentionally unidirectional for compatibility.
If the endpoint exceeds the capabilities of the downstream port or
there is no endpoint device, the downstream port reports negotiation
to its maximum speed and width, matching the previous case where
negotiation was absent. De-tuning the endpoint to match a virtual
link doesn't seem to benefit anyone and is a condition we've thus
far reported without functional issues.
Note that PCI_EXP_LNKSTA is already ignored for migration
compatibility via pcie_cap_v1_fill().
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In preparation for reporting higher virtual link speeds and widths,
create enums and macros to help us manage them.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When loadvm'ing a *running* snapshot qemu crashes due to an invalid
free. It's fortunately caught early by glibc heap memory corruption
protection and qemu gets killed with SIGABRT.
Steps to reproduce:
1) Create VM (e.g w/ virsh define)
2) Start the VM and take a snapshot while it's running and having a
PCI bridge attached
3) Destroy the VM and revert the running snapshot.
This commit fixes the issue.
Signed-off-by: Matthias Weckbecker <matthias@weckbecker.name>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SMBIOS is just another firmware interface used by some QEMU models.
We will later introduce more firmware interfaces in this subdirectory.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This header only declare a single function: smbios_build_type_38_table().
We already have a header that declares such functions: "smbios_build.h".
Move the declaration and remove the header.
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All the consumers of "hw/smbios/ipmi.h" are located in hw/smbios/.
There is no need to have this include publicly exposed,
reduce the visibility by moving it in hw/smbios/.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The "hw/smbios/smbios.h" include is not used, remove it.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Many of the current virtio-*-pci device types actually represent
3 different types of devices:
* virtio 1.0 non-transitional devices
* virtio 1.0 transitional devices
* virtio 0.9 ("legacy device" in virtio 1.0 terminology)
That would be just an annoyance if it didn't break our device/bus
compatibility QMP interfaces. With these multi-purpose device
types, there's no way to tell management software that
transitional devices and legacy devices require a Conventional
PCI bus.
The multi-purpose device types would also prevent us from telling
management software what's the PCI vendor/device ID for them,
because their PCI IDs change at runtime depending on the bus
where they were plugged.
This patch adds separate device types for each of those virtio
device flavors:
- virtio-*-pci: the existing multi-purpose device types
- Configurable using `disable-legacy` and `disable-modern`
properties
- Legacy driver support is automatically enabled/disabled
depending on the bus where it is plugged
- Supports Conventional PCI and PCI Express buses
(but Conventional PCI is incompatible with
disable-legacy=off)
- Changes PCI vendor/device IDs at runtime
- virtio-*-pci-transitional: virtio-1.0 device supporting legacy drivers
- Supports Conventional PCI buses only, because
it has a PIO BAR
- virtio-*-pci-non-transitional: modern-only
- Supports both Conventional PCI and PCI Express buses
The existing TYPE_* macros for these types will point to an
abstract base type, so existing casts in the code will keep
working for all variants.
A simple test script (tests/acceptance/virtio_version.py) is
included, to check if the new device types are equivalent to
using the `disable-legacy` and `disable-modern` options.
Acked-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a helper for registering different flavours of virtio
devices. Convert code to use the helper, but keep only the
existing generic types. Transitional and non-transitional device
types will be added by another patch.
Acked-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Otherwise it won't be set up correctly and won't work after
miigration.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When VM boots from the latest version of linux kernel, after
hot-unpluging virtio-blk disks which are hotplugged into
pcie-root-port, the VM's dmesg log shows:
[ 151.046242] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0001 from Slot Status
[ 151.046365] pciehp 0000:00:05.0:pcie004: Slot(0-3): Attention button pressed
[ 151.046369] pciehp 0000:00:05.0:pcie004: Slot(0-3): Powering off due to button press
[ 151.046420] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 151.046425] pciehp 0000:00:05.0:pcie004: pciehp_green_led_blink: SLOTCTRL a8 write cmd 200
[ 151.046464] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 151.046468] pciehp 0000:00:05.0:pcie004: pciehp_set_attention_status: SLOTCTRL a8 write cmd c0
[ 156.163421] pciehp 0000:00:05.0:pcie004: pciehp_get_power_status: SLOTCTRL a8 value read 2f1
[ 156.163427] pciehp 0000:00:05.0:pcie004: pciehp_unconfigure_device: domain🚌dev = 0000:06:00
[ 156.198736] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 156.198772] pciehp 0000:00:05.0:pcie004: pciehp_power_off_slot: SLOTCTRL a8 write cmd 400
[ 157.224124] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0018 from Slot Status
[ 157.224194] pciehp 0000:00:05.0:pcie004: pciehp_green_led_off: SLOTCTRL a8 write cmd 300
[ 157.224220] pciehp 0000:00:05.0:pcie004: pciehp_check_link_active: lnk_status = 2011
[ 157.224223] pciehp 0000:00:05.0:pcie004: Slot(0-3): Link Up
[ 157.224233] pciehp 0000:00:05.0:pcie004: pciehp_get_power_status: SLOTCTRL a8 value read 7f1
[ 157.224281] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 157.224285] pciehp 0000:00:05.0:pcie004: pciehp_power_on_slot: SLOTCTRL a8 write cmd 0
[ 157.224300] pciehp 0000:00:05.0:pcie004: __pciehp_link_set: lnk_ctrl = 0
[ 157.224336] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 157.224339] pciehp 0000:00:05.0:pcie004: pciehp_green_led_blink: SLOTCTRL a8 write cmd 200
[ 159.739294] pci 0000:06:00.0 id reading try 50 times with interval 20 ms to get ffffffff
[ 159.739315] pciehp 0000:00:05.0:pcie004: pciehp_check_link_status: lnk_status = 2011
[ 159.739318] pciehp 0000:00:05.0:pcie004: Failed to check link status
[ 159.739371] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 159.739394] pciehp 0000:00:05.0:pcie004: pciehp_power_off_slot: SLOTCTRL a8 write cmd 400
[ 160.771426] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 160.771452] pciehp 0000:00:05.0:pcie004: pciehp_green_led_off: SLOTCTRL a8 write cmd 300
[ 160.771495] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 160.771499] pciehp 0000:00:05.0:pcie004: pciehp_set_attention_status: SLOTCTRL a8 write cmd 40
[ 160.771535] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 160.771539] pciehp 0000:00:05.0:pcie004: pciehp_green_led_off: SLOTCTRL a8 write cmd 300
After analyzing the log information, it seems that qemu doesn't
change the Link Status from active to inactive after hot-unplug.
This results in the abnormal log after the linux kernel commit
d331710ea78fea merged.
Furthermore, If I hotplug the same virtio-blk disk after hot-unplug,
the virtio-blk would turn on and then back off.
So this patch set the Link Status inactive after hot-unplug and
active after hot-plug.
Signed-off-by: Zheng Xiang <zhengxiang9@huawei.com>
Signed-off-by: Zheng Xiang <xiang.zheng@linaro.org>
Cc: Wang Haibin <wanghaibin.wang@huawei.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
- Exit boot-serial-test loop if child dies
- Sanitize verbose output in biot-tables-test
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJcF8nnAAoJEC7Z13T+cC21bGsP/RyyidCAs3/QAahL0O3UVjMP
Md9CgtUUl3swpKPoKyFXmyQGAfvfPKjAyQP0ESlxcQEAFgcr9MrX2OvGQCHSerUV
XtLB9k8d4vuSQn4diAVTTUU/iRZWstZGR5gkjXidBroXtYOLG8nO1MSPb0/pOH3l
osMHg+ItNPzTjr6kzaM/D5TXZFslMMJ0mriT5ayPHuBsK1dSerpSg6SSswvcOuUR
ZlhlWi4eNxTqO06uqv43AolOO8w5O12jgvtPxRiZw4j3Mvw8MPO2ZEB2bPlNjJ52
SrO8Tl3Tvx9SsUwv31oBKcHMf7xGePqErE6wgBBmORB67MbLPPSGL2VVADxoMI1u
n42bYwtLs0aAWfyXmgvUPScP2qRTwN7KQ5ETPDQNpov0ctUWi2O7NJXpkQzyz8WO
+bv4HYZFTQzUxaW4SnUP4h6XBgMWZl7zQkEl4oUNIBiacWrq+I/793I66hiFPTtX
o7j059HUqHYd3hETYX3GiScXBuHAdhXknhKEO8fSveBYMb0wPC9DfYkKL4c7gxfJ
p5jU9DBNn2JolCMttvCJsfHCmxcG2wwzBElxW2wCnKgMa3nuQPvBjxr0x3FKb0r8
f30pbnisNKowHG1VQXKm6gpJPOovA/JpIcA47egCqxuAWjSILEKpf169Y1HTtNQW
nZnBah35LEdcibdyTao1
=cz57
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2018-12-17' into staging
- Replace global_qtest in some tests
- Exit boot-serial-test loop if child dies
- Sanitize verbose output in biot-tables-test
# gpg: Signature made Mon 17 Dec 2018 16:08:07 GMT
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>"
# gpg: aka "Thomas Huth <thuth@redhat.com>"
# gpg: aka "Thomas Huth <huth@tuxfamily.org>"
# gpg: aka "Thomas Huth <th.huth@posteo.de>"
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2018-12-17:
tests/bios-tables-test: Sanitize test verbose output
tests: acpi: remove not used ACPI_READ_GENERIC_ADDRESS macro
tests: Exit boot-serial-test loop if child dies
tests/pxe: Make test independent of global_qtest
tests/prom-env: Make test independent of global_qtest
tests/machine-none: Make test independent of global_qtest
tests/test-filter: Make tests independent of global_qtest
tests/boot-serial: Get rid of global_qtest variable
tests/pvpanic: Make the pvpanic test independent of global_qtest
tests/vmgenid: Make test independent of global_qtest
tests/acpi-utils: Drop dependence on global_qtest
ivshmem-test: Drop dependence on global_qtest
tests/libqos/pci: Make PCI access functions independent of global_qtest
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It's going to clutter QEMU logs if 0x0f00 is trapped.
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20181203100415.53027-2-r.bolshakov@yadro.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Default branches variant should use the member conditional.
This fixes compilation with --disable-replication.
Fixes: 335d10cd8e
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181217204046.14861-1-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Long line wrapped]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The qmp/hmp command 'system_wakeup' is simply a direct call to
'qemu_system_wakeup_request' from vl.c. This function verifies if
runstate is SUSPENDED and if the wake up reason is valid before
proceeding. However, no error or warning is thrown if any of those
pre-requirements isn't met. There is no way for the caller to
differentiate between a successful wakeup or an error state caused
when trying to wake up a guest that wasn't suspended.
This means that system_wakeup is silently failing, which can be
considered a bug. Adding error handling isn't an API break in this
case - applications that didn't check the result will remain broken,
the ones that check it will have a chance to deal with it.
Adding to that, the commit before previous created a new QMP API called
query-current-machine, with a new flag called wakeup-suspend-support,
that indicates if the guest has the capability of waking up from suspended
state. Although such guest will never reach SUSPENDED state and erroring
it out in this scenario would suffice, it is more informative for the user
to differentiate between a failure because the guest isn't suspended versus
a failure because the guest does not have support for wake up at all.
All this considered, this patch changes qmp_system_wakeup to check if
the guest is capable of waking up from suspend, and if it is suspended.
After this patch, this is the output of system_wakeup in a guest that
does not have wake-up from suspend support (ppc64):
(qemu) system_wakeup
wake-up from suspend is not supported by this guest
(qemu)
And this is the output of system_wakeup in a x86 guest that has the
support but isn't suspended:
(qemu) system_wakeup
Unable to wake up: guest is not in suspended state
(qemu)
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20181205194701.17836-4-danielhb413@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This patch updates the descriptions of 'guest-suspend-ram' and
'guest-suspend-hybrid' to mention that both commands relies now
on the proper support for wake up from suspend, retrieved by the
'wakeup-suspend-support' attribute of the 'query-current-machine'
QMP command.
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Message-Id: <20181205194701.17836-3-danielhb413@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
David Hildenbrand