For the PER instruction-fetch, we can't use the QEMU breakpoint
infrastructure as it triggers for a single address and not a full
address range, and as it actually stop before the instruction and
not before.
We therefore call an helper with the just fetched instruction address,
which check if the address is within the PER address range. If it is
the case, an event is recorded and will be signaled through an
exception.
Note that we implement here the PER-3 behaviour, that is an invalid
opcode is not considered as an instruction fetch. Without PER-3 this
behavious is undefined.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
For the PER successful-branching event support, we can't rely on any
QEMU infrastucture. We therefore call an helper in all places where
a branch can be taken. We have to pay attention to the branch to next
case, as it's still a taken branch.
We don't need to care about the cases using goto_tb, as we have disabled
them in the previous patch.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch add basic support to generate PER exceptions. It adds two
fields to the cpu structure to record for the PER address and PER
code & ATMID values. When an exception is triggered and a PER event is
pending, the two PER values are copied to the lowcore area.
At the end of an instruction, an helper is checking for a possible
pending PER event and triggers an exception in that case. For that to
work with branches, we need to disable TB chaining when PER is
activated. Fortunately it's already in the TB flags.
Finally in case of a SERVICE CALL exception, we need to trigger the PER
exception immediately after.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
The code handling the I/O instructions for KVM decodes the instruction
itself. In TCG mode also pass the full instruction word to the helpers.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
DIAG IPL is already implemented for KVM, but not wired from TCG. For
that change the format of the instruction so that we can get R1 and R3
numbers in addition to the function code.
The diag function can change plenty of things, including CC, so we
should enter with a static CC. Also it doesn't set the value of general
register 2 to 0 as in the current code. We also need to exit the CPU
loop after a reset, which means a new PSW.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
It is part of the basic zArchitecture instructions.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
It is part of the basic zArchitecture instructions. Allow it to be call
from EXECUTE.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is needed to pass the gcc.c-torture/execute/ieee/20010114-2.c test
in the gcc testsuite.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that movcond exists, it's easy to write (negative-) absolute value
using TCG code instead of an helper.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
Rather than include helper.h with N values of GEN_HELPER, include a
secondary file that sets up the macros to include helper.h. This
minimizes the files that must be rebuilt when changing the macros
for file N.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The division routines do not read or write tcg registers,
but can raise fixed-point divide exceptions.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Aurelien Jarno