Occasionally in Linux guests on x86_64 we're seeing logs like:
ppc_set_irq: 0x55b4e0d562f0 n_IRQ 8 level 1 => pending 00000100req 00000004
when they should read:
ppc_set_irq: 0x55b4e0d562f0 n_IRQ 8 level 1 => pending 00000100req 00000002
The "00000004" is CPU_INTERRUPT_EXITTB yet the code calls
cpu_interrupt(cs, CPU_INTERRUPT_HARD) ("00000002") in this function
just before the log message. Something is causing the HARD bit setting
to get lost.
The knock on effect of losing that bit is the decrementer timer interrupts
don't get delivered which causes the guest to sit idle in its idle handler
and 'hang'.
The issue occurs due to races from code which sets CPU_INTERRUPT_EXITTB.
Rather than poking directly into cs->interrupt_request, that code needs to:
a) hold BQL
b) use the cpu_interrupt() helper
This patch fixes the call sites to do this, fixing the hang. The calls
are made from a variety of contexts so a helper function is added to handle
the necessary locking. This can likely be improved and optimised in the future
but it ensures the code is correct and doesn't lockup as it stands today.
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The msr invalidation code (commits 993eb and 2360b) inverts all
bits except MSR_TGPR and MSR_HVB. On non PowerPC 601 processors
this leads to incorrect change of excp_prefix in hreg_store_msr()
function. The problem is that new msr value get multiplied by msr_mask
and inverted msr does not, thus values of MSR_EP bit in new msr value
and inverted msr are distinct, so that excp_prefix changes but should
not.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
cpu->compat_pvr is used to store the current compat mode of the cpu.
On the receiving side during incoming migration we check compatibility
with the compat mode by calling ppc_set_compat(). However we fail to set
the compat mode with the hypervisor since the "new" compat mode doesn't
differ from the current (due to a "cpu->compat_pvr != compat_pvr" check).
This means that kvm runs the vcpus without a compat mode, which is the
incorrect behaviour. The implication being that a compatibility mode
will never be in effect after migration.
To fix this so that the compat mode is correctly set with the
hypervisor, store the desired compat mode and reset cpu->compat_pvr to
zero before calling ppc_set_compat().
Fixes: 5dfaa532 ("ppc: fix ppc_set_compat() with KVM PR")
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Migration of a system under stress (for example, with
"stress-ng --numa 2") triggers on the destination
some kernel watchdog messages like:
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 3489660870s!
NMI watchdog: BUG: soft lockup - CPU#1 stuck for 3489660884s!
This problem appears with the changes introduced by
42043e4 spapr: clock should count only if vm is running
I think this commit only triggers the problem.
Kernel computes the soft lockup duration using the
Virtual Timebase register (VTB), not using the Timebase
Register (TBR, the one 42043e4 stops).
It appears VTB is not migrated, so this patch adds it in
the list of the SPRs to migrate, and fixes the problem.
For the migration, I've tested a migration from qemu-2.8.0 and
pseries-2.8.0 to a patched master (qemu-2.11.0-rc1). The received
VTB is 0 (as is it not initialized by qemu-2.8.0), but the value
seems to be ignored by KVM and a non zero VTB is used by the kernel.
I have no explanation for that, but as the original problem appears
only with SMP system under stress I suspect some problems in KVM
(I think because VTB is shared by all threads of a core).
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
While trying to make KVM PR usable again, commit 5dfaa532ae introduced a
regression: the current compat_pvr value is passed to KVM instead of the
new one. This means that we always pass 0 instead of the max-cpu-compat
PVR during the initial machine reset. And at CAS time, we either pass
the PVR from the command line or even don't call kvmppc_set_compat() at
all, ie, the PCR will not be set as expected.
For example if we start a big endian fedora26 guest in power7 compat
mode on a POWER8 host, we get this in the guest:
$ cat /proc/cpuinfo
processor : 0
cpu : POWER7 (architected), altivec supported
clock : 4024.000000MHz
revision : 2.0 (pvr 004d 0200)
timebase : 512000000
platform : pSeries
model : IBM pSeries (emulated by qemu)
machine : CHRP IBM pSeries (emulated by qemu)
MMU : Hash
but the guest can still execute POWER8 instructions, and the following
program succeeds:
int main()
{
asm("vncipher 0,0,0"); // ISA 2.07 instruction
}
Let's pass the new compat_pvr to kvmppc_set_compat() and the program fails
with SIGILL as expected.
Reported-by: Nageswara R Sastry <rnsastry@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that every target is using the disas_set_info hook,
the flags argument is unused. Remove it.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This is identical for each target. So, move the initialization to
common code. Move the variable itself out of tcg_ctx and name it
cpu_env to minimize changes within targets.
This also means we can remove tcg_global_reg_new_{ptr,i32,i64},
since there are no longer global-register temps created by targets.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Groundwork for supporting multiple TCG contexts.
The core of this patch is this change to tcg/tcg.h:
> -extern TCGContext tcg_ctx;
> +extern TCGContext tcg_init_ctx;
> +extern TCGContext *tcg_ctx;
Note that for now we set *tcg_ctx to whatever TCGContext is passed
to tcg_context_init -- in this case &tcg_init_ctx.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Convert all existing readers of tb->cflags to tb_cflags, so that we
use atomic_read and therefore avoid undefined behaviour in C11.
Note that the remaining setters/getters of the field are protected
by tb_lock, and therefore do not need conversion.
Luckily all readers access the field via 'tb->cflags' (so no foo.cflags,
bar->cflags in the code base), which makes the conversion easily
scriptable:
FILES=$(git grep 'tb->cflags' target include/exec/gen-icount.h \
accel/tcg/translator.c | cut -f1 -d':' | sort | uniq)
perl -pi -e 's/([^.>])tb->cflags/$1tb_cflags(tb)/g' $FILES
perl -pi -e 's/([a-z->.]*)(->|\.)tb->cflags/tb_cflags($1$2tb)/g' $FILES
Then manually fixed the few errors that checkpatch reported.
Compile-tested for all targets.
Suggested-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Move target cpu tcg initialization to common code,
called from cpu_exec_realizefn.
Acked-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When we used structures for TCGv_*, we needed a macro in order to
perform a comparison. Now that we use pointers, this is just clutter.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
use generic cpu_model parsing introduced by
(6063d4c0f vl.c: convert cpu_model to cpu type and set of global properties before machine_init())
it allows to:
* replace sPAPRMachineClass::tcg_default_cpu with
MachineClass::default_cpu_type
* drop cpu_parse_cpu_model() from hw/ppc/spapr.c and reuse
one in vl.c
* simplify spapr_get_cpu_core_type() by removing
not needed anymore recurrsion since alias look up
happens earlier at vl.c and spapr_get_cpu_core_type()
works only with resulted from that cpu type.
* spapr no more needs to parse/depend on being phased out
MachineState::cpu_model, all tha parsing done by generic
code and target specific callback.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
[dwg: Correct minor compile error]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
next commit will drop ppc_cpu_lookup_alias() declaration from header
and make it static which will break its last user ppc_cpu_class_by_name()
since ppc_cpu_class_by_name() defined before ppc_cpu_lookup_alias().
To avoid this move ppc_cpu_lookup_alias() right before
ppc_cpu_class_by_name().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
consolidate 'host' core type registration by moving it from
KVM specific code into spapr_cpu_core.c, similar like it's
done in x86 target.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
replace sPAPRCPUCoreClass::cpu_class with cpu type name
since it were needed just to get that at points it were
accessed.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
there is a dedicated callback CPUClass::parse_features
which purpose is to convert -cpu features into a set of
global properties AND deal with compat/legacy features
that couldn't be directly translated into CPU's properties.
Create ppc variant of it (ppc_cpu_parse_featurestr) and
move 'compat=val' handling from spapr_cpu_core.c into it.
That removes a dependency of board/core code on cpu_model
parsing and would let to reuse common -cpu parsing
introduced by 6063d4c0
Set "max-cpu-compat" property only if it exists, in practice
it should limit 'compat' hack to spapr machine and allow
to avoid including machine/spapr headers in target/ppc/cpu.c
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For POWER ISA v3.0, the XER bit CA32 needs to be set by the shift
right algebraic instructions whenever the CA bit is to be set. This
change affects the following instructions:
* Shift Right Algebraic Word (sraw[.])
* Shift Right Algebraic Word Immediate (srawi[.])
* Shift Right Algebraic Doubleword (srad[.])
* Shift Right Algebraic Doubleword Immediate (sradi[.])
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At the moment the only POWER9 model which is listed in qemu is v1.0 (aka
"DD1"). This is a very early (read, buggy) version which will never be
released to the public - it was included in qemu only for the convenience
of those doing bringup on the early silicon. For bonus points, we actually
had its PVR incorrect in the table (0x004e0000 instead of 0x004e0100). We
also never actually implemented the differences in behaviour (read, bugs)
that marked DD1 in qemu.
Now that we know the PVR for the substantially better v2.0 (DD2) chip,
include it and make it the default POWER9 in qemu. For the time being we
leave the DD1 definition in place for the poor souls (read, me) who still
need to work with DD1 hardware.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We don't have any 460 or 460F CPUs in QEMU, so the init functions
are just dead code. Let's simply remove them (translate_init.c
is already big enough without them).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It is used by all PPC targets; we can give the directory its own
Makefile.objs file, and include it directly from target/ppc.
target/s390 can do the same when it starts using it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----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=/+LV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20170927a' into staging
Migration pull 2017-09-27
# gpg: Signature made Wed 27 Sep 2017 14:56:23 BST
# gpg: using RSA key 0x0516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20170927a:
migration: Route more error paths
migration: Route errors up through vmstate_save
migration: wire vmstate_save_state errors up to vmstate_subsection_save
migration: Check field save returns
migration: check pre_save return in vmstate_save_state
migration: pre_save return int
migration: disable auto-converge during bulk block migration
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
When running with KVM PR, if a new HPT is allocated we need to inform
KVM about the HPT address and size. This is currently done by hacking
the value of SDR1 and pushing it to KVM in several places.
Also, migration breaks the guest since it is very unlikely the HPT has
the same address in source and destination, but we push the incoming
value of SDR1 to KVM anyway.
This patch introduces a new virtual hypervisor hook so that the spapr
code can provide the correct value of SDR1 to be pushed to KVM each
time kvmppc_put_books_sregs() is called.
It allows to get rid of all the hacking in the spapr/kvmppc code and
it fixes migration of nested KVM PR.
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Remove *all* unused CPU definitions as indicated by compile-time
`#if 0` constructs.
Signed-off-by: John Snow <jsnow@redhat.com>
[dwg: Removed some additional now-useless comments]
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Following commit aef77960, remove now-unused definitions from
cpu-models.h.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The use of KVM_PPC_GET_HTAB_FD is open-coded in kvmppc_read_hptes()
and kvmppc_write_hpte().
This patch modifies kvmppc_get_htab_fd() so that it can be used
everywhere we need to access the in-kernel htab:
- add an index argument
=> only kvmppc_read_hptes() passes an actual index, all other users
pass 0
- add an errp argument to propagate error messages to the caller.
=> spapr migration code prints the error
=> hpte helpers pass &error_abort to keep the current behavior
of hw_error()
While here, this also fixes a bug in kvmppc_write_hpte() so that it
opens the htab fd for writing instead of reading as it currently does.
This never broke anything because we currently never call this code,
as explained in the changelog of commit c1385933804bb:
"This support updating htab managed by the hypervisor. Currently
we don't have any user for this feature. This actually bring the
store_hpte interface in-line with the load_hpte one. We may want
to use this when we want to emulate henter hcall in qemu for HV
kvm."
The above is still true today.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When kvmppc_get_htab_fd() fails, its return value is propagated up to
qemu_savevm_state_iterate() or to qemu_savevm_state_complete_precopy().
All savevm handlers expect to receive a negative errno on error.
Let's patch kvmppc_get_htab_fd() accordingly.
While here, let's change htab_load() in the spapr code to also
propagate the error, since it doesn't make sense to abort() if
we couldn't get the htab fd from KVM.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Despite its name it is a 440 core CPU
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It never got used since its introduction (commit 7c43bca004).
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The following capabilities are VM specific:
- KVM_CAP_PPC_SMT_POSSIBLE
- KVM_CAP_PPC_HTAB_FD
- KVM_CAP_PPC_ALLOC_HTAB
If both KVM HV and KVM PR are present, checking them always return
the HV value, even if we explicitely requested to use PR.
This has no visible effect for KVM_CAP_PPC_ALLOC_HTAB, because we also
try the KVM_PPC_ALLOCATE_HTAB ioctl which is only suppored by HV. As
a consequence, the spapr code doesn't even check KVM_CAP_PPC_HTAB_FD.
However, this will cause kvmppc_hint_smt_possible(), introduced by
commit fa98fbfcdf, to report several VSMT modes (eg, Available
VSMT modes: 8 4 2 1) whereas PR only support mode 1.
This patch fixes all three anyway to use kvm_vm_check_extension(). It
is okay since the VM is already created at the time kvm_arch_init() or
kvmppc_reset_htab() is called.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All but a handful of files include exec/cpu-all.h via cpu.h only.
As these files already include cpu.h, let's just drop the additional
include.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170913132417.24384-2-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Tidy up some of the warn_report() messages after having converted them
to use warn_report().
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <9cb1d23551898c9c9a5f84da6773e99871285120.1505158760.git.alistair.francis@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert all the multi-line uses of fprintf(stderr, "warning:"..."\n"...
to use warn_report() instead. This helps standardise on a single
method of printing warnings to the user.
All of the warnings were changed using these commands:
find ./* -type f -exec sed -i \
'N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N; {s|fprintf(.*".*warning[,:] \(.*\)\\n"\(.*\));|warn_report("\1"\2);|Ig}' \
{} +
Indentation fixed up manually afterwards.
Some of the lines were manually edited to reduce the line length to below
80 charecters. Some of the lines with newlines in the middle of the
string were also manually edit to avoid checkpatch errrors.
The #include lines were manually updated to allow the code to compile.
Several of the warning messages can be improved after this patch, to
keep this patch mechanical this has been moved into a later patch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Anthony Perard <anthony.perard@citrix.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Jason Wang <jasowang@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <5def63849ca8f551630c6f2b45bcb1c482f765a6.1505158760.git.alistair.francis@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the host has both KVM PR and KVM HV loaded and we pass:
-machine pseries,accel=kvm,kvm-type=PR
the kvmppc_is_pr() returns false instead of true. Since the helper
is mostly used as fallback, it doesn't have any real impact with
recent kernels. A notable exception is the workaround to allow
migration between compatible hosts with different PVRs (eg, POWER8
and POWER8E), since KVM still doesn't provide a way to check if a
specific PVR is supported (see commit c363a37a45 for details).
According to the official KVM API documentation [1], KVM_PPC_GET_PVINFO
is "vm ioctl", but we check it as a global ioctl. The following function
in KVM is hence called with kvm == NULL and considers we're in HV mode.
int kvm_vm_ioctl_check_extension(struct kvm *kvm, long ext)
{
int r;
/* Assume we're using HV mode when the HV module is loaded */
int hv_enabled = kvmppc_hv_ops ? 1 : 0;
if (kvm) {
/*
* Hooray - we know which VM type we're running on. Depend on
* that rather than the guess above.
*/
hv_enabled = is_kvmppc_hv_enabled(kvm);
}
Let's use kvm_vm_check_extension() to fix the issue.
[1] https://www.kernel.org/doc/Documentation/virtual/kvm/api.txt
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Running QEMU with
qemu-system-ppc64 -M none -nographic -m 256
and executing
dump-guest-memory /dev/null 0 8192
results in segfault
Fix by checking if we have CPU, and exit with
error if there is no CPU:
(qemu) dump-guest-memory /dev/null
this feature or command is not currently supported
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20170913142036.2469-2-lvivier@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Move the calculation of a CPU's VCPU ID out of the generic PPC code
(ppc_cpu_realizefn()) and into sPAPR specific code
(spapr_cpu_core_realize()) where it belongs.
Unfortunately, due to the way things are ordered, we still need to
default the VCPU ID in ppc_cpu_realizfn() but at least doing that
doesn't require any interaction with sPAPR.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Remove cpu models that aren't implemented and are not
compiled/tested since they are under TODO ifdef
which isn't defined in sources.
If someone really needs a removed model he/she should add
as regular one with corresponding implementation.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Caching there practically doesn't give any benefits
and that at slow path druring querying supported CPU list.
But it introduces non conventional path of where from
comes used CPU type name (kvm_ppc_register_host_cpu_type).
Taking in account that kvm_ppc_register_host_cpu_type()
fixes up models the aliases point to, it's sufficient to
make ppc_cpu_class_by_name() translate cpu alias to
correct cpu type name.
So drop PowerPCCPUAlias::oc field + ppc_cpu_class_by_alias()
and let ppc_cpu_class_by_name() do conversion to cpu type name,
which simplifies code a little bit saving ~20LOC and trouble
wondering why ppc_cpu_class_by_alias() is necessary.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
previous patches cleaned up cpu model/alias naming which
allows to simplify cpu model/alias to cpu type lookup a bit
byt removing recurssion and dependency of ppc_cpu_class_by_name() /
ppc_cpu_class_by_alias() on each other.
Besides of simplifying code it reduces it by ~15LOC.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
alias pointing to another alias forces lookup code to
do recurrsive translation till real cpu model is reached.
Drop this nonsence and make each alias point to cpu model
that has corresponding CPU type. It will allow to drop
recurrsion in cpu model translation code and actually
make ppc_cpu_aliases[] content use PowerPCCPUAlias
fields properly
(i.e. alias goes into .alias and model goes into .model)
While at it add TODO defines around aliases that point to
cpu models excluded by the same TODO defines.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PPC handles -cpu FOO rather incosistently,
i.e. it does case-insensitive matching of FOO to
a CPU type (see: ppc_cpu_compare_class_name) but
handles alias names as case-sensitive, as result:
# qemu-system-ppc64 -M mac99 -cpu g3
qemu-system-ppc64: unable to find CPU model ' kN�U'
# qemu-system-ppc64 -cpu 970MP_V1.1
qemu-system-ppc64: Unable to find sPAPR CPU Core definition
while
# qemu-system-ppc64 -M mac99 -cpu G3
# qemu-system-ppc64 -cpu 970MP_v1.1
start up just fine.
Considering we can't take case-insensitive matching away,
make it case-insensitive for all alias/type/core_type
lookups.
As side effect it allows to remove duplicate core types
which are the same except of using different cased letters in name.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace
"-" TYPE_POWERPC_CPU
when composing cpu type name from cpu model string literal
and the same pattern in format strings with
POWERPC_CPU_TYPE_SUFFIX and POWERPC_CPU_TYPE_NAME(model)
macroses like we do in x86.
Later POWERPC_CPU_TYPE_NAME() will be used to define default
cpu type per machine type and as bonus it will be consistent
and easy grep-able pattern across all other targets that I'm
plannig to treat the same way.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The target/ppc/STATUS file has seen its last real update 10 years
ago - so the information in there is not up to date anymore. Since
nobody seems to care about this file, let's simply remove it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
KVM now allows writing to KVM_CAP_PPC_SMT which has previously been
read only. Doing so causes KVM to act, for that VM, as if the host's
SMT mode was the given value. This is particularly important on Power
9 systems because their default value is 1, but they are able to
support values up to 8.
This patch introduces a way to control this capability via a new
machine property called VSMT ("Virtual SMT"). If the value is not set
on the command line a default is chosen that is, when possible,
compatible with legacy systems.
Note that the intialization of KVM_CAP_PPC_SMT has changed slightly
because it has changed (in KVM) from a global capability to a
VM-specific one. This won't cause a problem on older KVMs because VM
capabilities fall back to global ones.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Richard Purdie