Also trace the extra registers, and update the comments with new
info from Artyom Tarasenko.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
ledma has 0x20 bytes of registers according to OBP, and at least Solaris9
reads the 5th register which is beyond what we've mapped. So let's setup
a flag (inspired by a previous patch from Blue Swirl) to identify ledma
from espdma, and map another 16 bytes of registers which return 0.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As stated before, devices can be little, big or native endian. The
target endianness is not of their concern, so we need to push things
down a level.
This patch adds a parameter to cpu_register_io_memory that allows a
device to choose its endianness. For now, all devices simply choose
native endian, because that's the same behavior as before.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Sending ESP a command caused it to trigger DMA immediately
even if DMA was not enabled at the DMA controller.
Add a signal from DMA controller to ESP to tell ESP about changes in
DMA enable bit. Also use the correct function for setting up GPIO outputs.
This fixes NetBSD 1.6.1 through 3.0 boot.
Thanks to Artyom Tarasenko for extensive debugging of the problem.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
On a real hardware changing read-only bits has no effect
Use a mask common for SCSI and Ethernet registers. The crucial
bit is DMA_INTR, because setting or clearing it may produce
spurious interrupts.
This patch allows booting Solaris 2.3
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Don't raise irq when not enabled.
Raise irq on enabling if DMA_INTR is set
Don't clear irq unless it was raised by DMA, as there are other irq sources
Don't set DMA_INTR bit spuriously.
v1->v2:
- Don't clear irq unless it was raised by DMA
- Raise irq on enabling if DMA_INTR is set
- Assume revertion of 787cfbc432
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
In the very least, a change like this requires discussion on the list.
The naming convention is goofy and it causes a massive merge problem. Something
like this _must_ be presented on the list first so people can provide input
and cope with it.
This reverts commit 99a0949b72.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Sorry folks, but it has to be. One more of these invasive qdev patches.
We have a serious design bug in the qdev interface: device init
callbacks can't signal failure because the init() callback has no
return value. This patch fixes it.
We have already one case in-tree where this is needed:
Try -device virtio-blk-pci (without drive= specified) and watch qemu
segfault. This patch fixes it.
With usb+scsi being converted to qdev we'll get more devices where the
init callback can fail for various reasons.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch is a major overhaul of the device properties. The properties
are saved directly in the device state struct now, the linked list of
property values is gone.
Advantages:
* We don't have to maintain the list with the property values.
* The value in the property list and the value actually used by
the device can't go out of sync any more (used to happen for
the pci.devfn == -1 case) because there is only one place where
the value is stored.
* A record describing the property is required now, you can't set
random properties any more.
There are bus-specific and device-specific properties. The former
should be used for properties common to all bus drivers. Typical
use case is bus addressing, i.e. pci.devfn and i2c.address.
Properties have a PropertyInfo struct attached with name, size and
function pointers to parse and print properties. A few common property
types have PropertyInfos defined in qdev-properties.c. Drivers are free
to implement their own very special property parsers if needed.
Properties can have default values. If unset they are zero-filled.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 8217606e6e (and
updates later added users of qemu_register_reset), we solved the
problem it originally addressed less invasively.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The parameter is always zero except when registering the three internal
io regions (ROM, unassigned, notdirty). Remove the parameter to reduce
the API's power, thus facilitating future change.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add the parameter 'order' to qemu_register_reset and sort callbacks on
registration. On system reset, callbacks with lower order will be
invoked before those with higher order. Update all existing users to the
standard order 0.
Note: At least for x86, the existing users seem to assume that handlers
are called in their registration order. Therefore, the patch preserves
this property. If someone feels bored, (s)he could try to identify this
dependency and express it properly on callback registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Bob Breuer