We were relying on msix_unset_vector_notifiers() to release all the
vectors when we disable MSI-X, but this only happens when MSI-X is
still enabled on the device. Perform further cleanup by releasing
any remaining vectors listed as in-use after this call. This caused
a leak of IRQ routes on hotplug depending on how the guest OS prepared
the device for removal.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: qemu-stable@nongnu.org
When MSI is enabled on Nvidia GeForce cards the driver seems to
acknowledge the interrupt by writing a 0xff byte to the MSI capability
ID register using the PCI config space mirror at offset 0x88000 from
BAR0. Without this, the device will only fire a single interrupt.
VFIO handles the PCI capability ID/next registers as virtual w/o write
support, so any write through config space is currently dropped. Add
a check for this and allow the write through the BAR window. The
registers are read-only anyway.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add and remove groups from the KVM virtual VFIO device as we make
use of them. This allows KVM to optimize for performance and
correctness based on properties of the group.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When an assigned device is initialized it copies the device config
space into the emulated config space. Unfortunately multifunction is
setup prior to the device initfn and gets clobbered. We need to
restore it just like pci-assign does.
Cc: qemu-stable@nongnu.org
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This causes two slight backwards-incompatibilities between "-M pc-1.5"
and 1.5's "-M pc":
(1) a fw_cfg file is removed with this patch. This is only a problem
if migration stops the virtual machine exactly during fw_cfg enumeration.
(2) after migration, a VM created without an explicit "-device pvpanic"
will stop reporting panics to management.
The first problem only occurs if migration is done at a very, very
early point (and I'm not sure it can happen in practice for reasonable-size
VMs, since it will likely take more time to send the RAM to destination,
than it will take for BIOS to scan fw_cfg).
The second problem only occurs if the guest panics _and_ has a guest
driver _and_ management knows to look at the crash event, so it is
mostly theoretical at this point in time.
Thus keep the code simple, and pretend it was never broken.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Turn PCMCIACardState into a device.
Move callbacks to new PCMCIACardClass.
Derive TYPE_MICRODRIVE from TYPE_PCMCIA_CARD.
Replace ide_init2_with_non_qdev_drives().
Signed-off-by: Othmar Pasteka <pasteka@kabsi.at>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Rename A9SCUState::busdev field to parent_obj and turn realizefn into an
instance_init function to allow early MMIO mapping.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSXNO8AAoJECgfDbjSjVRp7VAH/0B73mCOiyVACGx7fazK3SGK
X8TxZWVtG5A77ISqKyrtjLAhK9DCQjEzQTbMNhXHM3Ar6crwo7nJZnQvH2Gh1X2p
34BOQSVc4rtXz5pwDIr48dBLrxeslwXub79chUs+IK1/4RSn3h3nuS3k6JVkmLJN
rcHMj4ljJmi4Hd9vOpmS1jo/a61usi36hhU7CMgcrsXzStZycBBzCozOB3VW8p1X
/iwyf91YjmNPkn9gA3/aViGjszu8jE91dkA0C+ljwvcGbs2yEl3LCWEJfsMvoh5P
2M+k0XXbHwq/P9PFMa/2/lWOo4EO4Oxa+G/6QvovJrteYnktr+E9DqjU8pCT7yI=
=CVfs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci, pc, acpi fixes, enhancements
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 15 Oct 2013 07:33:48 AM CEST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
* mst/tags/for_anthony: (39 commits)
ssdt-proc: update generated file
ssdt: fix PBLK length
i386: ACPI table generation code from seabios
pc: use new api to add builtin tables
acpi: add interface to access user-installed tables
hpet: add API to find it
pvpanic: add API to access io port
ich9: APIs for pc guest info
piix: APIs for pc guest info
acpi/piix: add macros for acpi property names
i386: define pc guest info
loader: allow adding ROMs in done callbacks
i386: add bios linker/loader
loader: use file path size from fw_cfg.h
acpi: ssdt pcihp: updat generated file
acpi: pre-compiled ASL files
acpi: add rules to compile ASL source
i386: add ACPI table files from seabios
q35: expose mmcfg size as a property
q35: use macro for MCFG property name
...
Message-id: 1381818560-18367-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
Commit 9b8c69243 (since reverted) broke the ability to boot the kernel
as the value returned by unassigned_mem_read returned non-zero and left
the kernel looping forever waiting for it to change (see
integrator_led_set in the kernel code).
Relying on a varying implementation detail is incorrect anyway so this
introduces a basic stub of a memory region for the debug/LED section
on the integrator board.
Signed-off-by: Alex Bennée <alex@bennee.com>
Message-id: 1382451366-9539-1-git-send-email-alex.bennee@linaro.org
[PMM: removed three unused fields from struct IntegratorDebugState]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add API to find pvpanic device and get its io port.
Will be used to fill in guest info structure.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_set_irq and the other pci irq wrappers use
PCI_INTERRUPT_PIN config register to compute device
INTx pin to assert/deassert.
An irq is allocated using pci_allocate_irq wrapper
only if is needed by non pci devices.
Removed irq related fields from state if not used anymore.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_set_irq and the other pci irq wrappers use
PCI_INTERRUPT_PIN config register to compute device
INTx pin to assert/deassert.
save INTX pin into the config register before calling
pci_set_irq
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VFIO is always little endian so do byte swapping of our mask on the
way in and byte swapping of the size on the way out.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Just to be sure we don't jump off any NULL pointer cliffs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Memory regions can easily be 2^64 byte long and therefore overflow
for just a bit but that is enough for int128_get64() to assert.
This takes care of debug printing of huge section sizes.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Now that VFIO has a PCI hot reset interface, take advantage of it.
There are two modes that we need to consider. The first is when only
one device within the set of devices affected is actually assigned to
the guest. In this case the other devices are are just held by VFIO
for isolation and we can pretend they're not there, doing an entire
bus reset whenever the device reset callback is triggered. Supporting
this case separately allows us to do the best reset we can do of the
device even if the device is hotplugged.
The second mode is when multiple affected devices are all exposed to
the guest. In this case we can only do a hot reset when the entire
system is being reset. However, this also allows us to track which
individual devices are affected by a reset and only do them once.
We split our reset function into pre- and post-reset helper functions
prioritize the types of device resets available to us, and create
separate _one vs _multi reset interfaces to handle the distinct cases
above.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
During vfio-pci initfn, the device is not always in a state where the
option ROM can be read. In the case of graphics cards, there's often
no per function reset, which means we have host driver state affecting
whether the option ROM is usable. Ideally we want to move reading the
option ROM past any co-assigned device resets to the point where the
guest first tries to read the ROM itself.
To accomplish this, we switch the memory region for the option rom to
an I/O region rather than a memory mapped region. This has the side
benefit that we don't waste KVM memory slots for a BAR where we don't
care about performance. This also allows us to delay loading the ROM
from the device until the first read by the guest. We then use the
PCI config space size of the ROM BAR when setting up the BAR through
QEMU PCI.
Another benefit of this approach is that previously when a user set
the ROM to a file using the romfile= option, we still probed VFIO for
the parameters of the ROM, which can result in dmesg errors about an
invalid ROM. We now only probe VFIO to get the ROM contents if the
guest actually tries to read the ROM.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Not all resets are created equal. PM reset is not very reliable,
especially for GPUs, so we might want to opt for a bus reset if a
standard reset will only do a D3hot->D0 transition. We can also
use this to tell if the standard reset will do a bus reset (if
neither has_pm_reset or has_flr is probed, but the device still
supports reset).
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When MSI is accelerated through KVM the vectors are only programmed
when the guest first enables MSI support. Subsequent writes to the
vector address or data fields are ignored. Unfortunately that means
we're ignore updates done to adjust SMP affinity of the vectors.
MSI SMP affinity already works in non-KVM mode because the address
and data fields are read from their backing store on each interrupt.
This patch stores the MSIMessage programmed into KVM so that we can
determine when changes are made and update the routes.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
To be passed on to object_initialize_with_type().
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> (virtio-ccw)
Signed-off-by: Andreas Färber <afaerber@suse.de>
To be passed to object_initialize().
Since commit 39355c3826 the argument is
void*, so drop some superfluous (BusState *) casts or direct parent
field usages.
Signed-off-by: Andreas Färber <afaerber@suse.de>
* qemu-kvm/uq/master:
kvm-stub: fix compilation
kvm: shorten the parameter list for get_real_device()
kvm: i386: fix LAPIC TSC deadline timer save/restore
kvm-all.c: max_cpus should not exceed KVM vcpu limit
kvm: Simplify kvm_handle_io
kvm: x86: fix setting IA32_FEATURE_CONTROL with nested VMX disabled
kvm: add KVM_IRQFD_FLAG_RESAMPLE support
kvm: migrate vPMU state
target-i386: remove tabs from target-i386/cpu.h
Initialize IA32_FEATURE_CONTROL MSR in reset and migration
Conflicts:
target-i386/cpu.h
target-i386/kvm.c
aliguori: fixup trivial conflicts due to whitespace and added cpu
argument
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Added an EventNotifier* parameter to
kvm-all.c:kvm_irqchip_add_irqfd_notifier(), in order to give KVM
another eventfd to be used as "resamplefd". See the documentation
in the linux kernel sources in Documentation/virtual/kvm/api.txt
(section 4.75) for more details.
When the added parameter is passed NULL, the behaviour of the
function is unchanged with respect to the previous versions.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The ports at 0xe8..0xeb have impl.min/max_access_size == 1, so
that memory accesses are split and combined by the memory core.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1374501278-31549-29-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
So far the device was only used on little-endian machines.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1374501278-31549-18-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This will let us use the testdev to test endianness.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Message-id: 1374501278-31549-17-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Replace direct uses of IVShmemState::dev with QOM casts and rename it to
parent_obj.
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Alex Williamson