prepare_buf should not always grab as many descriptors
as it can, sometimes it should self-limit.
For example, an NCQ transfer of 1 sector with a PRDT that
describes 4GiB of data should not copy 4GiB of data, it
should just transfer that first 512 bytes.
PIO is not affected, because the dma_buf_rw dma helpers
already have a byte limit built-in to them, but DMA/NCQ
will exhaust the entire list regardless of requested size.
AHCI 1.3 specifies in section 6.1.6 Command List Underflow that
NCQ is not required to detect underflow conditions. Non-NCQ
pathways signal underflow by writing to the PRDBC field, which
will already occur by writing the actual transferred byte count
to the PRDBC, signaling the underflow.
Our NCQ pathways aren't required to detect underflow, but since our DMA
backend uses the size of the PRDT to determine the size of the transer,
if our PRDT is bigger than the transaction (the underflow condition) it
doesn't cost us anything to detect it and truncate the PRDT.
This is a recoverable error and is not signaled to the guest, in either
NCQ or normal DMA cases.
For BMDMA, the existing pathways should see no guest-visible difference,
but any bytes described in the overage will no longer be transferred
before indicating to the guest that there was an underflow.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-2-git-send-email-jsnow@redhat.com
Amazingly, we weren't doing this before.
Make sure we migrate the IDEState structure that belongs to
the AHCIDevice.IDEBus structure during migrations.
No version numbering changes because AHCI is not officially
migratable (and we can all see with good reason why) so we
do not impact any official builds by altering the stream and
leaving it at version 1.
This fixes the rerror=stop/werror=stop test case where we wish
to migrate a halted job. Previously, the error code would not
migrate, so even if the job completed successfully, AHCI would
report an error because it would still have the placeholder
error code from initialization time.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-15-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-13-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This moves more common restarting logic to the core IDE code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-10-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Start moving the initial state of the current request to IDEBus, so that
AHCI can use it. The set_unit callback is not used anymore once this is
done.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-9-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With restarts now handled by ide_restart_cb and
the IDEDMAOps.restart_dma() member, remove the old
restart_cb callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-8-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
With BMDMA specific excised from the restart functions,
create a HBA-agnostic restart callback to be shared
between the different HBAs.
Change the callback registered with the vmstate_change
handler to always point to ide_restart_cb instead of
relying on the IDEDMAOps.restart_cb() member.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-7-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A helper is added that registers the IDEDMAOp .restart_cb()
via qemu_add_vm_change_state_handler instead of requiring
each HBA to register the callback themselves.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds the restart_dma callback and adjusts
the ide_restart_dma function to utilize this callback
to call the BMDMA-specific restart code instead of statically
executing BMDMA-specific code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1424708286-16483-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(With the previous atapi_dma flag recovery)
If migration happens between the ATAPI command being written and the
bmdma being started, the DMA is dropped. Eventually the guest times
out and recovers, but that can take many seconds.
(This is rare, on a pingpong reading the CD continuously I hit
this about ~1/30-1/50 migrates)
I don't think we've got enough state to be able to recover safely
at this point, so I throw a 'medium error, no seek complete'
that I'm assuming guests will try and recover from an apparently
dirty CD.
OK, it's a hack, the real solution is probably to push a lot of
ATAPI state into the migration stream, but this is a fix that
works with no stream changes. Tested only on Linux (both RHEL5
(pre-libata) and RHEL7).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
SCSI devices have multiple kinds of queries they need to respond
to, as defined in the "cmd inquiry" section in MMC-6 and SPC-3.
Relevent sections:
MMC-6 revision 2g:
Non-VPD response data and pointer to SPC-3;
Section 6.8 "Inquiry Command"
SPC-3 revision 23:
Inquiry command and error handling:
Section 6.4 "INQUIRY command"
VPD data pages format:
Section 7.6 "Vital product data parameters"
We implement these Vital Product Data queries for SCSI, but not for
ATAPI through IDE. The result is that if you are looking for the WWN
identifier via tools such as sg3_utils, you will be unable to query
our CD/DVD rom device to obtain it.
This patch adds the minimum number of mandatory responses as defined
by SPC-3, which include the "supported pages" response (page 0x00)
and the "Device Identification" response (page 0x83). It also correctly
responds when it receives a request for an illegal page to improve
error output from related tools.
The Device ID page contains an arbitrary list of identification
strings of various formats; the ID strings included in this patch
were chosen to mimic those provided by the libata driver when
emulating this SCSI query (model, serial, and wwn when present.)
Example:
# libata emulated response
[root@localhost ~]# sg_inq --id /dev/sda
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: vendor specific [0x0], code_set: ASCII
associated with the addressed logical unit
vendor specific: QM00001
Designation descriptor number 2, descriptor length: 72
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: ATA
vendor specific: QEMU HARDDISK QM00001
# QEMU generated ATAPI response, with WWN
[root@localhost ~]# sg_inq --id /dev/sr0
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 24
designator_type: vendor specific [0x0], code_set: ASCII
associated with the addressed logical unit
vendor specific: QM00005
Designation descriptor number 2, descriptor length: 72
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: ATA
vendor specific: QEMU DVD-ROM QM00005
Designation descriptor number 3, descriptor length: 12
designator_type: NAA, code_set: Binary
associated with the addressed logical unit
NAA 5, IEEE Company_id: 0xc50
Vendor Specific Identifier: 0x15ea71bb
[0x5000c50015ea71bb]
See also: hw/scsi/scsi-disk.c, scsi_disk_emulate_inquiry()
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This impacts both BMDMA and AHCI HBA interfaces for IDE.
Currently, we confuse the difference between a PRDT having
"0 bytes" and a PRDT having "0 complete sectors."
When we receive an incomplete sector, inconsistent error checking
leads to an infinite loop wherein the call succeeds, but it
didn't give us enough bytes -- leading us to re-call the
DMA chain over and over again. This leads to, in the BMDMA case,
leaked memory for short PRDTs, and infinite loops and resource
usage in the AHCI case.
The .prepare_buf() callback is reworked to return the number of
bytes that it successfully prepared. 0 is a valid, non-error
answer that means the table was empty and described no bytes.
-1 indicates an error.
Our current implementation uses the io_buffer in IDEState to
ultimately describe the size of a prepared scatter-gather list.
Even though the AHCI PRDT/SGList can be as large as 256GiB, the
AHCI command header limits transactions to just 4GiB. ATA8-ACS3,
however, defines the largest transaction to be an LBA48 command
that transfers 65,536 sectors. With a 512 byte sector size, this
is just 32MiB.
Since our current state structures use the int type to describe
the size of the buffer, and this state is migrated as int32, we
are limited to describing 2GiB buffer sizes unless we change the
migration protocol.
For this reason, this patch begins to unify the assertions in the
IDE pathways that the scatter-gather list provided by either the
AHCI PRDT or the PCI BMDMA PRDs can only describe, at a maximum,
2GiB. This should be resilient enough unless we need a sector
size that exceeds 32KiB.
Further, the likelihood of any guest operating system actually
attempting to transfer this much data in a single operation is
very slim.
To this end, the IDEState variables have been updated to more
explicitly clarify our maximum supported size. Callers to the
prepare_buf callback have been reworked to understand the new
return code, and all versions of the prepare_buf callback have
been adjusted accordingly.
Lastly, the ahci_populate_sglist helper, relied upon by the
AHCI implementation of .prepare_buf() as well as the PCI
implementation of the callback have had overflow assertions
added to help make clear the reasonings behind the various
type changes.
[Added %d -> %"PRId64" fix John sent because off_pos changed from int to
int64_t.
--Stefan]
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1414785819-26209-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, DMA read/write operations neglect to update
the byte count after a successful transfer like ATAPI
DMA read or PIO read/write operations do.
We correct this oversight by adding another callback into
the IDEDMAOps structure. The commit callback is called
whenever we are cleaning up a scatter-gather list.
AHCI can register this callback in order to update post-
transfer information such as byte count updates.
We use this callback in AHCI to consolidate where we delete
the SGlist as generated from the PRDT, as well as update the
byte count after the transfer is complete.
The QEMUSGList structure has an init flag added to it in order
to make qemu_sglist_destroy a nop if it is called when
there is no sglist, which simplifies cleanup and error paths.
This patch fixes several AHCI problems, notably Non-NCQ modes
of operation for Windows 7 as well as Hibernate support for Windows 7.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1412204151-18117-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I'll use it with block backends shortly, and the name is going to fit
badly there. It's a block layer thing anyway, not just a block driver
thing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I'll use BlockDriverAIOCB with block backends shortly, and the name is
going to fit badly there. It's a block layer thing anyway, not just a
block driver thing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
AHCI has code to fill in the D2H FIS trigger the IRQ all over the place.
Centralize this in a single cmd_done callback by generalizing the existing
async_cmd_done callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
They are not used by AHCI, and should not be even available there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is now called only after the set_inactive callback. Put the two together.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Make it optional and prepare for the next patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
AHCI couldn't cope with asynchronous commands that aren't doing DMA, it
simply wouldn't complete them. Due to the bug fixed in commit f68ec837,
FLUSH commands would seem to have completed immediately even if they
were still running on the host. After the commit, they would simply hang
and never unset the BSY bit, rendering AHCI unusable on any OS sending
flushes.
This patch adds another callback for the completion of asynchronous
commands. This is what AHCI really wants to use for its command
completion logic rather than an DMA completion callback.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
An IDE bus provided by AHCI can only take a single IDE drive. If you add
a drive as slave, qemu used to accept the command line but the device
wouldn't be actually usable. Catch the situation instead and error out.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Headers in include/exec/ are for the deepest innards of QEMU,
they should almost never be included directly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Many of these should be cleaned up with proper qdev-/QOM-ification.
Right now there are many catch-all headers in include/hw/ARCH depending
on cpu.h, and this makes it necessary to compile these files per-target.
However, fixing this does not belong in these patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While testing q35, which has its cdrom attached to the ahci controller, I found
that the Fedora 17 install would panic on boot. The panic occurs while
squashfs is trying to read from the cdrom. The errors are:
[ 8.622711] SQUASHFS error: xz_dec_run error, data probably corrupt
[ 8.625180] SQUASHFS error: squashfs_read_data failed to read block
0x20be48a
I was also able to produce corrupt data reads using an installed piix based
qemu machine, using 'dd'. I found that the corruptions were only occuring when
then read size was greater than 128k. For example, the following command
results in corrupted reads:
dd if=/dev/sr0 of=/tmp/blah bs=256k iflag=direct
The > 128k size reads exercise a different code path than 128k and below. In
ide_atapi_cmd_read_dma_cb() s->io_buffer_size is capped at 128k. Thus,
ide_atapi_cmd_read_dma_cb() is called a second time when the read is > 128k.
However, ahci_dma_rw_buf() restart the read from offset 0, instead of at 128k.
Thus, resulting in a corrupted read.
To fix this, I've introduced 'io_buffer_offset' field in IDEState to keep
track of the offset. I've also modified ahci_populate_sglist() to take a new
3rd offset argument, so that the sglist is property initialized.
I've tested this patch using 'dd' testing, and Fedora 17 now correctly boots
and installs on q35 with the cdrom ahci controller.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This stuff doesn't belong to block layer, and was put there only
because a better home didn't exist then. Now it does.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This isn't quite orthodox. CHS translation is firmware configuration,
communicated via the RTC's CMOS RAM, not a property of the disk. But
it's best to treat it just like geometry anyway.
Maintain backward compatibility exactly like for geometry: fall back
to DriveInfo's translation, set with -drive trans=...
Bonus: info qtree now shows the translation. Except when it shows
"auto": that's resolved by pc_cmos_init_late(). To be addressed
shortly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Geometry needs to be qdev properties, because it belongs to the
disk's guest part.
Maintain backward compatibility exactly like for serial: fall back to
DriveInfo's geometry, set with -drive cyls=...
Do this only for ide-hd. ide-drive is legacy. ide-cd doesn't have a
geometry.
Bonus: info qtree now shows the geometry.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
PC BIOS setup needs IDE geometry information. Get it directly from
the device model rather than through the block layer. In preparation
of purging geometry from the block layer, which will happen later in
this series.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is far less interesting than it sounds. We simply add an Object to each
BusState and then register the types appropriately. Most of the interesting
refactoring will follow in the next patches.
Since we're changing fundamental type names (BusInfo -> BusClass), it all needs
to convert at once. Fortunately, not a lot of code is affected.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[AF: Made all new bus TypeInfos static const.]
[AF: Made qbus_free() call object_delete(), required {qom,glib}_allocated]
Signed-off-by: Andreas Färber <afaerber@suse.de>
The IDE PIO interface currently uses bdrv_read() to perform reads
synchronously. Synchronous I/O in the vcpu thread is bad because it
prevents the guest from executing code - it makes the guest
unresponsive.
This patch converts IDE PIO to use bdrv_aio_readv(). We simply need to
use the BUSY_STAT status so the guest knows to wait while we are busy.
The only external user of ide_sector_read() is restart behavior on I/O
errors and it is not affected by this change. We still need to restart
I/O in the same way.
Migration is also unaffected if I understand the code correctly. We
continue to use the same transfer function and the BUSY_STAT status
should never be migrated since we flush I/O before migrating device
state.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Tested-by: Richard Davies <richard@arachsys.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Allow the user to specify a disk's World Wide Name.
Linux guests can address disks by their unique World Wide Name number
(e.g. /dev/disk/by-id/wwn-0x5001517959123522). This patch adds support
for assigning a World Wide Name number to a virtual IDE disk.
Cc: kwolf@redhat.com
Signed-off-by: Floris Bos <dev@noc-ps.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Allow the user to override the default disk model name "QEMU HARDDISK".
Some Linux distributions use the /dev/disk/by-id/scsi-SATA_name-of-disk-
model_serial addressing scheme when refering to partitions in /etc/fstab
and elsewhere. This causes problems when starting a disk image taken from
an existing physical server under qemu, because when running under qemu
name-of-disk-model is always "QEMU HARDDISK".
This patch introduces a model=s option which in combination with the
existing serial=s option can be used to fake the disk the operating
system was previously on, allowing the OS to boot properly.
Cc: kwolf@redhat.com
Signed-off-by: Floris Bos <dev@noc-ps.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The definitions in ide/internal.h are duplicates, since ATAPI commands
actually come from SCSI. Use the ones in scsi-defs.h and move the
missing ones there. Two exceptions:
- MODE_PAGE_WRITE_PARMS conflicts with the "flexible disk geometry"
page in scsi-disk.c. It is unused, so pick the latter.
- GPCMD_* is left in ide/internal.h, at least for now.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Today, when notifying a VM state change with vm_state_notify(),
we pass a VMSTOP macro as the 'reason' argument. This is not ideal
because the VMSTOP macros tell why qemu stopped and not exactly
what the current VM state is.
One example to demonstrate this problem is that vm_start() calls
vm_state_notify() with reason=0, which turns out to be VMSTOP_USER.
This commit fixes that by replacing the VMSTOP macros with a proper
state type called RunState.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
It's convenience stuff for block device models, so block.h isn't the
ideal home either, but better than block_int.h.
Permits moving some #include "block_int.h" from device model .h into
.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already track it in BlockDriverState. Just like tray open/close
state, we should track it in the device models instead, because it's
device state.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We already track it in BlockDriverState since commit 4be9762a. As
discussed in that commit's message, we should track it in the device
device models instead, because it's device state.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drop WIN_SRST, it has the same value as WIN_DEVICE_RESET.
Drop unused WIN_RESTORE, it has the same value as WIN_RECAL.
Drop codes that are not implemented and long obsolete: WIN_READ_LONG,
WIN_READ_LONG_ONCE, WIN_WRITE_LONG, WIN_WRITE_LONG_ONCE, WIN_FORMAT
(all obsolete since ATA4), WIN_ACKMEDIACHANGE, WIN_POSTBOOT,
WIN_PREBOOT (obsolete since ATA3), WIN_WRITE_SAME (obsolete since
ATA3, code reused for something else in ACS2), WIN_IDENTIFY_DMA
(obsolete since ATA4).
Drop codes that are not implemented and vendor-specific:
EXABYTE_ENABLE_NEST, DISABLE_SEAGATE.
Drop WIN_INIT, it isn't implemented, its value used to be reserved,
and is used for something else since ATA8.
CFA_IDLEIMMEDIATE isn't specific to CFATA. ACS-2 shows it as a
defined command in ATA-1, -2 and -3. Rename to WIN_IDLEIMMEDIATE2.
Mark vendor specific, retired, and obsolete codes.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
John Snow