This key cleanup step requires to move the IRQ debugging bit from
i8259_set_irq directly to the per-PIC pic_set_irq, to pass the PIC
parameters (I/O base, ELCR address and mask, master/slave mode) as
qdev properties, and to interconnect the PICs with their environment via
GPIO pins.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Introduce a reference to the slave PIC for the few cases we need to
access it without a proper pointer at hand and drop PicState2. We could
even live without slave_pic if we had a better way of modeling the
cascade bus the PICs are attached to (in addition to the ISA bus).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This reflects how real PICs indentify their role (in non-buffered mode):
Pass the state of the /SP input on pic_init and use it instead of
pics_state to differentiate between master and slave mode.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
There is nothing in the i8259 spec that justifies the special
pic_intack_read. At least the Linux PREP kernels configure the PICs
properly so that pic_read_irq returns identical values, and setting
read_reg_select in PIC0 cannot be derived from any special i8259 mode.
So switch ppc_prep to pic_read_irq and drop the now unused PIC code.
CC: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This was probably never used so far: According to the spec, polling
means ack'ing the pending IRQ and setting its corresponding bit in isr.
Moreover, we have to signal a pending IRQ via bit 7 of the returned
value, and we must not return a spurious IRQ if none is pending.
This implements the poll command without the help of pic_poll_read which
is left untouched as pic_intack_read is still using it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This converts pic_update_irq to work against a single PIC instead of the
complete cascade. Along this change, the required update after
pic_set_irq1 is now moved into that function.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The ELCR is actually part of the chipset but we model it here for
simplicity reasons. The PIIX3 clears the ELCR on reset, which was once
broken by 4dbe19e181. Fix this by splitting up pic_init_reset from
pic_reset and clearing the register in the latter.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
MIPS and PPC users of the i8259 output signal expect us to report state
updates also after reset. As no consumer (including the master PIC) can
misinterpret the deassert as an activation event, it is safe to simply
update the IRQ state after reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As we want to move the IRQ update to pic_intack, ordering matters: the
slave ack must be executed before the master ack to avoid missing
further pending slave IRQs.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
If pic_poll_read finds no pending IRQ and return a spurious one instead,
no PIC state is changed, thus we do not need to call pic_update_irq.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As a first step towards more generic master-slave support, remove
parent_irq in favor of a per-PIC output interrupt line. The slave's
line is attached to IRQ2 of the master, but it remains unused for now.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
We are about to call the latter from the former. No functional changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The compiler is smarter in choosing the right optimization.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The master PIC is connected to the LINTIN0 of the APICs. As the APIC
currently does not track the state of that line, we have to ask the PIC
to reinject its IRQ after the CPU picked up an event from the APIC.
This introduces pic_get_output to read the master PIC IRQ line state
without changing it. The APIC uses this function to decide if a PIC IRQ
should be reinjected on apic_update_irq. This reflects better how the
real hardware works.
The patch fixes some failures of the kvm unit tests apic and eventinj by
allowing to enable the proper CPU IRQ deassertion when the guest masks
some pending IRQs at PIC level.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The only non-obvious part is pic_poll_read which used
"addr1 >> 7" to detect whether one referred to either
the master or slave PIC. Instead, test this directly.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
This was done with:
sed -i 's/qemu_get_clock\>/qemu_get_clock_ns/' \
$(git grep -l 'qemu_get_clock\>' )
sed -i 's/qemu_new_timer\>/qemu_new_timer_ns/' \
$(git grep -l 'qemu_new_timer\>' )
after checking that get_clock and new_timer never occur twice
on the same line. There were no missed occurrences; however, even
if there had been, they would have been caught by the compiler.
There was exactly one false positive in qemu_run_timers:
- current_time = qemu_get_clock (clock);
+ current_time = qemu_get_clock_ns (clock);
which is of course not in this patch.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When available, we'd like to be able to access the DeviceState
when registering a savevm. For buses with a get_dev_path()
function, this will allow us to create more unique savevm
id strings.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Instead of calling the IOAPIC from the PIC, raise IOAPIC irqs via the ISA bus.
As a side effect, IOAPIC lines 16-23 are enabled.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
I used the following command to enable debugging:
perl -p -i -e 's/^\/\/#define DEBUG/#define DEBUG/g' * */* */*/*
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This reverts commit 8217606e6e (and
updates later added users of qemu_register_reset), we solved the
problem it originally addressed less invasively.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add the parameter 'order' to qemu_register_reset and sort callbacks on
registration. On system reset, callbacks with lower order will be
invoked before those with higher order. Update all existing users to the
standard order 0.
Note: At least for x86, the existing users seem to assume that handlers
are called in their registration order. Therefore, the patch preserves
this property. If someone feels bored, (s)he could try to identify this
dependency and express it properly on callback registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Refactor the monitor API and prepare it for decoupled terminals:
term_print functions are renamed to monitor_* and all monitor services
gain a new parameter (mon) that will once refer to the monitor instance
the output is supposed to appear on. However, the argument remains
unused for now. All monitor command callbacks are also extended by a mon
parameter so that command handlers are able to pass an appropriate
reference to monitor output services.
For the case that monitor outputs so far happen without clearly
identifiable context, the global variable cur_mon is introduced that
shall once provide a pointer either to the current active monitor (while
processing commands) or to the default one. On the mid or long term,
those use case will be obsoleted so that this variable can be removed
again.
Due to the broad usage of the monitor interface, this patch mostly deals
with converting users of the monitor API. A few of them are already
extended to pass 'mon' from the command handler further down to internal
functions that invoke monitor_printf.
At this chance, monitor-related prototypes are moved from console.h to
a new monitor.h. The same is done for the readline API.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6711 c046a42c-6fe2-441c-8c8c-71466251a162
Jan Kiszka