Place the PBA table at 0x1000, as placed by VMware virtual hardware.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Place device reported PCI capabilities at the same offsets as placed by
the VMware virtual hardware: MSI at [84], MSI-X at [9c].
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
VMXNET3_DEVICE_VERSION is used as return value for accessing
UPT Revision Report and Selection register. So rename it
to VMXNET3_UPT_REVISION.
Signed-off-by: Miao Yan <yanmiaoebest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Return 0 on unknown command, this is what esxi (5.x+) behaves.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
VMXNET3_CMD_GET_DEV_EXTRA_INFO should return 0 for emulation
mode
This behavior can be observed by the following steps:
1) run a Linux distro on esxi server (5.x+)
2) modify vmxnet3 Linux driver to read the register:
VMXNET3_WRITE_BAR1_REG(adapter, VMXNET3_REG_CMD, VMXNET3_CMD_GET_DEV_EXTRA_INFO);
ret = VMXNET3_READ_BAR1_REG(adapter, VMXNET3_REG_CMD);
pr_info("vmxnet3 dev_info: 0x%x\n", ret);
The kernel log will have some like the following message:
[ 7005.111170] vmxnet3 dev_info: 0x0
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
VMXNET3_CMD_GET_DID_LO should return PCI ID of the device
and VMXNET3_CMD_GET_DID_HI should return vmxnet3 revision ID.
This behavior can be observed by the following steps:
1) run a Linux distro on esxi server (5.x+)
2) modify vmxnet3 Linux driver to read DID_HI and DID_LO:
VMXNET3_WRITE_BAR1_REG(adapter, VMXNET3_REG_CMD, VMXNET3_CMD_GET_DID_LO);
lo = VMXNET3_READ_BAR1_REG(adapter, VMXNET3_REG_CMD);
VMXNET3_WRITE_BAR1_REG(adapter, VMXNET3_REG_CMD, VMXNET3_CMD_GET_DID_HI);
high = VMXNET3_READ_BAR1_REG(adapter, VMXNET3_REG_CMD);
pr_info("vmxnet3 DID lo: 0x%x, high: 0x%x\n", lo, high);
The kernel log will have something like the following message:
[ 7005.111170] vmxnet3 DID lo: 0x7b0, high: 0x1
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When reading device status, 0 means device is successfully
activated and 1 means error.
This behavior can be observed by the following steps:
1) run a Linux distro on esxi server (5.5+)
2) modify vmxnet3 Linux driver to give it an invalid
address to 'adapter->shared_pa' which is the
shared memory for guest/host communication
This will trigger device activation failure and kernel
log will have the following message:
[ 7138.403256] vmxnet3 0000:03:00.0 eth1: Failed to activate dev: error 1
So return 1 on device activation failure instead of -1;
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Vmxnet3 device emulator does not check if the device is active
before activating it, also it did not free the transmit & receive
buffers while deactivating the device, thus resulting in memory
leakage on the host. This patch fixes both these issues to avoid
host memory leakage.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Macro VMW_SHPRN(...) is already defined vmxnet3_debug.h,
so remove the duplication
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Vmxnet3 uses the following debug macro style:
#ifdef SOME_DEBUG
# define debug(...) do{ printf(...); } while (0)
# else
# define debug(...) do{ } while (0)
#endif
If SOME_DEBUG is undefined, then format string inside the
debug macro will never be checked by compiler. Code is
likely to break in the future when SOME_DEBUG is enabled
because of lack of testing. This patch changes this
to the following:
#define debug(...) \
do { if (SOME_DEBUG_ENABLED) printf(...); } while (0)
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Use %zu specifier for size_t in printf, otherwise build would fail
on platforms where size_t is not unsigned long
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Macro MAC_FMT and MAC_ARG are not defined, but used in vmxnet3_net_init().
This will cause build error when debug level is raised in
vmxnet3_debug.h (enable all VMXNET3_DEBUG_xxx).
Use VMXNET_MF and VXMNET_MA instead.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
class_size = sizeof(XICSStateClass) does not make much sense
in the RTC code and likely was just a copy-n-paste error.
Let's simply remove it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There's no such thing as "PCI queues" in the virtio core.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If virtio-net driver allocates memory in ivshmem shared memory,
vhost-net will work correctly, but vhost-user will not work because
a fd of shared memory will not be sent to vhost-user backend.
This patch fixes ivshmem to store file descriptor of shared memory.
It will be used when vhost-user negotiates vhost-user backend.
Signed-off-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The 'virtqueue_state' and 'ringsize' can be saved using VMSTATE
macros rather than hand coded .get/.put
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Factor out and expose the function to locate the floppy controller in
the system.
It will allow to dynamically populate the relevant objects in the ACPI
tables.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: qemu-block@nongnu.org
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU now uses internally composed DSDT so drop now
empty *.dsl templates and related *.generated
binary blobs.
Also since templates are not used anymore/obolete
remove utility scripts used for extracting/patching
AML blobs compiled by IASL and for updating them
in git tree.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
leave Scope(\_SB) definition in DSDT so that iasl
would be able to compile DSDT since we are still
need definition block for table.
After Q35 ASL is converted, DSDT templates will
be completly replaced by AML API generated tables.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI routing table for expander buses is build with help
of build_prt() using AML API. And it's almost the same
as PRT for PCI0 bus except of power-management device.
So make existing build_prt() build PRT table for PCI0
bus as well.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
and also move PRQx fields declaration as it can't be
split out into separate patch since fields use
PCI0.ISA.P40C operation region and OperationRegion
must be declared in the same table as a Field that
uses it. If this condition is not statisfied Windows
will BSOD ans IASL (make check) will error out as well.
For the same reason pm is moved together with isa-bridge
as the later refernces P13C OperationRegion from pm device.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
most of MEMORY_foo defines are not shared
with ASL anymore and are used only inside of
memory_hotplug_acpi_table.c, so move them
there and make them strings. As result we
can replace stringify(MEMORY_foo) with just
MEMORY_foo, which makes code a bit cleaner.
No AML change introduced by this patch.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
in addition remove no longer needed acpi-dsdt-mem-hotplug.dsl.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
before consolidating memhp code in memory_hotplug_acpi_table.c
and for simplifying review, first factor out memhp code into
new function build_memory_devices() in i386/acpi-build.c
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
----
PS:
no functional change, only code movement.
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
move remnants of MHPD device from DSDT into SSDT.
i.e. Device(MHPD), _UID, _HID
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The ACPI specification (minimally versions 1.0b through 6.0) define the
FADT.CENTURY field as:
The RTC CMOS RAM index to the century of data value (hundred and
thousand year decimals). If this field contains a zero, then the RTC
centenary feature is not supported. If this field has a non-zero value,
then this field contains an index into RTC RAM space that OSPM can use
to program the centenary field.
The x86 targets generate ACPI payload, emulate an RTC
(CONFIG_MC146818RTC), and that RTC supports the "centenary feature" (see
occurrences of RTC_CENTURY in cmos_ioport_write() and cmos_ioport_read()
in "hw/timer/mc146818rtc.c".)
However, FADT.CENTURY is left at zero currently:
[06Ch 0108 1] RTC Century Index : 00
which -- according to analysis done by Ruiyu Ni at Intel -- should cause
Linux and Windows 8+ to think the RTC centenary feature is unavailable,
and cause Windows 7 to (incorrectly) assume that the offset to use is
constant 0x32. (0x32 happens to be the right value on QEMU, but Windows 7
is wrong to assume anything at all).
Exposing the right nonzero offset in FADT.CENTURY informs Linux and
Windows 8+ about the right capabilities of the hardware, plus it retrofits
our FADT to Windows 7's behavior.
Regression tested with the following guests (all UEFI installs):
- i386 Q35: Fedora 21 ("Fedlet" edition)
- x86_64:
- i440fx:
- Fedora 21
- RHEL 6 and 7
- Windows 7 and 10
- Windows Server 2008 R2 and 2012 R2
- Q35:
- Fedora 22
- Windows 8.1
Cc: "Michael S. Tsirkin" <mst@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Igor Mammedov <imammedo@redhat.com> (supporter:ACPI/SMBIOS)
Cc: Paolo Bonzini <pbonzini@redhat.com> (maintainer:X86)
Cc: Richard Henderson <rth@twiddle.net> (maintainer:X86)
Cc: Eduardo Habkost <ehabkost@redhat.com> (maintainer:X86)
Cc: Ruiyu Ni <ruiyu.ni@intel.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Fix the bug introduced by 595a4f07: function host_pci_config_read() should be
pass-by-reference, not value.
This probably means this function never worked for anyone.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the current nvdimm_build_nfit(), the pointer 'header' initially equals
to table_data->data + table_data->len. However, the following
g_array_append_vals(table_data, structures->data, structures->len)
may resize and relocate table_data->data[]. Therefore, the usage of 'header'
afterwards may be illegal.
This patch fixes this issue by storing an offset within table_data->data[]
(rather than an address) in 'header'.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Current text_console_update() writes totally broken color attributes
to console_write_ch(). The format now is writing,
[WRONG]
bold << 21 | fg << 12 | bg << 8 | char
fg == 3bits curses color number
bg == 3bits curses color number
I can't see this format is where come from. Anyway, this doesn't work
at all.
What curses expects is actually (and vga.c is using),
[RIGHT]
bold << 21 | bg << 11 | fg << 8 | char
fg == 3bits vga color number
bg == 3bits vga color number
And curses set COLOR_PAIR() up to match this format, and curses's
chtype. I.e,
bold | color_pair | char
color_pair == (bg << 3 | fg)
To fix, this simply uses VGA color number everywhere except curses.c
internal. Then, convert it to above [RIGHT] format to write by
console_write_ch(). And as bonus, this reduces to expose curses define
to other parts (removes COLOR_* from console.c).
[Tested the first line is displayed as white on blue back for monitor
in curses console]
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Message-id: 87r3j95407.fsf@mail.parknet.co.jp
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Now that file only contains generic code.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
The new function resides in virtio specific file.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Move out generic definitions from virtio-9p.h to 9p.h. Fix header
inclusions.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Factor out v9fs_iov_v{,un}marshal. Implement pdu_{,un}marshal with those
functions.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
This matches naming convention of pdu_marshal and pdu_unmarshal.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
V9fsState can be referenced by pdu->s. Initialise that in device
realization function.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
And rename v9fs_marshal to v9fs_iov_marshal, v9fs_unmarshal to
v9fs_iov_unmarshal.
The rationale behind this change is that, this marshalling interface is
used both by virtio and proxy helper. Renaming files and functions to
reflect the true nature of this interface.
Xen transport is going to have its own marshalling interface.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
On overcommitted CPU, kernel can be so slow that an interrupt can
be triggered by the device whereas the driver is not ready to receive
it. This drives us into an infinite loop.
On suspend, if a SOF interrupt is raised between the stop of the
device processing and the change of the device internal state to
OHCI_USB_SUSPEND (QEMU stops SOF timer on this state change), this
interrupt is never acknowledged.
This patch clears pending SOF interrupt on OHCI_USB_SUSPEND setting.
Some details:
- ohci_irq(): the OHCI interrupt handler, acknowledges the SOF IRQ
only if the state of the driver (rh_state) is OHCI_STATE_RUNNING.
So if this interrupt happens and the driver is not in this state,
the function is called again and again, moving the system to a
CPU starvation.
- ohci_rh_suspend(): the function stop the operation and acknowledge
pending interrupts (but doesn't disable it). Later in the function,
the device is moved to OHCI_SUSPEND_STATE, and the driver to
OHCI_RH_SUSPENDED. If between the moment when the interrupt is
acknowledged and the moment when the device is suspended a new
interrupt is raised, it will be never acknowledged because the
driver is now not in OHCI_RH_RUNNING state.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 1452109525-32150-3-git-send-email-lvivier@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
On overcommitted CPU, kernel can be so slow that an interrupt can
be triggered by the device whereas the driver is not ready to receive
it. This drives us into an infinite loop.
This does not happen on real hardware because real hardware never send
interrupt immediately after the controller has been moved to OPERATION state.
This patch tries to delay the first SOF interrupt to let driver exits from
the critical section (which is not protected against interrupts...)
Some details:
- ohci_irq(): the OHCI interrupt handler, acknowledges the SOF IRQ
only if the state of the driver (rh_state) is OHCI_STATE_RUNNING.
So if this interrupt happens and the driver is not in this state,
the function is called again and again, moving the system to a
CPU starvation.
- ohci_rh_resume(): the driver re-enables operation with OHCI_USB_OPER.
In QEMU this start the SOF timer and QEMU starts to send IRQs. As
the driver is not in OHCI_STATE_RUNNING and not protected against IRQ,
the ohci_irq() can be called and the driver never moved to
OHCI_STATE_RUNNING.
Suggested-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 1452109525-32150-2-git-send-email-lvivier@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
trace_usb_mtp_inotify_event() was being called after the object was
being freed.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 1450861787-16213-3-git-send-email-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb_mtp_inotify_cleanup uses QLIST_FOREACH to pick events
from a list and free them which is incorrect. Use QLIST_FOREACH_SAFE
instead.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 1450861787-16213-2-git-send-email-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Specification says that: "This bit is set by HCD to initiate a software reset of HC."
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 1450567431-31795-4-git-send-email-hpoussin@reactos.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Specification says that, when entering this state, "the contents of the registers
(except Root Hub registers) are preserved by the HC. [...] The Root Hub is being reset,
which causes the Root Hub's downstream ports to be reset and possibly powered off."
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-id: 1450567431-31795-3-git-send-email-hpoussin@reactos.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Some structures in virtio-9p.h have been unused since 2011 when relevant
functions switched to use coroutines.
The declaration of pdu_packunpack and function do_pdu_unpack are
useless.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
The deleted file only contained V9fsConf which wasn't virtio specific.
Merge that to the general header of 9pfs.
Fixed header inclusions as I went along.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
These three files are not virtio specific. Rename them to generic
names.
Fix comments and header inclusion in various files.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
These two files are not virtio specific. Rename them to use generic
names.
Fix includes in various C files. Change define guards and comments
in header files.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Those two files are not virtio specific. Rename them to use generic
names.
Fix includes in various C files. Change define guards and comments
in header files.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
This file is not virtio specific. Rename it to use generic name.
Fix comment and remove unneeded inclusion of virtio.h.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
This file is not virtio specific. Rename it to use generic name.
Fix comment and remove unneeded inclusion of virtio.h.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
This file is not virtio specific. Rename it to use generic name.
Fix comment and remove unneeded inclusion of virtio.h.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Those two files are not virtio specific. Rename them to use generic
names.
Fix includes in various C files. Change define guards and comments in
header files.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
It's necessary to distinguish source and target before we can add
blockdev-mirror, because we would want a concrete type of operation to
check on target bs before starting.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 1450932306-13717-2-git-send-email-famz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Set the MicroBlaze CPU version to 8.10.a avoiding a runtime
warning due to an unset CPU version.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Set the MicroBlaze CPU version to 7.10.d avoiding a runtime
warning due to an unset CPU version.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Accesses to the timer register high bit should only set NPT, whilst accesses
to the timer compare register high bit should only set INT_DIS. This fixes
issues with the timer being unexpectedly disabled whilst trying to boot
FreeBSD SPARC64.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-By: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently there is confusion between use of these bits for the timer and timer
compare registers (while they both have the same value, the behaviour is
different). Split into two separate CPUTimer fields so we can always reference
the correct value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-By: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlZ6ffwACgkQAvw66wEB28L59wCdEbXdeiE8SPV4rI/PIdvnUtAX
BmAAn2MPJ07PcUXmu3jaj1ZEmjoEGJ+R
=DucP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
Fix a 2.5 regression.
# gpg: Signature made Wed 23 Dec 2015 10:57:00 GMT using DSA key ID 0101DBC2
# gpg: Good signature from "Greg Kurz <gkurz@fr.ibm.com>"
# gpg: aka "Greg Kurz <groug@free.fr>"
# gpg: aka "Greg Kurz <gkurz@linux.vnet.ibm.com>"
# gpg: aka "Gregory Kurz (Groug) <groug@free.fr>"
# gpg: aka "Gregory Kurz (Cimai Technology) <gkurz@cimai.com>"
# gpg: aka "Gregory Kurz (Meiosys Technology) <gkurz@meiosys.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2BD4 3B44 535E C0A7 9894 DBA2 02FC 3AEB 0101 DBC2
* remotes/gkurz/tags/for-upstream:
virtio-9p: use accessor to get thread_pool
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pxb support for q35
nvdimm support
most of ipmi support
part of DSDT rewrite
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWeX6WAAoJECgfDbjSjVRp08kH/0YwnLl23evSIst67O5AthCm
IjTu7tbANtpadMq9YxU7Is+6QEi27C26pqy4CWgoirhsrjiY2jC5LVCZqhIhBEeJ
JFyAiYglJDMraHWyKG373lLEeQvNmEmFsxmULmV6cX2j1tsgyXCqdQs5DmRGnHno
L02W0p3EnEfUwYvnuyeuKmdw+ykiCxKt5zBYodSU6yPkFI34Ex/VBiwqt6nJ0hU1
xDNbmudN0GI/ckUezq0ko6AXPnmouiq0QPGVf0EXRaFQxwjbyb+f9zK+xmo/v2k3
5Mz3+otQ8i5cyunY9ziQf58WKMXY/CmerXXv4/gnfwz6EfdZZGsNc1niJcsXxDs=
=D7er
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, pc features
pxb support for q35
nvdimm support
most of ipmi support
part of DSDT rewrite
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 22 Dec 2015 16:47:18 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (55 commits)
acpi: extend aml_and() to accept target argument
acpi: extend aml_or() to accept target argument
acpi add aml_dma()
acpi: add aml_to_buffer()
acpi: add aml_to_hexstring()
acpi: extend aml_field() to support LockRule
acpi: add aml_lgreater()
acpi: add aml_lor()
acpi: add aml_sleep()
acpi: add aml_alias()
acpi: extend aml_shiftright() to accept target argument
acpi: add aml_to_integer()
acpi: add aml_call0() helper
acpi: add aml_decrement() and aml_subtract()
acpi: extend aml_add() to accept target argument
acpi: aml: add helper for Opcode Arg2 Arg2 [Dst] AML pattern
acpi: add aml_create_qword_field()
acpi: add aml_mutex(), aml_acquire(), aml_release()
acpi: add aml_lgreater_equal()
acpi: add aml_sizeof
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The aio_context_new() function does not allocate a thread pool. This is
deferred to the first call to the aio_get_thread_pool() accessor. It is
hence forbidden to access the thread_pool field directly, as it may be
NULL. The accessor *must* be used always.
Fixes: ebac1202c9
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: qemu-stable@nongnu.org
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
it allows to express ShiftRight(A,B,C) syntax
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
it will help to call a method with 0 arguments
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
it allows to express following ASL expression:
Add(arg1, arg2, result)
usecases that do not need to store result
should pass NULL as 3rd arg that would express
Add(arg1, arg2,)
construct.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Currently AML API doesn't compose terms in form of
following pattern:
Opcode Arg2 Arg2 [Dst]
but ASL used in piix4/q35 DSDT ACPI tables uses that
form, so for clean conversion of it, AML API should
be able to handle an optional 'Dst' argumet used there.
Since above pattern is used by arithmetic/bit ops,
introduce helper that they could reuse.
It reduces code duplication in existing 5 aml_foo()
functions and also will prevent more duplication
when exiting functions are extended to support
optional 'Dst' argument.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Implement SizeOf term which is used by NVDIMM _DSM method in later patch
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement DeRefOf term which is used by NVDIMM _DSM method in later patch
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
NVDIMM devices is defined in ACPI 6.0 9.20 NVDIMM Devices
There is a root device under \_SB and specified NVDIMM devices are under the
root device. Each NVDIMM device has _ADR which returns its handle used to
associate MEMDEV structure in NFIT
Currently, we do not support any function on _DSM, that means, NVDIMM
label data has not been supported yet
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
NFIT is defined in ACPI 6.0: 5.2.25 NVDIMM Firmware Interface Table (NFIT)
Currently, we only support PMEM mode. Each device has 3 structures:
- SPA structure, defines the PMEM region info
- MEM DEV structure, it has the @handle which is used to associate specified
ACPI NVDIMM device we will introduce in later patch.
Also we can happily ignored the memory device's interleave, the real
nvdimm hardware access is hidden behind host
- DCR structure, it defines vendor ID used to associate specified vendor
nvdimm driver. Since we only implement PMEM mode this time, Command
window and Data window are not needed
The NVDIMM functionality is controlled by the parameter, 'nvdimm', which
is introduced for the machine, there is a example to enable it:
-machine pc,nvdimm -m 8G,maxmem=100G,slots=100 -object \
memory-backend-file,id=mem1,share,mem-path=/tmp/nvdimm1,size=10G -device \
nvdimm,memdev=mem1,id=nv1
It is disabled on default
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Let build_header() support specified OEM table id so that we can build
multiple SSDT later
If the oem table id is not specified (aka, NULL), we use the default id
instead as the previous behavior
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce "nvdimm" device which is based on pc-dimm device type
Currently, nothing is specific for nvdimm but hotplug is disabled
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add pc-i440fx-2.6 and pc-q35-2.6 machine classes.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Remove the redundant 'alias = NULL' and 'is_default = 0' lines
from older machine-types. pc_*_2_4_machine_options() already
clear those fields, so they don't need to be cleared by
pc_*_2_3_machine_options().
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Only old machine types which don't use the acpi builder (qemu 1.7 + older)
have to load that file for proper acpi support.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allow the IPMI interface to request a forced power off.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a way for IPMI devices to register their firmware information
with the IPMI subsystem so that various firmware entities can pull
that information later for adding to firmware tables.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This provides the simulation of the BT hardware interface for
IPMI.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This provides the simulation of the KCS hardware interface.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds an interface for IPMI that connects to a remote
BMC over a chardev (generally a TCP socket). The OpenIPMI
lanserv simulator describes this interface, see that for
interface details.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This provides a minimal local BMC, basically enough to comply with the
spec and provide a complete watchdog timer (including a sensor, SDR,
and event).
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add the basic IPMI types and infrastructure to QEMU. Low-level
interfaces and simulation interfaces will register with this; it's
kind of the go-between to tie them together.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The field is not used for anything.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>