Implement the missing registers for the TZ MPC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-3-peter.maydell@linaro.org
Implement the Arm TrustZone Memory Protection Controller, which sits
in front of RAM and allows secure software to configure it to either
pass through or reject transactions.
We implement the MPC as a QEMU IOMMU, which will direct transactions
either through to the devices and memory behind it or to a special
"never works" AddressSpace if they are blocked.
This initial commit implements the skeleton of the device:
* it always permits accesses
* it doesn't implement most of the registers
* it doesn't implement the interrupt or other behaviour
for blocked transactions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-2-peter.maydell@linaro.org
With this patch, virt-3.0 machine uses a new 256MB ECAM region
by default instead of the legacy 16MB one, if highmem is set
(LPAE supported by the guest) and (!firmware_loaded || aarch64).
Indeed aarch32 mode FW may not support this high ECAM region.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-11-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch defines a new ECAM region located after the 256GB limit.
The virt machine state is augmented with a new highmem_ecam field
which guards the usage of this new ECAM region instead of the legacy
16MB one. With the highmem ECAM region, up to 256 PCIe buses can be
used.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-9-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allows the creation of a GICv3 node with 1 or 2
redistributor regions depending on the number of smu_cpus.
The second redistributor region is located just after the
existing RAM region, at 256GB and contains up to up to 512 vcpus.
Please refer to kernel documentation for further node details:
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-6-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To prepare for multiple redistributor regions, we introduce
an array of uint32_t properties that stores the redistributor
count of each redistributor region.
Non accelerated VGICv3 only supports a single redistributor region.
The capacity of all redist regions is checked against the number of
vcpus.
Machvirt is updated to set those properties, ie. a single
redistributor region with count set to the number of vcpus
capped by 123.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-4-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The way we used to handle KVM allowable guest pagesizes for PAPR guests
required some convoluted checking of memory attached to the guest.
The allowable pagesizes advertised to the guest cpus depended on the memory
which was attached at boot, but then we needed to ensure that any memory
later hotplugged didn't change which pagesizes were allowed.
Now that we have an explicit machine option to control the allowable
maximum pagesize we can simplify this. We just check all memory backends
against that declared pagesize. We check base and cold-plugged memory at
reset time, and hotplugged memory at pre_plug() time.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The way the POWER Hash Page Table (HPT) MMU is virtualized by KVM HV means
that every page that the guest puts in the pagetables must be truly
physically contiguous, not just GPA-contiguous. In effect this means that
an HPT guest can't use any pagesizes greater than the host page size used
to back its memory.
At present we handle this by changing what we advertise to the guest based
on the backing pagesizes. This is pretty bad, because it means the guest
sees a different environment depending on what should be host configuration
details.
As a start on fixing this, we add a new capability parameter to the
pseries machine type which gives the maximum allowed pagesizes for an
HPT guest. For now we just create and validate the parameter without
making it do anything.
For backwards compatibility, on older machine types we set it to the max
available page size for the host. For the 3.0 machine type, we fix it to
16, the intention being to only allow HPT pagesizes up to 64kiB by default
in future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
As well as being able to generate its own i2c transactions, the ppc4xx
i2c controller has a DIRECTCNTL register which allows explicit control
of the i2c lines.
Using this register an OS can directly bitbang i2c operations. In
order to let emulated i2c devices respond to this, we need to wire up
the DIRECTCNTL register to qemu's bitbanged i2c handling code.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We don't emulate slave mode so related registers are not needed.
[lh]sadr are only retained to avoid too many warnings and simplify
debugging but sdata is not even correct because device has a 4 byte
FIFO instead so just remove this unimplemented register for now.
The intr register is also not implemented correctly, it is for
diagnostics and normally not even visible on device without explicitly
enabling it. As no guests are known to need this remove it as well.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_irq_alloc_block and spapr_irq_alloc() are now deprecated.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, when a device requests for IRQ number in a sPAPR machine, the
spapr_irq_alloc() routine first scans the ICSState status array to
find an empty slot and then performs the assignement of the selected
numbers. Split this sequence in two distinct routines : spapr_irq_find()
for lookups and spapr_irq_claim() for claiming the IRQ numbers.
This will ease the introduction of a static layout of IRQ numbers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr capabilities have an apply hook to actually activate (or deactivate)
the feature in the system at reset time. However, a number of capabilities
affect the setup of cpus, and need to be applied to each of them -
including hotplugged cpus for extra complication. To make this simpler,
add an optional cpu_apply hook that is called from spapr_cpu_reset().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Previously, the effective values of the various spapr capability flags
were only determined at machine reset time. That was a lazy way of making
sure it was after cpu initialization so it could use the cpu object to
inform the defaults.
But we've now improved the compat checking code so that we don't need to
instantiate the cpus to use it. That lets us move the resolution of the
capability defaults much earlier.
This is going to be necessary for some future capabilities.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
It introduces a base PnvChip class from which the specific processor
chip classes, Pnv8Chip and Pnv9Chip, inherit. Each of them needs to
define an init and a realize routine which will create the controllers
of the target processor. For the moment, the base PnvChip class
handles the XSCOM bus and the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A per-CPU machine data pointer was recently added to PowerPCCPU. The
motivation is to to hide platform specific details from the core CPU
code. This per-CPU data can hold state which is relevant to the guest
though, eg, Virtual Processor Areas, and we should migrate this state.
This patch adds the plumbing so that we can migrate the per-CPU data
for PAPR guests. We only do this for newer machine types for the sake
of backward compatibility. No state is migrated for the moment: the
vmstate_spapr_cpu_state structure will be populated by subsequent
patches.
Signed-off-by: Greg Kurz <groug@kaod.org>
[dwg: Fix some trivial spelling and spacing errors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This moves the details of the ISA bus creation under the LPC model but
more important, the new PnvChip operation will let us choose the chip
class to use when we introduce the different chip classes for Power9
and Power8. It hides away the processor chip controllers from the
machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On Power9, the thread interrupt presenter has a different type and is
linked to the chip owning the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The boot framebuffer is expected to be configured by the firmware, so it
uses fw_cfg as interface. Initialization goes as follows:
(1) Check whenever etc/ramfb is present.
(2) Allocate framebuffer from RAM.
(3) Fill struct RAMFBCfg, write it to etc/ramfb.
Done. You can write stuff to the framebuffer now, and it should appear
automagically on the screen.
Note that this isn't very efficient because it does a full display
update on each refresh. No dirty tracking. Dirty tracking would have
to be active for the whole ram slot, so that wouldn't be very efficient
either. For a boot display which is active for a short time only this
isn't a big deal. As permanent guest display something better should be
used (if possible).
This is the ramfb core code. Some windup is needed for display devices
which want have a ramfb boot display.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20180613122948.18149-2-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
CPUPPCState currently contains a number of fields containing the state of
the VPA. The VPA is a PAPR specific concept covering several guest/host
shared memory areas used to communicate some information with the
hypervisor.
As a PAPR concept this is really machine specific information, although it
is per-cpu, so it doesn't really belong in the core CPU state structure.
There's also other information that's per-cpu, but platform/machine
specific. So create a (void *)machine_data in PowerPCCPU which can be
used by the machine to locate per-cpu data. Intialization, lifetime and
cleanup of machine_data is entirely up to the machine type.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Currently, we allocate space for all the cpu objects within a single core
in one big block. This was copied from an older version of the spapr code
and requires some ugly pointer manipulation to extract the individual
objects.
This design was due to a misunderstanding of qemu lifetime conventions and
has already been changed in spapr (in 94ad93bd "spapr_cpu_core: instantiate
CPUs separately".
Make an equivalent change in pnv_core to get rid of the nasty pointer
arithmetic.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
In the case where we have an interrupt generated externally from inputs to
bits 1 and 2 of port A and/or port B, it is necessary to expose
mos6522_update_irq() so it can be called by the interrupt source.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PMU device supercedes the CUDA device found on older New World Macs and
is supported by a larger number of guest OSs from OS 9 to OS X 10.5.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
MacOS 9 has a bug in its PMU driver whereby after configuring the ADB bus
devices it sends another write to reg 3 on both devices resetting them
both back to the same address.
Add a new disable_direct_reg3_writes property to ADBDevice to disable these
direct writes which can enabled just for the upcoming pmu-adb support.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PMU-enabled New World Macs expose their GPIOs via a separate memory region
within the macio device.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This option allows the VIA configuration to be controlled between 3
different possible setups: cuda, pmu-adb and pmu with USB rather than ADB
keyboard/mouse.
For the moment we don't do anything with the configuration except to pass
it to the macio device (the via-cuda parent) and also to the firmware via
the fw_cfg interface so that it can present the correct device tree.
The default is cuda which is the current default and so will have no
change in behaviour.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- Fix options that work only with -drive or -blockdev, but not with
both, because of QDict type confusion
- rbd: Add options 'auth-client-required' and 'key-secret'
- Remove deprecated -drive options serial/addr/cyls/heads/secs/trans
- rbd, iscsi: Remove deprecated 'filename' option
- Fix 'qemu-img map' crash with unaligned image size
- Improve QMP documentation for jobs
-----BEGIN PGP SIGNATURE-----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=LxgF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- Fix options that work only with -drive or -blockdev, but not with
both, because of QDict type confusion
- rbd: Add options 'auth-client-required' and 'key-secret'
- Remove deprecated -drive options serial/addr/cyls/heads/secs/trans
- rbd, iscsi: Remove deprecated 'filename' option
- Fix 'qemu-img map' crash with unaligned image size
- Improve QMP documentation for jobs
# gpg: Signature made Fri 15 Jun 2018 15:20:03 BST
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (26 commits)
block: Remove dead deprecation warning code
block: Remove deprecated -drive option serial
block: Remove deprecated -drive option addr
block: Remove deprecated -drive geometry options
rbd: New parameter key-secret
rbd: New parameter auth-client-required
block: Fix -blockdev / blockdev-add for empty objects and arrays
check-block-qdict: Cover flattening of empty lists and dictionaries
check-block-qdict: Rename qdict_flatten()'s variables for clarity
block-qdict: Simplify qdict_is_list() some
block-qdict: Clean up qdict_crumple() a bit
block-qdict: Tweak qdict_flatten_qdict(), qdict_flatten_qlist()
block-qdict: Simplify qdict_flatten_qdict()
block: Make remaining uses of qobject input visitor more robust
block: Factor out qobject_input_visitor_new_flat_confused()
block: Clean up a misuse of qobject_to() in .bdrv_co_create_opts()
block: Fix -drive for certain non-string scalars
block: Fix -blockdev for certain non-string scalars
qobject: Move block-specific qdict code to block-qdict.c
block: Add block-specific QDict header
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For the IoTKit MPC support, we need to wire together the
interrupt outputs of 17 MPCs; this exceeds the current
value of MAX_OR_LINES. Increase MAX_OR_LINES to 32 (which
should be enough for anyone).
The tricky part is retaining the migration compatibility for
existing OR gates; we add a subsection which is only used
for larger OR gates, and define it such that we can freely
increase MAX_OR_LINES in future (or even move to a dynamically
allocated levels[] array without an upper size limit) without
breaking compatibility.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180604152941.20374-10-peter.maydell@linaro.org
Remove the now-unused armv7m_init() function. This was a legacy from
before we properly QOMified ARMv7M, and it has some flaws:
* it combines work that needs to be done by an SoC object (creating
and initializing the TYPE_ARMV7M object) with work that needs to
be done by the board model (setting the system up to load the ELF
file specified with -kernel)
* TYPE_ARMV7M creation failure is fatal, but an SoC object wants to
arrange to propagate the failure outward
* it uses allocate-and-create via qdev_create() whereas the current
preferred style for SoC objects is to do creation in-place
Board and SoC models can instead do the two jobs this function
was doing themselves, in the right places and with whatever their
preferred style/error handling is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20180601144328.23817-3-peter.maydell@linaro.org
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Here's another batch of ppc patches towards the 3.0 release. There's
a fair bit here, because I've been working through my mail backlog
after a holiday. There's not much of a central theme, amongst other
things we have:
* ppc440 / sam460ex improvements
* logging and error cleanups
* 40p (PReP) bugfixes
* Macintosh fixes and cleanups
* Add emulation of the new POWER9 store-forwarding barrier
instruction variant
* Hotplug cleanups
-----BEGIN PGP SIGNATURE-----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=g3bP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.0-20180612' into staging
ppc patch queue 2018-06-12
Here's another batch of ppc patches towards the 3.0 release. There's
a fair bit here, because I've been working through my mail backlog
after a holiday. There's not much of a central theme, amongst other
things we have:
* ppc440 / sam460ex improvements
* logging and error cleanups
* 40p (PReP) bugfixes
* Macintosh fixes and cleanups
* Add emulation of the new POWER9 store-forwarding barrier
instruction variant
* Hotplug cleanups
# gpg: Signature made Tue 12 Jun 2018 07:43:21 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.0-20180612: (33 commits)
spapr_pci: Remove unhelpful pagesize warning
xics_kvm: use KVM helpers
ppc/pnv: fix LPC HC firmware address space
spapr: handle cpu core unplug via hotplug handler chain
spapr: handle pc-dimm unplug via hotplug handler chain
spapr: introduce machine unplug handler
spapr: move memory hotplug support check into spapr_memory_pre_plug()
spapr: move lookup of the node into spapr_memory_plug()
spapr: no need to verify the node
target/ppc: Allow PIR read in privileged mode
ppc4xx_i2c: Clean up and improve error logging
target/ppc: extend eieio for POWER9
mos6522: convert VMSTATE_TIMER_PTR_TEST to VMSTATE_TIMER_PTR
mos6522: move timer frequency initialisation to mos6522_reset
cuda: embed mos6522_cuda device directly rather than using QOM object link
mos6522: fix vmstate_mos6522_timer version in vmstate_mos6522
ppc: add missing FW_CFG_PPC_NVRAM_FLAT definition
ppc: remove obsolete macio_init() definition from mac.h
ppc: remove obsolete pci_pmac_init() definitions from mac.h
hw/misc/mos6522: Add trailing '\n' to qemu_log() calls
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A specific MemoryRegion is required for the LPC HC Firmware address
space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 6522 VIA timer frequency cannot be set by altering registers within the
device itself and hence it is a fixed property of the machine.
Move the initialisation of the timer frequency to the mos6522 reset function
and ensure that any subclasses always call the parent reset function so that
it isn't required to store the timer frequency within vmstate_mos6522_timer
itself.
By moving the frequency initialisation to the device reset function then we
find that the realize function for both mos6522 and mos6522_cuda becomes
obsolete and can simply be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Examining the migration stream it can be seen that the mos6522 device state is
being stored separately rather than as part of the CUDA device which is
incorrect (and likely to cause issues if another mos6522 device is added to
the machine).
Resolve this by embedding the mos6522_cuda device directly within the CUDA
device rather than using a QOM object link to reference the device separately.
Note that we also bump the version in vmstate_cuda to reflect this change: this
isn't particularly important for the moment as the Mac machine migration isn't
100% reliable due to issues migrating the timebase under TCG.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is used in OpenBIOS to define the memory layout of the NVRAM device. Whilst
currently left at its default value, add the missing definition to ensure it is
reserved.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
>From observation of various OS sources it can be seen that the token register
introduced in 4e46dcdbd3 "PPC: Newworld: Add uninorth token register" is not
required, since the only register currently implemented is the uninorth hardware
version which is read-only.
Remove the token register implementation and instead return the uninorth
version corresponding to the hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace the "nvdimm-cap" option which took numeric arguments such as "2"
with a more user friendly "nvdimm-persistence" option which takes symbolic
arguments "cpu" or "mem-ctrl".
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For the case where the end_transfer_func is also the caller of
ide_transfer_start, the mutual recursion can lead to unlimited
stack usage. Introduce a new version that can be used to change
tail recursion into a loop, and use it in trace_ide_atapi_cmd_reply_end.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-8-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Now that end_transfer_func is a tail call in ahci_start_transfer,
formalize the fact that the callback (of which ahci_start_transfer is
the sole implementation) takes care of the transfer too: rename it to
pio_transfer and, if it is present, call the end_transfer_func as soon
as it returns.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-4-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of this commit, the Spec v1 is not working, and all controllers
expect the cards to be conformant to Spec v2.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The maximum frame size includes the CRC and depends if a VLAN tag is
inserted or not. Adjust the frame size limit in the transmit handler
using on the FTGMAC100State buffer size and in the receive handler use
the packet protocol.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530061711.23673-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Specs are available here :
https://www.nxp.com/docs/en/application-note/AN264.pdf
This is a simple model supporting the basic registers for led and GPIO
mode. The device also supports two blinking rates but not the model
yet.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is an helper routine to add a single EEPROM on an I2C bus. It can
be directly used by smbus_eeprom_init() which adds a certain number of
EEPROMs on mips and x86 machines.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While we skip the GIC_INTERNAL irqs, we don't change the register offset
accordingly. This will overlap the GICR registers value and leave the
last GIC_INTERNAL irq's registers out of update.
Fix this by skipping the registers banked by GICR.
Also for migration compatibility if the migration source (old version
qemu) doesn't send gicd_no_migration_shift_bug = 1 to destination, then
we shift the data of PPI to get the right data for SPI.
Fixes: 367b9f527b
Cc: qemu-stable@nongnu.org
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Message-id: 1527816987-16108-1-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This macro isn't used by any VFIO code. And its name is
too generic. The vfio-common.h (in include/hw/vfio) can
be included by other modules in QEMU. It can introduce
conflicts.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU 3.0 enables strict check for compression & decompression to
make the migration more robust, that depends on the source to fix
the internal design which triggers the unexpected error conditions
To make it work for migrating old version QEMU to 2.13 QEMU, we
introduce this parameter to disable the error check on the
destination which is the default behavior of the machine type
which is older than 2.13, alternately, the strict check can be
enabled explicitly as followings:
-M pc-q35-2.11 -global migration.decompress-error-check=true
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Read only feature shouldn't be negotiable, because if the
backend device reported Read only feature supported, QEMU
host driver shouldn't change backend's RO attribute. While
here, also enable the vhost-user-blk test utility to test
RO feature.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a machine command line option to allow the user to control the Platform
Capabilities Structure in the virtualized NFIT. This Platform Capabilities
Structure was added in ACPI 6.2 Errata A.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since no devices use it, we can safely remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-5-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Removal of DeviceClass::init() moved from previous patch, missing
documentation updates supplied]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-5-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I2CSlaveClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-3-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-3-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SMBusDeviceClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-2-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-2-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 5643cc94ac ("virtio-gpu-3d: add support for second capability
set (v4)") updated virtio_gpu.h with a define that does not yet(?)
exist upstream resulting in build breakage every time Linux headers
are updated via the standard update script. Conditionally define this
within QEMU code instead to avoid future breakage.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Fixes: 5643cc94ac ("virtio-gpu-3d: add support for second capability set (v4)")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180525132755.21839-2-peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-22-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-17-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Xen 4.11 has a new API to directly map guest resources. Among the resources
that can be mapped using this API are ioreq pages.
This patch modifies QEMU to attempt to use the new API should it exist,
falling back to the previous mechanism if it is unavailable.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
No declaration of "hw/vfio/vfio-common.h" directly requires to include
the "exec/address-spaces.h" header. To simplify dependencies and
ease the upcoming cleanup of "exec/address-spaces.h", directly include
it in the source file where the declaration are used.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-2-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch introduces VHOST_USER_PROTOCOL_F_HOST_NOTIFIER.
With this feature negotiated, vhost-user backend can register
memory region based host notifiers. And it will allow the guest
driver in the VM to notify the hardware accelerator at the
vhost-user backend directly.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When multi queue is enabled e.g. for a virtio-net device,
each queue pair will have a vhost_dev, and the only thing
shared between vhost devs currently is the chardev. This
patch introduces a vhost-user state structure which will
be shared by all vhost devs of the same virtio device.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces a vhost op for vhost backends to allow
them to filter the memory sections that they can handle.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Beginning of merging vDPA, new PCI ID, a new virtio balloon stat, intel
iommu rework fixing a couple of security problems (no CVEs yet), fixes
all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbBX2cAAoJECgfDbjSjVRpOEYIAIR6KGkwbAJ9SnO9B71DQHl1
yYYgM7i2HwyZ1YPnXOYWnI1lzQ1bARTf2krQJFGmfjlDaueFf9KnXdNByoVCmG8m
UhF/rQp3DcJ4wTABktPtME8gWdQxKPmDxlN5W3f29Zrm3g9S+Hshi+sfPZUkBxL4
gQMFRctb2SxvQXG+lusHVwo1oF6pzGZMmX35906he3m4xS/cfoeCP7Qj6nSvHZq7
lsLoOeYxHtXWA9gTYxpd7zW+hhUxkspoOqcXySHfO7e5enJANaulTxKuC0T+6HL4
O2iUM+1wjUYE0tQcNJ6x7emA82k5OdG2OMD6gbR1oSdquttJo7+4R+goqpb44rc=
=NUoY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio, vhost: fixes, features
Beginning of merging vDPA, new PCI ID, a new virtio balloon stat, intel
iommu rework fixing a couple of security problems (no CVEs yet), fixes
all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 23 May 2018 15:41:32 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (28 commits)
intel-iommu: rework the page walk logic
util: implement simple iova tree
intel-iommu: trace domain id during page walk
intel-iommu: pass in address space when page walk
intel-iommu: introduce vtd_page_walk_info
intel-iommu: only do page walk for MAP notifiers
intel-iommu: add iommu lock
intel-iommu: remove IntelIOMMUNotifierNode
intel-iommu: send PSI always even if across PDEs
nvdimm: fix typo in label-size definition
contrib/vhost-user-blk: enable protocol feature for vhost-user-blk
hw/virtio: Fix brace Werror with clang 6.0.0
libvhost-user: Send messages with no data
vhost-user+postcopy: Use qemu_set_nonblock
virtio: support setting memory region based host notifier
vhost-user: support receiving file descriptors in slave_read
vhost-user: add Net prefix to internal state structure
linux-headers: add kvm header for mips
linux-headers: add unistd.h on all arches
update-linux-headers.sh: unistd.h, kvm consistency
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+YI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/sstabellini-http/tags/xen-20180522-tag' into staging
Xen 2018/05/22
# gpg: Signature made Tue 22 May 2018 19:44:06 BST
# gpg: using RSA key 894F8F4870E1AE90
# gpg: Good signature from "Stefano Stabellini <stefano.stabellini@eu.citrix.com>"
# gpg: aka "Stefano Stabellini <sstabellini@kernel.org>"
# Primary key fingerprint: D04E 33AB A51F 67BA 07D3 0AEA 894F 8F48 70E1 AE90
* remotes/sstabellini-http/tags/xen-20180522-tag:
xen_disk: be consistent with use of xendev and blkdev->xendev
xen_disk: use a single entry iovec
xen_backend: make the xen_feature_grant_copy flag private
xen_disk: remove use of grant map/unmap
xen_backend: add an emulation of grant copy
xen: remove other open-coded use of libxengnttab
xen_disk: remove open-coded use of libxengnttab
xen_backend: add grant table helpers
xen: add a meaningful declaration of grant_copy_segment into xen_common.h
checkpatch: generalize xen handle matching in the list of types
xen-hvm: create separate function for ioreq server initialization
xen_pt: Present the size of 64 bit BARs correctly
configure: Add explanation for --enable-xen-pci-passthrough
xen/pt: use address_space_memory object for memory region hooks
xen-pvdevice: Introduce a simplistic xen-pvdevice save state
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a new header file, move the bochs vbe dispi interface
defines to it, so they can be used outside vga code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180522165058.15404-2-kraxel@redhat.com
This patch fixes a potential small window that the DMA page table might
be incomplete or invalid when the guest sends domain/context
invalidations to a device. This can cause random DMA errors for
assigned devices.
This is a major change to the VT-d shadow page walking logic. It
includes but is not limited to:
- For each VTDAddressSpace, now we maintain what IOVA ranges we have
mapped and what we have not. With that information, now we only send
MAP or UNMAP when necessary. Say, we don't send MAP notifies if we
know we have already mapped the range, meanwhile we don't send UNMAP
notifies if we know we never mapped the range at all.
- Introduce vtd_sync_shadow_page_table[_range] APIs so that we can call
in any places to resync the shadow page table for a device.
- When we receive domain/context invalidation, we should not really run
the replay logic, instead we use the new sync shadow page table API to
resync the whole shadow page table without unmapping the whole
region. After this change, we'll only do the page walk once for each
domain invalidations (before this, it can be multiple, depending on
number of notifiers per address space).
While at it, the page walking logic is also refactored to be simpler.
CC: QEMU Stable <qemu-stable@nongnu.org>
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Tested-by: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For UNMAP-only IOMMU notifiers, we don't need to walk the page tables.
Fasten that procedure by skipping the page table walk. That should
boost performance for UNMAP-only notifiers like vhost.
CC: QEMU Stable <qemu-stable@nongnu.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SECURITY IMPLICATION: this patch fixes a potential race when multiple
threads access the IOMMU IOTLB cache.
Add a per-iommu big lock to protect IOMMU status. Currently the only
thing to be protected is the IOTLB/context cache, since that can be
accessed even without BQL, e.g., in IO dataplane.
Note that we don't need to protect device page tables since that's fully
controlled by the guest kernel. However there is still possibility that
malicious drivers will program the device to not obey the rule. In that
case QEMU can't really do anything useful, instead the guest itself will
be responsible for all uncertainties.
CC: QEMU Stable <qemu-stable@nongnu.org>
Reported-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
That is not really necessary. Removing that node struct and put the
list entry directly into VTDAddressSpace. It simplfies the code a lot.
Since at it, rename the old notifiers_list into vtd_as_with_notifiers.
CC: QEMU Stable <qemu-stable@nongnu.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Fixes: commit da6789c27c ("nvdimm: add a macro for property "label-size"")
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Cc: Haozhong Zhang <haozhong.zhang@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces the support for setting memory region
based host notifiers for virtio device. This is helpful when
using a hardware accelerator for a virtio device, because
hardware heavily depends on the notification, this will allow
the guest driver in the VM to notify the hardware directly.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no longer any use of this flag outside of the xen_backend code.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
This patch adds grant table helper functions to the xen_backend code to
localize error reporting and use of xen_domid.
The patch also defers the call to xengnttab_open() until just before the
initialise method in XenDevOps is invoked. This method is responsible for
mapping the shared ring. No prior method requires access to the grant table.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Currently the xen_disk source has to carry #ifdef exclusions to compile
against Xen older then 4.8. This is a bit messy so this patch lifts the
definition of struct xengnttab_grant_copy_segment and adds it into the
pre-4.8 compat area in xen_common.h, which allows xen_disk to be cleaned
up.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
There is no need to include pci.h in these files.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The ZynqMP contains two instances of a generic DMA, the GDMA, located in the
FPD (full power domain), and the ADMA, located in LPD (low power domain). This
patch adds these two DMAs to the ZynqMP board.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180503214201.29082-3-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the generic DMA found on Xilinx ZynqMP.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180503214201.29082-2-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The property legacy-cache will be used to control the cache information.
If user passes "-cpu legacy-cache" then older information will
be displayed even if the hardware supports new information. Otherwise
use the statically loaded cache definitions if available.
Renamed the previous cache structures to legacy_*. If there is any change in
the cache information, then it needs to be initialized in builtin_x86_defs.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Message-Id: <20180514164156.27034-3-babu.moger@amd.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This fixes an issue by adding bounds checking to multi-byte packets
where the PS/2 mouse data stream may become corrupted due to data being
discarded when the PS/2 ringbuffer is full.
Interrupts for Multi-byte responses are postponed until the final byte
has been queued.
These changes fix a bug where windows guests drop the mouse device
entirely requring the guest to be restarted.
Signed-off-by: Geoffrey McRae <geoff@hostfission.com>
Message-Id: <20180507150310.2FEA0381924@moya.office.hostfission.com>
[ kraxel: codestyle fixes ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Calling pause_all_vcpus()/resume_all_vcpus() from a VCPU thread might
not be the best idea. As pause_all_vcpus() temporarily drops the qemu
mutex, two parallel calls to pause_all_vcpus() can be active at a time,
resulting in a deadlock. (either by two VCPUs or by the main thread and a
VCPU)
Let's handle it via the main loop instead, as suggested by Paolo. If we
would have two parallel reset requests by two different VCPUs at the
same time, the last one would win.
We use the existing ipl device to handle it. The nice side effect is
that we can get rid of reipl_requested.
This change implies that all reset handling now goes via the common
path, so "no-reboot" handling is now active for all kinds of reboots.
Let's execute any CPU initialization code on the target CPU using
run_on_cpu.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180424101859.10239-1-david@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJa+UAZAAoJEO8Ells5jWIRTJIIAIcpNROupxHEfcAQKU7lIqys
qx/FxKp+lknzzQMwUfmZwT3PuBD+tWuE7ugXgzjVulvE11F+Z3QBPTDBtOObaMa1
qpgIF3zzrNxtuWMc/72Q8/wEE1wtBUo+WTAGw9Xp1dVomYOOsg1wa7dsKdZhRfz7
nIwDW2ftw3/mx+uTW2/a163v+IDDL9L+HOLibQHWUxOMM39ASchiqAXLF4mfhpwH
xr0OPd7wtcmrDsD/CLbdkGCJ/+vsXnY8pzNmy1RjJuDpWpqlgYpJJPtLBfXBo9VA
91sz5+KryzjpXXzKcQuhiU020O1dIKIe3PWqK6z0x0UjtZ1Yox5adZ3eFomHHwU=
=bIws
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 14 May 2018 08:51:53 BST
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net: Get rid of 'vlan' terminology and use 'hub' instead in the doc files
net: Get rid of 'vlan' terminology and use 'hub' instead in the source files
net: Remove the deprecated "vlan" parameter
net: Fix memory leak in net_param_nic()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It's been marked as deprecated since QEMU v2.9.0, so that should have
been enough time for everybody to either just drop unnecessary "vlan=0"
parameters, to switch to the modern -device + -netdev syntax for connecting
guest NICs with host network backends, or to switch to the "hubport" netdev
in case hubs are really wanted instead.
Buglink: https://bugs.launchpad.net/qemu/+bug/658904
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
load_dtb() depends on arm_load_kernel() to figure out place
in RAM where it should be loaded, but it's not required for
arm_load_kernel() to work. Sometimes it's neccesary for
devices added with -device/device_add to be enumerated in
DTB as well, which's lead to [1] and surrounding commits to
add 2 more machine_done notifiers with non obvious ordering
to make dynamic sysbus devices initialization happen in
the right order.
However instead of moving whole arm_load_kernel() in to
machine_done, it's sufficient to move only load_dtb() into
virt_machine_done() notifier and remove ArmLoadKernelNotifier/
/PlatformBusFDTNotifierParams notifiers, which saves us ~90LOC
and simplifies code flow quite a bit.
Later would allow to consolidate DTB generation within one
function for 'mach-virt' board and make it reentrant so it
could generate updated DTB in device hotplug secenarios.
While at it rename load_dtb() to arm_load_dtb() since it's
public now.
Add additional field skip_dtb_autoload to struct arm_boot_info
to allow manual DTB load later in mach-virt and to avoid touching
all other boards to explicitly call arm_load_dtb().
1) (ac9d32e hw/arm/boot: arm_load_kernel implemented as a machine init done notifier)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1525691524-32265-4-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
platform-bus were using machine_done notifier to get and map
(assign irq/mmio resources) dynamically added sysbus devices
after all '-device' options had been processed.
That however creates non obvious dependencies on ordering of
machine_done notifiers and requires carefull line juggling
to keep it working. For example see comment above
create_platform_bus() and 'straitforward' arm_load_kernel()
had to converted to machine_done notifier and that lead to
yet another machine_done notifier to keep it working
arm_register_platform_bus_fdt_creator().
Instead of hiding resource assignment in platform-bus-device
to magically initialize sysbus devices, use device plug
callback and assign resources explicitly at board level
at the moment each -device option is being processed.
That adds a bunch of machine declaration boiler plate to
e500plat board, similar to ARM/x86 but gets rid of hidden
machine_done notifier and would allow to remove the dependent
notifiers in ARM code simplifying it and making code flow
easier to follow.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 1525691524-32265-3-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By default MachineClass::get_hotplug_handler is NULL and concrete board
should set it to it's own handler.
Considering there isn't any default handler, drop saving empty
MachineClass::get_hotplug_handler in child class and make PC code
consistent with spapr/s390x boards.
We can bring this back when actual usecase surfaces and do it
consistently across boards that use get_hotplug_handler().
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 1525691524-32265-2-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* pc-dimm: factor out MemoryDevice
(virtio-pmem and virtio-mem will make use of the new abstraction later)
* scripts/device-crash-test: Removed fixed CAN entries
-----BEGIN PGP SIGNATURE-----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=Hhge
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/machine-next-pull-request' into staging
Machine queue, 2018-05-07
* pc-dimm: factor out MemoryDevice
(virtio-pmem and virtio-mem will make use of the new abstraction later)
* scripts/device-crash-test: Removed fixed CAN entries
# gpg: Signature made Mon 07 May 2018 18:01:42 BST
# gpg: using RSA key 2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/machine-next-pull-request:
scripts/device-crash-test: Removed fixed CAN entries
vl: allow 'maxmem' without 'slot'
spapr: rename "hotplug memory" terminology to "device memory"
pc: rename "hotplug memory" terminology to "device memory"
machine: rename MemoryHotplugState to DeviceMemoryState
pc-dimm: move actual plug/unplug of a memory region to MemoryDevice
pc-dimm: factor out capacity and slot checks into MemoryDevice
pc-dimm: factor out address search into MemoryDevice code
pc-dimm: pass in the machine and to the MemoryHotplugState
pc-dimm: no need to pass the memory region
machine: make MemoryHotplugState accessible via the machine
pc-dimm: factor out MemoryDevice interface
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Several code cleanups, minor specification conformance changes,
fixes to make ROM read-only and add device-tree size checks.
* Honour privileged ISA v1.10 counter enable CSRs.
* Implements WARL behavior for CSRs that don't support writes
* Past behavior of raising traps was non-conformant
with the RISC-V Privileged ISA Specification v1.10.
* Allow S-mode access to sstatus.MXR when priv ISA >= v1.10
* Sets mtval/stval to zero on exceptions without addresses
* Past behavior of leaving the last value was non-conformant
with the RISC-V Privileged ISA Specition v1.10. mtval/stval
must be set on all exceptions; to zero if not supported.
* Make ROMs read-only and implement device-tree size checks
* Uses memory_region_init_rom and rom_add_blob_fixed_as
* Adds hexidecimal instruction bytes to disassembly output.
* Fixes missing break statement for rv128 disassembly.
* Several code cleanups
* Replacing hard-coded constants with enums
* Dead-code elimination
This is an incremental pull that contains 20 reviewed changes out
of 38 changes currently queued in the qemu-2.13-for-upstream branch.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQR8mZMOsXzYugc9Xvpr8dezV+8+TwUCWu496QAKCRBr8dezV+8+
T1ZEAJ4wQRHZtn4suN5yMEHQMA2FkX1iNACgiYWLtcNcgoa88eaTcJJJu4QZryY=
=I2wf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riscv/tags/riscv-qemu-2.13-pull-20180506' into staging
RISC-V: QEMU 2.13 Privileged ISA emulation updates
Several code cleanups, minor specification conformance changes,
fixes to make ROM read-only and add device-tree size checks.
* Honour privileged ISA v1.10 counter enable CSRs.
* Implements WARL behavior for CSRs that don't support writes
* Past behavior of raising traps was non-conformant
with the RISC-V Privileged ISA Specification v1.10.
* Allow S-mode access to sstatus.MXR when priv ISA >= v1.10
* Sets mtval/stval to zero on exceptions without addresses
* Past behavior of leaving the last value was non-conformant
with the RISC-V Privileged ISA Specition v1.10. mtval/stval
must be set on all exceptions; to zero if not supported.
* Make ROMs read-only and implement device-tree size checks
* Uses memory_region_init_rom and rom_add_blob_fixed_as
* Adds hexidecimal instruction bytes to disassembly output.
* Fixes missing break statement for rv128 disassembly.
* Several code cleanups
* Replacing hard-coded constants with enums
* Dead-code elimination
This is an incremental pull that contains 20 reviewed changes out
of 38 changes currently queued in the qemu-2.13-for-upstream branch.
# gpg: Signature made Sun 06 May 2018 00:27:37 BST
# gpg: using DSA key 6BF1D7B357EF3E4F
# gpg: Good signature from "Michael Clark <michaeljclark@mac.com>"
# gpg: aka "Michael Clark <mjc@sifive.com>"
# gpg: aka "Michael Clark <michael@metaparadigm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 7C99 930E B17C D8BA 073D 5EFA 6BF1 D7B3 57EF 3E4F
* remotes/riscv/tags/riscv-qemu-2.13-pull-20180506:
RISC-V: Mark ROM read-only after copying in code
RISC-V: No traps on writes to misa,minstret,mcycle
RISC-V: Make mtvec/stvec ignore vectored traps
RISC-V: Add mcycle/minstret support for -icount auto
RISC-V: Use [ms]counteren CSRs when priv ISA >= v1.10
RISC-V: Allow S-mode mxr access when priv ISA >= v1.10
RISC-V: Clear mtval/stval on exceptions without info
RISC-V: Hardwire satp to 0 for no-mmu case
RISC-V: Update E and I extension order
RISC-V: Remove erroneous comment from translate.c
RISC-V: Remove EM_RISCV ELF_MACHINE indirection
RISC-V: Make virt header comment title consistent
RISC-V: Make some header guards more specific
RISC-V: Fix missing break statement in disassembler
RISC-V: Include instruction hex in disassembly
RISC-V: Remove unused class definitions
RISC-V: Remove identity_translate from load_elf
RISC-V: Use ROM base address and size from memmap
RISC-V: Make virt board description match spike
RISC-V: Replace hardcoded constants with enum values
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's make it clear at relevant places that we are dealing with device
memory. That it can be used for memory hotplug is just a special case.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-11-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
[ehabkost: rebased series, solved conflicts at spapr.c]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Let's make it clear that we are dealing with device memory. That it can
be used for memory hotplug is just a special case.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-10-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename it to better match the new terminology.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-9-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Registering the memory region for migration has do be done by the owner.
There could be cases, where we don't want to migrate the memory.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-8-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the checks into memory_device_get_free_addr(). This will check
before doing any calculations if we have KVM/vhost slots left and if
the total region size would be exceeded.
Of course, while at it, make it independent of pc-dimm code.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-7-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This mainly moves code, but does a handfull of optimizations:
- We pass the machine instead of the address space properties
- We check the hinted address directly and handle fragmented memory
better
- We make the search independent of pc-dimm
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-6-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We use the machine internally either way, so let's just pass it in then.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-5-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We can just query it ourselves. When unplugging, we should always be
able to the region (as it was previously plugged). E.g. PPC already
assumed that and used &error_abort.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-4-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Let's allow to query the MemoryHotplugState directly from the machine.
If the pointer is NULL, the machine does not support memory devices. If
the pointer is !NULL, the machine supports memory devices and the
data structure contains information about the applicable physical
guest address space region.
This allows us to generically detect if a certain machine has support
for memory devices, and to generically manage it (find free address
range, plug/unplug a memory region).
We will rename "MemoryHotplugState" to something more meaningful
("DeviceMemory") after we completed factoring out the pc-dimm code into
MemoryDevice code.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-3-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
[ehabkost: rebased series, solved conflicts at spapr.c]
[ehabkost: squashed fix to use g_malloc0()]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
On the qmp level, we already have the concept of memory devices:
"query-memory-devices"
Right now, we only support NVDIMM and PCDIMM.
We want to map other devices later into the address space of the guest.
Such device could e.g. be virtio devices. These devices will have a
guest memory range assigned but won't be exposed via e.g. ACPI. We want
to make them look like memory device, but not glued to pc-dimm.
Especially, it will not always be possible to have TYPE_PC_DIMM as a parent
class (e.g. virtio devices). Let's use an interface instead. As a first
part, convert handling of
- qmp_pc_dimm_device_list
- get_plugged_memory_size
to our new model. plug/unplug stuff etc. will follow later.
A memory device will have to provide the following functions:
- get_addr(): Necessary, as the property "addr" can e.g. not be used for
virtio devices (already defined).
- get_plugged_size(): The amount this device offers to the guest as of
now.
- get_region_size(): Because this can later on be bigger than the
plugged size.
- fill_device_info(): Fill MemoryDeviceInfo, e.g. for qmp.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-2-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Removes a whole lot of unnecessary boilerplate code. Machines
don't need to be objects. The expansion of the SOC object model
for the RISC-V machines will happen in the future as SiFive
plans to add their FE310 and FU540 SOCs to QEMU. However, it
seems that this present boilerplate is complete unnecessary.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Another case of replacing hard coded constants, this time
referring to the definition in the virt machine's memmap.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V device-tree code has a number of hard-coded
constants and this change moves them into header enums.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
This patch builds the smmuv3 node in the ACPI IORT table.
The RID space of the root complex, which spans 0x0-0x10000
maps to streamid space 0x0-0x10000 in smmuv3, which in turn
maps to deviceid space 0x0-0x10000 in the ITS group.
The guest must feature the IOMMU probe deferral series
(https://lkml.org/lkml/2017/4/10/214) which fixes streamid
multiple lookup. This bug is not related to the SMMU emulation.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Message-id: 1524665762-31355-14-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add code to instantiate an smmuv3 in virt machine. A new iommu
integer member is introduced in VirtMachineState to store the type
of the iommu in use.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-13-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements a skeleton for the smmuv3 device.
Datatypes and register definitions are introduced. The MMIO
region, the interrupts and the queue are initialized.
Only the MMIO read operation is implemented here.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the page table walk for VMSAv8-64.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Message-id: 1524665762-31355-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We set up the infrastructure to enumerate all the PCI devices
attached to the SMMU and create an associated IOMMU memory
region and address space.
Those info are stored in SMMUDevice objects. The devices are
grouped according to the PCIBus they belong to. A hash table
indexed by the PCIBus pointer is used. Also an array indexed by
the bus number allows to find the list of SMMUDevices.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The patch introduces the smmu base device and class for the ARM
smmu. Devices for specific versions will be derived from this
base device.
We also introduce some important datatypes.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- new machine type
- extend SCLP event masks
- support configuration of consoles via -serial
- firmware improvements: non-sequential entries in boot menu, support
for indirect loading via .INS files in s390-netboot
- bugfixes and cleanups
-----BEGIN PGP SIGNATURE-----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=cYvD
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20180504' into staging
First s390x pull request for 2.13.
- new machine type
- extend SCLP event masks
- support configuration of consoles via -serial
- firmware improvements: non-sequential entries in boot menu, support
for indirect loading via .INS files in s390-netboot
- bugfixes and cleanups
# gpg: Signature made Fri 04 May 2018 08:19:57 BST
# gpg: using RSA key DECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cohuck@redhat.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20180504:
pc-bios/s390: Update firmware images
s390-ccw: force diag 308 subcode to unsigned long
pc-bios/s390-ccw/net: Add support for .INS config files
pc-bios/s390-ccw/net: Use diag308 to reset machine before jumping to the OS
pc-bios/s390-ccw/net: Split up net_load() into init, load and release parts
pc-bios/s390-ccw: fix non-sequential boot entries (enum)
pc-bios/s390-ccw: fix non-sequential boot entries (eckd)
pc-bios/s390-ccw: fix loadparm initialization and int conversion
pc-bios/s390-ccw: rename MAX_TABLE_ENTRIES to MAX_BOOT_ENTRIES
pc-bios/s390-ccw: size_t should be unsigned
hw/s390x: Allow to configure the consoles with the "-serial" parameter
s390x/kvm: cleanup calls to cpu_synchronize_state()
vfio-ccw: introduce vfio_ccw_get_device()
s390x/sclp: extend SCLP event masks to 64 bits
s390x: introduce 2.13 compat machine
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since the macio device has a link to the PIC device, we can now wire up the
IRQs directly via qdev GPIOs rather than having to use an intermediate array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 4e46dcdbd3 "PPC: Newworld: Add uninorth token register" added a TODO
which was to convert the uninorth registers hack to a proper device. Move
these registers to a new uninorth device, removing the old hacks from
mac_newworld.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Under PAPR, only the boot CPU is active when the system starts. Other cpus
must be explicitly activated using an RTAS call. The entry state for the
boot and secondary cpus isn't identical, but it has some things in common.
We're going to add a bit more common setup later, too, so to simplify
make a helper which sets up the common entry state for both boot and
secondary cpu threads.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The consoles ("sclpconsole" and "sclplmconsole") can only be configured
with "-device" and "-chardev" so far. Other machines use the convenience
option "-serial" to configure the default consoles, even for virtual
consoles like spapr-vty on the pseries machine. So let's support this
option on s390x, too. This way we can easily enable the serial console
here again with "-nodefaults", for example:
qemu-system-s390x -no-shutdown -nographic -nodefaults -serial mon:stdio
... which is way shorter than typing:
qemu-system-s390x -no-shutdown -nographic -nodefaults \
-chardev stdio,id=c1,mux=on -device sclpconsole,chardev=c1 \
-mon chardev=c1
The -serial parameter can also be used if you only want to see the QEMU
monitor on stdio without using -nodefaults, but not the console output.
That's something that is pretty impossible with the current code today:
qemu-system-s390x -no-shutdown -nographic -serial none
While we're at it, this patch also maps the second -serial option to the
"sclplmconsole", so that there is now an easy way to configure this second
console on s390x, too, for example:
qemu-system-s390x -no-shutdown -nographic -serial null -serial mon:stdio
Additionally, the new code is also smaller than the old one and we have
less s390x-specific code in vl.c :-)
I've also checked that migration still works as expected by migrating
a guest with console output back and forth between a qemu-system-s390x
that has this patch and an instance without this patch.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1524754794-28005-1-git-send-email-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Extend the SCLP event masks to 64 bits.
Notice that using any of the new bits results in a state that cannot be
migrated to an older version.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Message-Id: <1520507069-22179-1-git-send-email-imbrenda@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The new property ibm,dynamic-memory-v2 allows memory to be represented
in a more compact manner in device tree.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As a rule we prefer to pass PowerPCCPU instead of CPUPPCState, and this
change will make some things simpler later on.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The existing UNINState actually represents the PCI/AGP host bridge stage so
rename it accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Do this for both the uninorth main and uninorth u3 AGP buses, using the main
PCI bus for each machine (this ensures the IO addresses still match those
used by OpenBIOS).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that the OpenPIC is wired up via the board, we can now remove our temporary
PIC qdev pointer property and replace it with an object link instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is in preparation for moving the PCI bus wiring inside the uninorth
host bridge devices. In the future it will be possible to remove this once the
PICs have been switched to use qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since the macio device has a link to the PIC device, we can now wire up the
IRQs directly via qdev GPIOs rather than having to use an intermediate array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead wire up heathrow to the CPU and grackle PCI host using qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
[dwg: Added hw/hw.h #include as suggested by Philippe Mathieu-Daudé]
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The last user was just removed; remove this function, accordingly.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Xen unstable (to be in 4.11) has two new dmops, relocate_memory and
pin_memory_cacheattr. Use these to set up the VGA memory, replacing the
previous calls to libxc. This allows the VGA console to work properly
when QEMU is running restricted (-xen-domid-restrict).
Wrapper functions are provided to allow QEMU to work with older versions
of Xen.
Tweak the error handling while making this change:
* Report pin_memory_cacheattr errors.
* Report errors even when DEBUG_HVM is not set. This is useful for
trying to understand why VGA is not working, since otherwise it just
fails silently.
* Fix the return values when an error occurs. The functions now
consistently return -1 and set errno.
CC: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
xc_interface_open etc. is not going to work if we have dropped
privilege, but xendevicemodel_shutdown will if everything is new
enough.
xendevicemodel_shutdown is only availabe in Xen 4.10 and later, so
provide a stub for earlier versions.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
We are going to want to use the dummy xendevicemodel_handle type in
new stub functions in the CONFIG_XEN_CTRL_INTERFACE_VERSION < 41000
section. So we need to provide that definition, or (as applicable)
include the appropriate header, earlier in the file.
(Ideally the newer compatibility layers would be at the bottom of the
file, so that they can naturally benefit from the compatibility layers
for earlier version. But that's rather too much for this series.)
No functional change.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
And insist that it works.
Drop individual use of xendevicemodel_restrict and
xenforeignmemory_restrict. These are not actually effective in this
version of qemu, because qemu has a large number of fds open onto
various Xen control devices.
The restriction arrangements are still not right, because the
restriction needs to be done very late - after qemu has opened all of
its control fds.
xentoolcore_restrict_all and xentoolcore.h are available in Xen 4.10
and later, only. Provide a compatibility stub. And drop the
compatibility stubs for the old functions.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
The superio device has a limit on the number of serial
ports it supports which is really only there because
it has a fixed-size array serial[]. This limit isn't
related particularly to the global MAX_SERIAL_PORTS limit,
so use a different #define for it.
(In practice the users of superio only ever want 2 serial ports.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-12-peter.maydell@linaro.org
The ISA serial port handling in serial-isa.c imposes a limit
of 4 serial ports. This is because we only know of 4 IO port
and IRQ settings for them, and is unrelated to the generic
MAX_SERIAL_PORTS limit, though they happen to both be set at
4 currently.
Use a new MAX_ISA_SERIAL_PORTS wherever that is the correct
limit to be checking against.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-11-peter.maydell@linaro.org
Turn the newly added subsection off for old machine types
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We would like to have different behavior for passthrough devices
depending on the SCSI version they expose. To prepare for that,
allow the user of emulated devices to specify the desired SCSI
level, and adjust the emulation according to the property value.
The next patch will set the level for scsi-block and scsi-generic
devices.
Based on a patch by Daniel Henrique Barboza
<danielhb@linux.vnet.ibm.com>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of using "1.0" as the system version of SMBIOS, we should use
mc->name for mach-virt machine type to be consistent other architectures.
With this patch, "dmidecode -t 1" (e.g., "-M virt-2.12,accel=kvm") will
show:
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: QEMU
Product Name: KVM Virtual Machine
Version: virt-2.12
Serial Number: Not Specified
...
instead of:
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: QEMU
Product Name: KVM Virtual Machine
Version: 1.0
Serial Number: Not Specified
...
For backward compatibility, we allow older machine types to keep "1.0"
as the default system version.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20180322212318.7182-1-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux does not detect a break from this IMX serial driver as a magic
sysrq. Nor does it note a break in the port error counts.
The former is because the Linux driver uses the BRCD bit in the USR2
register to trigger the RS-232 break handler in the kernel, which is
where sysrq hooks in. The emulated UART was not setting this status
bit.
The latter is because the Linux driver expects, in addition to the BRK
bit, that the ERR bit is set when a break is read in the FIFO. A break
should also count as a frame error, so add that bit too.
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Message-id: 20180320013657.25038-1-tpiepho@impinj.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make qmp_pc_dimm_device_list() return sorted by start address
list of devices so that it could be reused in places that
would need sorted list*. Reuse existing pc_dimm_built_list()
to get sorted list.
While at it hide recursive callbacks from callers, so that:
qmp_pc_dimm_device_list(qdev_get_machine(), &list);
could be replaced with simpler:
list = qmp_pc_dimm_device_list();
* follow up patch will use it in build_srat()
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> for ppc part
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All PCI devices are now QOM'ified.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The bcm2837 is pretty similar to the bcm2836, but it does have
some differences. Notably, the MPIDR affinity aff1 values it
sets for the CPUs are 0x0, rather than the 0xf that the bcm2836
uses, and if this is wrong Linux will not boot.
Rather than trying to have one device with properties that
configure it differently for the two cases, create two
separate QOM devices for the two SoCs. We use the same approach
as hw/arm/aspeed_soc.c and share code and have a data table
that might differ per-SoC. For the moment the two types don't
actually have different behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-7-peter.maydell@linaro.org
Our BCM2836 type is really a generic one that can be any of
the bcm283x family. Rename it accordingly. We change only
the names which are visible via the header file to the
rest of the QEMU code, leaving private function names
in bcm2836.c as they are.
This is a preliminary to making bcm283x be an abstract
parent class to specific types for the bcm2836 and bcm2837.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-6-peter.maydell@linaro.org
Add support for "TX complete"/TXDC interrupt generate by real HW since
it is needed to support guests other than Linux.
Based on the patch by Bill Paul as found here:
https://bugs.launchpad.net/qemu/+bug/1753314
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: Bill Paul <wpaul@windriver.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Bill Paul <wpaul@windriver.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Message-id: 20180315191141.6789-2-andrew.smirnov@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell