Emulation of the block limits VPD page called back into scsi-disk.c,
which however expected the request to be for a SCSIDiskState and
accessed a scsi-generic device outside the bounds of its struct
(namely to retrieve s->max_unmap_size and s->max_io_size).
To avoid this, move the emulation code to a separate function that
takes a new SCSIBlockLimits struct and marshals it into the VPD
response format.
Reported-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A device can report an excessive number of VPD pages when asked for a
list; this can cause an out-of-bounds access to buf in
scsi_generic_set_vpd_bl_emulation. It should not happen, but
it is technically not incorrect so handle it: do not check any byte
past the allocation length that was sent to the INQUIRY command.
Reported-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Block limits emulation is just placing 0xb0 as the final byte of the
VPD pages list. However, VPD page numbers must be sorted, so change
that to an in-place insert. Since I couldn't find any disk that triggered
the loop more than once, this was tested by adding manually 0xb1
at the end of the list and checking that 0xb0 was added before.
Reported-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While writing a message in 'lsi_do_msgin', message length value
in 'msg_len' could be invalid due to an invalid migration stream.
Add an assertion to avoid an out of bounds access, and reject
the incoming migration data if it contains an invalid message
length.
Discovered by Deja vu Security. Reported by Oracle.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <20181026194314.18663-1-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are 3 virtqueues (ctrl, event and cmd) for virtio scsi device,
but seabios will only set the physical address for the 3rd one (cmd).
Then in vhost_virtqueue_start(), virtio_queue_get_desc_addr()
will be 0 for ctrl and event vq.
In this case, ctrl and event vq are not initialized.
vhost_verify_ring_mappings may use uninitialized vhost_virtqueue
such that vhost_verify_ring_part_mapping returns ENOMEM.
When encountered this problem, we got the following logs:
qemu-system-x86_64: Unable to map available ring for ring 0
qemu-system-x86_64: Verify ring failure on region 0
Signed-off-by: Forrest Liu <forrestl@synology.com>
Signed-off-by: yuchenlin <yuchenlin@synology.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
rerror=ignore was returning true from scsi_handle_rw_error but the callers were not
calling scsi_req_complete when rerror=ignore returns true (this is the correct thing
to do when true is returned after executing a passthrough command). Fix this by
calling it in scsi_handle_rw_error.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a command fails with a sense that scsi_sense_buf_to_errno converts to
ECANCELED/EAGAIN/ENOTCONN or with a unit attention, scsi_req_complete is
called twice. This caused a crash.
Reported-by: Wangguang <wang.guangA@h3c.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When [2] was fixed it was agreed that adding and calling post_plug()
callback after device_reset() was low risk approach to hotfix issue
right before release. So it was merged instead of moving already
existing plug() callback after device_reset() is called which would
be more risky and require all plug() callbacks audit.
Looking at the current plug() callbacks, it doesn't seem that moving
plug() callback after device_reset() is breaking anything, so here
goes agreed upon [3] proper fix which essentially reverts [1][2]
and moves plug() callback after device_reset().
This way devices always comes to plug() stage, after it's been fully
initialized (including being reset), which fixes race condition [2]
without need for an extra post_plug() callback.
1. (25e897881 "qdev: add HotplugHandler->post_plug() callback")
2. (8449bcf94 "virtio-scsi: fix hotplug ->reset() vs event race")
3. https://www.mail-archive.com/qemu-devel@nongnu.org/msg549915.html
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1539696820-273275-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Pierre Morel<pmorel@linux.ibm.com>
Acked-by: Pierre Morel<pmorel@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Taking the address of a field in a packed struct is a bad idea, because
it might not be actually aligned enough for that pointer type (and
thus cause a crash on dereference on some host architectures). Newer
versions of clang warn about this. Avoid the bug by not using the
"modify in place" byte swapping functions.
This patch was produced with the following simple spatch script:
@@
expression E;
@@
-le16_to_cpus(&E);
+E = le16_to_cpu(E);
@@
expression E;
@@
-le32_to_cpus(&E);
+E = le32_to_cpu(E);
@@
expression E;
@@
-le64_to_cpus(&E);
+E = le64_to_cpu(E);
@@
expression E;
@@
-cpu_to_le16s(&E);
+E = cpu_to_le16(E);
@@
expression E;
@@
-cpu_to_le32s(&E);
+E = cpu_to_le32(E);
@@
expression E;
@@
-cpu_to_le64s(&E);
+E = cpu_to_le64(E);
followed by some minor tidying of overlong lines and bad indent.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180927134852.21490-1-peter.maydell@linaro.org>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180917053229.4853-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This option is added together with scsi-disk but is never honoured,
becuase we don't emulate the VPD page for scsi-block. We could intercept
and inject the user specified value like for max xfer len, but it's
probably not helpful since the intent of 070f80095a was for random
entropy aspects, not for performance. If emulated rotation rate is
desired, scsi-hd is more suitable.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180917083138.3948-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On some early machines the on-board PCI devices IRQs are wired directly to
the interrupt controller instead of via the PCI host bridge.
Add an optional external IRQ that if wired up via qdev will replace the
in-built PCI IRQ.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that these functions are no longer required they can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is the function that will soon be used to replace lsi53c895a_create() and
lsi53c810_create().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Allow toggling on/off the VIRTIO_SCSI_F_T10_PI feature bit for both
vhost-scsi and vhost-user-scsi devices.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-4-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the enablement of preset host features into the common
vhost_scsi_common_get_features() function. This is in preparation for
having vhost-scsi also make use of host_features.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-3-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In preparation for having vhost-scsi also make use of host_features,
move it from struct VHostUserSCSI into struct VHostSCSICommon.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-2-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The LSI 53c895a code does not handle the PPR Extended Message. Add
support to handle PPR Extended Message like SDTR and WDTR are handled.
That is, to skip past the message bytes and ignore the message.
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
mptsas1068 is currently listed as uncategorized device.
Mark it as storage device.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-Id: <1533076133-22745-1-git-send-email-linux@roeck-us.net>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reinstates commit b008326744,
which was temporarily reverted for the 3.0 release so that libvirt gets
some extra time to update their command lines.
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
There is a race condition during hotplug when iothread is used. It
occurs because virtio-scsi may be processing command queues in the
iothread while the monitor performs SCSI device hotplug.
When a SCSI device is hotplugged the HotplugHandler->plug() callback is
invoked and virtio-scsi emits a rescan event to the guest.
If the guest submits a SCSI command at this point then it may be
cancelled before hotplug completes. This happens because ->reset() is
called by hw/core/qdev.c:device_set_realized() after
HotplugHandler->plug() has been called and
hw/scsi/scsi-disk.c:scsi_disk_reset() purges all requests.
This patch uses the new HotplugHandler->post_plug() callback to emit the
rescan event after ->reset(). This eliminates the race conditions where
requests could be cancelled.
Reported-by: l00284672 <lizhengui@huawei.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20180716083732.3347-3-stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current BDC VPD page (page 0xb1) is too short. This can be
seen running sg_utils:
$ sg_vpd --page=bdc /dev/sda
Block device characteristics VPD page (SBC):
Block device characteristics VPD page length too short=8
By the SCSI spec, the expected size of the SBC page is 0x40.
There is no telling how the guest will behave with a shorter
message - it can ignore it, or worse, make (wrong)
assumptions.
This patch fixes the emulation by setting the size to 0x40.
This is the output of the previous sg_vpd command after
applying it:
$ sg_vpd --page=bdc /dev/sda -v
inquiry cdb: 12 01 b1 00 fc 00
Block device characteristics VPD page (SBC):
[PQual=0 Peripheral device type: disk]
Medium rotation rate is not reported
Product type: Not specified
WABEREQ=0
WACEREQ=0
Nominal form factor not reported
FUAB=0
VBULS=0
To improve readability, this patch also adds the VBULS value
explictly and add comments on the existing fields we're
setting.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This reverts commit b008326744.
Hold off removing this for one more QEMU release (current libvirt
release still uses it.)
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180625124238.25339-10-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The error handling policy was traditionally set with -drive, but with
-blockdev it is no longer possible to set frontend options. scsi-disk
(and other block devices) have long supported qdev properties to
configure the error handling policy, so let's add these options to
usb-storage as well and just forward them to the internal scsi-disk
instance.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The VPD Block Limits Inquiry page is optional, allowing SCSI devices
to not implement it. This is the case for devices like the MegaRAID
SAS 9361-8i and Microsemi PM8069.
In case of SCSI passthrough, the response of this request is used by
the QEMU SCSI layer to set the max_io_sectors that the guest
device will support, based on the value of the max_sectors_kb that
the device has set in the host at that time. Without this response,
the guest kernel is free to assume any value of max_io_sectors
for the SCSI device. If this value is greater than the value from
the host, SCSI Sense errors will occur because the guest will send
read/write requests that are larger than the underlying host device
is configured to support. An example of this behavior can be seen
in [1].
A workaround is to set the max_sectors_kb host value back in the guest
kernel (a process that can be automated using rc.local startup scripts
and the like), but this has several drawbacks:
- it can be troublesome if the guest has many passthrough devices that
needs this tuning;
- if a change in max_sectors_kb is made in the host side, manual change
in the guests will also be required;
- during an OS install it is difficult, and sometimes not possible, to
go to a terminal and change the max_sectors_kb prior to the installation.
This means that the disk can't be used during the install process. The
easiest alternative here is to roll back to scsi-hd, install the guest
and then go back to SCSI passthrough when the installation is done and
max_sectors_kb can be set.
An easier way would be to QEMU handle the absence of the Block Limits
VPD device response, setting max_io_sectors accordingly and allowing
the guest to use the device without the hassle.
This patch adds emulation of the Block Limits VPD response for
SCSI passthrough devices of type TYPE_DISK that doesn't support
it. The following changes were made:
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply. In case the device does not
- a new function called scsi_generic_set_vpd_bl_emulation,
that is called during device realize, was created to set a
new flag 'needs_vpd_bl_emulation' of the device. This function
retrieves the Inquiry EVPD response of the device to check for
VPD BL support.
- scsi_handle_inquiry_reply will now check the available VPD
pages from the Inquiry EVPD reply in case the device needs
VPD BL emulation, adding the Block Limits page (0xb0) to
the list. This will make the guest kernel aware of the
support that we're now providing by emulation.
- a new function scsi_emulate_block_limits creates the
emulated Block Limits response. This function is called
inside scsi_read_complete in case the device requires
Block Limits VPD emulation and we detected a SCSI Sense
error in the VPD Block Limits reply that was issued
from the guest kernel to the device. This error is
expected: we're reporting support from our side, but
the device isn't aware of it.
With this patch, the guest now queries the Block Limits
page during the device configuration because it is being
advertised in the Supported Pages response. It will either
receive the Block Limits page from the hardware, if it supports
it, or will receive an emulated response from QEMU. At any rate,
the guest now has the information to set the max_sectors_kb
parameter accordingly, sparing the user of SCSI sense errors
that would happen without the emulated response and in the
absence of Block Limits support from the hardware.
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1566195
Reported-by: Dac Nguyen <dacng@us.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-4-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For the VPD Block Limits emulation with SCSI passthrough,
we'll issue an Inquiry request with EVPD set to retrieve
the available VPD pages of the device. This would be done in
a way similar of what scsi_generic_read_device_identification
does: create a SCSI command and a reply buffer, fill in the
sg_io_hdr_t structure, call blk_ioctl, check if an error
occurred, process the response.
This same process is done in other 2 functions, get_device_type
and get_stream_blocksize. They differ in the command/reply
buffer and post-processing, everything else is almost a
copy/paste.
Instead of adding a forth copy/pasted-ish code when adding
the passthrough VPD BL emulation, this patch extirpates
this repetition of those 3 functions and put it into
a new one called scsi_SG_IO_FROM_DEV. Any future code that
wants to execute an SG_DXFER_FROM_DEV to the device can
use it, avoiding filling sg_io_hdr_t again and et cetera.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-3-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To add support for the emulation of Block Limits VPD page
for passthrough devices, a few adjustments in the current code
base is required to avoid repetition and improve clarity.
In scsi-generic.c, detach the Inquiry handling from
scsi_read_complete and put it into a new function called
scsi_handle_inquiry_reply. This change aims to avoid
cluttering of scsi_read_complete when we more logic in the
Inquiry response handling is added in the next patches,
centralizing the changes in the new function.
In scsi-disk.c, take the build of all emulated VPD pages
from scsi_disk_emulate_inquiry and make it available to
other files into a non-static function called
scsi_disk_emulate_vpd_page. Making it public will allow
the future VPD BL emulation code for passthrough devices
to use it from scsi-generic.c, avoiding copy/pasting this
code solely for that purpose. It also has the advantage of
providing emulation of all VPD pages in case we need to
emulate other pages in other scenarios. As a bonus,
scsi_disk_emulate_inquiry got tidier.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20180627172432.11120-2-danielhb413@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the legacy esp_init() function now that there are no more remaining
users.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180613094727.11326-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
The preferred way to select the KVM accelerator is to use "-accel kvm"
these days, so let's be consistent in our documentation and help texts.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1528866321-23886-3-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No reason for vhost-scsi to pull in migration headers directly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is only half of the work, because the proxy devices (virtio-*-pci,
virtio-*-ccw, etc.) are still included unconditionally. It is still a
move in the right direction.
Based-on: <20180522194943.24871-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove those unneeded includes to speed up the compilation
process a little bit.
Code change produced with:
$ git grep '#include "sysemu/blockdev.h"' | \
cut -d: -f-1 | \
xargs egrep -L "(BlockInterfaceType|DriveInfo|drive_get|blk_legacy_dinfo|blockdev_mark_auto_del)" | \
xargs sed -i.bak '/#include "sysemu\/blockdev.h"/d'
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-15-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove those unneeded includes to speed up the compilation
process a little bit. (Continue 7eceff5b5a cleanup)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-13-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As part of plumbing MemTxAttrs down to the IOMMU translate method,
add MemTxAttrs as an argument to the MemoryRegion valid.accepts
callback. We'll need this for subpage_accepts().
We could take the approach we used with the read and write
callbacks and add new a new _with_attrs version, but since there
are so few implementations of the accepts hook we just change
them all.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180521140402.23318-9-peter.maydell@linaro.org
When multi queue is enabled e.g. for a virtio-net device,
each queue pair will have a vhost_dev, and the only thing
shared between vhost devs currently is the chardev. This
patch introduces a vhost-user state structure which will
be shared by all vhost devs of the same virtio device.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU SCSI code makes assumptions about how the PROTECT and BYTCHK
works in the protocol, denying support for PI (Protection
Information) in case the guest OS requests it. However, in SCSI versions 2
and older, there is no PI concept in the protocol.
This means that when dealing with such devices:
- there is no PROTECT bit in byte 5 of the standard INQUIRY response. The
whole byte is marked as "Reserved";
- there is no RDPROTECT in byte 2 of READ. We have 'Logical Unit Number'
in this field instead;
- there is no VRPROTECT in byte 2 of VERIFY. We have 'Logical Unit Number'
in this field instead. This also means that the BYTCHK bit in this case
is not related to PI.
Since QEMU does not consider these changes, a SCSI passthrough using
a SCSI-2 device will not work. It will mistake these fields with
PI information and return Illegal Request SCSI SENSE thinking
that the driver is asking for PI support.
This patch fixes it by adding a new attribute called 'scsi_version'
that is read from the standard INQUIRY response of passthrough
devices. This allows for a version verification before applying
conditions related to PI that doesn't apply for older versions.
Reported-by: Dac Nguyen <dacng@us.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Message-Id: <20180327211451.14647-1-danielhb@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We would like to have different behavior for passthrough devices
depending on the SCSI version they expose. To prepare for that,
allow the user of emulated devices to specify the desired SCSI
level, and adjust the emulation according to the property value.
The next patch will set the level for scsi-block and scsi-generic
devices.
Based on a patch by Daniel Henrique Barboza
<danielhb@linux.vnet.ibm.com>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some backends report big max_io_sectors. Making min_io_size the same
value in this case will make it impossible for guest to align memory,
therefore the disk may not be usable at all.
Do not enlarge them when they are zero.
Reported-by: David Gibson <dgibson@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180327164141.19075-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the user does not have permissions to send ioctls to the device (due to
SELinux or cgroups, for example), the output can look like
qemu-kvm: -device scsi-block,drive=disk: cannot get SG_IO version number:
Operation not permitted. Is this a SCSI device?
but this is confusing because the ioctl was blocked _before_ the device
even received the SG_GET_VERSION_NUM ioctl. Therefore, for EPERM errors
the suggestion should be eliminated. To make that simpler, change the
code to use error_append_hint.
Reported-by: Ala Hino <ahino@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The global hack for creating SCSI devices has recently been removed,
but this apparently broke SCSI devices on some boards that were not
ready for this change yet. For the 40p machine you now get:
$ ppc64-softmmu/qemu-system-ppc64 -M 40p -cdrom x.iso
qemu-system-ppc64: -cdrom x.iso: machine type does not support if=scsi,bus=0,unit=2
Fix it by providing a lsi53c810_create() function that takes care
of calling scsi_bus_legacy_handle_cmdline() after creating the
corresponding SCSI controller.
Fixes: 1454509726
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The global hack for creating SCSI devices has recently been removed,
but this apparently broke SCSI devices on some boards that were not
ready for this change yet. For the pica61 machine you now get:
$ mips64-softmmu/qemu-system-mips64 -M pica61 -cdrom x.iso
qemu-system-mips64: -cdrom x.iso: machine type does not support if=scsi,bus=0,unit=2
Fix it by calling scsi_bus_legacy_handle_cmdline() after creating the
corresponding SCSI controller.
Fixes: 1454509726
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1520414644-11535-1-git-send-email-thuth@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A NDOB bit set to one specifies that the disk shall not transfer data
from the data-out buffer and shall process the command as if the data-out
buffer contained user data set to all zeroes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After reviewing a patch from Philippe that removes block-backend.h
from hw/lm32/milkymist.c, I noticed that this header is included
unnecessarily in a lot of other files, too. Remove those unneeded
includes to speed up the compilation process a little bit.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1518684912-31637-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The calculation of the max_transfer atribute of BlockDriverState
makes considerations such as max_segments and transfer_length via
the BLKSECTGET ioctl (if available).
However, bl->max_transfer isn't considered when emulating the INQUIRY
'Block Limit' response to the scsi-hd devices. This leads to situations
where the declared max_sectors from the INQUIRY response is inconsistent
with the block limits, which isn't ideal. It can also be misleading to the
user that sets /sys/block/<dev>/queue/max_sectors_kb to a certain
value, then finds a different value in the guest OS for the same disk.
Following the same logic scsi_read_complete from scsi-generic.c does
when patching the response of the Block Limits VPD back to the guest,
change the max_io_sectors value of the emulated Block Limits VPD
response by considering the blk_get_max_transfer of the related
BlockDriverState. Use MIN_NOT_ZERO to be sure that the minimal
value is chosen.
Given that we're changing max_io_sectors, consider that min_io_sectors
and opt_io_sectors can't be greater than the new calculated value.
Signed-off-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180306154411.18462-1-danielhb@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If the main loop thread invokes .ioeventfd_stop() just as the vq handler
function begins in the IOThread then the handler may lose the race for
the AioContext lock. By the time the vq handler is able to acquire the
AioContext lock the ioeventfd has already been removed and the handler
isn't supposed to run anymore!
Use the new aio_wait_bh_oneshot() function to perform ioeventfd removal
from within the IOThread. This way no races with the vq handler are
possible.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20180307144205.20619-4-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Automatic creation of SCSI controllers for "-drive if=scsi" for x86
machines was quite a bad idea (see description of commit f778a82f0c
for details). This is marked as deprecated since QEMU v2.9.0, and as
far as I know, nobody complained that this is still urgently required
anymore. Time to remove this now.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1519123357-13225-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJagxKDAAoJECgfDbjSjVRp5qAH/3gmgBaIzL3KRHd5i0RZifJv
PvyAVYgZd7h0+/1r9GM7guHKyEPZ08JtbHSm/HuDV4BD/Vf3/8joy8roExIfde2A
6k8fd6ANVQmE3t5zUxNXi9qiG4pO4xDIu4cMAbixzgN9x5ttlcfTw7fTT0e0VJxJ
8SN02/uCPPR/DY4/cpjah+slSyv6rBKT1v1ONy7djyRTYHi6h3Meoh05YfEALkwA
goxTKBZHi0L1IZ3HP/ZpXJDohQ5n2P09DX0fQgb8PgmW6WIWB/Qpi5pD53LZpMCV
n9waTF0U0ahneFd2FHo22QMMrwWvQyrjv+w5uXVr+qmHb/OyH2tUt7PgGF9+QKA=
=78s5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,vhost,pci,pc: features, fixes and cleanups
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 13 Feb 2018 16:29:55 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
virtio-balloon: include statistics of disk/file caches
acpi-test: update FADT
lpc: drop pcie host dependency
tests: acpi: fix FADT not being compared to reference table
hw/pci-bridge: fix pcie root port's IO hints capability
libvhost-user: Support across-memory-boundary access
libvhost-user: Fix resource leak
virtio-balloon: unref the memory region before continuing
pci: removed the is_express field since a uniform interface was inserted
virtio-blk: enable multiple vectors when using multiple I/O queues
pci/bus: let it has higher migration priority
pci-bridge/i82801b11: clear bridge registers on platform reset
vhost: Move log_dirty check
vhost: Merge and delete unused callbacks
vhost: Clean out old vhost_set_memory and friends
vhost: Regenerate region list from changed sections list
vhost: Merge sections added to temporary list
vhost: Simplify ring verification checks
vhost: Build temporary section list and deref after commit
virtio: improve virtio devices initialization time
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu-common.h includes qemu/option.h, but most places that include the
former don't actually need the latter. Drop the include, and add it
to the places that actually need it.
While there, drop superfluous includes of both headers, and
separate #include from file comment with a blank line.
This cleanup makes the number of objects depending on qemu/option.h
drop from 4545 (out of 4743) to 284 in my "build everything" tree.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-20-armbru@redhat.com>
[Semantic conflict with commit bdd6a90a9e in block/nvme.c resolved]
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
according to Eduardo Habkost's commit fd3b02c889 all PCIEs now implement
INTERFACE_PCIE_DEVICE so we don't need is_express field anymore.
Devices that implements only INTERFACE_PCIE_DEVICE (is_express == 1)
or
devices that implements only INTERFACE_CONVENTIONAL_PCI_DEVICE (is_express == 0)
where not affected by the change.
The only devices that were affected are those that are hybrid and also
had (is_express == 1) - therefor only:
- hw/vfio/pci.c
- hw/usb/hcd-xhci.c
- hw/xen/xen_pt.c
For those 3 I made sure that QEMU_PCI_CAP_EXPRESS is on in instance_init()
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Yoni Bettan <ybettan@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtio_bus_set_host_notifier function no longer calls
event_notifier_cleanup when a event notifier is removed.
The commit updates the code to match the new behavior and calls
virtio_bus_cleanup_host_notifier after the notifier was de-assign
and no longer in use.
This change is a preparation to allow executing the
virtio_bus_set_host_notifier function in a memory region
transaction.
Signed-off-by: Gal Hammer <ghammer@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Coverity doesn't like the ignored return value introduced in
9d3b155186 (hw/block: Fix the return type), and other callers are
converted already in ceff3e1f01.
This one was added lately in d9bcd6f7f2 and missed the train. Do it
now.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20180118025245.13042-1-famz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because usb-storage creates an internal scsi device, we should propagate
options. We already do so for bootindex etc, but failed to take care of
share-rw. Fix it in an apparent way: add a new parameter to
scsi_bus_legacy_add_drive and pass in s->conf.share_rw.
Cc: qemu-stable@nongnu.org
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-id: 20180117005222.4781-1-famz@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
scsi_write_same_complete() can retry the write if the request was
unaligned. Make sure to release the AioContext when that code path is
taken!
This patch fixes a hang when QEMU terminates after an unaligned WRITE
SAME request has been processed with dataplane. The hang occurs because
iothread_stop_all() cannot acquire the AioContext lock that was leaked
by the IOThread in scsi_write_same_complete().
Fixes: b9e413dd37 ("block: explicitly acquire aiocontext in aio callbacks that need it").
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-stable@nongnu.org
Reported-by: Cong Li <coli@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20180104142502.15175-1-stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the property to the device model, then parse it by calling
blkconf_apply_backend_options().
In addition to blk_set_perm(), the called function also handles error
options and wce. For error options we've already checked that the
default values are used, for wce we don't have the option either so it
is always the default (true). In other words there is no change of
behavior in these regards.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20171205151553.7834-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Extract the common parts of scsi_sense_buf_to_errno, scsi_convert_sense
and scsi_target_send_command's REQUEST SENSE handling into two new
functions scsi_parse_sense_buf and scsi_build_sense_buf.
Fix a bug in scsi_target_send_command along the way; the length was
written in buf[10] rather than buf[7].
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixes: b07fbce634 ("scsi-bus: correct responses for INQUIRY and REQUEST SENSE")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Scsi-block doesn't use the DEFINE_BLOCK_PROPERTIES() macro so it didn't
gain the share-rw back when it was added to all other storage devices.
This option is meaningful here, and need to be used when attaching a
shared storage to guest.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20171205071928.30242-1-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[Drop virtio_blk_data_plane_create() change that misinterprets return
value when the virtio transport does not support dataplane.
--Stefan]
Cc: John Snow <jsnow@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: e77848d3735ba590f23ffbf8094379c646c33d79.1511317952.git.maozy.fnst@cn.fujitsu.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
applied using ./scripts/clean-includes
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Ben Warren <ben@skyportsystems.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The bus pointer in PCIDevice is basically redundant with QOM information.
It's always initialized to the qdev_get_parent_bus(), the only difference
is the type.
Therefore this patch eliminates the field, instead creating a pci_get_bus()
helper to do the type mangling to derive it conveniently from the QOM
Device object underneath.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
A fair proportion of the users of pci_bus_num() want to get the bus
number on a specific device, so first have to look up the bus from the
device then call it. This adds a helper to do that (since we're going
to make looking up the bus slightly more verbose).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Commit 5c0919d020 ("virtio-scsi: Add virtqueue_size parameter allowing
virtqueue size to be set.") introduced a new parameter to virtio-scsi.
Later, commit 9200361060 ("vhost-user-scsi: add missing virtqueue_size
param") added that parameter to the new vhost-user-scsi interface but
neglected the existing vhost-scsi interface it was built on.
Apply the same change to vhost-scsi, so that we can boot a guest with
a device defined. This also avoids crashing a guest when hotplugging
a vhost-scsi device.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-id: 20171201151538.6844-2-farman@linux.vnet.ibm.com
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 5c0919d0 [1] introduced virtqueue_size parameter
for common virtio-scsi path, without updaing the vhost-user-scsi
code. vhost-user-scsi devices right now report size 0 for each vq.
This patch introduces virtqueue_size param to vhost-user-scsi,
that can now be set by the user. However, the most importantly, it
now has a default value of 128 (same as QEMU's virtio-scsi).
[1] 5c0919d0 ("virtio-scsi: Add virtqueue_size parameter
allowing virtqueue size to be set.")
Change-Id: I70e87eab702ebf1196c028dbf17d54fdc0c89a14
Signed-off-by: Dariusz Stojaczyk <dariuszx.stojaczyk@intel.com>
Message-Id: <1510676916-76409-1-git-send-email-dariuszx.stojaczyk@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This enables them to be used outside of esp.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Logical block size of a SCSI disk should never be larger than
physical block size. From an ATA/SCSI perspective, it makes no sense
to have the logical block size greater than the physical block size,
and it cannot even be effectively expressed in the command set. The
whole point of adding the physical block size to the ATA/SCSI command
set was to communicate a desire for a larger block size (than logical),
while maintaining backwards compatibility with legacy 512 byte block
size.
When setting logical_block_size > physical_block_size, QEMU cannot express
it in READ CAPACITY(16) output, and all it can do is set the physical
block exponent to 0 (i.e. logical_block_size == physical_block_size).
Reporting the error properly, however, is better.
Signed-off-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Message-Id: <1508185024-5840-1-git-send-email-mark.kanda@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add INTERFACE_CONVENTIONAL_PCI_DEVICE to all direct subtypes of
TYPE_PCI_DEVICE, except:
1) The ones that already have INTERFACE_PCIE_DEVICE set:
* base-xhci
* e1000e
* nvme
* pvscsi
* vfio-pci
* virtio-pci
* vmxnet3
2) base-pci-bridge
Not all PCI bridges are Conventional PCI devices, so
INTERFACE_CONVENTIONAL_PCI_DEVICE is added only to the subtypes
that are actually Conventional PCI:
* dec-21154-p2p-bridge
* i82801b11-bridge
* pbm-bridge
* pci-bridge
The direct subtypes of base-pci-bridge not touched by this patch
are:
* xilinx-pcie-root: Already marked as PCIe-only.
* pcie-pci-bridge: Already marked as PCIe-only.
* pcie-port: all non-abstract subtypes of pcie-port are already
marked as PCIe-only devices.
3) megasas-base
Not all megasas devices are Conventional PCI devices, so the
interface names are added to the subclasses registered by
megasas_register_types(), according to information in the
megasas_devices[] array.
"megasas-gen2" already implements INTERFACE_PCIE_DEVICE, so add
INTERFACE_CONVENTIONAL_PCI_DEVICE only to "megasas".
Acked-by: Alberto Garcia <berto@igalia.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Change all devices that set is_express=1 to implement
INTERFACE_PCIE_DEVICE.
Cc: Keith Busch <keith.busch@intel.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Dmitry Fleytman <dmitry@daynix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: qemu-block@nongnu.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The following devices support both PCI Express and Conventional
PCI, by including special code to handle the QEMU_PCI_CAP_EXPRESS
flag and/or conditional pcie_endpoint_cap_init() calls:
* vfio-pci (is_express=1, but legacy PCI handled by
vfio_populate_device())
* vmxnet3 (is_express=0, but PCIe handled by vmxnet3_realize())
* pvscsi (is_express=0, but PCIe handled by pvscsi_realize())
* virtio-pci (is_express=0, but PCIe handled by
virtio_pci_dc_realize(), and additional legacy PCI code at
virtio_pci_realize())
* base-xhci (is_express=1, but pcie_endpoint_cap_init() call
is conditional on pci_bus_is_express(dev->bus)
* Note that xhci does not clear QEMU_PCI_CAP_EXPRESS like the
other hybrid devices
Cc: Dmitry Fleytman <dmitry@daynix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Linux kernel will query the SCSI "Block device characteristics"
VPD to determine the rotations per minute of the disk. If this has
the value 1, it is taken to be an SSD and so Linux sets the
'rotational' flag to 0 for the I/O queue and will stop using that
disk as a source of random entropy. Other operating systems may
also take into account rotation rate when setting up default
behaviour.
Mgmt apps should be able to set the rotation rate for virtualized
block devices, based on characteristics of the host storage in use,
so that the guest OS gets sensible behaviour out of the box. This
patch thus adds a 'rotation-rate' parameter for 'scsi-hd' and
'scsi-block' device types. For the latter, this parameter will be
ignored unless the host device has TYPE_DISK.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <20171004114008.14849-2-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
SunOS defines ESP (x86 register) in <sys/regset.h> as 7.
This fixes build on SmartOS (Joyent).
Signed-off-by: Kamil Rytarowski <n54@gmx.com>
Message-Id: <20170909142116.26816-1-n54@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Complete the transition by renaming this header, which was
shared by block/iscsi.c and the SCSI emulation code.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move more knowledge of SG_IO out of hw/scsi/scsi-generic.c, for
reusability.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move more knowledge of sense data format out of hw/scsi/scsi-bus.c
for reusability.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
util/scsi.c includes some SCSI code that is shared by block/iscsi.c and
hw/scsi, but the introduction of the persistent reservation helper
will add many more instances of this. There is also include/block/scsi.h,
which actually is not part of the core block layer.
The persistent reservation manager will also need a home. A scsi/
directory provides one for both the aforementioned shared code and
the PR manager code.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After introducing the scsi/ subdirectory, there will be a scsi_build_sense
function that is the same as scsi_req_build_sense but without needing
a SCSIRequest. The existing scsi_build_sense function gets in the way,
remove it.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes the werror/rerror options available on the scsi-block device,
to allow user specify error handling policy similar to scsi-hd.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170821141008.19383-5-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to SPC-3 INQUIRY and REQUEST SENSE should return GOOD
even on unsupported LUNS.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Message-Id: <1503049022-14749-1-git-send-email-hare@suse.de>
Reported-by: Laszlo Ersek <lersek@redhat.com>
Fixes: ded6ddc5a7
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Since Linux switched to blk-mq as the default in Linux commit
5c279bd9e406 ("scsi: default to scsi-mq"), virtio-scsi LUNs consume
about 10x as much guest kernel memory.
This commit allows you to choose the virtqueue size for each
virtio-scsi-pci controller like this:
-device virtio-scsi-pci,id=scsi,virtqueue_size=16
The default is still 128 as before. Using smaller virtqueue_size
allows many more disks to be added to small memory virtual machines.
For a 1 vCPU, 500 MB, no swap VM I observed:
With scsi-mq enabled (upstream kernel): 175 disks
-"- ditto -"- virtqueue_size=64: 318 disks
-"- ditto -"- virtqueue_size=16: 775 disks
With scsi-mq disabled (kernel before 5c279bd9e406): 1755 disks
Note that to have any effect, this requires a kernel patch:
https://lkml.org/lkml/2017/8/10/689
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Message-Id: <20170810165255.20865-1-rjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The LUN0 emulation is just that, an emulation for a non-existing
LUN0. So we should be returning LUN_NOT_SUPPORTED for any request
coming from any other LUN.
And we should be aborting unhandled commands with INVALID OPCODE,
not LUN NOT SUPPORTED.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Message-Id: <1501835795-92331-4-git-send-email-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert a device model where initialization obviously
can't fail, make it implement realize() rather than init().
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Message-Id: <20170726084153.10121-2-maozy.fnst@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_bh_new() is a wrapper around aio_bh_new(), which returns
null only when g_new() does. It doesn't. So remove the dead
error handling.
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Message-Id: <20170726084153.10121-1-maozy.fnst@cn.fujitsu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In trace format '#' flag of printf is forbidden. Fix it to '0x%'.
This patch is created by the following:
check that we have a problem
> find . -name trace-events | xargs grep '%#' | wc -l
56
check that there are no cases with additional printf flags before '#'
> find . -name trace-events | xargs grep "%[-+ 0'I]+#" | wc -l
0
check that there are no wrong usage of '#' and '0x' together
> find . -name trace-events | xargs grep '0x%#' | wc -l
0
fix the problem
> find . -name trace-events | xargs sed -i 's/%#/0x%/g'
[Eric Blake noted that xargs grep '%[-+ 0'I]+#' should be xargs grep
"%[-+ 0'I]+#" instead so the shell quoting is correct.
--Stefan]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170731160135.12101-3-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
On NetBSD, where tolower() and toupper() are implemented using an
array lookup, the compiler warns if you pass a plain 'char'
to these functions:
gdbstub.c:914:13: warning: array subscript has type 'char'
This reflects the fact that toupper() and tolower() give
undefined behaviour if they are passed a value that isn't
a valid 'unsigned char' or EOF.
We have qemu_tolower() and qemu_toupper() to avoid this problem;
use them.
(The use in scsi-generic.c does not trigger the warning because
it passes a uint8_t; we switch it anyway, for consistency.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> for the s390 part.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 1500568290-7966-1-git-send-email-peter.maydell@linaro.org
If no drive=... option is passed (for an empty drive), we don't only
lack the BlockBackend normally created by parse_drive(), but we also
need to manually call blk_attach_dev().
This fixes at least a segfault when unplugging such devices, the bug
that they didn't show up in query-block, and probably some more
problems.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Paolo Bonzini