During boot, PAPR guests negotiate CPU model support with the
ibm,client-architecture-support mechanism. The logic to implement this in
qemu is very convoluted. This cleans it up to be cleaner, using the new
ppc_check_compat() call.
The new logic for choosing a compatibility mode is:
1. Usually, use the most recent compatibility mode that is
a) supported by the guest
b) supported by the CPU
and c) no later than the maximum allowed (if specified)
2. If no suitable compatibility mode was found, the guest *does*
support this CPU explicitly, and no maximum compatibility mode is
specified, then use "raw" mode for the current CPU
3. Otherwise, fail the boot.
This differs from the results of the old code: the old code preferred using
"raw" mode to a compatibility mode, whereas the new code prefers a
compatibility mode if available. Using compatibility mode preferentially
means that we're more likely to be able to migrate the guest to a similar
but not identical host.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Added CONFIG_RS6000_MC to ppc64 or it breaks testcases]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This device is a partial duplicate of System I/O device available in hw/ppc/prep.c
This new one doesn't have all the Motorola-specific registers.
The old one should be deprecated and removed with the 'prep' machine.
Partial documentation available at
ftp://ftp.software.ibm.com/rs6000/technology/spec/srp1_1.exe
section 6.1.5 (I/O Device Mapping)
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This adds support for Dynamic DMA Windows (DDW) option defined by
the SPAPR specification which allows to have additional DMA window(s)
The "ddw" property is enabled by default on a PHB but for compatibility
the pseries-2.6 machine and older disable it.
This also creates a single DMA window for the older machines to
maintain backward migration.
This implements DDW for PHB with emulated and VFIO devices. The host
kernel support is required. The advertised IOMMU page sizes are 4K and
64K; 16M pages are supported but not advertised by default, in order to
enable them, the user has to specify "pgsz" property for PHB and
enable huge pages for RAM.
The existing linux guests try creating one additional huge DMA window
with 64K or 16MB pages and map the entire guest RAM to. If succeeded,
the guest switches to dma_direct_ops and never calls TCE hypercalls
(H_PUT_TCE,...) again. This enables VFIO devices to use the entire RAM
and not waste time on map/unmap later. This adds a "dma64_win_addr"
property which is a bus address for the 64bit window and by default
set to 0x800.0000.0000.0000 as this is what the modern POWER8 hardware
uses and this allows having emulated and VFIO devices on the same bus.
This adds 4 RTAS handlers:
* ibm,query-pe-dma-window
* ibm,create-pe-dma-window
* ibm,remove-pe-dma-window
* ibm,reset-pe-dma-window
These are registered from type_init() callback.
These RTAS handlers are implemented in a separate file to avoid polluting
spapr_iommu.c with PCI.
This changes sPAPRPHBState::dma_liobn to an array to allow 2 LIOBNs
and updates all references to dma_liobn. However this does not add
64bit LIOBN to the migration stream as in fact even 32bit LIOBN is
rather pointless there (as it is a PHB property and the management
software can/should pass LIOBNs via CLI) but we keep it for the backward
migration support.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Move all trace-events for files in the hw/ppc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 1466066426-16657-27-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Laurent Vivier