After a flash device enters CFI mode from autoselect mode, the reset
command returns the device to autoselect mode. An additional reset
command is necessary to return to read array mode.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-7-stephen.checkoway@oberlin.edu>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Some flash chips support sectors of different sizes. For example, the
AMD AM29LV160DT has 31 64 kB sectors, one 32 kB sector, two 8 kB
sectors, and a 16 kB sector, in that order. The AM29LV160DB has those in
the reverse order.
The `num-blocks` and `sector-length` properties work exactly as they did
before: a flash device with uniform sector lengths. To get non-uniform
sector lengths for up to four regions, the following properties may be
set
- region 0. `num-blocks0` and `sector-length0`;
- region 1. `num-blocks1` and `sector-length1`;
- region 2. `num-blocks2` and `sector-length2`; and
- region 3. `num-blocks3` and `sector-length3`.
If the uniform and nonuniform properties are set, then both must specify
a flash device with the same total size. It would be better to disallow
both being set, or make `num-blocks0` and `sector-length0` alias
`num-blocks` and `sector-length`, but that would make testing currently
impossible.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Rebased, add assert() on pri_offset]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Introduce the FlashConfig structure, to be able to run the same set
of tests on different flash models/configurations.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Most AMD commands only examine 11 bits of the address. This masks the
addresses used in the comparison to 11 bits. The exceptions are word or
sector addresses which use offset directly rather than the shifted
offset, boff.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-4-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Test the AMD command set for parallel flash chips. This test uses an
ARM musicpal board with a pflash drive to test the following list of
currently-supported commands.
- Autoselect
- CFI
- Sector erase
- Chip erase
- Program
- Unlock bypass
- Reset
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-2-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: reworded the patch subject, g_assert_cmpint -> cmphex]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Stephen Checkoway