This patch aims to bring the following behavior:
1. We don't load bitmaps, when started in inactive mode. It's the case
of incoming migration. In this case we wait for bitmaps migration
through migration channel (if 'dirty-bitmaps' capability is enabled) or
for invalidation (to load bitmaps from the image).
2. We don't remove persistent bitmaps on inactivation. Instead, we only
remove bitmaps after storing. This is the only way to restore bitmaps,
if we decided to resume source after [failed] migration with
'dirty-bitmaps' capability enabled (which means, that bitmaps were not
stored).
3. We load bitmaps on open and any invalidation, it's ok for all cases:
- normal open
- migration target invalidation with dirty-bitmaps capability
(bitmaps are migrating through migration channel, the are not
stored, so they should have IN_USE flag set and will be skipped
when loading. However, it would fail if bitmaps are read-only[1])
- migration target invalidation without dirty-bitmaps capability
(normal load of the bitmaps, if migrated with shared storage)
- source invalidation with dirty-bitmaps capability
(skip because IN_USE)
- source invalidation without dirty-bitmaps capability
(bitmaps were dropped, reload them)
[1]: to accurately handle this, migration of read-only bitmaps is
explicitly forbidden in this patch.
New mechanism for not storing bitmaps when migrate with dirty-bitmaps
capability is introduced: migration filed in BdrvDirtyBitmap.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Similarly to merge, it's OK to allow clear operations on disabled
bitmaps, as this condition only means that they are not recording
new writes. We are free to clear it if the user requests it.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20181002230218.13949-4-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
In prior commits that made merge transactionable, we removed the
assertion that merge cannot operate on disabled bitmaps. In addition,
we want to make sure that we are prohibiting merges to "locked" bitmaps.
Use the new user_locked function to check.
Reported-by: Eric Blake <eblake@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20181002230218.13949-3-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Instead of both frozen and qmp_locked checks, wrap it into one check.
frozen implies the bitmap is split in two (for backup), and shouldn't
be modified. qmp_locked implies it's being used by another operation,
like being exported over NBD. In both cases it means we shouldn't allow
the user to modify it in any meaningful way.
Replace any usages where we check both frozen and qmp_locked with the
new check.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181002230218.13949-2-jsnow@redhat.com
[w/edits Suggested-By: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>]
Signed-off-by: John Snow <jsnow@redhat.com>
This variable doesn't work as it should, because it is actually cleared
in qcow2_co_invalidate_cache() by memset(). Drop it, as the following
patch will introduce new behavior.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[Maintainer edit -- touched up error message. --js]
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Add backup parameter to bdrv_merge_dirty_bitmap() to be used then with
bdrv_restore_dirty_bitmap() if it needed to restore the bitmap after
merge operation.
This is needed to implement bitmap merge transaction action in further
commit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Use more generic names to reuse the function for bitmap merge in the
following commit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Move checks from qmp_x_block_dirty_bitmap_merge() to
bdrv_merge_dirty_bitmap(), to share them with dirty bitmap merge
transaction action in future commit.
Note: for now, only qmp_x_block_dirty_bitmap_merge() calls
bdrv_merge_dirty_bitmap().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
vpc_open() merely prints a warning when it finds a bad header
checksum. Turn that into a hard error.
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20181017082702.5581-39-armbru@redhat.com>
[Error message capitalized for local consistency]
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Calling error_report() in a function that takes an Error ** argument
is suspicious. Convert a few that are actually warnings to
warn_report().
While there, split warnings consisting of multiple sentences to
conform to conventions spelled out in warn_report()'s contract, and
improve a rather useless warning in sheepdog.c.
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Lieven <pl@kamp.de>
Cc: Liu Yuan <namei.unix@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181017082702.5581-4-armbru@redhat.com>
Drop changes to "without an explicit read-only=on" warnings, because
there's a series removing them pending. Also drop a cc: to a former
Sheepdog maintainer.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
From include/qapi/error.h:
* Pass an existing error to the caller with the message modified:
* error_propagate(errp, err);
* error_prepend(errp, "Could not frobnicate '%s': ", name);
Fei Li pointed out that doing error_propagate() first doesn't work
well when @errp is &error_fatal or &error_abort: the error_prepend()
is never reached.
Since I doubt fixing the documentation will stop people from getting
it wrong, introduce error_propagate_prepend(), in the hope that it
lures people away from using its constituents in the wrong order.
Update the instructions in error.h accordingly.
Convert existing error_prepend() next to error_propagate to
error_propagate_prepend(). If any of these get reached with
&error_fatal or &error_abort, the error messages improve. I didn't
check whether that's the case anywhere.
Cc: Fei Li <fli@suse.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181017082702.5581-2-armbru@redhat.com>
nvme_poll_queues is already protected by q->lock, and
AIO callbacks are invoked outside the AioContext lock.
So remove the acquire/release pair in nvme_handle_event.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20180814062739.19640-1-pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Currently, the default values for werror and rerror have to be set
explicitly with blk_set_on_error() by the callers of blk_new(). The only
caller actually doing this is blockdev_init(), which is called for
BlockBackends created using -drive.
In particular, anonymous BlockBackends created with
-device ...,drive=<node-name> didn't get the correct default set and
instead defaulted to the integer value 0 (= BLOCKDEV_ON_ERROR_REPORT).
This is the intended default for rerror anyway, but the default for
werror should be BLOCKDEV_ON_ERROR_ENOSPC.
Set the defaults in blk_new() instead so that they apply no matter what
way the BlockBackend was created.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Leonid Bloch <lbloch@janustech.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The default cache-clean-interval is set to 10 minutes, in order to lower
the overhead of the qcow2 caches (before the default was 0, i.e.
disabled).
* For non-Linux platforms the default is kept at 0, because
cache-clean-interval is not supported there yet.
Signed-off-by: Leonid Bloch <lbloch@janustech.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The caches are now recalculated upon image resizing. This is done
because the new default behavior of assigning L2 cache relatively to
the image size, implies that the cache will be adapted accordingly
after an image resize.
Signed-off-by: Leonid Bloch <lbloch@janustech.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The upper limit on the L2 cache size is increased from 1 MB to 32 MB
on Linux platforms, and to 8 MB on other platforms (this difference is
caused by the ability to set intervals for cache cleaning on Linux
platforms only).
This is done in order to allow default full coverage with the L2 cache
for images of up to 256 GB in size (was 8 GB). Note, that only the
needed amount to cover the full image is allocated. The value which is
changed here is just the upper limit on the L2 cache size, beyond which
it will not grow, even if the size of the image will require it to.
Signed-off-by: Leonid Bloch <lbloch@janustech.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sufficient L2 cache can noticeably improve the performance when using
large images with frequent I/O.
Previously, unless 'cache-size' was specified and was large enough, the
L2 cache was set to a certain size without taking the virtual image size
into account.
Now, the L2 cache assignment is aware of the virtual size of the image,
and will cover the entire image, unless the cache size needed for that is
larger than a certain maximum. This maximum is set to 1 MB by default
(enough to cover an 8 GB image with the default cluster size) but can
be increased or decreased using the 'l2-cache-size' option. This option
was previously documented as the *maximum* L2 cache size, and this patch
makes it behave as such, instead of as a constant size. Also, the
existing option 'cache-size' can limit the sum of both L2 and refcount
caches, as previously.
Signed-off-by: Leonid Bloch <lbloch@janustech.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The refcount cache size does not need to be set to its minimum value in
read_cache_sizes(), as it is set to at least its minimum value in
qcow2_update_options_prepare().
Signed-off-by: Leonid Bloch <lbloch@janustech.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Leonid Bloch <lbloch@janustech.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The file-posix code is used for the "file", "host_device" and
"host_cdrom" drivers, and it allows reopening images. However the only
option that is actually processed is "x-check-cache-dropped", and
changes in all other options (e.g. "filename") are silently ignored:
(qemu) qemu-io virtio0 "reopen -o file.filename=no-such-file"
While we could allow changing some of the other options, let's keep
things as they are for now but return an error if the user tries to
change any of them.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The default value of x-check-cache-dropped is false. There's no reason
to use the previous value as a default in raw_reopen_prepare() because
bdrv_reopen_queue_child() already takes care of putting the old
options in the BDRVReopenState.options QDict.
If x-check-cache-dropped was previously set but is now missing from
the reopen QDict then it should be reset to false.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Image locking errors happening at device initialization time doesn't say
which file cannot be locked, for instance,
-device scsi-disk,drive=drive-1: Failed to get shared "write" lock
Is another process using the image?
could refer to either the overlay image or its backing image.
Hoist the error_append_hint to the caller of raw_check_lock_bytes where
file name is known, and include it in the error hint.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There is a rare case which the size of last compressed cluster
is larger than the cluster size, which will cause the file is
not aligned at the sector boundary.
There are three reasons to do it. First, if vmdk doesn't align at
the sector boundary, there may be many undefined behaviors,
such as, in vbox it will show VMDK: Compressed image is corrupted
'syno-vm-disk1.vmdk' (VERR_ZIP_CORRUPTED) when we try to import an
ova with unaligned vmdk. Second, all the cluster_sector is aligned
to sector, the last one should be like this, too. Third, it ease
reading with sector based I/Os.
Signed-off-by: yuchenlin <yuchenlin@synology.com>
Message-Id: <20180913082952.3675-1-yuchenlin@synology.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
- Deprecate the "enforce-config-section" machine parameter
- Re-enable the wdt_ib700, endianness and vmxnet3 qtests
- Some trivial fixes and doc update patches that crossed my way
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dXgp
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2018-09-25' into staging
- Deprecate the usage of a network backend via "name" instead of "id"
- Deprecate the "enforce-config-section" machine parameter
- Re-enable the wdt_ib700, endianness and vmxnet3 qtests
- Some trivial fixes and doc update patches that crossed my way
# gpg: Signature made Tue 25 Sep 2018 16:58:42 BST
# gpg: using RSA key 2ED9D774FE702DB5
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>"
# gpg: aka "Thomas Huth <thuth@redhat.com>"
# gpg: aka "Thomas Huth <huth@tuxfamily.org>"
# gpg: aka "Thomas Huth <th.huth@posteo.de>"
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2018-09-25:
Revert "check: Move VMXNET3 test to common"
Revert "check: Move endianess test to common"
Revert "check: Move wdt_ib700 test to common"
tests/migration: Speed up the test on ppc64
hw/qdev-core: Fix description of instance_init
qdev: fix a typo in comment
docs: Fix some typos (most found by codespell)
trivial: Make bios files and source files non-executable
memfd: fix possible usage of the uninitialized file descriptor
hw/core/machine: Officially deprecate the enforce-config-section parameter
net/slirp: Deprecate the [hub_id name] parameter tuple
net: Deprecate the "name" parameter of -net
Makefile: Add missing dependency for qemu-deprecated.texi
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These files can not be executed on the host, so they should not be
marked as executable.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When draining a block node, we recurse to its parent and for subtree
drains also to its children. A single AIO_WAIT_WHILE() is then used to
wait for bdrv_drain_poll() to become true, which depends on all of the
nodes we recursed to. However, if the respective child or parent becomes
quiescent and calls bdrv_wakeup(), only the AioWait of the child/parent
is checked, while AIO_WAIT_WHILE() depends on the AioWait of the
original node.
Fix this by using a single AioWait for all callers of AIO_WAIT_WHILE().
This may mean that the draining thread gets a few more unnecessary
wakeups because an unrelated operation got completed, but we already
wake it up when something _could_ have changed rather than only if it
has certainly changed.
Apart from that, drain is a slow path anyway. In theory it would be
possible to use wakeups more selectively and still correctly, but the
gains are likely not worth the additional complexity. In fact, this
patch is a nice simplification for some places in the code.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
bdrv_drain_poll_top_level() was buggy because it didn't release the
AioContext lock of the node to be drained before calling aio_poll().
This way, callbacks called by aio_poll() would possibly take the lock a
second time and run into a deadlock with a nested AIO_WAIT_WHILE() call.
However, it turns out that the aio_poll() call isn't actually needed any
more. It was introduced in commit 91af091f92, which is effectively
reverted by this patch. The cases it was supposed to fix are now covered
by bdrv_drain_poll(), which waits for block jobs to reach a quiescent
state.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Request callbacks can do pretty much anything, including operations that
will yield from the coroutine (such as draining the backend). In that
case, a decreased in_flight would be visible to other code and could
lead to a drain completing while the callback hasn't actually completed
yet.
Note that reordering these operations forbids calling drain directly
inside an AIO callback. As Paolo explains, indirectly calling it is
okay:
- Calling it through a coroutine is okay, because then
bdrv_drained_begin() goes through bdrv_co_yield_to_drain() and you
have in_flight=2 when bdrv_co_yield_to_drain() yields, then soon
in_flight=1 when the aio_co_wake() in the AIO callback completes, then
in_flight=0 after the bottom half starts.
- Calling it through a bottom half would be okay too, as long as the AIO
callback remembers to do inc_in_flight/dec_in_flight just like
bdrv_co_yield_to_drain() and bdrv_co_drain_bh_cb() do
A few more important cases that come to mind:
- A coroutine that yields because of I/O is okay, with a sequence
similar to bdrv_co_yield_to_drain().
- A coroutine that yields with no I/O pending will correctly decrease
in_flight to zero before yielding.
- Calling more AIO from the callback won't overflow the counter just
because of mutual recursion, because AIO functions always yield at
least once before invoking the callback.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
blk_unref() first decreases the refcount of the BlockBackend and calls
blk_delete() if the refcount reaches zero. Requests can still be in
flight at this point, they are only drained during blk_delete():
At this point, arbitrary callbacks can run. If any callback takes a
temporary BlockBackend reference, it will first increase the refcount to
1 and then decrease it to 0 again, triggering another blk_delete(). This
will cause a use-after-free crash in the outer blk_delete().
Fix it by draining the BlockBackend before decreasing to refcount to 0.
Assert in blk_ref() that it never takes the first refcount (which would
mean that the BlockBackend is already being deleted).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
A bdrv_drain operation must ensure that all parents are quiesced, this
includes BlockBackends. Otherwise, callbacks called by requests that are
completed on the BDS layer, but not quite yet on the BlockBackend layer
could still create new requests.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
bdrv_do_drained_begin/end() assume that they are called with the
AioContext lock of bs held. If we call drain functions from a coroutine
with the AioContext lock held, we yield and schedule a BH to move out of
coroutine context. This means that the lock for the home context of the
coroutine is released and must be re-acquired in the bottom half.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
In qemu_laio_process_completions_and_submit, the AioContext is acquired
before the ioq_submit iteration and after qemu_laio_process_completions,
but the latter is not thread safe either.
This change avoids a number of random crashes when the Main Thread and
an IO Thread collide processing completions for the same AioContext.
This is an example of such crash:
- The IO Thread is trying to acquire the AioContext at aio_co_enter,
which evidences that it didn't lock it before:
Thread 3 (Thread 0x7fdfd8bd8700 (LWP 36743)):
#0 0x00007fdfe0dd542d in __lll_lock_wait () at ../nptl/sysdeps/unix/sysv/linux/x86_64/lowlevellock.S:135
#1 0x00007fdfe0dd0de6 in _L_lock_870 () at /lib64/libpthread.so.0
#2 0x00007fdfe0dd0cdf in __GI___pthread_mutex_lock (mutex=mutex@entry=0x5631fde0e6c0)
at ../nptl/pthread_mutex_lock.c:114
#3 0x00005631fc0603a7 in qemu_mutex_lock_impl (mutex=0x5631fde0e6c0, file=0x5631fc23520f "util/async.c", line=511) at util/qemu-thread-posix.c:66
#4 0x00005631fc05b558 in aio_co_enter (ctx=0x5631fde0e660, co=0x7fdfcc0c2b40) at util/async.c:493
#5 0x00005631fc05b5ac in aio_co_wake (co=<optimized out>) at util/async.c:478
#6 0x00005631fbfc51ad in qemu_laio_process_completion (laiocb=<optimized out>) at block/linux-aio.c:104
#7 0x00005631fbfc523c in qemu_laio_process_completions (s=s@entry=0x7fdfc0297670)
at block/linux-aio.c:222
#8 0x00005631fbfc5499 in qemu_laio_process_completions_and_submit (s=0x7fdfc0297670)
at block/linux-aio.c:237
#9 0x00005631fc05d978 in aio_dispatch_handlers (ctx=ctx@entry=0x5631fde0e660) at util/aio-posix.c:406
#10 0x00005631fc05e3ea in aio_poll (ctx=0x5631fde0e660, blocking=blocking@entry=true)
at util/aio-posix.c:693
#11 0x00005631fbd7ad96 in iothread_run (opaque=0x5631fde0e1c0) at iothread.c:64
#12 0x00007fdfe0dcee25 in start_thread (arg=0x7fdfd8bd8700) at pthread_create.c:308
#13 0x00007fdfe0afc34d in clone () at ../sysdeps/unix/sysv/linux/x86_64/clone.S:113
- The Main Thread is also processing completions from the same
AioContext, and crashes due to failed assertion at util/iov.c:78:
Thread 1 (Thread 0x7fdfeb5eac80 (LWP 36740)):
#0 0x00007fdfe0a391f7 in __GI_raise (sig=sig@entry=6) at ../nptl/sysdeps/unix/sysv/linux/raise.c:56
#1 0x00007fdfe0a3a8e8 in __GI_abort () at abort.c:90
#2 0x00007fdfe0a32266 in __assert_fail_base (fmt=0x7fdfe0b84e68 "%s%s%s:%u: %s%sAssertion `%s' failed.\n%n", assertion=assertion@entry=0x5631fc238ccb "offset == 0", file=file@entry=0x5631fc23698e "util/iov.c", line=line@entry=78, function=function@entry=0x5631fc236adc <__PRETTY_FUNCTION__.15220> "iov_memset")
at assert.c:92
#3 0x00007fdfe0a32312 in __GI___assert_fail (assertion=assertion@entry=0x5631fc238ccb "offset == 0", file=file@entry=0x5631fc23698e "util/iov.c", line=line@entry=78, function=function@entry=0x5631fc236adc <__PRETTY_FUNCTION__.15220> "iov_memset") at assert.c:101
#4 0x00005631fc065287 in iov_memset (iov=<optimized out>, iov_cnt=<optimized out>, offset=<optimized out>, offset@entry=65536, fillc=fillc@entry=0, bytes=15515191315812405248) at util/iov.c:78
#5 0x00005631fc065a63 in qemu_iovec_memset (qiov=<optimized out>, offset=offset@entry=65536, fillc=fillc@entry=0, bytes=<optimized out>) at util/iov.c:410
#6 0x00005631fbfc5178 in qemu_laio_process_completion (laiocb=0x7fdd920df630) at block/linux-aio.c:88
#7 0x00005631fbfc523c in qemu_laio_process_completions (s=s@entry=0x7fdfc0297670)
at block/linux-aio.c:222
#8 0x00005631fbfc5499 in qemu_laio_process_completions_and_submit (s=0x7fdfc0297670)
at block/linux-aio.c:237
#9 0x00005631fbfc54ed in qemu_laio_poll_cb (opaque=<optimized out>) at block/linux-aio.c:272
#10 0x00005631fc05d85e in run_poll_handlers_once (ctx=ctx@entry=0x5631fde0e660) at util/aio-posix.c:497
#11 0x00005631fc05e2ca in aio_poll (blocking=false, ctx=0x5631fde0e660) at util/aio-posix.c:574
#12 0x00005631fc05e2ca in aio_poll (ctx=0x5631fde0e660, blocking=blocking@entry=false)
at util/aio-posix.c:604
#13 0x00005631fbfcb8a3 in bdrv_do_drained_begin (ignore_parent=<optimized out>, recursive=<optimized out>, bs=<optimized out>) at block/io.c:273
#14 0x00005631fbfcb8a3 in bdrv_do_drained_begin (bs=0x5631fe8b6200, recursive=<optimized out>, parent=0x0, ignore_bds_parents=<optimized out>, poll=<optimized out>) at block/io.c:390
#15 0x00005631fbfbcd2e in blk_drain (blk=0x5631fe83ac80) at block/block-backend.c:1590
#16 0x00005631fbfbe138 in blk_remove_bs (blk=blk@entry=0x5631fe83ac80) at block/block-backend.c:774
#17 0x00005631fbfbe3d6 in blk_unref (blk=0x5631fe83ac80) at block/block-backend.c:401
#18 0x00005631fbfbe3d6 in blk_unref (blk=0x5631fe83ac80) at block/block-backend.c:449
#19 0x00005631fbfc9a69 in commit_complete (job=0x5631fe8b94b0, opaque=0x7fdfcc1bb080)
at block/commit.c:92
#20 0x00005631fbf7d662 in job_defer_to_main_loop_bh (opaque=0x7fdfcc1b4560) at job.c:973
#21 0x00005631fc05ad41 in aio_bh_poll (bh=0x7fdfcc01ad90) at util/async.c:90
#22 0x00005631fc05ad41 in aio_bh_poll (ctx=ctx@entry=0x5631fddffdb0) at util/async.c:118
#23 0x00005631fc05e210 in aio_dispatch (ctx=0x5631fddffdb0) at util/aio-posix.c:436
#24 0x00005631fc05ac1e in aio_ctx_dispatch (source=<optimized out>, callback=<optimized out>, user_data=<optimized out>) at util/async.c:261
#25 0x00007fdfeaae44c9 in g_main_context_dispatch (context=0x5631fde00140) at gmain.c:3201
#26 0x00007fdfeaae44c9 in g_main_context_dispatch (context=context@entry=0x5631fde00140) at gmain.c:3854
#27 0x00005631fc05d503 in main_loop_wait () at util/main-loop.c:215
#28 0x00005631fc05d503 in main_loop_wait (timeout=<optimized out>) at util/main-loop.c:238
#29 0x00005631fc05d503 in main_loop_wait (nonblocking=nonblocking@entry=0) at util/main-loop.c:497
#30 0x00005631fbd81412 in main_loop () at vl.c:1866
#31 0x00005631fbc18ff3 in main (argc=<optimized out>, argv=<optimized out>, envp=<optimized out>)
at vl.c:4647
- A closer examination shows that s->io_q.in_flight appears to have
gone backwards:
(gdb) frame 7
#7 0x00005631fbfc523c in qemu_laio_process_completions (s=s@entry=0x7fdfc0297670)
at block/linux-aio.c:222
222 qemu_laio_process_completion(laiocb);
(gdb) p s
$2 = (LinuxAioState *) 0x7fdfc0297670
(gdb) p *s
$3 = {aio_context = 0x5631fde0e660, ctx = 0x7fdfeb43b000, e = {rfd = 33, wfd = 33}, io_q = {plugged = 0,
in_queue = 0, in_flight = 4294967280, blocked = false, pending = {sqh_first = 0x0,
sqh_last = 0x7fdfc0297698}}, completion_bh = 0x7fdfc0280ef0, event_idx = 21, event_max = 241}
(gdb) p/x s->io_q.in_flight
$4 = 0xfffffff0
Signed-off-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20180906130225.5118-8-jsnow@redhat.com
Reviewed-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
For purposes of minimum code movement, refactor the mirror_exit
callback to use the post-finalization callbacks in a trivial way.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20180906130225.5118-7-jsnow@redhat.com
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
[mreitz: Added comment for the mirror_exit() function]
Signed-off-by: Max Reitz <mreitz@redhat.com>
In cases where we abort the block/mirror job, there's no point in
installing the new backing chain before we finish aborting.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20180906130225.5118-6-jsnow@redhat.com
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Use the component callbacks; prepare, abort, and clean.
NB: prepare is only called when the job has not yet failed;
and abort can be called after prepare.
complete -> prepare -> abort -> clean
complete -> abort -> clean
During refactor, a potential problem with bdrv_drop_intermediate
was identified, the patched behavior is no worse than the pre-patch
behavior, so leave a FIXME for now to be fixed in a future patch.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20180906130225.5118-5-jsnow@redhat.com
Reviewed-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add support for taking and passing forward job creation flags.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 20180906130225.5118-4-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add support for taking and passing forward job creation flags.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 20180906130225.5118-3-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add support for taking and passing forward job creation flags.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 20180906130225.5118-2-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The sslverify setting is supposed to turn off all TLS certificate
checks in libcurl. However because of the way we use it, it only
turns off peer certificate authenticity checks
(CURLOPT_SSL_VERIFYPEER). This patch makes it also turn off the check
that the server name in the certificate is the same as the server
you're connecting to (CURLOPT_SSL_VERIFYHOST).
We can use Google's server at 8.8.8.8 which happens to have a bad TLS
certificate to demonstrate this:
$ ./qemu-img create -q -f qcow2 -b 'json: { "file.sslverify": "off", "file.driver": "https", "file.url": "https://8.8.8.8/foo" }' /var/tmp/file.qcow2
qemu-img: /var/tmp/file.qcow2: CURL: Error opening file: SSL: no alternative certificate subject name matches target host name '8.8.8.8'
Could not open backing image to determine size.
With this patch applied, qemu-img connects to the server regardless of
the bad certificate:
$ ./qemu-img create -q -f qcow2 -b 'json: { "file.sslverify": "off", "file.driver": "https", "file.url": "https://8.8.8.8/foo" }' /var/tmp/file.qcow2
qemu-img: /var/tmp/file.qcow2: CURL: Error opening file: The requested URL returned error: 404 Not Found
(The 404 error is expected because 8.8.8.8 is not actually serving a
file called "/foo".)
Of course the default (without sslverify=off) remains to always check
the certificate:
$ ./qemu-img create -q -f qcow2 -b 'json: { "file.driver": "https", "file.url": "https://8.8.8.8/foo" }' /var/tmp/file.qcow2
qemu-img: /var/tmp/file.qcow2: CURL: Error opening file: SSL: no alternative certificate subject name matches target host name '8.8.8.8'
Could not open backing image to determine size.
Further information about the two settings is available here:
https://curl.haxx.se/libcurl/c/CURLOPT_SSL_VERIFYPEER.htmlhttps://curl.haxx.se/libcurl/c/CURLOPT_SSL_VERIFYHOST.html
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Message-id: 20180914095622.19698-1-rjones@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
When we converted rbd to get rid of the older key/value-centric
encoding format, we broke compatibility with image files with backing
file strings encoded in the old format.
This leaves a bit of an ugly conundrum, and a hacky solution.
If the initial attempt to parse the "proper" options fails, it assumes
that we may have an older key/value encoded filename. Fall back to
attempting to parse the filename, and extract the required options from
it. If that fails, pass along the original error message.
We do not support mixed modern usage alongside legacy keyvalue pair
usage.
A deprecation warning has been added, although care should be taken
when actually deprecating since the impact is not limited to
commandline or qapi usage, but also opening existing images.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Message-id: 15b332e5432ad069441f7275a46080f465d789a0.1536704901.git.jcody@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
Code movement to pull the conversion from Qdict to BlockdevOptionsRbd
into a helper function.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Message-id: 5b49a980f2cde6610ab1df41bb0277d00b5db893.1536704901.git.jcody@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
Rename opaque_job to job to be consistent with other job implementations.
Rename 'job', the BackupBlockJob object, to 's' to also be consistent.
Suggested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20180830015734.19765-8-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Utilize the job_exit shim by not calling job_defer_to_main_loop, and
where applicable, converting the deferred callback into the job_exit
callback.
This converts backup, stream, create, and the unit tests all at once.
Most of these jobs do not see any changes to the order in which they
clean up their resources, except the test-blockjob-txn test, which
now puts down its bs before job_completed is called.
This is safe for the same reason the reordering in the mirror job is
safe, because job_completed no longer runs under two locks, making
the unref safe even if it causes a flush.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20180830015734.19765-7-jsnow@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Change the manual deferment to mirror_exit into the implicit
callback to job_exit and the mirror_exit callback.
This does change the order of some bdrv_unref calls and job_completed,
but thanks to the new context in which we call .exit, this is safe to
defer the possible flushing of any nodes to the job_finalize_single
cleanup stage.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20180830015734.19765-6-jsnow@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Change the manual deferment to commit_complete into the implicit
callback to job_exit, renaming commit_complete to commit_exit.
This conversion does change the timing of when job_completed is
called to after the bdrv_replace_node and bdrv_unref calls, which
could have implications for bjob->blk which will now be put down
after this cleanup.
Kevin highlights that we did not take any permissions for that backend
at job creation time, so it is safe to reorder these operations.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20180830015734.19765-5-jsnow@redhat.com
Reviewed-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Vladimir Sementsov-Ogievskiy