As the first step in adding support for the virtualization
extensions to the GICv3 emulation:
* add the necessary data fields to the state structures
* add the fields to the migration state, as a subsection
which is only present if virtualization is enabled
The use of a subsection means we retain migration
compatibility as EL2 is not enabled on any CPUs currently.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-8-git-send-email-peter.maydell@linaro.org
Add defines to gicv3_internal.h for fields in the ICH_*
system registers which form the GIC virtualization control
interface.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483977924-14522-7-git-send-email-peter.maydell@linaro.org
Add fields to the ARMCPU structure to allow CPU classes to
specify the configurable aspects of their GIC CPU interface.
In particular, the virtualization support allows different
values for number of list registers, priority bits and
preemption bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-6-git-send-email-peter.maydell@linaro.org
Wire the new VIRQ, VFIQ and maintenance interrupt lines from the
GIC to each CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-5-git-send-email-peter.maydell@linaro.org
The GICv3 support for virtualization includes an outbound
maintenance interrupt signal which is asserted when the
CPU interface wants to signal to the hypervisor that it
needs attention. Expose this as an outbound GPIO line from
the CPU object which can be wired up as a physical interrupt
line by the board code (as we do already for the CPU timers).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-4-git-send-email-peter.maydell@linaro.org
Augment the GIC's QOM device interface by adding two
new sets of sysbus IRQ lines, to signal VIRQ and VFIQ to
each CPU.
We never use these, but it's helpful to keep the v2-and-earlier
GIC's external interface in line with that of the GICv3 to
avoid board code having to add extra code conditional on which
version of the GIC is in use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-3-git-send-email-peter.maydell@linaro.org
Augment the GICv3's QOM device interface by adding two
new sets of sysbus IRQ lines, to signal VIRQ and VFIQ to
each CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-2-git-send-email-peter.maydell@linaro.org
Linux for arm64 v4.10 and later will complain if the ECAM config space is
not reserved in the ACPI namespace:
acpi PNP0A08:00: [Firmware Bug]: ECAM area [mem 0x3f000000-0x3fffffff] not reserved in ACPI namespace
The rationale is that OSes that don't consume the MCFG table should still
be able to infer that the PCI config space MMIO region is occupied.
So update the ACPI table generation routine to add this reservation.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1484328738-21149-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Using -cpu cortex-a9 (or any other unsupported CPU) with the virt
board will cause QEMU to segmentation fault. This bug was introduced
in commit 9ac4ef77, which incorrectly added a NULL terminator when
converting the VirtBoardInfo array into a simple array of strings
defining the valid CPUs. The cpuname_valid() loop already has
a termination condition based on ARRAY_SIZE, so the NULL is
spurious and causes the strcmp() to segfault if we reach it.
Delete the NULL.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1484619334-10488-1-git-send-email-zhaoshenglong@huawei.com
[PMM: expanded commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a ROM region, using the default size of the mapping window for
the CE0 FMC flash module, and fill it with the flash content.
This is a little hacky but until we can boot from a MMIO region, it
seems difficult to do anything else.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-11-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SMC controllers have a mode (Command mode) in which
accesses to the flash content are no different than doing MMIOs. The
controller generates all the necessary commands to load (or store)
data in memory.
So add a couple of tests doing direct reads and writes on the AHB bus.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-10-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's make sure when each test is run that the flash object is in an
initial state and did not keep configuration from the previous tests.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1483979087-32663-9-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SMC controllers have a mode (Command mode) in which
accesses to the flash content are no different than doing MMIOs. The
controller generates all the necessary commands to load (or store)
data in memory.
However, accesses are restricted to the segment window assigned the
the flash module by the controller. This window is defined by the
Segment Address Register.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-8-git-send-email-clg@kaod.org
[PMM: Deleted now-unused aspeed_smc_is_usermode() function]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SPI controller of the AST2400 SoC has less registers. So we can
adjust the size of the memory region holding the registers depending
on the controller type. We can also remove the guest_error logging
which is useless as the range of the region is strict enough.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1483979087-32663-7-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is getting difficult to read. Also add a 'has_dma' field for each
controller type.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-6-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On the AST2500 SoC, the FMC controller flash type is fixed to SPI for
CE0 and CE1 and 4BYTE mode is autodetected for CE0.
On the AST2400 SoC, the FMC controller flash type and 4BYTE mode are
strapped with register SCU70. We use the default settings from the
palmetto-bmc machine for now.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change the routines prototype to use a 'AspeedSMCFlash *' instead of
'AspeedSMCState *'. The result will help in making future changes
clearer.
Also change aspeed_smc_update_cs() which uselessly loops on all slave
devices to update their status.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead, we can simply set the irq level when unselecting the slave
devices. This change prepares ground for a subsequent cleanup of the
aspeed_smc_update_cs() routine which uselessly loops on all slaves to
update their status.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1483979087-32663-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is useless as reset will be called later on.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com>
Message-id: 1483979087-32663-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The DBGVCR_EL2 system register is needed to run a 32-bit
EL1 guest under a Linux EL2 64-bit hypervisor. Its only
purpose is to provide AArch64 with access to the state of
the DBGVCR AArch32 register. Since we only have a dummy
DBGVCR, implement a corresponding dummy DBGVCR32_EL2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
To run a VM in 32-bit EL1 our AArch32 interrupt handling code
needs to be able to cope with VIRQ and VFIQ exceptions.
These behave like IRQ and FIQ except that we don't need to try
to route them to Monitor mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
n25q00 and mt25q01 devices share the same JEDEC ID. The difference
between those two devices is number of dies and one bit in extended
JEDEC bytes. This commit adds proper entry for both devices by
introduction the number of dies and and new 25q00 entries.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-4-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modern big flash NOR devices consist of more than one die.
Some of them do not support chip erase and instead have a die
erase command that can erase one die only. This commit adds
support for defining the number of dies in the chip, and adds
support for die erase command.
The NOR flash model is not strict, so no option to
disable chip erase has been added.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-3-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some flash chips have additional page program opcode that
takes only 4 byte address. This commit adds support
for such command in Qemu.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-2-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The imx25 chip provides 3 i2c buses, but they have all been named
"i2c", which makes it difficult to predict which bus a device will
be connected to when specified on the command line.
This patch addresses the issue by naming the buses uniquely:
i2c-bus.0 i2c-bus.1 i2c-bus.2
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Message-id: 20170105043430.3176-2-alastair@au1.ibm.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current code seems to assume ring size is
always decreased but this is not required by spec:
what spec says is just that size can not exceed
the maximum. Fix it up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <1484256243-1982-1-git-send-email-mst@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently there're two functions, s390_pci_setup_msix() and
s390_pci_msix_init(), for msix initialization, and being called once
for each zpci device plugging. Let's integrate them.
Moreover msix is mandatory in s390 architecture. So we ensure the pci
device being plugged supports msix. For vfio (which is the only tested
setup so far), nothing changes.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The PCI bus number is usually set by the host during the enumeration.
In the s390 architecture we neither get a Device Tree nor have an
enumeration understanding bridge devices.
Let's fake the enumeration on reset and set the PCI_PRIMARY_BUS,
PCI_SECONDARY_BUS and PCI_SUBORDINATE_BUS config entries for the
bridges.
Let's add the configuration of these three config entries on bridge hot
plug.
The bus number is calculated based on a new entry, bus_num of the
S390pciState device.
This commit is inspired by what spapr pci does.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
After PCI multibus is supported, more than 32 PCI devices could be
plugged. The current implementation of s390_pci_find_dev_by_fh()
appears low performance if there's a huge number of PCI devices
plugged. Therefore we introduce a hashtable using idx as key to store
zpci device's pointer on account of translating fh to idx very easily.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When the hotplug handler detects a PCI bridge, the secondary bus has
been initialized by the core PCI code. We give the secondary bus the
bridge name and associate to it the IOMMU handling and
hotplug/hotunplug callbacks.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
A function may recursively call device search functions or may call
serveral different device search function. Passing the S390pciState to
search functions as an argument instead of looking up it inside the
search functions lowers the number of calling s390_get_phb().
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
In order to support a greater number of devices we use a QTAILQ
list of devices instead of a limited array.
This leads us to change:
- every lookup function s390_pci_find_xxx() for QTAILQ
- the FH_MASK_INDEX to index up to 65536 devices
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
When initializing a PCI device, an address space is required during PCI
core initialization and before the call to the embedding object hotplug
callback. To provide this AS, we allocate a S390PCIIOMMU object
containing this AS. Initialization of S390PCIIOMMU object is done
before the PCI device is completely created. So that we cannot
associate the IOMMU with the device at the moment. To track the IOMMU
object, we use g_hash functions with the PCI device's bus address as a
key to provide an array of pointers indexed by the PCI device's devfn
to the allocated IOMMU.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Currently S390PCIIOMMU is a normal struct. Let's make it inherit Object
in order to take advantage of QOM. In addition, we move some stuff
related to IOMMU from S390PCIBusDevice to S390PCIIOMMU.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's use kvm_gsi_routing_enabled() to check if kvm supports
KVM_CAP_IRQ_ROUTING in order to avoid a needless ioctl invocation.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We chain our compat handler via the CCW_COMPAT macros and via the
class_init function. (e.g. ccw_machine_2_7_class_options calls
ccw_machine_2_8_class_options). As all class_init functions in that
chain call SET_MACHINE_COMPAT for their compat settings, and
SET_MACHINE_COMPAT will append there is no need to do that again.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Commit 091a6b2ac fixed most of the memory leaks in failure
paths in net_init_tap() reported by Coverity (CID 1356216),
but missed one. Fix it by deferring the allocation of
fds and vhost_fds until after the error check.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
object_property_set_bool(OBJECT(dev), true, "realized", &err) in
pci_nic_init_nofail may release the object if device fails to
initialize which leads to use-after-free in error handling block.
qdev_init_nofail does the same thing while holding the reference.
(gdb) run -net nic
qemu-system-x86_64: failed to find romfile "efi-e1000.rom"
Program received signal SIGSEGV, Segmentation fault.
object_unparent (obj=0x7fffe96a0010) at qom/object.c:440
440 in qom/object.c
(gdb) bt
<nd_table>, rootbus=0x5555567ed990, default_model=<optimized out>,
default_devaddr=<optimized out>) at hw/pci/pci.c:1812
pci_bus=0x5555567ed990) at hw/i386/pc.c:1634
pci_type=0x555555c1a523 "i440FX", host_type=0x555555ba564e
"i440FX-pcihost") at hw/i386/pc_piix.c:241
out>, envp=<optimized out>) at vl.c:4481
Signed-off-by: Alex Kompel <barbos@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The dp8393x has several 32-bit values which are formed by concatenating
two 16 bit device register values. Attempting to do these inline
with ((s->reg[HI] << 16) | s->reg[LO]) can result in an unintended
sign extension because "x << 16" is of type 'int' even though s->reg
is unsigned, and so if the expression is used in a context where
it is cast to uint64_t the value is incorrectly sign-extended.
Fix this by using accessor functions with a uint32_t return type;
this also makes the code a bit easier to read.
This should fix Coverity issues 1307765, 1307766, 1307767, 1307768.
(To avoid having a ctda read function only used in a DPRINTF,
we move the DPRINTF down slightly so it can use the ttda function.)
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When running qemu-system-m68k with the "-net" parameter (for example
simply "-net nic -net user"), there is currently a confusing warning
message saying:
Warning: requested NIC (anonymous, model mcf_fec) was not created
(not supported by this machine?)
This seems to happen because the MCF NIC has never been adapted to
the currently expected QEMU device behavior. Thus let's QOMify the
NIC now to get rid of the warning message.
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Very simple loop optimization with a significant performance impact.
Microbenchmark results, modern x86-64:
buffer size | speed up
------------+---------
1500 | 1.7x
64 | 1.5x
8 | 1.15x
Microbenchmark results, POWER7:
buffer size | speed up
------------+---------
1500 | 5x
64 | 3.3x
8 | 1.13x
There is a lot of room for further improvement at the expense of
code complexity - aligned multibyte reads, LE/BE considerations,
architecture-specific optimizations, etc. This patch still keeps
things simple and readable.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Say it in another way to make it easier to understand.
Signed-off-by: Zhang Chen <zhangchen.fnst@cn.fujitsu.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This reverts commit 7ad9339e37.
The error "Failed to execute helper program (No such file or directory)"
is due to broken glib installation, missing windows gspawn helpers.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170104205722.26492-1-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Re-add the MacOSX/Darwin support:
Use the Intel HAX is kernel-based hardware acceleration module
(similar to KVM on Linux).
Based on the original "target/i386: Add Intel HAX to android emulator" patch
from David Chou <david.j.chou@intel.com> from emu-2.2-release branch in
the external/qemu-android repository.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <81b85c3032da902e73e77302af508b4b1a7c0ead.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the Intel HAX is kernel-based hardware acceleration module for
Windows (similar to KVM on Linux).
Based on the "target/i386: Add Intel HAX to android emulator" patch
from David Chou <david.j.chou@intel.com>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <7b9cae28a0c379ab459c7a8545c9a39762bd394f.1484045952.git.vpalatin@chromium.org>
[Drop hax_populate_ram stub. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
That's a forward port of the core HAX interface code from the
emu-2.2-release branch in the external/qemu-android repository as used by
the Android emulator.
The original commit was "target/i386: Add Intel HAX to android emulator"
saying:
"""
Backport of 2b3098ff27bab079caab9b46b58546b5036f5c0c
from studio-1.4-dev into emu-master-dev
Intel HAX (harware acceleration) will enhance android emulator performance
in Windows and Mac OS X in the systems powered by Intel processors with
"Intel Hardware Accelerated Execution Manager" package installed when
user runs android emulator with Intel target.
Signed-off-by: David Chou <david.j.chou@intel.com>
"""
It has been modified to build and run along with the current code base.
The formatting has been fixed to go through scripts/checkpatch.pl,
and the DPRINTF macros have been updated to get the instanciations checked by
the compiler.
The FPU registers saving/restoring has been updated to match the current
QEMU registers layout.
The implementation has been simplified by doing the following modifications:
- removing the code for supporting the hardware without Unrestricted Guest (UG)
mode (including all the code to fallback on TCG emulation).
- not including the Darwin support (which is not yet debugged/tested).
- simplifying the initialization by removing the leftovers from the Android
specific code, then trimming down the remaining logic.
- removing the unused MemoryListener callbacks.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <e1023837f8d0e4c470f6c4a3bf643971b2bca5be.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the generic cpu_synchronize_ functions to the common hw_accel.h header,
in order to prepare for the addition of a second hardware accelerator.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Message-Id: <f5c3cffe8d520011df1c2e5437bb814989b48332.1484045952.git.vpalatin@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are not needed since linux-headers/ provides up-to-date definitions.
The constants are in linux-headers/asm-powerpc/kvm.h.
The sole users, hw/intc/xics_kvm.c and target/ppc/kvm.c, include asm/kvm.h
via sysemu/kvm.h->linux/kvm.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We allow vhost to clear VIRITO_F_IOMMU_PLATFORM which is wrong since
VIRTIO_F_IOMMU_PLATFORM is mandatory for security. Fixing this by
enforce it after vdc->get_features().
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>