The qemu-ga documentation is currently in qemu-ga.texi in
Texinfo format, which we present to the user as:
* a qemu-ga manpage
* a section of the main qemu-doc HTML documentation
Convert the documentation to rST format, and present it to
the user as:
* a qemu-ga manpage
* part of the interop/ Sphinx manual
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Message-id: 20190905131040.8350-1-peter.maydell@linaro.org
Commit fe0480d6 and friends added BDRV_REQ_NO_FALLBACK as a way to
avoid wasting time on a preliminary write-zero request that will later
be rewritten by actual data, if it is known that the write-zero
request will use a slow fallback; but in doing so, could not optimize
for NBD. The NBD specification is now considering an extension that
will allow passing on those semantics; this patch updates the new
protocol bits and 'qemu-nbd --list' output to recognize the bit, as
well as the new errno value possible when using the new flag; while
upcoming patches will improve the client to use the feature when
present, and the server to advertise support for it.
The NBD spec recommends (but not requires) that ENOTSUP be avoided for
all but failures of a fast zero (the only time it is mandatory to
avoid an ENOTSUP failure is when fast zero is supported but not
requested during write zeroes; the questionable use is for ENOTSUP to
other actions like a normal write request). However, clients that get
an unexpected ENOTSUP will either already be treating it the same as
EINVAL, or may appreciate the extra bit of information. We were
equally loose for returning EOVERFLOW in more situations than
recommended by the spec, so if it turns out to be a problem in
practice, a later patch can tighten handling for both error codes.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190823143726.27062-3-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[eblake: tweak commit message, also handle EOPNOTSUPP]
The NBD specification defines NBD_FLAG_CAN_MULTI_CONN, which can be
advertised when the server promises cache consistency between
simultaneous clients (basically, rules that determine what FUA and
flush from one client are able to guarantee for reads from another
client). When we don't permit simultaneous clients (such as qemu-nbd
without -e), the bit makes no sense; and for writable images, we
probably have a lot more work before we can declare that actions from
one client are cache-consistent with actions from another. But for
read-only images, where flush isn't changing any data, we might as
well advertise multi-conn support. What's more, advertisement of the
bit makes it easier for clients to determine if 'qemu-nbd -e' was in
use, where a second connection will succeed rather than hang until the
first client goes away.
This patch affects qemu as server in advertising the bit. We may want
to consider patches to qemu as client to attempt parallel connections
for higher throughput by spreading the load over those connections
when a server advertises multi-conn, but for now sticking to one
connection per nbd:// BDS is okay.
See also: https://bugzilla.redhat.com/1708300
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190815185024.7010-1-eblake@redhat.com>
[eblake: tweak blockdev-nbd.c to not request shared when writable,
fix iotest 233]
Reviewed-by: John Snow <jsnow@redhat.com>
Move query-target and its return type TargetInfo from misc.json to
machine.json, where they are covered by MAINTAINERS section "Machine
core". Also move its implementation from arch_init.c to
hw/core/machine-qmp-cmds, where it is likewise covered.
All users of SysEmuTarget are now in machine.json. Move it there from
common.json.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-3-armbru@redhat.com>
The vhost-user specification does not explain when
VHOST_USER_PROTOCOL_F_MQ must be implemented. This may lead
implementors of vhost-user masters to believe that this protocol feature
is required for any device that has multiple virtqueues. That would be
a mistake since existing vhost-user slaves offer multiple virtqueues but
do not advertise VHOST_USER_PROTOCOL_F_MQ.
For example, a vhost-net device with one rx/tx queue pair is not
multiqueue. The slave does not need to advertise
VHOST_USER_PROTOCOL_F_MQ. Therefore the master must assume it has these
virtqueues and cannot rely on askingt the slave how many virtqueues
exist.
Extend the specification to explain the different between true
multiqueue and regular devices with a fixed virtqueue layout.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20190624091304.666-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
The annotated style json we use in QMP documentation is not strict json
and depending on the version of Sphinx (2.0+) or Pygments installed,
might cause the build to fail.
Use the new QMP lexer.
Further, some versions of Sphinx can not apply custom lexers to "code"
directives and require the use of "code-block" directives instead, so
make that change at this time as well.
Tested under:
- Sphinx 1.3.6 and Pygments 2.4
- Sphinx 1.7.6 and Pygments 2.2 (Fedora 29 packages)
- Sphinx 2.0.1 and Pygments 2.4
- Sphinx 3.0.0+/f396b3a783 and Pygments 2.4 (From Sphinx git c4f44bdd)
Reported-by: Aarushi Mehta <mehta.aaru20@gmail.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20190603214653.29369-4-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Pygments and Sphinx get pickier all the time; Sphinx 2.1+ now catches
these errors.
Signed-off-by: John Snow <jsnow@redhat.com>
Reported-by: Aarushi Mehta <mehta.aaru20@gmail.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190603214653.29369-2-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
The "Multiple queue support" section makes references to vhost-user-net
"queue pairs". This is confusing for two reasons:
1. This actually applies to all device types, not just vhost-user-net.
2. VHOST_USER_GET_QUEUE_NUM returns the number of virtqueues, not the
number of queue pairs.
Reword the section so that the vhost-user-net specific part is relegated
to the very end: we acknowledge that vhost-user-net historically
automatically enabled the first queue pair.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20190626074815.19994-5-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20190605131221.29432-1-marcandre.lureau@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a new vhost-user message to give a unix socket to a vhost-user
backend for GPU display updates.
Back when I started that work, I added a new GPU channel because the
vhost-user protocol wasn't bidirectional. Since then, there is a
vhost-user-slave channel for the slave to send requests to the master.
We could extend it with GPU messages. However, the GPU protocol is
quite orthogonal to vhost-user, thus I chose to have a new dedicated
channel.
See vhost-user-gpu.rst for the protocol details.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-2-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20190315180735.13096-1-marcandre.lureau@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This just about rewrites the entirety of the bitmaps.rst document to
make it consistent with the 4.0 release. I have added new features seen
in the 4.0 release, as well as tried to clarify some points that keep
coming up when discussing this feature both in-house and upstream.
It does not yet cover pull backups or migration details, but I intend to
keep extending this document to cover those cases.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190426221528.30293-3-jsnow@redhat.com
[Adjusted commit message. --js]
Signed-off-by: John Snow <jsnow@redhat.com>
This patch introduces two new messages VHOST_USER_GET_INFLIGHT_FD
and VHOST_USER_SET_INFLIGHT_FD to support transferring a shared
buffer between qemu and backend.
Firstly, qemu uses VHOST_USER_GET_INFLIGHT_FD to get the
shared buffer from backend. Then qemu should send it back
through VHOST_USER_SET_INFLIGHT_FD each time we start vhost-user.
This shared buffer is used to track inflight I/O by backend.
Qemu should retrieve a new one when vm reset.
Signed-off-by: Xie Yongji <xieyongji@baidu.com>
Signed-off-by: Chai Wen <chaiwen@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Message-Id: <20190228085355.9614-2-xieyongji@baidu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As discussed during "[PATCH v4 00/29] vhost-user for input & GPU"
review, let's define a common set of backend conventions to help with
management layer implementation, and interoperability.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190308140454.32437-3-marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We already use (we didn't notice it) IN_USE flag for marking bitmap
metadata outdated, such as AUTO flag, which mirrors enabled/disabled
bitmaps. Now we are going to support bitmap resize, so it's good to
write IN_USE meaning with more details.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190311185147.52309-2-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
The previous commit added a way to configure firmware with -blockdev
rather than -drive if=pflash. Document it as the preferred way.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190308131445.17502-13-armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Be more specific about the string representation in header extensions.
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
By default Sphinx wants to build a single manual at once.
For QEMU, this doesn't suit us, because we want to have
separate manuals for "Developer's Guide", "User Manual",
and so on, and we don't want to ship the Developer's Guide
to end-users. However, we don't want to completely duplicate
conf.py for each manual, and we'd like to continue to
support "build all docs in one run" for third-party sites
like readthedocs.org.
Make the top-level conf.py support two usage forms:
(1) as a common config file which is included by the conf.py
for each of QEMU's manuals: in this case sphinx-build is run
multiple times, once per subdirectory.
(2) as a top level conf file which will result in building all
the manuals into a single document: in this case sphinx-build is
run once, on the top-level docs directory.
Provide per-manual conf.py files and top level pages for
our first two manuals:
* QEMU Developer's Guide (docs/devel)
* QEMU System Emulation Management and Interoperability Guide
(docs/interop)
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-id: 20190305172139.32662-9-peter.maydell@linaro.org
Message-id: 20190228145624.24885-9-peter.maydell@linaro.org
It can be useful to figure out which NBD protocol features are
exposed by a server, as well as what features a client will
take advantage of if available, for a given qemu release. It's
not always precise to base features on version numbers (thanks
to downstream backports), but any documentation is better than
making users search through git logs themselves.
This patch originally stemmed from a request to document that
pristine 3.0 has a known bug where NBD_OPT_LIST_META_CONTEXT
with 0 queries forgot to advertise an available
"qemu:dirty-bitmap" context, but documenting bugs like this (or
the fact that 3.0 also botched NBD_CMD_CACHE) gets to be too
much details, especially since buggy releases will be less
likely connection targets over time. Instead, I chose to just
remind users to check stable release branches.
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181215135324.152629-3-eblake@redhat.com>
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
RFC8259 obsoletes RFC7159. Fix a couple of URLs to point to the
newer version.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181203175702.128701-1-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
When a QMP client sends in-band commands more quickly that we can
process them, we can either queue them without limit (QUEUE), drop
commands when the queue is full (DROP), or suspend receiving commands
when the queue is full (SUSPEND). None of them is ideal:
* QUEUE lets a misbehaving client make QEMU eat memory without bounds.
Not such a hot idea.
* With DROP, the client has to cope with dropped in-band commands. To
inform the client, we send a COMMAND_DROPPED event then. The event is
flawed by design in two ways: it's ambiguous (see commit d621cfe0a1),
and it brings back the "eat memory without bounds" problem.
* With SUSPEND, the client has to manage the flow of in-band commands to
keep the monitor available for out-of-band commands.
We currently DROP. Switch to SUSPEND.
Managing the flow of in-band commands to keep the monitor available for
out-of-band commands isn't really hard: just count the number of
"outstanding" in-band commands (commands sent minus replies received),
and if it exceeds the limit, hold back additional ones until it drops
below the limit again.
Note that we need to be careful pairing the suspend with a resume, or
else the monitor will hang, possibly forever. And here since we need to
make sure both:
(1) popping request from the req queue, and
(2) reading length of the req queue
will be in the same critical section, we let the pop function take the
corresponding queue lock when there is a request, then we release the
lock from the caller.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20181009062718.1914-2-peterx@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Although off_t permits up to 63 bits (8EB) of file offsets, in
practice, we're going to hit other limits first. Document some
of those limits in the qcow2 spec (some are inherent, others are
implementation choices of qemu), and how choice of cluster size
can influence some of the limits.
While we cannot map any uncompressed virtual cluster to any
address higher than 64 PB (56 bits) (due to the current L1/L2
field encoding stopping at bit 55), qemu's cap of 8M for the
refcount table can still access larger host addresses for some
combinations of large clusters and small refcount_order. For
comparison, ext4 with 4k blocks caps files at 16PB.
Another interesting limit: for compressed clusters, the L2 layout
requires an ever-smaller maximum host offset as cluster size gets
larger, down to a 512 TB maximum with 2M clusters. In particular,
note that with a cluster size of 8k or smaller, the L2 entry for
a compressed cluster could technically point beyond the 64PB mark,
but when you consider that with 8k clusters and refcount_order = 0,
you cannot access beyond 512T without exceeding qemu's limit of an
8M cap on the refcount table, it is unlikely that any image in the
wild has attempted to do so. To be safe, let's document that bits
beyond 55 in a compressed cluster must be 0.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's the same as -no-user-config and marked as deprecated since three
releases already. Time to remove it now.
Acked-by: Peter Krempa <pkrempa@redhat.com>
Acked-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Section "QGA Synchronization" specifies that sending "a raw 0xFF
sentinel byte" makes the server "reset its state and discard all
pending data prior to the sentinel." What actually happens there is a
lexical error, which will produce one or more error responses.
Moreover, it's not specific to QGA.
Create new section "Forcing the JSON parser into known-good state" to
document the technique properly. Rewrite section "QGA
Synchronization" to document just the other direction, i.e. command
guest-sync-delimited.
Section "Protocol Specification" mentions "synchronization bytes
(documented below)". Delete that.
While there, fix it not to claim '"Server" is QEMU itself', but
'"Server" is either QEMU or the QEMU Guest Agent'.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20180823164025.12553-2-armbru@redhat.com>
Signed-off-by: Ville Skyttä <ville.skytta@iki.fi>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20180612065150.21110-1-ville.skytta@iki.fi
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit cf869d5317 "qmp: support out-of-band (oob) execution" added a
general mechanism for command-independent arguments just for an
out-of-band flag:
The "control" key is introduced to store this extra flag. "control"
field is used to store arguments that are shared by all the commands,
rather than command specific arguments. Let "run-oob" be the first.
However, it failed to reject unknown members of "control". For
instance, in QMP command
{"execute": "query-name", "id": 42, "control": {"crap": true}}
"crap" gets silently ignored.
Instead of fixing this, revert the general "control" mechanism
(because YAGNI), and do it the way I initially proposed, with key
"exec-oob". Simpler code, simpler interface.
An out-of-band command
{"execute": "migrate-pause", "id": 42, "control": {"run-oob": true}}
becomes
{"exec-oob": "migrate-pause", "id": 42}
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20180703085358.13941-13-armbru@redhat.com>
[Commit message typo fixed]
Commit cf869d5317 "qmp: support out-of-band (oob) execution" made
"id" mandatory for all commands when the client accepted capability
"oob". This is rather onerous when you play with QMP by hand, and
unnecessarily so: only out-of-band commands need an ID for reliable
matching of response to command.
Revert that part of commit cf869d5317 for now, but have documentation
advise on the need to use "id" with out-of-band commands.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180703085358.13941-8-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
OOB documentation is spread over qmp-spec.txt sections 2.2.1
Capabilities and 2.3 Issuing Commands. The amount of detail is a bit
distracting there. Move the meat of the matter to new section 2.3.1
Out of band execution.
Throw in a few other improvements while there:
* 2.2 Server Greeting: Drop advice to search entire capabilities
array; should be obvious.
* 3. QMP Examples
- 3.1 Server Greeting: Update greeting to the one we expect for the
release. Now shows capability "oob". Update qmp-intro.txt
likewise.
- 3.2 Capabilities negotiation: Show client accepting capability
"oob".
- 3.7 Out-of-band execution: New.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20180703085358.13941-4-armbru@redhat.com>
[Whitespace tidied up]
Affects documentation and a few error messages.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20180703085358.13941-2-armbru@redhat.com>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a schema that describes the different uses and properties of virtual
machine firmware.
Each firmware executable installed on a host system should come with at
least one JSON file that conforms to this schema. Each file informs the
management applications about
- the firmware's properties and one possible use case / feature set,
- configuration bits that are required to run the firmware binary.
In addition, define rules for management apps for picking the highest
priority firmware JSON file when multiple such files match the search
criteria.
Cc: "Daniel P. Berrange" <berrange@redhat.com>
Cc: David Gibson <dgibson@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Kashyap Chamarthy <kchamart@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Thomas Huth <thuth@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20180509152608.9343-1-lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch introduces VHOST_USER_PROTOCOL_F_HOST_NOTIFIER.
With this feature negotiated, vhost-user backend can register
memory region based host notifiers. And it will allow the guest
driver in the VM to notify the hardware accelerator at the
vhost-user backend directly.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce VHOST_USER_PROTOCOL_F_SLAVE_SEND_FD protocol
feature to allow slave to send at most 8 descriptors
in each message to master via ancillary data using the
slave channel.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Compressed clusters are not supposed to have the COPIED bit set, but
this is not made explicit in the specs, so let's document it.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 74552e1d6e858d3159cb0c0e188e80bc9248e337.1523376013.git.berto@igalia.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Without a dedicated protocol feature, QEMU cannot know whether
the backend can handle VHOST_USER_SET_CONFIG and
VHOST_USER_GET_CONFIG messages.
This patch adds a protocol feature that is only advertised by
QEMU if the device implements the config ops. Vhost user init
fails if the device support the feature but the backend doesn't.
The backend should only send VHOST_USER_SLAVE_CONFIG_CHANGE_MSG
requests if the protocol feature has been negotiated.
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Changpeng Liu <changpeng.liu@intel.com>
This message is sent just before the end of postcopy to get the
client to stop using userfault since we wont respond to any more
requests. It should close userfaultfd so that any other pages
get mapped to the backing file automatically by the kernel, since
at this point we know we've received everything.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We need a better way, but at the moment we need the address of the
mappings sent back to qemu so it can interpret the messages on the
userfaultfd it reads.
This is done as a 3 stage set:
QEMU -> client
set_mem_table
mmap stuff, get addresses
client -> qemu
here are the addresses
qemu -> client
OK - now you can use them
That ensures that qemu has registered the new addresses in it's
userfault code before the client starts accessing them.
Note: We don't ask for the default 'ack' reply since we've got our own.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Notify the vhost-user slave on reception of the 'postcopy-listen'
event from the source.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Wire up a notifier to send a VHOST_USER_POSTCOPY_ADVISE
message on an incoming advise.
Later patches will fill in the behaviour/contents of the
message.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a vhost feature flag for postcopy support, and
use the postcopy notifier to check it before allowing postcopy.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Update both the developer and spec for the new QMP OOB (Out-Of-Band)
command.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20180309090006.10018-2-peterx@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: grammar tweaks]
Signed-off-by: Eric Blake <eblake@redhat.com>
-----BEGIN PGP SIGNATURE-----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=2axz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches
# gpg: Signature made Mon 05 Mar 2018 17:45:51 GMT
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (38 commits)
block: Fix NULL dereference on empty drive error
qcow2: Replace align_offset() with ROUND_UP()
block/ssh: Add basic .bdrv_truncate()
block/ssh: Make ssh_grow_file() blocking
block/ssh: Pull ssh_grow_file() from ssh_create()
qemu-img: Make resize error message more general
qcow2: make qcow2_co_create2() a coroutine_fn
block: rename .bdrv_create() to .bdrv_co_create_opts()
Revert "IDE: Do not flush empty CDROM drives"
block: test blk_aio_flush() with blk->root == NULL
block: add BlockBackend->in_flight counter
block: extract AIO_WAIT_WHILE() from BlockDriverState
aio: rename aio_context_in_iothread() to in_aio_context_home_thread()
docs: document how to use the l2-cache-entry-size parameter
specs/qcow2: Fix documentation of the compressed cluster descriptor
iotest 033: add misaligned write-zeroes test via truncate
block: fix write with zero flag set and iovector provided
block: Drop unused .bdrv_co_get_block_status()
vvfat: Switch to .bdrv_co_block_status()
vpc: Switch to .bdrv_co_block_status()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# include/block/block.h
Move qapi-schema.json to qapi/, so it's next to its modules, and all
files get generated to qapi/, not just the ones generated for modules.
Consistently name the generated files qapi-MODULE.EXT:
qmp-commands.[ch] become qapi-commands.[ch], qapi-event.[ch] become
qapi-events.[ch], and qmp-introspect.[ch] become qapi-introspect.[ch].
This gets rid of the temporary hacks in scripts/qapi/commands.py,
scripts/qapi/events.py, and scripts/qapi/common.py.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-28-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[eblake: Fix trailing dot in tpm.c, undo temporary hack for OSX toolchain]
Signed-off-by: Eric Blake <eblake@redhat.com>
* Fix guidance on error classes
* Point to generated documentation
* Drop plea for documentation, because the QAPI code generator
enforces it since commit 3313b6124b
* Minor tweaks here and there
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-27-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Peter Maydell