I've run into a compilation error today with the current version of GCC 8:
In file included from s390-ccw.h:49,
from main.c:12:
cio.h:128:1: error: alignment 1 of 'struct tpi_info' is less than 4 [-Werror=packed-not-aligned]
} __attribute__ ((packed));
^
cc1: all warnings being treated as errors
Since the struct tpi_info contains an element ("struct subchannel_id schid")
which is marked as aligned(4), we've got to mark the struct tpi_info as
aligned(4), too.
CC: qemu-stable@nongnu.org
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1525774672-11913-1-git-send-email-thuth@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
s390-ccw.img contains fixes for the boot menu, and s390-netboot.img
contains the support for .INS files and the patch for resetting the
machine with diag308.
Signed-off-by: Thomas Huth <thuth@redhat.com>
We currently pass an integer as the subcode parameter. However,
the upper bits of the register containing the subcode need to
be 0, which is not guaranteed unless we explicitly specify the
subcode to be an unsigned long value.
Fixes: d046c51dad ("pc-bios/s390-ccw: Get device address via diag 308/6")
Cc: qemu-stable@nongnu.org
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The .INS config files can normally be found on CD-ROM ISO images,
so by supporting these files, it is now possible to boot directly
when the TFTP server is set up with the contents of such an CD-ROM
image.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The netboot firmware so far simply jumped directly into the OS kernel
after the download has been completed. This, however, bears the risk
that the virtio-net device still might be active in the background and
incoming packets are still placed into the buffers - which could destroy
memory of the now-running Linux kernel in case it did not take over the
device fast enough. Also the SCLP console is not put into a well-defined
state here. We should hand over the system in a clean state when jumping
into the kernel, so let's use the same mechanism as it's done in the
main s390-ccw firmware and reset the machine with diag308 into a clean
state before jumping into the OS kernel code. To be able to share the
code with the main s390-ccw firmware, the related functions are now
extracted from bootmap.c into a new file called jump2ipl.c.
Since we now also set the boot device schid at address 184 for the network
boot device, this patch also slightly changes the way how we detect the
entry points for non-ELF binary images: The code now looks for the "S390EP"
magic first and then jumps to 0x10000 in case it has been found. This is
necessary for booting from network devices, since the normal kernel code
(where the PSW at ddress 0 points to) tries to do a block load from the
boot device. This of course fails for a virtio-net device and causes the
kernel to abort with a panic-PSW silently.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When we want to support pxelinux-style network booting later, we've got
to do several TFTP transfers - and we do not want to apply for a new IP
address via DHCP each time. So split up net_load into three parts:
1. net_init(), which initializes virtio-net, gets an IP address via DHCP
and prints out the related information.
2. The tftp_load call is now moved directly into the main() function
3. A new net_release() function which should tear down the network stack
before we are done in the firmware.
This will make it easier to extend the code in the next patches.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
zIPL boot menu entries can be non-sequential. Let's account
for this issue for the s390 enumerated boot menu. Since we
can no longer print a range of available entries to the
user, we have to present a list of each available entry.
An example of this menu:
s390-ccw Enumerated Boot Menu.
[0] default
[1]
[2]
[7]
[8]
[9]
[11]
[12]
Please choose:
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reported-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
zIPL boot menu entries can be non-sequential. Let's account
for this issue for the s390 zIPL boot menu. Since this boot
menu is actually an imitation and is not completely capable
of everything the real zIPL menu can do, let's also print a
different banner to the user.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reported-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Rename the loadparm char array in main.c to loadparm_str and
increased the size by one byte to account for a null termination
when converting the loadparm string to an int via atoui. We
also allow the boot menu to be enabled when loadparm is set to
an empty string or a series of spaces.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reported-by: Vasily Gorbik <gor@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The MAX_TABLE_ENTRIES constant has a name that is too generic. As we
want to declare a limit for boot menu entries, let's rename it to a more
fitting MAX_BOOT_ENTRIES and set its value to 31 (30 boot entries and
1 default entry). Also we move it from bootmap.h to s390-ccw.h to make
it available for menu.c in a later patch.
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
"size_t" should be an unsigned type according to the C standard.
Thus we should also use this convention in the s390-ccw firmware to avoid
confusion. I checked the sources, and apart from one spot in libc.c, the
code should all be fine with this change.
Buglink: https://bugs.launchpad.net/qemu/+bug/1753437
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Contains the following commits:
- s390: Do not pass inofficial IPL type to the guest
For s390-netboot.img, this also contains the following commits (update
was forgotten last time):
- pc-bios/s390-ccw: Move string arrays from bootmap header to .c file
- pc-bios/s390-ccw: Increase virtio timeout to 30 seconds
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
IPL over a virtio-scsi device requires special handling not
available in the real architecture. For this purpose the IPL
type 0xFF has been chosen as means of communication between
QEMU and the pc-bios. However, a guest OS could be confused
by seeing an unknown IPL type.
This change sets the IPL parameter type to 0x02 (CCW) to prevent
this. Pre-existing Linux has looked up the IPL parameters only in
the case of FCP IPL. This means that the behavior should stay
the same even if Linux checks for the IPL type unconditionally.
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Message-Id: <1522940844-12336-4-git-send-email-mihajlov@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The current timeout is set to only three seconds - and considering that
vring_wait_reply() or rather get_second() is not doing any rounding,
the real timeout is likely rather 2 seconds in most cases. When the
host is really badly loaded, it's possible that we hit this timeout by
mistake; it's even more likely if we run the guest in TCG mode instead
of KVM.
So let's increase the timeout to 30 seconds instead to ease this situation
(30 seconds is also the timeout that is used by the Linux SCSI subsystem
for example, so this seems to be a sane value for block IO timeout).
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1549079
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1522316251-16399-1-git-send-email-thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
[CH: tweaked commit message]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
git shortlog rel-1.11.0..rel-1.11.1
===================================
Kevin O'Connor (3):
build: Use git describe --always
shadow: Don't invoke a shutdown on reboot unless in a reboot loop
paravirt: Only enable sercon in NOGRAPHIC mode if no other console specified
Marcel Apfelbaum (1):
pci: fix 'io hints' capability for RedHat PCI bridges
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
SeaBIOS blob which is currently shipped with QEMU
doesn't need acpi-dsdt.aml nor is able to use it
and code that loaded it in QEMU was removed by
(commit 9fb7aaaf4c "pc: drop external DSDT loading")
in 2013.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
bootmap.h can currently only be included once - otherwise the linker
complains about multiple definitions of the "magic" strings. It's a
bad style to define string arrays in header files, so let's better
move these to the bootmap.c file instead where they are used.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1520317081-5341-1-git-send-email-thuth@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Add emulation of aCube Sam460ex board based on AMCC 460EX embedded SoC.
This is not a complete implementation yet with a lot of components
still missing but enough for the U-Boot firmware to start and to boot
a Linux kernel or AROS.
Signed-off-by: François Revol <revol@free.fr>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Provide a new s390-ccw.img binary with the boot menu patches by Collin.
Though there should not be any visible changes for the network booting,
the s390-netboot.img binary has been rebuilt, too, since some of the
changes affected the shared source files.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Interactive boot menu for scsi. This follows a similar procedure
as the interactive menu for eckd dasd. An example follows:
s390x Enumerated Boot Menu.
3 entries detected. Select from index 0 to 2.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Added additional "break;" statement to avoid analyzer warnings]
Signed-off-by: Thomas Huth <thuth@redhat.com>
If no boot menu options are present, then flag the boot menu to
use the zipl options that were set in the zipl configuration file
(and stored on disk by zipl). These options are found at some
offset prior to the start of the zipl boot menu banner. The zipl
timeout value is limited to a 16-bit unsigned integer and stored
as seconds, so we take care to convert it to milliseconds in order
to conform to the rest of the boot menu functionality. This is
limited to CCW devices.
For reference, the zipl configuration file uses the following
fields in the menu section:
prompt=1 enable the boot menu
timeout=X set the timeout to X seconds
To explicitly disregard any boot menu options, then menu=off or
<bootmenu enable='no' ... /> must be specified.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It is possible while waiting for multiple types of external
interrupts that we might have pending irqs remaining between
irq consumption and irq-type disabling. Those interrupts
could potentially propagate to the guest after IPL completes
and cause unwanted behavior.
As it is today, the SCLP will only recognize write events that
are enabled by the control program's send and receive masks. To
limit the window for, and prevent further irqs from, ASCII
console events (specifically keystrokes), we should only enable
the control program's receive mask when we need it.
While we're at it, remove assignment of the (non control program)
send and receive masks, as those are actually set by the SCLP.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Implements an sclp_read function to capture input from the
console and a wrapper function that handles parsing certain
characters and adding input to a buffer. The input is checked
for any erroneous values and is handled appropriately.
A prompt will persist until input is entered or the timeout
expires (if one was set). Example:
Please choose (default will boot in 10 seconds):
Correct input will boot the respective boot index. If the
user's input is empty, 0, or if the timeout expires, then
the default zipl entry will be chosen. If the input is
within the range of available boot entries, then the
selection will be booted. Any erroneous input will cancel
the timeout and re-prompt the user.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
When the boot menu options are present and the guest's
disk has been configured by the zipl tool, then the user
will be presented with an interactive boot menu with
labeled entries. An example of what the menu might look
like:
zIPL v1.37.1-build-20170714 interactive boot menu.
0. default (linux-4.13.0)
1. linux-4.13.0
2. performance
3. kvm
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Read the stage2 boot loader data block-by-block. We scan the
current block for the string "zIPL" to detect the start of the
boot menu banner. We then load the adjacent blocks (previous
block and next block) to account for the possibility of menu
data spanning multiple blocks.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reads boot menu flag and timeout values from the iplb and
sets the respective fields for the menu.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Set boot menu options for an s390 guest and store them in
the iplb. These options are set via the QEMU command line
option:
-boot menu=on|off[,splash-time=X]
or via the libvirt domain xml:
<os>
<bootmenu enable='yes|no' timeout='X'/>
</os>
Where X represents some positive integer representing
milliseconds.
Any value set for loadparm will override all boot menu options.
If loadparm=PROMPT, then the menu will be enabled without a
timeout.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The s390-ccw firmware needs some information in support of the
boot process which is not available on the native machine.
Examples are the netboot firmware load address and now the
boot menu parameters.
While storing that data in unused fields of the IPL parameter block
works, that approach could create problems if the parameter block
definition should change in the future. Because then a guest could
overwrite these fields using the set IPLB diagnose.
In fact the data in question is of more global nature and not really
tied to an IPL device, so separating it is rather logical.
This commit introduces a new structure to hold firmware relevant
IPL parameters set by QEMU. The data is stored at location 204 (dec)
and can contain up to 7 32-bit words. This area is available to
programming in the z/Architecture Principles of Operation and
can thus safely be used by the firmware until the IPL has completed.
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
[thuth: fixed "4 + 8 * n" comment]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Moved:
memcmp from bootmap.h to libc.h (renamed from _memcmp)
strlen from sclp.c to libc.h (renamed from _strlen)
Added C standard functions:
isdigit
Added non C-standard function:
uitoa
atoui
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
ECKD DASDs have different IPL structures for CDL and LDL
formats. The current Ipl1 and Ipl2 structs follow the CDL
format, so we prepend "EckdCdl" to them. Boot info for LDL
has been moved to a new struct: EckdLdlIpl1.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Acked-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add new cylinder/head/sector struct. Use it to calculate
eckd block numbers instead of a BootMapPointer (which used
eckd chs anyway).
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Some ECKD bootmap code was using structs designed for SCSI.
Even though this works, it confuses readability. Add a new
BootMapTable struct to assist with readability in bootmap
entry code. Also:
- replace ScsiMbr in ECKD code with appropriate structs
- fix read_block messages to reflect BootMapTable
- fixup ipl_scsi to use BootMapTable (referred to as Program Table)
- defined value for maximum table entries
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This is skiboot 5.9 (commit e0ee24c2). It brings improved POWER9
support among many other things. Built from submodule.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The main changes are:
- able to handle more devices with specified bootindex;
- implements flatten device tree rendering, for both QEMU and guest kernel.
The full list is:
> boot: use a temporary bootdev-buf
> boot: do not concatenate bootdev
> libvirtio: Mark struct virtio_scsi_req_cmd as packed
> fdt: Implement "fdt-fetch" method for client interface
> rtas: Store RTAS address and entry in the device tree
> board-qemu: Fix slof-build-id length
> fdt: Pass the resulting device tree to QEMU
> fdt: Fix version and add a word for FDT header size
> tree: Rework set-chosen-cpu and store /chosen ihandle and phandle
> node: Add some documentation
> Revert various SLOF-to-QEMU private hypercalls
> Use input-device and output-device
> netboot: Create bootp-response when bootp is used
> libnet/ipv6: assign times_asked value directly
> usb-xhci: Reset ERSTSZ together with ERSTBA
> virtio-net: rework the driver to support multiple open
> board-qemu: add private hcall to inform host on "phandle" update
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The QEMU ELF loader does not zero the bss segment.
This resulted in several bugs, e.g. see
commit 5d739a4787 (s390-ccw.img: Fix sporadic errors with ccw boot image - initialize css)
commit 6a40fa2669d3 (s390-ccw.img: Initialize next_idx)
commit 8775d91a0f (pc-bios/s390-ccw: Fix problem with invalid virtio-scsi LUN when rebooting)
Let's fix this once and forever by letting the BIOS zero the bss itself.
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20171122142627.73170-3-borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The owner of qemu.org has delegated authority to modify DNS records to
the QEMU Project. This has allowed us to use the domain name without
worries about IP address changes or technical issues disrupting service.
The issues described in commit 8593898109
("Use qemu-project.org domain name") have therefore been mitigated.
This patch switches back to consistently using qemu.org instead of
qemu-project.org in documentation, version.rc, and the Windows installer
script.
The git submodules and SeaBIOS still use qemu-project.org for the time
being. This will be fixed in the QEMU 2.12 release cycle.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20171121120435.28728-2-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Contains the following commit:
- pc-bios/s390-ccw: Fix problem with invalid virtio-scsi LUN when rebooting
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
When rebooting a guest that has a virtio-scsi disk, the s390-ccw
bios sometimes bails out with an error message like this:
! SCSI cannot report LUNs: STATUS=02 RSPN=70 KEY=05 CODE=25 QLFR=00, sure !
Enabling the scsi_req* tracing in QEMU shows that the ccw bios is
trying to execute the REPORT LUNS SCSI command with a LUN != 0, and
this causes the SCSI command to fail.
Looks like we neither clear the BSS of the s390-ccw bios during reboot,
nor do we explicitly set the default_scsi_device.lun value to 0, so
this variable can contain random values from the OS after the reboot.
By setting this variable explicitly to 0, the problem is fixed and
the reboots always succeed.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1514352
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1510942228-22822-1-git-send-email-thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Update our pre-release seabios snapshot to the final release.
git shortlog
============
Gerd Hoffmann (1):
sercon: Disable ScreenAndDebug in case both serial console and serial debug are active
Kevin O'Connor (2):
timer: Avoid integer overflows in usec and nsec calculations
docs: Note v1.11.0 release
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
includes
7618c0aefe ("s390-ccw: print carriage return with new lines")
a8fbbf1db7 ("s390: set DHCP client architecure id for netboot")
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The sclp console in the s390 bios writes raw data,
leading console emulators (such as virsh console) to
treat a new line ('\n') as just a new line instead
of as a Unix line feed. Because of this, output
appears in a "stair case" pattern.
Let's print \r\n on every occurrence of a new line
in the string passed to write to amend this issue.
This is in sync with the guest Linux code in
drivers/s390/char/sclp_vt220.c which also does a line feed
conversion in the console part of the driver.
This fixes the s390-ccw and s390-netboot output like
$ virsh start test --console
Domain test started
Connected to domain test
Escape character is ^]
Network boot starting...
Using MAC address: 02:01:02:03:04:05
Requesting information via DHCP: 010
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Message-Id: <1509120893-28054-1-git-send-email-walling@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Thomas Huth