mirror of https://gitee.com/openkylin/qemu.git
471 lines
13 KiB
C
471 lines
13 KiB
C
/*
|
|
* TI OMAP on-chip I2C controller. Only "new I2C" mode supported.
|
|
*
|
|
* Copyright (C) 2007 Andrzej Zaborowski <balrog@zabor.org>
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License along
|
|
* with this program; if not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
#include "hw.h"
|
|
#include "i2c.h"
|
|
#include "omap.h"
|
|
|
|
struct omap_i2c_s {
|
|
qemu_irq irq;
|
|
qemu_irq drq[2];
|
|
i2c_bus *bus;
|
|
|
|
uint8_t revision;
|
|
uint8_t mask;
|
|
uint16_t stat;
|
|
uint16_t dma;
|
|
uint16_t count;
|
|
int count_cur;
|
|
uint32_t fifo;
|
|
int rxlen;
|
|
int txlen;
|
|
uint16_t control;
|
|
uint16_t addr[2];
|
|
uint8_t divider;
|
|
uint8_t times[2];
|
|
uint16_t test;
|
|
};
|
|
|
|
#define OMAP2_INTR_REV 0x34
|
|
#define OMAP2_GC_REV 0x34
|
|
|
|
static void omap_i2c_interrupts_update(struct omap_i2c_s *s)
|
|
{
|
|
qemu_set_irq(s->irq, s->stat & s->mask);
|
|
if ((s->dma >> 15) & 1) /* RDMA_EN */
|
|
qemu_set_irq(s->drq[0], (s->stat >> 3) & 1); /* RRDY */
|
|
if ((s->dma >> 7) & 1) /* XDMA_EN */
|
|
qemu_set_irq(s->drq[1], (s->stat >> 4) & 1); /* XRDY */
|
|
}
|
|
|
|
static void omap_i2c_fifo_run(struct omap_i2c_s *s)
|
|
{
|
|
int ack = 1;
|
|
|
|
if (!i2c_bus_busy(s->bus))
|
|
return;
|
|
|
|
if ((s->control >> 2) & 1) { /* RM */
|
|
if ((s->control >> 1) & 1) { /* STP */
|
|
i2c_end_transfer(s->bus);
|
|
s->control &= ~(1 << 1); /* STP */
|
|
s->count_cur = s->count;
|
|
s->txlen = 0;
|
|
} else if ((s->control >> 9) & 1) { /* TRX */
|
|
while (ack && s->txlen)
|
|
ack = (i2c_send(s->bus,
|
|
(s->fifo >> ((-- s->txlen) << 3)) &
|
|
0xff) >= 0);
|
|
s->stat |= 1 << 4; /* XRDY */
|
|
} else {
|
|
while (s->rxlen < 4)
|
|
s->fifo |= i2c_recv(s->bus) << ((s->rxlen ++) << 3);
|
|
s->stat |= 1 << 3; /* RRDY */
|
|
}
|
|
} else {
|
|
if ((s->control >> 9) & 1) { /* TRX */
|
|
while (ack && s->count_cur && s->txlen) {
|
|
ack = (i2c_send(s->bus,
|
|
(s->fifo >> ((-- s->txlen) << 3)) &
|
|
0xff) >= 0);
|
|
s->count_cur --;
|
|
}
|
|
if (ack && s->count_cur)
|
|
s->stat |= 1 << 4; /* XRDY */
|
|
else
|
|
s->stat &= ~(1 << 4); /* XRDY */
|
|
if (!s->count_cur) {
|
|
s->stat |= 1 << 2; /* ARDY */
|
|
s->control &= ~(1 << 10); /* MST */
|
|
}
|
|
} else {
|
|
while (s->count_cur && s->rxlen < 4) {
|
|
s->fifo |= i2c_recv(s->bus) << ((s->rxlen ++) << 3);
|
|
s->count_cur --;
|
|
}
|
|
if (s->rxlen)
|
|
s->stat |= 1 << 3; /* RRDY */
|
|
else
|
|
s->stat &= ~(1 << 3); /* RRDY */
|
|
}
|
|
if (!s->count_cur) {
|
|
if ((s->control >> 1) & 1) { /* STP */
|
|
i2c_end_transfer(s->bus);
|
|
s->control &= ~(1 << 1); /* STP */
|
|
s->count_cur = s->count;
|
|
s->txlen = 0;
|
|
} else {
|
|
s->stat |= 1 << 2; /* ARDY */
|
|
s->control &= ~(1 << 10); /* MST */
|
|
}
|
|
}
|
|
}
|
|
|
|
s->stat |= (!ack) << 1; /* NACK */
|
|
if (!ack)
|
|
s->control &= ~(1 << 1); /* STP */
|
|
}
|
|
|
|
void omap_i2c_reset(struct omap_i2c_s *s)
|
|
{
|
|
s->mask = 0;
|
|
s->stat = 0;
|
|
s->dma = 0;
|
|
s->count = 0;
|
|
s->count_cur = 0;
|
|
s->fifo = 0;
|
|
s->rxlen = 0;
|
|
s->txlen = 0;
|
|
s->control = 0;
|
|
s->addr[0] = 0;
|
|
s->addr[1] = 0;
|
|
s->divider = 0;
|
|
s->times[0] = 0;
|
|
s->times[1] = 0;
|
|
s->test = 0;
|
|
}
|
|
|
|
static uint32_t omap_i2c_read(void *opaque, target_phys_addr_t addr)
|
|
{
|
|
struct omap_i2c_s *s = (struct omap_i2c_s *) opaque;
|
|
int offset = addr & OMAP_MPUI_REG_MASK;
|
|
uint16_t ret;
|
|
|
|
switch (offset) {
|
|
case 0x00: /* I2C_REV */
|
|
return s->revision; /* REV */
|
|
|
|
case 0x04: /* I2C_IE */
|
|
return s->mask;
|
|
|
|
case 0x08: /* I2C_STAT */
|
|
return s->stat | (i2c_bus_busy(s->bus) << 12);
|
|
|
|
case 0x0c: /* I2C_IV */
|
|
if (s->revision >= OMAP2_INTR_REV)
|
|
break;
|
|
ret = ffs(s->stat & s->mask);
|
|
if (ret)
|
|
s->stat ^= 1 << (ret - 1);
|
|
omap_i2c_interrupts_update(s);
|
|
return ret;
|
|
|
|
case 0x10: /* I2C_SYSS */
|
|
return (s->control >> 15) & 1; /* I2C_EN */
|
|
|
|
case 0x14: /* I2C_BUF */
|
|
return s->dma;
|
|
|
|
case 0x18: /* I2C_CNT */
|
|
return s->count_cur; /* DCOUNT */
|
|
|
|
case 0x1c: /* I2C_DATA */
|
|
ret = 0;
|
|
if (s->control & (1 << 14)) { /* BE */
|
|
ret |= ((s->fifo >> 0) & 0xff) << 8;
|
|
ret |= ((s->fifo >> 8) & 0xff) << 0;
|
|
} else {
|
|
ret |= ((s->fifo >> 8) & 0xff) << 8;
|
|
ret |= ((s->fifo >> 0) & 0xff) << 0;
|
|
}
|
|
if (s->rxlen == 1) {
|
|
s->stat |= 1 << 15; /* SBD */
|
|
s->rxlen = 0;
|
|
} else if (s->rxlen > 1) {
|
|
if (s->rxlen > 2)
|
|
s->fifo >>= 16;
|
|
s->rxlen -= 2;
|
|
} else {
|
|
/* XXX: remote access (qualifier) error - what's that? */
|
|
}
|
|
if (!s->rxlen) {
|
|
s->stat &= ~(1 << 3); /* RRDY */
|
|
if (((s->control >> 10) & 1) && /* MST */
|
|
((~s->control >> 9) & 1)) { /* TRX */
|
|
s->stat |= 1 << 2; /* ARDY */
|
|
s->control &= ~(1 << 10); /* MST */
|
|
}
|
|
}
|
|
s->stat &= ~(1 << 11); /* ROVR */
|
|
omap_i2c_fifo_run(s);
|
|
omap_i2c_interrupts_update(s);
|
|
return ret;
|
|
|
|
case 0x20: /* I2C_SYSC */
|
|
return 0;
|
|
|
|
case 0x24: /* I2C_CON */
|
|
return s->control;
|
|
|
|
case 0x28: /* I2C_OA */
|
|
return s->addr[0];
|
|
|
|
case 0x2c: /* I2C_SA */
|
|
return s->addr[1];
|
|
|
|
case 0x30: /* I2C_PSC */
|
|
return s->divider;
|
|
|
|
case 0x34: /* I2C_SCLL */
|
|
return s->times[0];
|
|
|
|
case 0x38: /* I2C_SCLH */
|
|
return s->times[1];
|
|
|
|
case 0x3c: /* I2C_SYSTEST */
|
|
if (s->test & (1 << 15)) { /* ST_EN */
|
|
s->test ^= 0xa;
|
|
return s->test;
|
|
} else
|
|
return s->test & ~0x300f;
|
|
}
|
|
|
|
OMAP_BAD_REG(addr);
|
|
return 0;
|
|
}
|
|
|
|
static void omap_i2c_write(void *opaque, target_phys_addr_t addr,
|
|
uint32_t value)
|
|
{
|
|
struct omap_i2c_s *s = (struct omap_i2c_s *) opaque;
|
|
int offset = addr & OMAP_MPUI_REG_MASK;
|
|
int nack;
|
|
|
|
switch (offset) {
|
|
case 0x00: /* I2C_REV */
|
|
case 0x0c: /* I2C_IV */
|
|
case 0x10: /* I2C_SYSS */
|
|
OMAP_RO_REG(addr);
|
|
return;
|
|
|
|
case 0x04: /* I2C_IE */
|
|
s->mask = value & (s->revision < OMAP2_GC_REV ? 0x1f : 0x3f);
|
|
break;
|
|
|
|
case 0x08: /* I2C_STAT */
|
|
if (s->revision < OMAP2_INTR_REV) {
|
|
OMAP_RO_REG(addr);
|
|
return;
|
|
}
|
|
|
|
/* RRDY and XRDY are reset by hardware. (in all versions???) */
|
|
s->stat &= ~(value & 0x27);
|
|
omap_i2c_interrupts_update(s);
|
|
break;
|
|
|
|
case 0x14: /* I2C_BUF */
|
|
s->dma = value & 0x8080;
|
|
if (value & (1 << 15)) /* RDMA_EN */
|
|
s->mask &= ~(1 << 3); /* RRDY_IE */
|
|
if (value & (1 << 7)) /* XDMA_EN */
|
|
s->mask &= ~(1 << 4); /* XRDY_IE */
|
|
break;
|
|
|
|
case 0x18: /* I2C_CNT */
|
|
s->count = value; /* DCOUNT */
|
|
break;
|
|
|
|
case 0x1c: /* I2C_DATA */
|
|
if (s->txlen > 2) {
|
|
/* XXX: remote access (qualifier) error - what's that? */
|
|
break;
|
|
}
|
|
s->fifo <<= 16;
|
|
s->txlen += 2;
|
|
if (s->control & (1 << 14)) { /* BE */
|
|
s->fifo |= ((value >> 8) & 0xff) << 8;
|
|
s->fifo |= ((value >> 0) & 0xff) << 0;
|
|
} else {
|
|
s->fifo |= ((value >> 0) & 0xff) << 8;
|
|
s->fifo |= ((value >> 8) & 0xff) << 0;
|
|
}
|
|
s->stat &= ~(1 << 10); /* XUDF */
|
|
if (s->txlen > 2)
|
|
s->stat &= ~(1 << 4); /* XRDY */
|
|
omap_i2c_fifo_run(s);
|
|
omap_i2c_interrupts_update(s);
|
|
break;
|
|
|
|
case 0x20: /* I2C_SYSC */
|
|
if (s->revision < OMAP2_INTR_REV) {
|
|
OMAP_BAD_REG(addr);
|
|
return;
|
|
}
|
|
|
|
if (value & 2)
|
|
omap_i2c_reset(s);
|
|
break;
|
|
|
|
case 0x24: /* I2C_CON */
|
|
s->control = value & 0xcf87;
|
|
if (~value & (1 << 15)) { /* I2C_EN */
|
|
if (s->revision < OMAP2_INTR_REV)
|
|
omap_i2c_reset(s);
|
|
break;
|
|
}
|
|
if ((value & (1 << 15)) && !(value & (1 << 10))) { /* MST */
|
|
fprintf(stderr, "%s: I^2C slave mode not supported\n",
|
|
__FUNCTION__);
|
|
break;
|
|
}
|
|
if ((value & (1 << 15)) && value & (1 << 8)) { /* XA */
|
|
fprintf(stderr, "%s: 10-bit addressing mode not supported\n",
|
|
__FUNCTION__);
|
|
break;
|
|
}
|
|
if ((value & (1 << 15)) && value & (1 << 0)) { /* STT */
|
|
nack = !!i2c_start_transfer(s->bus, s->addr[1], /* SA */
|
|
(~value >> 9) & 1); /* TRX */
|
|
s->stat |= nack << 1; /* NACK */
|
|
s->control &= ~(1 << 0); /* STT */
|
|
s->fifo = 0;
|
|
if (nack)
|
|
s->control &= ~(1 << 1); /* STP */
|
|
else {
|
|
s->count_cur = s->count;
|
|
omap_i2c_fifo_run(s);
|
|
}
|
|
omap_i2c_interrupts_update(s);
|
|
}
|
|
break;
|
|
|
|
case 0x28: /* I2C_OA */
|
|
s->addr[0] = value & 0x3ff;
|
|
break;
|
|
|
|
case 0x2c: /* I2C_SA */
|
|
s->addr[1] = value & 0x3ff;
|
|
break;
|
|
|
|
case 0x30: /* I2C_PSC */
|
|
s->divider = value;
|
|
break;
|
|
|
|
case 0x34: /* I2C_SCLL */
|
|
s->times[0] = value;
|
|
break;
|
|
|
|
case 0x38: /* I2C_SCLH */
|
|
s->times[1] = value;
|
|
break;
|
|
|
|
case 0x3c: /* I2C_SYSTEST */
|
|
s->test = value & 0xf80f;
|
|
if (value & (1 << 11)) /* SBB */
|
|
if (s->revision >= OMAP2_INTR_REV) {
|
|
s->stat |= 0x3f;
|
|
omap_i2c_interrupts_update(s);
|
|
}
|
|
if (value & (1 << 15)) /* ST_EN */
|
|
fprintf(stderr, "%s: System Test not supported\n", __FUNCTION__);
|
|
break;
|
|
|
|
default:
|
|
OMAP_BAD_REG(addr);
|
|
return;
|
|
}
|
|
}
|
|
|
|
static void omap_i2c_writeb(void *opaque, target_phys_addr_t addr,
|
|
uint32_t value)
|
|
{
|
|
struct omap_i2c_s *s = (struct omap_i2c_s *) opaque;
|
|
int offset = addr & OMAP_MPUI_REG_MASK;
|
|
|
|
switch (offset) {
|
|
case 0x1c: /* I2C_DATA */
|
|
if (s->txlen > 2) {
|
|
/* XXX: remote access (qualifier) error - what's that? */
|
|
break;
|
|
}
|
|
s->fifo <<= 8;
|
|
s->txlen += 1;
|
|
s->fifo |= value & 0xff;
|
|
s->stat &= ~(1 << 10); /* XUDF */
|
|
if (s->txlen > 2)
|
|
s->stat &= ~(1 << 4); /* XRDY */
|
|
omap_i2c_fifo_run(s);
|
|
omap_i2c_interrupts_update(s);
|
|
break;
|
|
|
|
default:
|
|
OMAP_BAD_REG(addr);
|
|
return;
|
|
}
|
|
}
|
|
|
|
static CPUReadMemoryFunc * const omap_i2c_readfn[] = {
|
|
omap_badwidth_read16,
|
|
omap_i2c_read,
|
|
omap_badwidth_read16,
|
|
};
|
|
|
|
static CPUWriteMemoryFunc * const omap_i2c_writefn[] = {
|
|
omap_i2c_writeb, /* Only the last fifo write can be 8 bit. */
|
|
omap_i2c_write,
|
|
omap_badwidth_write16,
|
|
};
|
|
|
|
struct omap_i2c_s *omap_i2c_init(target_phys_addr_t base,
|
|
qemu_irq irq, qemu_irq *dma, omap_clk clk)
|
|
{
|
|
int iomemtype;
|
|
struct omap_i2c_s *s = (struct omap_i2c_s *)
|
|
qemu_mallocz(sizeof(struct omap_i2c_s));
|
|
|
|
/* TODO: set a value greater or equal to real hardware */
|
|
s->revision = 0x11;
|
|
s->irq = irq;
|
|
s->drq[0] = dma[0];
|
|
s->drq[1] = dma[1];
|
|
s->bus = i2c_init_bus(NULL, "i2c");
|
|
omap_i2c_reset(s);
|
|
|
|
iomemtype = cpu_register_io_memory(omap_i2c_readfn,
|
|
omap_i2c_writefn, s, DEVICE_NATIVE_ENDIAN);
|
|
cpu_register_physical_memory(base, 0x800, iomemtype);
|
|
|
|
return s;
|
|
}
|
|
|
|
struct omap_i2c_s *omap2_i2c_init(struct omap_target_agent_s *ta,
|
|
qemu_irq irq, qemu_irq *dma, omap_clk fclk, omap_clk iclk)
|
|
{
|
|
int iomemtype;
|
|
struct omap_i2c_s *s = (struct omap_i2c_s *)
|
|
qemu_mallocz(sizeof(struct omap_i2c_s));
|
|
|
|
s->revision = 0x34;
|
|
s->irq = irq;
|
|
s->drq[0] = dma[0];
|
|
s->drq[1] = dma[1];
|
|
s->bus = i2c_init_bus(NULL, "i2c");
|
|
omap_i2c_reset(s);
|
|
|
|
iomemtype = l4_register_io_memory(omap_i2c_readfn,
|
|
omap_i2c_writefn, s);
|
|
omap_l4_attach(ta, 0, iomemtype);
|
|
|
|
return s;
|
|
}
|
|
|
|
i2c_bus *omap_i2c_bus(struct omap_i2c_s *s)
|
|
{
|
|
return s->bus;
|
|
}
|