308 lines
6.0 KiB
Plaintext
308 lines
6.0 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
|
|
/*
|
|
* Copyright (C) Arrow Electronics 2019 - All Rights Reserved
|
|
* Author: Botond Kardos <botond.kardos@arroweurope.com>
|
|
*
|
|
* Copyright (C) Linaro Ltd 2019 - All Rights Reserved
|
|
* Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "stm32mp157.dtsi"
|
|
#include "stm32mp15-pinctrl.dtsi"
|
|
#include "stm32mp15xxac-pinctrl.dtsi"
|
|
#include <dt-bindings/clock/stm32mp1-clksrc.h>
|
|
#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
|
|
|
|
/ {
|
|
model = "Arrow Electronics STM32MP157A Avenger96 board";
|
|
compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
|
|
|
|
aliases {
|
|
mmc0 = &sdmmc1;
|
|
serial0 = &uart4;
|
|
serial1 = &uart7;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
memory@c0000000 {
|
|
device_type = "memory";
|
|
reg = <0xc0000000 0x40000000>;
|
|
};
|
|
};
|
|
|
|
&i2c4 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c4_pins_a>;
|
|
i2c-scl-rising-time-ns = <185>;
|
|
i2c-scl-falling-time-ns = <20>;
|
|
status = "okay";
|
|
|
|
pmic: stpmic@33 {
|
|
compatible = "st,stpmic1";
|
|
reg = <0x33>;
|
|
interrupts-extended = <&exti_pwr 55 IRQ_TYPE_EDGE_FALLING>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
status = "okay";
|
|
|
|
st,main-control-register = <0x04>;
|
|
st,vin-control-register = <0xc0>;
|
|
st,usb-control-register = <0x30>;
|
|
|
|
regulators {
|
|
compatible = "st,stpmic1-regulators";
|
|
ldo1-supply = <&v3v3>;
|
|
ldo2-supply = <&v3v3>;
|
|
ldo3-supply = <&vdd_ddr>;
|
|
ldo5-supply = <&v3v3>;
|
|
ldo6-supply = <&v3v3>;
|
|
pwr_sw1-supply = <&bst_out>;
|
|
pwr_sw2-supply = <&bst_out>;
|
|
|
|
vddcore: buck1 {
|
|
regulator-name = "vddcore";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-always-on;
|
|
regulator-initial-mode = <0>;
|
|
regulator-over-current-protection;
|
|
};
|
|
|
|
vdd_ddr: buck2 {
|
|
regulator-name = "vdd_ddr";
|
|
regulator-min-microvolt = <1350000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-always-on;
|
|
regulator-initial-mode = <0>;
|
|
regulator-over-current-protection;
|
|
};
|
|
|
|
vdd: buck3 {
|
|
regulator-name = "vdd";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
st,mask-reset;
|
|
regulator-initial-mode = <0>;
|
|
regulator-over-current-protection;
|
|
};
|
|
|
|
v3v3: buck4 {
|
|
regulator-name = "v3v3";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
regulator-over-current-protection;
|
|
regulator-initial-mode = <0>;
|
|
};
|
|
|
|
vdda: ldo1 {
|
|
regulator-name = "vdda";
|
|
regulator-min-microvolt = <2900000>;
|
|
regulator-max-microvolt = <2900000>;
|
|
};
|
|
|
|
v2v8: ldo2 {
|
|
regulator-name = "v2v8";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
};
|
|
|
|
vtt_ddr: ldo3 {
|
|
regulator-name = "vtt_ddr";
|
|
regulator-min-microvolt = <500000>;
|
|
regulator-max-microvolt = <750000>;
|
|
regulator-always-on;
|
|
regulator-over-current-protection;
|
|
};
|
|
|
|
vdd_usb: ldo4 {
|
|
regulator-name = "vdd_usb";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
vdd_sd: ldo5 {
|
|
regulator-name = "vdd_sd";
|
|
regulator-min-microvolt = <2900000>;
|
|
regulator-max-microvolt = <2900000>;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
v1v8: ldo6 {
|
|
regulator-name = "v1v8";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
};
|
|
|
|
vref_ddr: vref_ddr {
|
|
regulator-name = "vref_ddr";
|
|
regulator-always-on;
|
|
regulator-over-current-protection;
|
|
};
|
|
|
|
bst_out: boost {
|
|
regulator-name = "bst_out";
|
|
};
|
|
|
|
vbus_otg: pwr_sw1 {
|
|
regulator-name = "vbus_otg";
|
|
};
|
|
|
|
vbus_sw: pwr_sw2 {
|
|
regulator-name = "vbus_sw";
|
|
regulator-active-discharge = <1>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&iwdg2 {
|
|
timeout-sec = <32>;
|
|
status = "okay";
|
|
secure-status = "okay";
|
|
};
|
|
|
|
&pwr_regulators {
|
|
vdd-supply = <&vdd>;
|
|
vdd_3v3_usbfs-supply = <&vdd_usb>;
|
|
};
|
|
|
|
&rcc {
|
|
secure-status = "disabled";
|
|
st,clksrc = <
|
|
CLK_MPU_PLL1P
|
|
CLK_AXI_PLL2P
|
|
CLK_MCU_PLL3P
|
|
CLK_PLL12_HSE
|
|
CLK_PLL3_HSE
|
|
CLK_PLL4_HSE
|
|
CLK_RTC_LSE
|
|
CLK_MCO1_DISABLED
|
|
CLK_MCO2_DISABLED
|
|
>;
|
|
|
|
st,clkdiv = <
|
|
1 /*MPU*/
|
|
0 /*AXI*/
|
|
0 /*MCU*/
|
|
1 /*APB1*/
|
|
1 /*APB2*/
|
|
1 /*APB3*/
|
|
1 /*APB4*/
|
|
2 /*APB5*/
|
|
23 /*RTC*/
|
|
0 /*MCO1*/
|
|
0 /*MCO2*/
|
|
>;
|
|
|
|
st,pkcs = <
|
|
CLK_CKPER_HSE
|
|
CLK_FMC_ACLK
|
|
CLK_QSPI_ACLK
|
|
CLK_ETH_DISABLED
|
|
CLK_SDMMC12_PLL4P
|
|
CLK_DSI_DSIPLL
|
|
CLK_STGEN_HSE
|
|
CLK_USBPHY_HSE
|
|
CLK_SPI2S1_PLL3Q
|
|
CLK_SPI2S23_PLL3Q
|
|
CLK_SPI45_HSI
|
|
CLK_SPI6_HSI
|
|
CLK_I2C46_HSI
|
|
CLK_SDMMC3_PLL4P
|
|
CLK_USBO_USBPHY
|
|
CLK_ADC_CKPER
|
|
CLK_CEC_LSE
|
|
CLK_I2C12_HSI
|
|
CLK_I2C35_HSI
|
|
CLK_UART1_HSI
|
|
CLK_UART24_HSI
|
|
CLK_UART35_HSI
|
|
CLK_UART6_HSI
|
|
CLK_UART78_HSI
|
|
CLK_SPDIF_PLL4P
|
|
CLK_FDCAN_PLL4R
|
|
CLK_SAI1_PLL3Q
|
|
CLK_SAI2_PLL3Q
|
|
CLK_SAI3_PLL3Q
|
|
CLK_SAI4_PLL3Q
|
|
CLK_RNG1_LSI
|
|
CLK_RNG2_LSI
|
|
CLK_LPTIM1_PCLK1
|
|
CLK_LPTIM23_PCLK3
|
|
CLK_LPTIM45_LSE
|
|
>;
|
|
|
|
/* VCO = 1300.0 MHz => P = 650 (CPU) */
|
|
pll1: st,pll@0 {
|
|
compatible = "st,stm32mp1-pll";
|
|
reg = <0>;
|
|
cfg = <2 80 0 0 0 PQR(1,0,0)>;
|
|
frac = <0x800>;
|
|
};
|
|
|
|
/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
|
|
pll2: st,pll@1 {
|
|
compatible = "st,stm32mp1-pll";
|
|
reg = <1>;
|
|
cfg = <2 65 1 0 0 PQR(1,1,1)>;
|
|
frac = <0x1400>;
|
|
};
|
|
|
|
/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
|
|
pll3: st,pll@2 {
|
|
compatible = "st,stm32mp1-pll";
|
|
reg = <2>;
|
|
cfg = <1 33 1 16 36 PQR(1,1,1)>;
|
|
frac = <0x1a04>;
|
|
};
|
|
|
|
/* VCO = 480.0 MHz => P = 120, Q = 40, R = 96 */
|
|
pll4: st,pll@3 {
|
|
compatible = "st,stm32mp1-pll";
|
|
reg = <3>;
|
|
cfg = <1 39 3 11 4 PQR(1,1,1)>;
|
|
};
|
|
};
|
|
|
|
&rng1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&rtc {
|
|
status = "okay";
|
|
};
|
|
|
|
&sdmmc1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
|
|
st,sig-dir;
|
|
st,neg-edge;
|
|
st,use-ckin;
|
|
bus-width = <4>;
|
|
vmmc-supply = <&vdd_sd>;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart4 {
|
|
/* On Low speed expansion header */
|
|
label = "LS-UART1";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart4_pins_b>;
|
|
status = "okay";
|
|
};
|
|
|
|
&uart7 {
|
|
/* On Low speed expansion header */
|
|
label = "LS-UART0";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&uart7_pins_a>;
|
|
status = "okay";
|
|
};
|