p71924506
/
linux_old1
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
linux_old1/net/mpls/af_mpls.c

1250 lines
29 KiB
C
Raw Normal View History

mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
#include <linux/types.h>
#include <linux/skbuff.h>
#include <linux/socket.h>
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
#include <linux/sysctl.h>
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
#include <linux/net.h>
#include <linux/module.h>
#include <linux/if_arp.h>
#include <linux/ipv6.h>
#include <linux/mpls.h>
mpls: using vzalloc requires including vmalloc.h Fixes this build error: net/mpls/af_mpls.c: In function 'resize_platform_label_table': net/mpls/af_mpls.c:767:4: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration] labels = vzalloc(size); ^ Fixes: 7720c01f3f59 ("mpls: Add a sysctl to control the size of the mpls label table") Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-05 10:37:05 +08:00
#include <linux/vmalloc.h>
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
#include <net/ip.h>
#include <net/dst.h>
#include <net/sock.h>
#include <net/arp.h>
#include <net/ip_fib.h>
#include <net/netevent.h>
#include <net/netns/generic.h>
af_mpls: fix undefined reference to ip6_route_output Undefined reference to ip6_route_output and ip_route_output was reported with CONFIG_INET=n and CONFIG_IPV6=n. This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of ip6_route_output. And wraps affected code under IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6). Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 04:34:54 +08:00
#if IS_ENABLED(CONFIG_IPV6)
#include <net/ipv6.h>
#include <net/addrconf.h>
#endif
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
#include "internal.h"
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
#define LABEL_NOT_SPECIFIED (1<<20)
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
#define MAX_NEW_LABELS 2
/* This maximum ha length copied from the definition of struct neighbour */
#define MAX_VIA_ALEN (ALIGN(MAX_ADDR_LEN, sizeof(unsigned long)))
struct mpls_route { /* next hop label forwarding entry */
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
struct net_device __rcu *rt_dev;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
struct rcu_head rt_rcu;
u32 rt_label[MAX_NEW_LABELS];
u8 rt_protocol; /* routing protocol that set this entry */
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
u8 rt_labels;
u8 rt_via_alen;
u8 rt_via_table;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
u8 rt_via[0];
};
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
static int zero = 0;
static int label_limit = (1 << 20) - 1;
mpls: Multicast route table change notifications Unlike IPv4 this code notifies on all cases where mpls routes are added or removed and it never automatically removes routes. Avoiding both the userspace confusion that is caused by omitting route updates and the possibility of a flood of netlink traffic when an interface goes doew. For now reserved labels are handled automatically and userspace is not notified. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:14:31 +08:00
static void rtmsg_lfib(int event, u32 label, struct mpls_route *rt,
struct nlmsghdr *nlh, struct net *net, u32 portid,
unsigned int nlm_flags);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
static struct mpls_route *mpls_route_input_rcu(struct net *net, unsigned index)
{
struct mpls_route *rt = NULL;
if (index < net->mpls.platform_labels) {
struct mpls_route __rcu **platform_label =
rcu_dereference(net->mpls.platform_label);
rt = rcu_dereference(platform_label[index]);
}
return rt;
}
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
static inline struct mpls_dev *mpls_dev_get(const struct net_device *dev)
{
return rcu_dereference_rtnl(dev->mpls_ptr);
}
mpls: export mpls functions for use by mpls iptunnels Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-21 16:43:52 +08:00
bool mpls_output_possible(const struct net_device *dev)
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
{
return dev && (dev->flags & IFF_UP) && netif_carrier_ok(dev);
}
mpls: export mpls functions for use by mpls iptunnels Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-21 16:43:52 +08:00
EXPORT_SYMBOL_GPL(mpls_output_possible);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
static unsigned int mpls_rt_header_size(const struct mpls_route *rt)
{
/* The size of the layer 2.5 labels to be added for this route */
return rt->rt_labels * sizeof(struct mpls_shim_hdr);
}
mpls: export mpls functions for use by mpls iptunnels Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-21 16:43:52 +08:00
unsigned int mpls_dev_mtu(const struct net_device *dev)
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
{
/* The amount of data the layer 2 frame can hold */
return dev->mtu;
}
mpls: export mpls functions for use by mpls iptunnels Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-21 16:43:52 +08:00
EXPORT_SYMBOL_GPL(mpls_dev_mtu);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
mpls: export mpls functions for use by mpls iptunnels Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-21 16:43:52 +08:00
bool mpls_pkt_too_big(const struct sk_buff *skb, unsigned int mtu)
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
{
if (skb->len <= mtu)
return false;
if (skb_is_gso(skb) && skb_gso_network_seglen(skb) <= mtu)
return false;
return true;
}
mpls: export mpls functions for use by mpls iptunnels Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-21 16:43:52 +08:00
EXPORT_SYMBOL_GPL(mpls_pkt_too_big);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
static bool mpls_egress(struct mpls_route *rt, struct sk_buff *skb,
struct mpls_entry_decoded dec)
{
/* RFC4385 and RFC5586 encode other packets in mpls such that
* they don't conflict with the ip version number, making
* decoding by examining the ip version correct in everything
* except for the strangest cases.
*
* The strange cases if we choose to support them will require
* manual configuration.
*/
mpls: In mpls_egress verify the packet length. Reobert Shearman noticed that mpls_egress is failing to verify that the bytes to be examined are in fact present in the packet before mpls_egress reads those bytes. As suggested by David Miller reduce this to a single pskb_may_pull call so that we don't do unnecessary work in the fast path. Reported-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-13 07:22:59 +08:00
struct iphdr *hdr4;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
bool success = true;
mpls: In mpls_egress verify the packet length. Reobert Shearman noticed that mpls_egress is failing to verify that the bytes to be examined are in fact present in the packet before mpls_egress reads those bytes. As suggested by David Miller reduce this to a single pskb_may_pull call so that we don't do unnecessary work in the fast path. Reported-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-13 07:22:59 +08:00
/* The IPv4 code below accesses through the IPv4 header
* checksum, which is 12 bytes into the packet.
* The IPv6 code below accesses through the IPv6 hop limit
* which is 8 bytes into the packet.
*
* For all supported cases there should always be at least 12
* bytes of packet data present. The IPv4 header is 20 bytes
* without options and the IPv6 header is always 40 bytes
* long.
*/
if (!pskb_may_pull(skb, 12))
return false;
/* Use ip_hdr to find the ip protocol version */
hdr4 = ip_hdr(skb);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
if (hdr4->version == 4) {
skb->protocol = htons(ETH_P_IP);
csum_replace2(&hdr4->check,
htons(hdr4->ttl << 8),
htons(dec.ttl << 8));
hdr4->ttl = dec.ttl;
}
else if (hdr4->version == 6) {
struct ipv6hdr *hdr6 = ipv6_hdr(skb);
skb->protocol = htons(ETH_P_IPV6);
hdr6->hop_limit = dec.ttl;
}
else
/* version 0 and version 1 are used by pseudo wires */
success = false;
return success;
}
static int mpls_forward(struct sk_buff *skb, struct net_device *dev,
struct packet_type *pt, struct net_device *orig_dev)
{
struct net *net = dev_net(dev);
struct mpls_shim_hdr *hdr;
struct mpls_route *rt;
struct mpls_entry_decoded dec;
struct net_device *out_dev;
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
struct mpls_dev *mdev;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
unsigned int hh_len;
unsigned int new_header_size;
unsigned int mtu;
int err;
/* Careful this entire function runs inside of an rcu critical section */
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
mdev = mpls_dev_get(dev);
mpls: Per-device enabling of packet input An MPLS network is a single trust domain where the edges must be in control of what labels make their way into the core. The simplest way of ensuring this is for the edge device to always impose the labels, and not allow forward labeled traffic from untrusted neighbours. This is achieved by allowing a per-device configuration of whether MPLS traffic input from that interface should be processed or not. To be secure by default, the default state is changed to MPLS being disabled on all interfaces unless explicitly enabled and no global option is provided to change the default. Whilst this differs from other protocols (e.g. IPv6), network operators are used to explicitly enabling MPLS forwarding on interfaces, and with the number of links to the MPLS core typically fairly low this doesn't present too much of a burden on operators. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:38 +08:00
if (!mdev || !mdev->input_enabled)
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
goto drop;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
if (skb->pkt_type != PACKET_HOST)
goto drop;
if ((skb = skb_share_check(skb, GFP_ATOMIC)) == NULL)
goto drop;
if (!pskb_may_pull(skb, sizeof(*hdr)))
goto drop;
/* Read and decode the label */
hdr = mpls_hdr(skb);
dec = mpls_entry_decode(hdr);
/* Pop the label */
skb_pull(skb, sizeof(*hdr));
skb_reset_network_header(skb);
skb_orphan(skb);
rt = mpls_route_input_rcu(net, dec.label);
if (!rt)
goto drop;
/* Find the output device */
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
out_dev = rcu_dereference(rt->rt_dev);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
if (!mpls_output_possible(out_dev))
goto drop;
if (skb_warn_if_lro(skb))
goto drop;
skb_forward_csum(skb);
/* Verify ttl is valid */
mpls: Correct the ttl decrement. According to RFC3032 section 2.4.2 packets with an outgoing ttl of 0 MUST NOT be forwarded. According to section 2.4.1 an outgoing TTL of 0 comes from an incomming TTL <= 1. Therefore any packets that is received with a ttl <= 1 should not have it's ttl decremented and forwarded. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:23:23 +08:00
if (dec.ttl <= 1)
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
goto drop;
dec.ttl -= 1;
/* Verify the destination can hold the packet */
new_header_size = mpls_rt_header_size(rt);
mtu = mpls_dev_mtu(out_dev);
if (mpls_pkt_too_big(skb, mtu - new_header_size))
goto drop;
hh_len = LL_RESERVED_SPACE(out_dev);
if (!out_dev->header_ops)
hh_len = 0;
/* Ensure there is enough space for the headers in the skb */
if (skb_cow(skb, hh_len + new_header_size))
goto drop;
skb->dev = out_dev;
skb->protocol = htons(ETH_P_MPLS_UC);
if (unlikely(!new_header_size && dec.bos)) {
/* Penultimate hop popping */
if (!mpls_egress(rt, skb, dec))
goto drop;
} else {
bool bos;
int i;
skb_push(skb, new_header_size);
skb_reset_network_header(skb);
/* Push the new labels */
hdr = mpls_hdr(skb);
bos = dec.bos;
for (i = rt->rt_labels - 1; i >= 0; i--) {
hdr[i] = mpls_entry_encode(rt->rt_label[i], dec.ttl, 0, bos);
bos = false;
}
}
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
err = neigh_xmit(rt->rt_via_table, out_dev, rt->rt_via, skb);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
if (err)
net_dbg_ratelimited("%s: packet transmission failed: %d\n",
__func__, err);
return 0;
drop:
kfree_skb(skb);
return NET_RX_DROP;
}
static struct packet_type mpls_packet_type __read_mostly = {
.type = cpu_to_be16(ETH_P_MPLS_UC),
.func = mpls_forward,
};
mpls: rtm_mpls_policy[] can be static Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-05 05:33:54 +08:00
static const struct nla_policy rtm_mpls_policy[RTA_MAX+1] = {
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
[RTA_DST] = { .type = NLA_U32 },
[RTA_OIF] = { .type = NLA_U32 },
};
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
struct mpls_route_config {
u32 rc_protocol;
u32 rc_ifindex;
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
u16 rc_via_table;
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
u16 rc_via_alen;
u8 rc_via[MAX_VIA_ALEN];
u32 rc_label;
u32 rc_output_labels;
u32 rc_output_label[MAX_NEW_LABELS];
u32 rc_nlflags;
struct nl_info rc_nlinfo;
};
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
static struct mpls_route *mpls_rt_alloc(size_t alen)
{
struct mpls_route *rt;
mpls: Fix the kzalloc argument order in mpls_rt_alloc *Blink* I got the argument order wrong to kzalloc and the code was working properly when tested. *Blink* Fix that. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:19:41 +08:00
rt = kzalloc(sizeof(*rt) + alen, GFP_KERNEL);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
if (rt)
rt->rt_via_alen = alen;
return rt;
}
static void mpls_rt_free(struct mpls_route *rt)
{
if (rt)
kfree_rcu(rt, rt_rcu);
}
mpls: Multicast route table change notifications Unlike IPv4 this code notifies on all cases where mpls routes are added or removed and it never automatically removes routes. Avoiding both the userspace confusion that is caused by omitting route updates and the possibility of a flood of netlink traffic when an interface goes doew. For now reserved labels are handled automatically and userspace is not notified. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:14:31 +08:00
static void mpls_notify_route(struct net *net, unsigned index,
struct mpls_route *old, struct mpls_route *new,
const struct nl_info *info)
{
struct nlmsghdr *nlh = info ? info->nlh : NULL;
unsigned portid = info ? info->portid : 0;
int event = new ? RTM_NEWROUTE : RTM_DELROUTE;
struct mpls_route *rt = new ? new : old;
unsigned nlm_flags = (old && new) ? NLM_F_REPLACE : 0;
/* Ignore reserved labels for now */
mpls: Use definition for reserved label checks In multiple locations there are checks for whether the label in hand is a reserved label or not using the arbritray value of 16. Factor this out into a #define for better maintainability and for documentation. Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-04 00:50:04 +08:00
if (rt && (index >= MPLS_LABEL_FIRST_UNRESERVED))
mpls: Multicast route table change notifications Unlike IPv4 this code notifies on all cases where mpls routes are added or removed and it never automatically removes routes. Avoiding both the userspace confusion that is caused by omitting route updates and the possibility of a flood of netlink traffic when an interface goes doew. For now reserved labels are handled automatically and userspace is not notified. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:14:31 +08:00
rtmsg_lfib(event, index, rt, nlh, net, portid, nlm_flags);
}
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
static void mpls_route_update(struct net *net, unsigned index,
struct net_device *dev, struct mpls_route *new,
const struct nl_info *info)
{
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
struct mpls_route __rcu **platform_label;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
struct mpls_route *rt, *old = NULL;
ASSERT_RTNL();
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
platform_label = rtnl_dereference(net->mpls.platform_label);
rt = rtnl_dereference(platform_label[index]);
if (!dev || (rt && (rtnl_dereference(rt->rt_dev) == dev))) {
rcu_assign_pointer(platform_label[index], new);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
old = rt;
}
mpls: Multicast route table change notifications Unlike IPv4 this code notifies on all cases where mpls routes are added or removed and it never automatically removes routes. Avoiding both the userspace confusion that is caused by omitting route updates and the possibility of a flood of netlink traffic when an interface goes doew. For now reserved labels are handled automatically and userspace is not notified. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:14:31 +08:00
mpls_notify_route(net, index, old, new, info);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
/* If we removed a route free it now */
mpls_rt_free(old);
}
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
static unsigned find_free_label(struct net *net)
{
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
struct mpls_route __rcu **platform_label;
size_t platform_labels;
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
unsigned index;
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
platform_label = rtnl_dereference(net->mpls.platform_label);
platform_labels = net->mpls.platform_labels;
mpls: Use definition for reserved label checks In multiple locations there are checks for whether the label in hand is a reserved label or not using the arbritray value of 16. Factor this out into a #define for better maintainability and for documentation. Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-04 00:50:04 +08:00
for (index = MPLS_LABEL_FIRST_UNRESERVED; index < platform_labels;
index++) {
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
if (!rtnl_dereference(platform_label[index]))
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
return index;
}
return LABEL_NOT_SPECIFIED;
}
af_mpls: fix undefined reference to ip6_route_output Undefined reference to ip6_route_output and ip_route_output was reported with CONFIG_INET=n and CONFIG_IPV6=n. This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of ip6_route_output. And wraps affected code under IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6). Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 04:34:54 +08:00
#if IS_ENABLED(CONFIG_INET)
mpls: make RTA_OIF optional If user did not specify an oif, try and get it from the via address. If failed to get device, return with -ENODEV. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-22 00:16:24 +08:00
static struct net_device *inet_fib_lookup_dev(struct net *net, void *addr)
{
struct net_device *dev = NULL;
struct rtable *rt;
struct in_addr daddr;
memcpy(&daddr, addr, sizeof(struct in_addr));
rt = ip_route_output(net, daddr.s_addr, 0, 0, 0);
if (IS_ERR(rt))
goto errout;
dev = rt->dst.dev;
dev_hold(dev);
ip_rt_put(rt);
return dev;
af_mpls: fix undefined reference to ip6_route_output Undefined reference to ip6_route_output and ip_route_output was reported with CONFIG_INET=n and CONFIG_IPV6=n. This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of ip6_route_output. And wraps affected code under IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6). Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 04:34:54 +08:00
errout:
return ERR_PTR(-ENODEV);
}
#else
static struct net_device *inet_fib_lookup_dev(struct net *net, void *addr)
{
return ERR_PTR(-EAFNOSUPPORT);
mpls: make RTA_OIF optional If user did not specify an oif, try and get it from the via address. If failed to get device, return with -ENODEV. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-22 00:16:24 +08:00
}
af_mpls: fix undefined reference to ip6_route_output Undefined reference to ip6_route_output and ip_route_output was reported with CONFIG_INET=n and CONFIG_IPV6=n. This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of ip6_route_output. And wraps affected code under IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6). Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 04:34:54 +08:00
#endif
mpls: make RTA_OIF optional If user did not specify an oif, try and get it from the via address. If failed to get device, return with -ENODEV. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-22 00:16:24 +08:00
af_mpls: fix undefined reference to ip6_route_output Undefined reference to ip6_route_output and ip_route_output was reported with CONFIG_INET=n and CONFIG_IPV6=n. This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of ip6_route_output. And wraps affected code under IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6). Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 04:34:54 +08:00
#if IS_ENABLED(CONFIG_IPV6)
mpls: make RTA_OIF optional If user did not specify an oif, try and get it from the via address. If failed to get device, return with -ENODEV. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-22 00:16:24 +08:00
static struct net_device *inet6_fib_lookup_dev(struct net *net, void *addr)
{
struct net_device *dev = NULL;
struct dst_entry *dst;
struct flowi6 fl6;
af_mpls: fix undefined reference to ip6_route_output Undefined reference to ip6_route_output and ip_route_output was reported with CONFIG_INET=n and CONFIG_IPV6=n. This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of ip6_route_output. And wraps affected code under IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6). Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 04:34:54 +08:00
int err;
if (!ipv6_stub)
return ERR_PTR(-EAFNOSUPPORT);
mpls: make RTA_OIF optional If user did not specify an oif, try and get it from the via address. If failed to get device, return with -ENODEV. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-22 00:16:24 +08:00
memset(&fl6, 0, sizeof(fl6));
memcpy(&fl6.daddr, addr, sizeof(struct in6_addr));
af_mpls: fix undefined reference to ip6_route_output Undefined reference to ip6_route_output and ip_route_output was reported with CONFIG_INET=n and CONFIG_IPV6=n. This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of ip6_route_output. And wraps affected code under IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6). Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 04:34:54 +08:00
err = ipv6_stub->ipv6_dst_lookup(net, NULL, &dst, &fl6);
if (err)
mpls: make RTA_OIF optional If user did not specify an oif, try and get it from the via address. If failed to get device, return with -ENODEV. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-22 00:16:24 +08:00
goto errout;
dev = dst->dev;
dev_hold(dev);
dst_release(dst);
return dev;
af_mpls: fix undefined reference to ip6_route_output Undefined reference to ip6_route_output and ip_route_output was reported with CONFIG_INET=n and CONFIG_IPV6=n. This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of ip6_route_output. And wraps affected code under IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6). Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 04:34:54 +08:00
errout:
return ERR_PTR(err);
mpls: make RTA_OIF optional If user did not specify an oif, try and get it from the via address. If failed to get device, return with -ENODEV. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-22 00:16:24 +08:00
}
af_mpls: fix undefined reference to ip6_route_output Undefined reference to ip6_route_output and ip_route_output was reported with CONFIG_INET=n and CONFIG_IPV6=n. This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of ip6_route_output. And wraps affected code under IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6). Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 04:34:54 +08:00
#else
static struct net_device *inet6_fib_lookup_dev(struct net *net, void *addr)
{
return ERR_PTR(-EAFNOSUPPORT);
}
#endif
mpls: make RTA_OIF optional If user did not specify an oif, try and get it from the via address. If failed to get device, return with -ENODEV. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-22 00:16:24 +08:00
static struct net_device *find_outdev(struct net *net,
struct mpls_route_config *cfg)
{
struct net_device *dev = NULL;
if (!cfg->rc_ifindex) {
switch (cfg->rc_via_table) {
case NEIGH_ARP_TABLE:
dev = inet_fib_lookup_dev(net, cfg->rc_via);
break;
case NEIGH_ND_TABLE:
dev = inet6_fib_lookup_dev(net, cfg->rc_via);
break;
case NEIGH_LINK_TABLE:
break;
}
} else {
dev = dev_get_by_index(net, cfg->rc_ifindex);
}
return dev;
}
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
static int mpls_route_add(struct mpls_route_config *cfg)
{
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
struct mpls_route __rcu **platform_label;
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
struct net *net = cfg->rc_nlinfo.nl_net;
struct net_device *dev = NULL;
struct mpls_route *rt, *old;
unsigned index;
int i;
int err = -EINVAL;
index = cfg->rc_label;
/* If a label was not specified during insert pick one */
if ((index == LABEL_NOT_SPECIFIED) &&
(cfg->rc_nlflags & NLM_F_CREATE)) {
index = find_free_label(net);
}
mpls: Use definition for reserved label checks In multiple locations there are checks for whether the label in hand is a reserved label or not using the arbritray value of 16. Factor this out into a #define for better maintainability and for documentation. Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-04 00:50:04 +08:00
/* Reserved labels may not be set */
if (index < MPLS_LABEL_FIRST_UNRESERVED)
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
goto errout;
/* The full 20 bit range may not be supported. */
if (index >= net->mpls.platform_labels)
goto errout;
/* Ensure only a supported number of labels are present */
if (cfg->rc_output_labels > MAX_NEW_LABELS)
goto errout;
mpls: make RTA_OIF optional If user did not specify an oif, try and get it from the via address. If failed to get device, return with -ENODEV. Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-22 00:16:24 +08:00
dev = find_outdev(net, cfg);
af_mpls: fix undefined reference to ip6_route_output Undefined reference to ip6_route_output and ip_route_output was reported with CONFIG_INET=n and CONFIG_IPV6=n. This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of ip6_route_output. And wraps affected code under IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6). Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 04:34:54 +08:00
if (IS_ERR(dev)) {
err = PTR_ERR(dev);
dev = NULL;
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
goto errout;
af_mpls: fix undefined reference to ip6_route_output Undefined reference to ip6_route_output and ip_route_output was reported with CONFIG_INET=n and CONFIG_IPV6=n. This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of ip6_route_output. And wraps affected code under IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6). Reported-by: kbuild test robot <fengguang.wu@intel.com> Reported-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-31 04:34:54 +08:00
}
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
/* Ensure this is a supported device */
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
err = -EINVAL;
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
if (!mpls_dev_get(dev))
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
goto errout;
err = -EINVAL;
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
if ((cfg->rc_via_table == NEIGH_LINK_TABLE) &&
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
(dev->addr_len != cfg->rc_via_alen))
goto errout;
/* Append makes no sense with mpls */
mpls: Better error code for unsupported option. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:22:40 +08:00
err = -EOPNOTSUPP;
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
if (cfg->rc_nlflags & NLM_F_APPEND)
goto errout;
err = -EEXIST;
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
platform_label = rtnl_dereference(net->mpls.platform_label);
old = rtnl_dereference(platform_label[index]);
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
if ((cfg->rc_nlflags & NLM_F_EXCL) && old)
goto errout;
err = -EEXIST;
if (!(cfg->rc_nlflags & NLM_F_REPLACE) && old)
goto errout;
err = -ENOENT;
if (!(cfg->rc_nlflags & NLM_F_CREATE) && !old)
goto errout;
err = -ENOMEM;
rt = mpls_rt_alloc(cfg->rc_via_alen);
if (!rt)
goto errout;
rt->rt_labels = cfg->rc_output_labels;
for (i = 0; i < rt->rt_labels; i++)
rt->rt_label[i] = cfg->rc_output_label[i];
rt->rt_protocol = cfg->rc_protocol;
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
RCU_INIT_POINTER(rt->rt_dev, dev);
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
rt->rt_via_table = cfg->rc_via_table;
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
memcpy(rt->rt_via, cfg->rc_via, cfg->rc_via_alen);
mpls_route_update(net, index, NULL, rt, &cfg->rc_nlinfo);
dev_put(dev);
return 0;
errout:
if (dev)
dev_put(dev);
return err;
}
static int mpls_route_del(struct mpls_route_config *cfg)
{
struct net *net = cfg->rc_nlinfo.nl_net;
unsigned index;
int err = -EINVAL;
index = cfg->rc_label;
mpls: Use definition for reserved label checks In multiple locations there are checks for whether the label in hand is a reserved label or not using the arbritray value of 16. Factor this out into a #define for better maintainability and for documentation. Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-04 00:50:04 +08:00
/* Reserved labels may not be removed */
if (index < MPLS_LABEL_FIRST_UNRESERVED)
mpls: Basic support for adding and removing routes mpls_route_add and mpls_route_del implement the basic logic for adding and removing Next Hop Label Forwarding Entries from the MPLS input label map. The addition and subtraction is done in a way that is consistent with how the existing routing table in Linux are maintained. Thus all of the work to deal with NLM_F_APPEND, NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE. Cases that are not clearly defined such as changing the interpretation of the mpls reserved labels is not allowed. Because it seems like the right thing to do adding an MPLS route without specifying an input label and allowing the kernel to pick a free label table entry is supported. The implementation is currently less than optimal but that can be changed. As I don't have anything else to test with only ethernet and the loopback device are the only two device types currently supported for forwarding MPLS over. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:12:40 +08:00
goto errout;
/* The full 20 bit range may not be supported */
if (index >= net->mpls.platform_labels)
goto errout;
mpls_route_update(net, index, NULL, NULL, &cfg->rc_nlinfo);
err = 0;
errout:
return err;
}
mpls: Per-device enabling of packet input An MPLS network is a single trust domain where the edges must be in control of what labels make their way into the core. The simplest way of ensuring this is for the edge device to always impose the labels, and not allow forward labeled traffic from untrusted neighbours. This is achieved by allowing a per-device configuration of whether MPLS traffic input from that interface should be processed or not. To be secure by default, the default state is changed to MPLS being disabled on all interfaces unless explicitly enabled and no global option is provided to change the default. Whilst this differs from other protocols (e.g. IPv6), network operators are used to explicitly enabling MPLS forwarding on interfaces, and with the number of links to the MPLS core typically fairly low this doesn't present too much of a burden on operators. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:38 +08:00
#define MPLS_PERDEV_SYSCTL_OFFSET(field) \
(&((struct mpls_dev *)0)->field)
static const struct ctl_table mpls_dev_table[] = {
{
.procname = "input",
.maxlen = sizeof(int),
.mode = 0644,
.proc_handler = proc_dointvec,
.data = MPLS_PERDEV_SYSCTL_OFFSET(input_enabled),
},
{ }
};
static int mpls_dev_sysctl_register(struct net_device *dev,
struct mpls_dev *mdev)
{
char path[sizeof("net/mpls/conf/") + IFNAMSIZ];
struct ctl_table *table;
int i;
table = kmemdup(&mpls_dev_table, sizeof(mpls_dev_table), GFP_KERNEL);
if (!table)
goto out;
/* Table data contains only offsets relative to the base of
* the mdev at this point, so make them absolute.
*/
for (i = 0; i < ARRAY_SIZE(mpls_dev_table); i++)
table[i].data = (char *)mdev + (uintptr_t)table[i].data;
snprintf(path, sizeof(path), "net/mpls/conf/%s", dev->name);
mdev->sysctl = register_net_sysctl(dev_net(dev), path, table);
if (!mdev->sysctl)
goto free;
return 0;
free:
kfree(table);
out:
return -ENOBUFS;
}
static void mpls_dev_sysctl_unregister(struct mpls_dev *mdev)
{
struct ctl_table *table;
table = mdev->sysctl->ctl_table_arg;
unregister_net_sysctl_table(mdev->sysctl);
kfree(table);
}
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
static struct mpls_dev *mpls_add_dev(struct net_device *dev)
{
struct mpls_dev *mdev;
int err = -ENOMEM;
ASSERT_RTNL();
mdev = kzalloc(sizeof(*mdev), GFP_KERNEL);
if (!mdev)
return ERR_PTR(err);
mpls: Per-device enabling of packet input An MPLS network is a single trust domain where the edges must be in control of what labels make their way into the core. The simplest way of ensuring this is for the edge device to always impose the labels, and not allow forward labeled traffic from untrusted neighbours. This is achieved by allowing a per-device configuration of whether MPLS traffic input from that interface should be processed or not. To be secure by default, the default state is changed to MPLS being disabled on all interfaces unless explicitly enabled and no global option is provided to change the default. Whilst this differs from other protocols (e.g. IPv6), network operators are used to explicitly enabling MPLS forwarding on interfaces, and with the number of links to the MPLS core typically fairly low this doesn't present too much of a burden on operators. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:38 +08:00
err = mpls_dev_sysctl_register(dev, mdev);
if (err)
goto free;
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
rcu_assign_pointer(dev->mpls_ptr, mdev);
return mdev;
mpls: Per-device enabling of packet input An MPLS network is a single trust domain where the edges must be in control of what labels make their way into the core. The simplest way of ensuring this is for the edge device to always impose the labels, and not allow forward labeled traffic from untrusted neighbours. This is achieved by allowing a per-device configuration of whether MPLS traffic input from that interface should be processed or not. To be secure by default, the default state is changed to MPLS being disabled on all interfaces unless explicitly enabled and no global option is provided to change the default. Whilst this differs from other protocols (e.g. IPv6), network operators are used to explicitly enabling MPLS forwarding on interfaces, and with the number of links to the MPLS core typically fairly low this doesn't present too much of a burden on operators. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:38 +08:00
free:
kfree(mdev);
return ERR_PTR(err);
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
}
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
static void mpls_ifdown(struct net_device *dev)
{
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
struct mpls_route __rcu **platform_label;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
struct net *net = dev_net(dev);
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
struct mpls_dev *mdev;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
unsigned index;
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
platform_label = rtnl_dereference(net->mpls.platform_label);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
for (index = 0; index < net->mpls.platform_labels; index++) {
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
struct mpls_route *rt = rtnl_dereference(platform_label[index]);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
if (!rt)
continue;
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
if (rtnl_dereference(rt->rt_dev) != dev)
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
continue;
rt->rt_dev = NULL;
}
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
mdev = mpls_dev_get(dev);
if (!mdev)
return;
mpls: Per-device enabling of packet input An MPLS network is a single trust domain where the edges must be in control of what labels make their way into the core. The simplest way of ensuring this is for the edge device to always impose the labels, and not allow forward labeled traffic from untrusted neighbours. This is achieved by allowing a per-device configuration of whether MPLS traffic input from that interface should be processed or not. To be secure by default, the default state is changed to MPLS being disabled on all interfaces unless explicitly enabled and no global option is provided to change the default. Whilst this differs from other protocols (e.g. IPv6), network operators are used to explicitly enabling MPLS forwarding on interfaces, and with the number of links to the MPLS core typically fairly low this doesn't present too much of a burden on operators. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:38 +08:00
mpls_dev_sysctl_unregister(mdev);
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
RCU_INIT_POINTER(dev->mpls_ptr, NULL);
mpls: fix possible use after free of device The mpls device is used in an RCU read context without a lock being held. As the memory is freed without waiting for the RCU grace period to elapse, the freed memory could still be in use. Address this by using kfree_rcu to free the memory for the mpls device after the RCU grace period has elapsed. Fixes: 03c57747a702 ("mpls: Per-device MPLS state") Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-06 01:54:45 +08:00
kfree_rcu(mdev, rcu);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
}
static int mpls_dev_notify(struct notifier_block *this, unsigned long event,
void *ptr)
{
struct net_device *dev = netdev_notifier_info_to_dev(ptr);
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
struct mpls_dev *mdev;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
switch(event) {
mpls: Per-device MPLS state Add per-device MPLS state to supported interfaces. Use the presence of this state in mpls_route_add to determine that this is a supported interface. Use the presence of mpls_dev to drop packets that arrived on an unsupported interface - previously they were allowed through. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:37 +08:00
case NETDEV_REGISTER:
/* For now just support ethernet devices */
if ((dev->type == ARPHRD_ETHER) ||
(dev->type == ARPHRD_LOOPBACK)) {
mdev = mpls_add_dev(dev);
if (IS_ERR(mdev))
return notifier_from_errno(PTR_ERR(mdev));
}
break;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
case NETDEV_UNREGISTER:
mpls_ifdown(dev);
break;
mpls: handle device renames for per-device sysctls If a device is renamed and the original name is subsequently reused for a new device, the following warning is generated: sysctl duplicate entry: /net/mpls/conf/veth0//input CPU: 3 PID: 1379 Comm: ip Not tainted 4.1.0-rc4+ #20 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014 0000000000000000 0000000000000000 ffffffff81566aaf 0000000000000000 ffffffff81236279 ffff88002f7d7f00 0000000000000000 ffff88000db336d8 ffff88000db33698 0000000000000005 ffff88002e046000 ffff8800168c9280 Call Trace: [<ffffffff81566aaf>] ? dump_stack+0x40/0x50 [<ffffffff81236279>] ? __register_sysctl_table+0x289/0x5a0 [<ffffffffa051a24f>] ? mpls_dev_notify+0x1ff/0x300 [mpls_router] [<ffffffff8108db7f>] ? notifier_call_chain+0x4f/0x70 [<ffffffff81470e72>] ? register_netdevice+0x2b2/0x480 [<ffffffffa0524748>] ? veth_newlink+0x178/0x2d3 [veth] [<ffffffff8147f84c>] ? rtnl_newlink+0x73c/0x8e0 [<ffffffff8147f27a>] ? rtnl_newlink+0x16a/0x8e0 [<ffffffff81459ff2>] ? __kmalloc_reserve.isra.30+0x32/0x90 [<ffffffff8147ccfd>] ? rtnetlink_rcv_msg+0x8d/0x250 [<ffffffff8145b027>] ? __alloc_skb+0x47/0x1f0 [<ffffffff8149badb>] ? __netlink_lookup+0xab/0xe0 [<ffffffff8147cc70>] ? rtnetlink_rcv+0x30/0x30 [<ffffffff8149e7a0>] ? netlink_rcv_skb+0xb0/0xd0 [<ffffffff8147cc64>] ? rtnetlink_rcv+0x24/0x30 [<ffffffff8149df17>] ? netlink_unicast+0x107/0x1a0 [<ffffffff8149e4be>] ? netlink_sendmsg+0x50e/0x630 [<ffffffff8145209c>] ? sock_sendmsg+0x3c/0x50 [<ffffffff81452beb>] ? ___sys_sendmsg+0x27b/0x290 [<ffffffff811bd258>] ? mem_cgroup_try_charge+0x88/0x110 [<ffffffff811bd5b6>] ? mem_cgroup_commit_charge+0x56/0xa0 [<ffffffff811d7700>] ? do_filp_open+0x30/0xa0 [<ffffffff8145336e>] ? __sys_sendmsg+0x3e/0x80 [<ffffffff8156c3f2>] ? system_call_fastpath+0x16/0x75 Fix this by unregistering the previous sysctl table (registered for the path containing the original device name) and re-registering the table for the path containing the new device name. Fixes: 37bde79979c3 ("mpls: Per-device enabling of packet input") Reported-by: Scott Feldman <sfeldma@gmail.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-12 02:58:26 +08:00
case NETDEV_CHANGENAME:
mdev = mpls_dev_get(dev);
if (mdev) {
int err;
mpls_dev_sysctl_unregister(mdev);
err = mpls_dev_sysctl_register(dev, mdev);
if (err)
return notifier_from_errno(err);
}
break;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
}
return NOTIFY_OK;
}
static struct notifier_block mpls_dev_notifier = {
.notifier_call = mpls_dev_notify,
};
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
static int nla_put_via(struct sk_buff *skb,
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
u8 table, const void *addr, int alen)
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
{
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
static const int table_to_family[NEIGH_NR_TABLES + 1] = {
AF_INET, AF_INET6, AF_DECnet, AF_PACKET,
};
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
struct nlattr *nla;
struct rtvia *via;
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
int family = AF_UNSPEC;
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
nla = nla_reserve(skb, RTA_VIA, alen + 2);
if (!nla)
return -EMSGSIZE;
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
if (table <= NEIGH_NR_TABLES)
family = table_to_family[table];
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
via = nla_data(nla);
via->rtvia_family = family;
memcpy(via->rtvia_addr, addr, alen);
return 0;
}
mpls: Functions for reading and wrinting mpls labels over netlink Reading and writing addresses in network byte order in netlink is traditional and I see no reason to change that. MPLS is interesting as effectively it has variabely length addresses (the MPLS label stack). To represent these variable length addresses in netlink I use a valid MPLS label stack (complete with stop bit). This achieves two things: a well defined existing format is used, and the data can be interpreted without looking at it's length. Not needed to look at the length to decode the variable length network representation allows existing userspace functions such as inet_ntop to be used without needed to change their prototype. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:19 +08:00
int nla_put_labels(struct sk_buff *skb, int attrtype,
u8 labels, const u32 label[])
{
struct nlattr *nla;
struct mpls_shim_hdr *nla_label;
bool bos;
int i;
nla = nla_reserve(skb, attrtype, labels*4);
if (!nla)
return -EMSGSIZE;
nla_label = nla_data(nla);
bos = true;
for (i = labels - 1; i >= 0; i--) {
nla_label[i] = mpls_entry_encode(label[i], 0, 0, bos);
bos = false;
}
return 0;
}
mpls: export mpls functions for use by mpls iptunnels Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-21 16:43:52 +08:00
EXPORT_SYMBOL_GPL(nla_put_labels);
mpls: Functions for reading and wrinting mpls labels over netlink Reading and writing addresses in network byte order in netlink is traditional and I see no reason to change that. MPLS is interesting as effectively it has variabely length addresses (the MPLS label stack). To represent these variable length addresses in netlink I use a valid MPLS label stack (complete with stop bit). This achieves two things: a well defined existing format is used, and the data can be interpreted without looking at it's length. Not needed to look at the length to decode the variable length network representation allows existing userspace functions such as inet_ntop to be used without needed to change their prototype. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:19 +08:00
int nla_get_labels(const struct nlattr *nla,
u32 max_labels, u32 *labels, u32 label[])
{
unsigned len = nla_len(nla);
unsigned nla_labels;
struct mpls_shim_hdr *nla_label;
bool bos;
int i;
/* len needs to be an even multiple of 4 (the label size) */
if (len & 3)
return -EINVAL;
/* Limit the number of new labels allowed */
nla_labels = len/4;
if (nla_labels > max_labels)
return -EINVAL;
nla_label = nla_data(nla);
bos = true;
for (i = nla_labels - 1; i >= 0; i--, bos = false) {
struct mpls_entry_decoded dec;
dec = mpls_entry_decode(nla_label + i);
/* Ensure the bottom of stack flag is properly set
* and ttl and tc are both clear.
*/
if ((dec.bos != bos) || dec.ttl || dec.tc)
return -EINVAL;
mpls: Prevent use of implicit NULL label as outgoing label The reserved implicit-NULL label isn't allowed to appear in the label stack for packets, so make it an error for the control plane to specify it as an outgoing label. Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:39 +08:00
switch (dec.label) {
mpls: Change reserved label names to be consistent with netbsd Since these are now visible to userspace it is nice to be consistent with BSD (sys/netmpls/mpls.h in netBSD). Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-07 23:08:51 +08:00
case MPLS_LABEL_IMPLNULL:
mpls: Prevent use of implicit NULL label as outgoing label The reserved implicit-NULL label isn't allowed to appear in the label stack for packets, so make it an error for the control plane to specify it as an outgoing label. Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:39 +08:00
/* RFC3032: This is a label that an LSR may
* assign and distribute, but which never
* actually appears in the encapsulation.
*/
return -EINVAL;
}
mpls: Functions for reading and wrinting mpls labels over netlink Reading and writing addresses in network byte order in netlink is traditional and I see no reason to change that. MPLS is interesting as effectively it has variabely length addresses (the MPLS label stack). To represent these variable length addresses in netlink I use a valid MPLS label stack (complete with stop bit). This achieves two things: a well defined existing format is used, and the data can be interpreted without looking at it's length. Not needed to look at the length to decode the variable length network representation allows existing userspace functions such as inet_ntop to be used without needed to change their prototype. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:19 +08:00
label[i] = dec.label;
}
*labels = nla_labels;
return 0;
}
mpls: export mpls functions for use by mpls iptunnels Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-21 16:43:52 +08:00
EXPORT_SYMBOL_GPL(nla_get_labels);
mpls: Functions for reading and wrinting mpls labels over netlink Reading and writing addresses in network byte order in netlink is traditional and I see no reason to change that. MPLS is interesting as effectively it has variabely length addresses (the MPLS label stack). To represent these variable length addresses in netlink I use a valid MPLS label stack (complete with stop bit). This achieves two things: a well defined existing format is used, and the data can be interpreted without looking at it's length. Not needed to look at the length to decode the variable length network representation allows existing userspace functions such as inet_ntop to be used without needed to change their prototype. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:19 +08:00
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
static int rtm_to_route_config(struct sk_buff *skb, struct nlmsghdr *nlh,
struct mpls_route_config *cfg)
{
struct rtmsg *rtm;
struct nlattr *tb[RTA_MAX+1];
int index;
int err;
err = nlmsg_parse(nlh, sizeof(*rtm), tb, RTA_MAX, rtm_mpls_policy);
if (err < 0)
goto errout;
err = -EINVAL;
rtm = nlmsg_data(nlh);
memset(cfg, 0, sizeof(*cfg));
if (rtm->rtm_family != AF_MPLS)
goto errout;
if (rtm->rtm_dst_len != 20)
goto errout;
if (rtm->rtm_src_len != 0)
goto errout;
if (rtm->rtm_tos != 0)
goto errout;
if (rtm->rtm_table != RT_TABLE_MAIN)
goto errout;
/* Any value is acceptable for rtm_protocol */
/* As mpls uses destination specific addresses
* (or source specific address in the case of multicast)
* all addresses have universal scope.
*/
if (rtm->rtm_scope != RT_SCOPE_UNIVERSE)
goto errout;
if (rtm->rtm_type != RTN_UNICAST)
goto errout;
if (rtm->rtm_flags != 0)
goto errout;
cfg->rc_label = LABEL_NOT_SPECIFIED;
cfg->rc_protocol = rtm->rtm_protocol;
cfg->rc_nlflags = nlh->nlmsg_flags;
cfg->rc_nlinfo.portid = NETLINK_CB(skb).portid;
cfg->rc_nlinfo.nlh = nlh;
cfg->rc_nlinfo.nl_net = sock_net(skb->sk);
for (index = 0; index <= RTA_MAX; index++) {
struct nlattr *nla = tb[index];
if (!nla)
continue;
switch(index) {
case RTA_OIF:
cfg->rc_ifindex = nla_get_u32(nla);
break;
case RTA_NEWDST:
if (nla_get_labels(nla, MAX_NEW_LABELS,
&cfg->rc_output_labels,
cfg->rc_output_label))
goto errout;
break;
case RTA_DST:
{
u32 label_count;
if (nla_get_labels(nla, 1, &label_count,
&cfg->rc_label))
goto errout;
mpls: Use definition for reserved label checks In multiple locations there are checks for whether the label in hand is a reserved label or not using the arbritray value of 16. Factor this out into a #define for better maintainability and for documentation. Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-04 00:50:04 +08:00
/* Reserved labels may not be set */
if (cfg->rc_label < MPLS_LABEL_FIRST_UNRESERVED)
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
goto errout;
break;
}
case RTA_VIA:
{
struct rtvia *via = nla_data(nla);
mpls: Properly validate RTA_VIA payload length If the nla length is less than 2 then the nla data could be accessed beyond the accessible bounds. So ensure that the nla is big enough to at least read the via_family before doing so. Replace magic value of 2. Fixes: 03c0566542f4 ("mpls: Basic support for adding and removing routes") Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-06 18:47:00 +08:00
if (nla_len(nla) < offsetof(struct rtvia, rtvia_addr))
goto errout;
cfg->rc_via_alen = nla_len(nla) -
offsetof(struct rtvia, rtvia_addr);
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
if (cfg->rc_via_alen > MAX_VIA_ALEN)
goto errout;
/* Validate the address family */
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
switch(via->rtvia_family) {
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
case AF_PACKET:
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
cfg->rc_via_table = NEIGH_LINK_TABLE;
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
break;
case AF_INET:
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
cfg->rc_via_table = NEIGH_ARP_TABLE;
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
if (cfg->rc_via_alen != 4)
goto errout;
break;
case AF_INET6:
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
cfg->rc_via_table = NEIGH_ND_TABLE;
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
if (cfg->rc_via_alen != 16)
goto errout;
break;
default:
/* Unsupported address family */
goto errout;
}
memcpy(cfg->rc_via, via->rtvia_addr, cfg->rc_via_alen);
break;
}
default:
/* Unsupported attribute */
goto errout;
}
}
err = 0;
errout:
return err;
}
static int mpls_rtm_delroute(struct sk_buff *skb, struct nlmsghdr *nlh)
{
struct mpls_route_config cfg;
int err;
err = rtm_to_route_config(skb, nlh, &cfg);
if (err < 0)
return err;
return mpls_route_del(&cfg);
}
static int mpls_rtm_newroute(struct sk_buff *skb, struct nlmsghdr *nlh)
{
struct mpls_route_config cfg;
int err;
err = rtm_to_route_config(skb, nlh, &cfg);
if (err < 0)
return err;
return mpls_route_add(&cfg);
}
static int mpls_dump_route(struct sk_buff *skb, u32 portid, u32 seq, int event,
u32 label, struct mpls_route *rt, int flags)
{
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
struct net_device *dev;
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
struct nlmsghdr *nlh;
struct rtmsg *rtm;
nlh = nlmsg_put(skb, portid, seq, event, sizeof(*rtm), flags);
if (nlh == NULL)
return -EMSGSIZE;
rtm = nlmsg_data(nlh);
rtm->rtm_family = AF_MPLS;
rtm->rtm_dst_len = 20;
rtm->rtm_src_len = 0;
rtm->rtm_tos = 0;
rtm->rtm_table = RT_TABLE_MAIN;
rtm->rtm_protocol = rt->rt_protocol;
rtm->rtm_scope = RT_SCOPE_UNIVERSE;
rtm->rtm_type = RTN_UNICAST;
rtm->rtm_flags = 0;
if (rt->rt_labels &&
nla_put_labels(skb, RTA_NEWDST, rt->rt_labels, rt->rt_label))
goto nla_put_failure;
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
if (nla_put_via(skb, rt->rt_via_table, rt->rt_via, rt->rt_via_alen))
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
goto nla_put_failure;
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
dev = rtnl_dereference(rt->rt_dev);
if (dev && nla_put_u32(skb, RTA_OIF, dev->ifindex))
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
goto nla_put_failure;
if (nla_put_labels(skb, RTA_DST, 1, &label))
goto nla_put_failure;
nlmsg_end(skb, nlh);
return 0;
nla_put_failure:
nlmsg_cancel(skb, nlh);
return -EMSGSIZE;
}
static int mpls_dump_routes(struct sk_buff *skb, struct netlink_callback *cb)
{
struct net *net = sock_net(skb->sk);
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
struct mpls_route __rcu **platform_label;
size_t platform_labels;
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
unsigned int index;
ASSERT_RTNL();
index = cb->args[0];
mpls: Use definition for reserved label checks In multiple locations there are checks for whether the label in hand is a reserved label or not using the arbritray value of 16. Factor this out into a #define for better maintainability and for documentation. Signed-off-by: Robert Shearman <rshearma@brocade.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-04 00:50:04 +08:00
if (index < MPLS_LABEL_FIRST_UNRESERVED)
index = MPLS_LABEL_FIRST_UNRESERVED;
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
platform_label = rtnl_dereference(net->mpls.platform_label);
platform_labels = net->mpls.platform_labels;
for (; index < platform_labels; index++) {
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
struct mpls_route *rt;
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
rt = rtnl_dereference(platform_label[index]);
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
if (!rt)
continue;
if (mpls_dump_route(skb, NETLINK_CB(cb->skb).portid,
cb->nlh->nlmsg_seq, RTM_NEWROUTE,
index, rt, NLM_F_MULTI) < 0)
break;
}
cb->args[0] = index;
return skb->len;
}
mpls: Multicast route table change notifications Unlike IPv4 this code notifies on all cases where mpls routes are added or removed and it never automatically removes routes. Avoiding both the userspace confusion that is caused by omitting route updates and the possibility of a flood of netlink traffic when an interface goes doew. For now reserved labels are handled automatically and userspace is not notified. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:14:31 +08:00
static inline size_t lfib_nlmsg_size(struct mpls_route *rt)
{
size_t payload =
NLMSG_ALIGN(sizeof(struct rtmsg))
+ nla_total_size(2 + rt->rt_via_alen) /* RTA_VIA */
+ nla_total_size(4); /* RTA_DST */
if (rt->rt_labels) /* RTA_NEWDST */
payload += nla_total_size(rt->rt_labels * 4);
if (rt->rt_dev) /* RTA_OIF */
payload += nla_total_size(4);
return payload;
}
static void rtmsg_lfib(int event, u32 label, struct mpls_route *rt,
struct nlmsghdr *nlh, struct net *net, u32 portid,
unsigned int nlm_flags)
{
struct sk_buff *skb;
u32 seq = nlh ? nlh->nlmsg_seq : 0;
int err = -ENOBUFS;
skb = nlmsg_new(lfib_nlmsg_size(rt), GFP_KERNEL);
if (skb == NULL)
goto errout;
err = mpls_dump_route(skb, portid, seq, event, label, rt, nlm_flags);
if (err < 0) {
/* -EMSGSIZE implies BUG in lfib_nlmsg_size */
WARN_ON(err == -EMSGSIZE);
kfree_skb(skb);
goto errout;
}
rtnl_notify(skb, net, portid, RTNLGRP_MPLS_ROUTE, nlh, GFP_KERNEL);
return;
errout:
if (err < 0)
rtnl_set_sk_err(net, RTNLGRP_MPLS_ROUTE, err);
}
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
static int resize_platform_label_table(struct net *net, size_t limit)
{
size_t size = sizeof(struct mpls_route *) * limit;
size_t old_limit;
size_t cp_size;
struct mpls_route __rcu **labels = NULL, **old;
struct mpls_route *rt0 = NULL, *rt2 = NULL;
unsigned index;
if (size) {
labels = kzalloc(size, GFP_KERNEL | __GFP_NOWARN | __GFP_NORETRY);
if (!labels)
labels = vzalloc(size);
if (!labels)
goto nolabels;
}
/* In case the predefined labels need to be populated */
mpls: Change reserved label names to be consistent with netbsd Since these are now visible to userspace it is nice to be consistent with BSD (sys/netmpls/mpls.h in netBSD). Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-07 23:08:51 +08:00
if (limit > MPLS_LABEL_IPV4NULL) {
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
struct net_device *lo = net->loopback_dev;
rt0 = mpls_rt_alloc(lo->addr_len);
if (!rt0)
goto nort0;
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
RCU_INIT_POINTER(rt0->rt_dev, lo);
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
rt0->rt_protocol = RTPROT_KERNEL;
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
rt0->rt_via_table = NEIGH_LINK_TABLE;
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
memcpy(rt0->rt_via, lo->dev_addr, lo->addr_len);
}
mpls: Change reserved label names to be consistent with netbsd Since these are now visible to userspace it is nice to be consistent with BSD (sys/netmpls/mpls.h in netBSD). Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-07 23:08:51 +08:00
if (limit > MPLS_LABEL_IPV6NULL) {
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
struct net_device *lo = net->loopback_dev;
rt2 = mpls_rt_alloc(lo->addr_len);
if (!rt2)
goto nort2;
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
RCU_INIT_POINTER(rt2->rt_dev, lo);
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
rt2->rt_protocol = RTPROT_KERNEL;
neigh: Use neigh table index for neigh_packet_xmit Remove a little bit of unnecessary work when transmitting a packet with neigh_packet_xmit. Use the neighbour table index not the address family as a parameter. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:25:56 +08:00
rt2->rt_via_table = NEIGH_LINK_TABLE;
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
memcpy(rt2->rt_via, lo->dev_addr, lo->addr_len);
}
rtnl_lock();
/* Remember the original table */
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
old = rtnl_dereference(net->mpls.platform_label);
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
old_limit = net->mpls.platform_labels;
/* Free any labels beyond the new table */
for (index = limit; index < old_limit; index++)
mpls_route_update(net, index, NULL, NULL, NULL);
/* Copy over the old labels */
cp_size = size;
if (old_limit < limit)
cp_size = old_limit * sizeof(struct mpls_route *);
memcpy(labels, old, cp_size);
/* If needed set the predefined labels */
mpls: Change reserved label names to be consistent with netbsd Since these are now visible to userspace it is nice to be consistent with BSD (sys/netmpls/mpls.h in netBSD). Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-07 23:08:51 +08:00
if ((old_limit <= MPLS_LABEL_IPV6NULL) &&
(limit > MPLS_LABEL_IPV6NULL)) {
RCU_INIT_POINTER(labels[MPLS_LABEL_IPV6NULL], rt2);
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
rt2 = NULL;
}
mpls: Change reserved label names to be consistent with netbsd Since these are now visible to userspace it is nice to be consistent with BSD (sys/netmpls/mpls.h in netBSD). Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-07 23:08:51 +08:00
if ((old_limit <= MPLS_LABEL_IPV4NULL) &&
(limit > MPLS_LABEL_IPV4NULL)) {
RCU_INIT_POINTER(labels[MPLS_LABEL_IPV4NULL], rt0);
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
rt0 = NULL;
}
/* Update the global pointers */
net->mpls.platform_labels = limit;
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
rcu_assign_pointer(net->mpls.platform_label, labels);
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
rtnl_unlock();
mpls_rt_free(rt2);
mpls_rt_free(rt0);
if (old) {
synchronize_rcu();
kvfree(old);
}
return 0;
nort2:
mpls_rt_free(rt0);
nort0:
kvfree(labels);
nolabels:
return -ENOMEM;
}
static int mpls_platform_labels(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct net *net = table->data;
int platform_labels = net->mpls.platform_labels;
int ret;
struct ctl_table tmp = {
.procname = table->procname,
.data = &platform_labels,
.maxlen = sizeof(int),
.mode = table->mode,
.extra1 = &zero,
.extra2 = &label_limit,
};
ret = proc_dointvec_minmax(&tmp, write, buffer, lenp, ppos);
if (write && ret == 0)
ret = resize_platform_label_table(net, platform_labels);
return ret;
}
mpls: Per-device enabling of packet input An MPLS network is a single trust domain where the edges must be in control of what labels make their way into the core. The simplest way of ensuring this is for the edge device to always impose the labels, and not allow forward labeled traffic from untrusted neighbours. This is achieved by allowing a per-device configuration of whether MPLS traffic input from that interface should be processed or not. To be secure by default, the default state is changed to MPLS being disabled on all interfaces unless explicitly enabled and no global option is provided to change the default. Whilst this differs from other protocols (e.g. IPv6), network operators are used to explicitly enabling MPLS forwarding on interfaces, and with the number of links to the MPLS core typically fairly low this doesn't present too much of a burden on operators. Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Robert Shearman <rshearma@brocade.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-04-22 18:14:38 +08:00
static const struct ctl_table mpls_table[] = {
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
{
.procname = "platform_labels",
.data = NULL,
.maxlen = sizeof(int),
.mode = 0644,
.proc_handler = mpls_platform_labels,
},
{ }
};
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
static int mpls_net_init(struct net *net)
{
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
struct ctl_table *table;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
net->mpls.platform_labels = 0;
net->mpls.platform_label = NULL;
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
table = kmemdup(mpls_table, sizeof(mpls_table), GFP_KERNEL);
if (table == NULL)
return -ENOMEM;
table[0].data = net;
net->mpls.ctl = register_net_sysctl(net, "net/mpls", table);
if (net->mpls.ctl == NULL)
return -ENOMEM;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
return 0;
}
static void mpls_net_exit(struct net *net)
{
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
struct mpls_route __rcu **platform_label;
size_t platform_labels;
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
struct ctl_table *table;
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
unsigned int index;
mpls: Add a sysctl to control the size of the mpls label table This sysctl gives two benefits. By defaulting the table size to 0 mpls even when compiled in and enabled defaults to not forwarding any packets. This prevents unpleasant surprises for users. The other benefit is that as mpls labels are allocated locally a dense table a small dense label table may be used which saves memory and is extremely simple and efficient to implement. This sysctl allows userspace to choose the restrictions on the label table size userspace applications need to cope with. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:11:20 +08:00
table = net->mpls.ctl->ctl_table_arg;
unregister_net_sysctl_table(net->mpls.ctl);
kfree(table);
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
/* An rcu grace period has passed since there was a device in
* the network namespace (and thus the last in flight packet)
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
* left this network namespace. This is because
* unregister_netdevice_many and netdev_run_todo has completed
* for each network device that was in this network namespace.
*
* As such no additional rcu synchronization is necessary when
* freeing the platform_label table.
*/
rtnl_lock();
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
platform_label = rtnl_dereference(net->mpls.platform_label);
platform_labels = net->mpls.platform_labels;
for (index = 0; index < platform_labels; index++) {
struct mpls_route *rt = rtnl_dereference(platform_label[index]);
RCU_INIT_POINTER(platform_label[index], NULL);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
mpls_rt_free(rt);
}
rtnl_unlock();
mpls: Cleanup the rcu usage in the code. Sparse was generating a lot of warnings mostly from missing annotations in the code. Add missing annotations and in a few cases tweak the code for performance by moving work before loops. This also fixes a problematic ommision of rcu_assign_pointer and rcu_dereference. Hopefully with complete rcu annotations any new rcu errors will stick out like a sore thumb. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08 06:21:56 +08:00
kvfree(platform_label);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
}
static struct pernet_operations mpls_net_ops = {
.init = mpls_net_init,
.exit = mpls_net_exit,
};
static int __init mpls_init(void)
{
int err;
BUILD_BUG_ON(sizeof(struct mpls_shim_hdr) != 4);
err = register_pernet_subsys(&mpls_net_ops);
if (err)
goto out;
err = register_netdevice_notifier(&mpls_dev_notifier);
if (err)
goto out_unregister_pernet;
dev_add_pack(&mpls_packet_type);
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
rtnl_register(PF_MPLS, RTM_NEWROUTE, mpls_rtm_newroute, NULL, NULL);
rtnl_register(PF_MPLS, RTM_DELROUTE, mpls_rtm_delroute, NULL, NULL);
rtnl_register(PF_MPLS, RTM_GETROUTE, NULL, mpls_dump_routes, NULL);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
err = 0;
out:
return err;
out_unregister_pernet:
unregister_pernet_subsys(&mpls_net_ops);
goto out;
}
module_init(mpls_init);
static void __exit mpls_exit(void)
{
mpls: Netlink commands to add, remove, and dump routes This change adds two new netlink routing attributes: RTA_VIA and RTA_NEWDST. RTA_VIA specifies the specifies the next machine to send a packet to like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it includes the address family of the address of the next machine to send a packet to. Currently the MPLS code supports addresses in AF_INET, AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac address is acquired from the neighbour table. For AF_PACKET the destination mac_address is specified in the netlink configuration. I think raw destination mac address support with the family AF_PACKET will prove useful. There is MPLS-TP which is defined to operate on machines that do not support internet packets of any flavor. Further seem to be corner cases where it can be useful. At this point I don't care much either way. RTA_NEWDST specifies the destination address to forward the packet with. MPLS typically changes it's destination address at every hop. For a swap operation RTA_NEWDST is specified with a length of one label. For a push operation RTA_NEWDST is specified with two or more labels. For a pop operation RTA_NEWDST is not specified or equivalently an emtpy RTAN_NEWDST is specified. Those new netlink attributes are used to implement handling of rt-netlink RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the MPLS label table. rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message, verify no unhandled attributes or unhandled values are present and sets up the data structures for mpls_route_add and mpls_route_del. I did my best to match up with the existing conventions with the caveats that MPLS addresses are all destination-specific-addresses, and so don't properly have a scope. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:13:56 +08:00
rtnl_unregister_all(PF_MPLS);
mpls: Basic routing support This change adds a new Kconfig option MPLS_ROUTING. The core of this change is the code to look at an mpls packet received from another machine. Look that packet up in a routing table and forward the packet on. Support of MPLS over ATM is not considered or attempted here. This implemntation follows RFC3032 and implements the MPLS shim header that can pass over essentially any network. What RFC3021 refers to as the as the Incoming Label Map (ILM) I call net->mpls.platform_label[]. What RFC3031 refers to as the Next Label Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the label fordwarding information base (lfib) might also be valid. Further the implemntation forwards packets as described in RFC3032. There is no need and given the original motivation for MPLS a strong discincentive to have a flexible label forwarding path. In essence the logic is the topmost label is read, looked up, removed, and replaced by 0 or more new lables and the sent out the specified interface to it's next hop. Quite a few optional features are not implemented here. Among them are generation of ICMP errors when the TTL is exceeded or the packet is larger than the next hop MTU (those conditions are detected and the packets are dropped instead of generating an icmp error). The traffic class field is always set to 0. The implementation focuses on IP over MPLS and does not handle egress of other kinds of protocols. Instead of implementing coordination with the neighbour table and sorting out how to input next hops in a different address family (for which there is value). I was lazy and implemented a next hop mac address instead. The code is simpler and there are flavor of MPLS such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is appropriate so a next hop by mac address would need to be implemented at some point. Two new definitions AF_MPLS and PF_MPLS are exposed to userspace. Decoding the mpls header must be done by first byeswapping a 32bit bit endian word into the local cpu endian and then bit shifting to extract the pieces. There is no C bit-field that can represent a wire format mpls header on a little endian machine as the low bits of the 20bit label wind up in the wrong half of third byte. Therefore internally everything is deal with in cpu native byte order except when writing to and reading from a packet. For management simplicity if a label is configured to forward out an interface that is down the packet is dropped early. Similarly if an network interface is removed rt_dev is updated to NULL (so no reference is preserved) and any packets for that label are dropped. Keeping the label entries in the kernel allows the kernel label table to function as the definitive source of which labels are allocated and which are not. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-04 09:10:47 +08:00
dev_remove_pack(&mpls_packet_type);
unregister_netdevice_notifier(&mpls_dev_notifier);
unregister_pernet_subsys(&mpls_net_ops);
}
module_exit(mpls_exit);
MODULE_DESCRIPTION("MultiProtocol Label Switching");
MODULE_LICENSE("GPL v2");
MODULE_ALIAS_NETPROTO(PF_MPLS);