linux_old1/drivers/spi/spi-mpc512x-psc.c

635 lines
16 KiB
C
Raw Normal View History

/*
* MPC512x PSC in SPI mode driver.
*
* Copyright (C) 2007,2008 Freescale Semiconductor Inc.
* Original port from 52xx driver:
* Hongjun Chen <hong-jun.chen@freescale.com>
*
* Fork of mpc52xx_psc_spi.c:
* Copyright (C) 2006 TOPTICA Photonics AG., Dragos Carp
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/completion.h>
#include <linux/io.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/spi/spi.h>
#include <linux/fsl_devices.h>
#include <linux/gpio.h>
#include <asm/mpc52xx_psc.h>
enum {
TYPE_MPC5121,
TYPE_MPC5125,
};
/*
* This macro abstracts the differences in the PSC register layout between
* MPC5121 (which uses a struct mpc52xx_psc) and MPC5125 (using mpc5125_psc).
*/
#define psc_addr(mps, regname) ({ \
void *__ret; \
switch(mps->type) { \
case TYPE_MPC5121: { \
struct mpc52xx_psc __iomem *psc = mps->psc; \
__ret = &psc->regname; \
}; \
break; \
case TYPE_MPC5125: { \
struct mpc5125_psc __iomem *psc = mps->psc; \
__ret = &psc->regname; \
}; \
break; \
} \
__ret; })
struct mpc512x_psc_spi {
void (*cs_control)(struct spi_device *spi, bool on);
/* driver internal data */
int type;
void __iomem *psc;
struct mpc512x_psc_fifo __iomem *fifo;
unsigned int irq;
u8 bits_per_word;
struct clk *clk_mclk;
struct clk *clk_ipg;
u32 mclk_rate;
struct completion txisrdone;
};
/* controller state */
struct mpc512x_psc_spi_cs {
int bits_per_word;
int speed_hz;
};
/* set clock freq, clock ramp, bits per work
* if t is NULL then reset the values to the default values
*/
static int mpc512x_psc_spi_transfer_setup(struct spi_device *spi,
struct spi_transfer *t)
{
struct mpc512x_psc_spi_cs *cs = spi->controller_state;
cs->speed_hz = (t && t->speed_hz)
? t->speed_hz : spi->max_speed_hz;
cs->bits_per_word = (t && t->bits_per_word)
? t->bits_per_word : spi->bits_per_word;
cs->bits_per_word = ((cs->bits_per_word + 7) / 8) * 8;
return 0;
}
static void mpc512x_psc_spi_activate_cs(struct spi_device *spi)
{
struct mpc512x_psc_spi_cs *cs = spi->controller_state;
struct mpc512x_psc_spi *mps = spi_master_get_devdata(spi->master);
u32 sicr;
u32 ccr;
int speed;
u16 bclkdiv;
sicr = in_be32(psc_addr(mps, sicr));
/* Set clock phase and polarity */
if (spi->mode & SPI_CPHA)
sicr |= 0x00001000;
else
sicr &= ~0x00001000;
if (spi->mode & SPI_CPOL)
sicr |= 0x00002000;
else
sicr &= ~0x00002000;
if (spi->mode & SPI_LSB_FIRST)
sicr |= 0x10000000;
else
sicr &= ~0x10000000;
out_be32(psc_addr(mps, sicr), sicr);
ccr = in_be32(psc_addr(mps, ccr));
ccr &= 0xFF000000;
speed = cs->speed_hz;
if (!speed)
speed = 1000000; /* default 1MHz */
bclkdiv = (mps->mclk_rate / speed) - 1;
ccr |= (((bclkdiv & 0xff) << 16) | (((bclkdiv >> 8) & 0xff) << 8));
out_be32(psc_addr(mps, ccr), ccr);
mps->bits_per_word = cs->bits_per_word;
if (mps->cs_control && gpio_is_valid(spi->cs_gpio))
mps->cs_control(spi, (spi->mode & SPI_CS_HIGH) ? 1 : 0);
}
static void mpc512x_psc_spi_deactivate_cs(struct spi_device *spi)
{
struct mpc512x_psc_spi *mps = spi_master_get_devdata(spi->master);
if (mps->cs_control && gpio_is_valid(spi->cs_gpio))
mps->cs_control(spi, (spi->mode & SPI_CS_HIGH) ? 0 : 1);
}
/* extract and scale size field in txsz or rxsz */
#define MPC512x_PSC_FIFO_SZ(sz) ((sz & 0x7ff) << 2);
#define EOFBYTE 1
static int mpc512x_psc_spi_transfer_rxtx(struct spi_device *spi,
struct spi_transfer *t)
{
struct mpc512x_psc_spi *mps = spi_master_get_devdata(spi->master);
struct mpc512x_psc_fifo __iomem *fifo = mps->fifo;
size_t tx_len = t->len;
spi: mpc512x: improve throughput in the RX/TX func change the MPC512x SPI controller's transmission routine to increase throughput: allow the RX byte counter to "lag behind" the TX byte counter while iterating over the transfer's data, only wait for the remaining RX bytes at the very end of the transfer this approach eliminates delays in the milliseconds range, transfer times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct operation was tested by continuously transferring and comparing data from an SPI flash (more than 200GB in some 45 hours) background information on the motivation: one might assume that all the RX data should have been received when the TX data was sent, given the fact that we are the SPI master and provide all of the clock, but in practise there's a difference the ISR is triggered when the TX FIFO became empty, while transmission of the last item still occurs (from the TX hold and shift registers), sampling RX data on the opposite clock edge compared to the TX data adds another delay (half a bit period), and RX data needs to propagate from the reception buffer to the RX FIFO depending on the specific SoC implementation to cut it short: a difference between TX and RX byte counters during transmission is not just acceptable but should be considered the regular case, only the very end of the transfer needs to make sure that all of the RX data was received before deasserting the chip select and telling the caller that transmission has completed Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 20:03:50 +08:00
size_t rx_len = t->len;
u8 *tx_buf = (u8 *)t->tx_buf;
u8 *rx_buf = (u8 *)t->rx_buf;
if (!tx_buf && !rx_buf && t->len)
return -EINVAL;
spi: mpc512x: improve throughput in the RX/TX func change the MPC512x SPI controller's transmission routine to increase throughput: allow the RX byte counter to "lag behind" the TX byte counter while iterating over the transfer's data, only wait for the remaining RX bytes at the very end of the transfer this approach eliminates delays in the milliseconds range, transfer times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct operation was tested by continuously transferring and comparing data from an SPI flash (more than 200GB in some 45 hours) background information on the motivation: one might assume that all the RX data should have been received when the TX data was sent, given the fact that we are the SPI master and provide all of the clock, but in practise there's a difference the ISR is triggered when the TX FIFO became empty, while transmission of the last item still occurs (from the TX hold and shift registers), sampling RX data on the opposite clock edge compared to the TX data adds another delay (half a bit period), and RX data needs to propagate from the reception buffer to the RX FIFO depending on the specific SoC implementation to cut it short: a difference between TX and RX byte counters during transmission is not just acceptable but should be considered the regular case, only the very end of the transfer needs to make sure that all of the RX data was received before deasserting the chip select and telling the caller that transmission has completed Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 20:03:50 +08:00
while (rx_len || tx_len) {
size_t txcount;
u8 data;
size_t fifosz;
size_t rxcount;
spi: mpc512x: improve throughput in the RX/TX func change the MPC512x SPI controller's transmission routine to increase throughput: allow the RX byte counter to "lag behind" the TX byte counter while iterating over the transfer's data, only wait for the remaining RX bytes at the very end of the transfer this approach eliminates delays in the milliseconds range, transfer times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct operation was tested by continuously transferring and comparing data from an SPI flash (more than 200GB in some 45 hours) background information on the motivation: one might assume that all the RX data should have been received when the TX data was sent, given the fact that we are the SPI master and provide all of the clock, but in practise there's a difference the ISR is triggered when the TX FIFO became empty, while transmission of the last item still occurs (from the TX hold and shift registers), sampling RX data on the opposite clock edge compared to the TX data adds another delay (half a bit period), and RX data needs to propagate from the reception buffer to the RX FIFO depending on the specific SoC implementation to cut it short: a difference between TX and RX byte counters during transmission is not just acceptable but should be considered the regular case, only the very end of the transfer needs to make sure that all of the RX data was received before deasserting the chip select and telling the caller that transmission has completed Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 20:03:50 +08:00
int rxtries;
/*
spi: mpc512x: improve throughput in the RX/TX func change the MPC512x SPI controller's transmission routine to increase throughput: allow the RX byte counter to "lag behind" the TX byte counter while iterating over the transfer's data, only wait for the remaining RX bytes at the very end of the transfer this approach eliminates delays in the milliseconds range, transfer times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct operation was tested by continuously transferring and comparing data from an SPI flash (more than 200GB in some 45 hours) background information on the motivation: one might assume that all the RX data should have been received when the TX data was sent, given the fact that we are the SPI master and provide all of the clock, but in practise there's a difference the ISR is triggered when the TX FIFO became empty, while transmission of the last item still occurs (from the TX hold and shift registers), sampling RX data on the opposite clock edge compared to the TX data adds another delay (half a bit period), and RX data needs to propagate from the reception buffer to the RX FIFO depending on the specific SoC implementation to cut it short: a difference between TX and RX byte counters during transmission is not just acceptable but should be considered the regular case, only the very end of the transfer needs to make sure that all of the RX data was received before deasserting the chip select and telling the caller that transmission has completed Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 20:03:50 +08:00
* send the TX bytes in as large a chunk as possible
* but neither exceed the TX nor the RX FIFOs
*/
fifosz = MPC512x_PSC_FIFO_SZ(in_be32(&fifo->txsz));
txcount = min(fifosz, tx_len);
spi: mpc512x: improve throughput in the RX/TX func change the MPC512x SPI controller's transmission routine to increase throughput: allow the RX byte counter to "lag behind" the TX byte counter while iterating over the transfer's data, only wait for the remaining RX bytes at the very end of the transfer this approach eliminates delays in the milliseconds range, transfer times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct operation was tested by continuously transferring and comparing data from an SPI flash (more than 200GB in some 45 hours) background information on the motivation: one might assume that all the RX data should have been received when the TX data was sent, given the fact that we are the SPI master and provide all of the clock, but in practise there's a difference the ISR is triggered when the TX FIFO became empty, while transmission of the last item still occurs (from the TX hold and shift registers), sampling RX data on the opposite clock edge compared to the TX data adds another delay (half a bit period), and RX data needs to propagate from the reception buffer to the RX FIFO depending on the specific SoC implementation to cut it short: a difference between TX and RX byte counters during transmission is not just acceptable but should be considered the regular case, only the very end of the transfer needs to make sure that all of the RX data was received before deasserting the chip select and telling the caller that transmission has completed Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 20:03:50 +08:00
fifosz = MPC512x_PSC_FIFO_SZ(in_be32(&fifo->rxsz));
fifosz -= in_be32(&fifo->rxcnt) + 1;
txcount = min(fifosz, txcount);
if (txcount) {
/* fill the TX FIFO */
while (txcount-- > 0) {
data = tx_buf ? *tx_buf++ : 0;
if (tx_len == EOFBYTE && t->cs_change)
setbits32(&fifo->txcmd,
MPC512x_PSC_FIFO_EOF);
out_8(&fifo->txdata_8, data);
tx_len--;
}
spi: mpc512x: improve throughput in the RX/TX func change the MPC512x SPI controller's transmission routine to increase throughput: allow the RX byte counter to "lag behind" the TX byte counter while iterating over the transfer's data, only wait for the remaining RX bytes at the very end of the transfer this approach eliminates delays in the milliseconds range, transfer times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct operation was tested by continuously transferring and comparing data from an SPI flash (more than 200GB in some 45 hours) background information on the motivation: one might assume that all the RX data should have been received when the TX data was sent, given the fact that we are the SPI master and provide all of the clock, but in practise there's a difference the ISR is triggered when the TX FIFO became empty, while transmission of the last item still occurs (from the TX hold and shift registers), sampling RX data on the opposite clock edge compared to the TX data adds another delay (half a bit period), and RX data needs to propagate from the reception buffer to the RX FIFO depending on the specific SoC implementation to cut it short: a difference between TX and RX byte counters during transmission is not just acceptable but should be considered the regular case, only the very end of the transfer needs to make sure that all of the RX data was received before deasserting the chip select and telling the caller that transmission has completed Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 20:03:50 +08:00
/* have the ISR trigger when the TX FIFO is empty */
reinit_completion(&mps->txisrdone);
spi: mpc512x: improve throughput in the RX/TX func change the MPC512x SPI controller's transmission routine to increase throughput: allow the RX byte counter to "lag behind" the TX byte counter while iterating over the transfer's data, only wait for the remaining RX bytes at the very end of the transfer this approach eliminates delays in the milliseconds range, transfer times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct operation was tested by continuously transferring and comparing data from an SPI flash (more than 200GB in some 45 hours) background information on the motivation: one might assume that all the RX data should have been received when the TX data was sent, given the fact that we are the SPI master and provide all of the clock, but in practise there's a difference the ISR is triggered when the TX FIFO became empty, while transmission of the last item still occurs (from the TX hold and shift registers), sampling RX data on the opposite clock edge compared to the TX data adds another delay (half a bit period), and RX data needs to propagate from the reception buffer to the RX FIFO depending on the specific SoC implementation to cut it short: a difference between TX and RX byte counters during transmission is not just acceptable but should be considered the regular case, only the very end of the transfer needs to make sure that all of the RX data was received before deasserting the chip select and telling the caller that transmission has completed Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 20:03:50 +08:00
out_be32(&fifo->txisr, MPC512x_PSC_FIFO_EMPTY);
out_be32(&fifo->tximr, MPC512x_PSC_FIFO_EMPTY);
wait_for_completion(&mps->txisrdone);
}
spi: mpc512x: improve throughput in the RX/TX func change the MPC512x SPI controller's transmission routine to increase throughput: allow the RX byte counter to "lag behind" the TX byte counter while iterating over the transfer's data, only wait for the remaining RX bytes at the very end of the transfer this approach eliminates delays in the milliseconds range, transfer times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct operation was tested by continuously transferring and comparing data from an SPI flash (more than 200GB in some 45 hours) background information on the motivation: one might assume that all the RX data should have been received when the TX data was sent, given the fact that we are the SPI master and provide all of the clock, but in practise there's a difference the ISR is triggered when the TX FIFO became empty, while transmission of the last item still occurs (from the TX hold and shift registers), sampling RX data on the opposite clock edge compared to the TX data adds another delay (half a bit period), and RX data needs to propagate from the reception buffer to the RX FIFO depending on the specific SoC implementation to cut it short: a difference between TX and RX byte counters during transmission is not just acceptable but should be considered the regular case, only the very end of the transfer needs to make sure that all of the RX data was received before deasserting the chip select and telling the caller that transmission has completed Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 20:03:50 +08:00
/*
* consume as much RX data as the FIFO holds, while we
* iterate over the transfer's TX data length
*
* only insist in draining all the remaining RX bytes
* when the TX bytes were exhausted (that's at the very
* end of this transfer, not when still iterating over
* the transfer's chunks)
*/
rxtries = 50;
do {
/*
* grab whatever was in the FIFO when we started
* looking, don't bother fetching what was added to
* the FIFO while we read from it -- we'll return
* here eventually and prefer sending out remaining
* TX data
*/
fifosz = in_be32(&fifo->rxcnt);
rxcount = min(fifosz, rx_len);
while (rxcount-- > 0) {
data = in_8(&fifo->rxdata_8);
if (rx_buf)
*rx_buf++ = data;
rx_len--;
}
spi: mpc512x: improve throughput in the RX/TX func change the MPC512x SPI controller's transmission routine to increase throughput: allow the RX byte counter to "lag behind" the TX byte counter while iterating over the transfer's data, only wait for the remaining RX bytes at the very end of the transfer this approach eliminates delays in the milliseconds range, transfer times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct operation was tested by continuously transferring and comparing data from an SPI flash (more than 200GB in some 45 hours) background information on the motivation: one might assume that all the RX data should have been received when the TX data was sent, given the fact that we are the SPI master and provide all of the clock, but in practise there's a difference the ISR is triggered when the TX FIFO became empty, while transmission of the last item still occurs (from the TX hold and shift registers), sampling RX data on the opposite clock edge compared to the TX data adds another delay (half a bit period), and RX data needs to propagate from the reception buffer to the RX FIFO depending on the specific SoC implementation to cut it short: a difference between TX and RX byte counters during transmission is not just acceptable but should be considered the regular case, only the very end of the transfer needs to make sure that all of the RX data was received before deasserting the chip select and telling the caller that transmission has completed Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 20:03:50 +08:00
/*
* come back later if there still is TX data to send,
* bail out of the RX drain loop if all of the TX data
* was sent and all of the RX data was received (i.e.
* when the transmission has completed)
*/
if (tx_len)
break;
if (!rx_len)
break;
/*
* TX data transmission has completed while RX data
* is still pending -- that's a transient situation
* which depends on wire speed and specific
* hardware implementation details (buffering) yet
* should resolve very quickly
*
* just yield for a moment to not hog the CPU for
* too long when running SPI at low speed
*
* the timeout range is rather arbitrary and tries
* to balance throughput against system load; the
* chosen values result in a minimal timeout of 50
* times 10us and thus work at speeds as low as
* some 20kbps, while the maximum timeout at the
* transfer's end could be 5ms _if_ nothing else
* ticks in the system _and_ RX data still wasn't
* received, which only occurs in situations that
* are exceptional; removing the unpredictability
* of the timeout either decreases throughput
* (longer timeouts), or puts more load on the
* system (fixed short timeouts) or requires the
* use of a timeout API instead of a counter and an
* unknown inner delay
*/
usleep_range(10, 100);
} while (--rxtries > 0);
if (!tx_len && rx_len && !rxtries) {
/*
* not enough RX bytes even after several retries
* and the resulting rather long timeout?
*/
rxcount = in_be32(&fifo->rxcnt);
dev_warn(&spi->dev,
"short xfer, missing %zd RX bytes, FIFO level %zd\n",
rx_len, rxcount);
}
spi: mpc512x: improve throughput in the RX/TX func change the MPC512x SPI controller's transmission routine to increase throughput: allow the RX byte counter to "lag behind" the TX byte counter while iterating over the transfer's data, only wait for the remaining RX bytes at the very end of the transfer this approach eliminates delays in the milliseconds range, transfer times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct operation was tested by continuously transferring and comparing data from an SPI flash (more than 200GB in some 45 hours) background information on the motivation: one might assume that all the RX data should have been received when the TX data was sent, given the fact that we are the SPI master and provide all of the clock, but in practise there's a difference the ISR is triggered when the TX FIFO became empty, while transmission of the last item still occurs (from the TX hold and shift registers), sampling RX data on the opposite clock edge compared to the TX data adds another delay (half a bit period), and RX data needs to propagate from the reception buffer to the RX FIFO depending on the specific SoC implementation to cut it short: a difference between TX and RX byte counters during transmission is not just acceptable but should be considered the regular case, only the very end of the transfer needs to make sure that all of the RX data was received before deasserting the chip select and telling the caller that transmission has completed Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 20:03:50 +08:00
/*
* drain and drop RX data which "should not be there" in
* the first place, for undisturbed transmission this turns
* into a NOP (except for the FIFO level fetch)
*/
if (!tx_len && !rx_len) {
while (in_be32(&fifo->rxcnt))
in_8(&fifo->rxdata_8);
}
spi: mpc512x: improve throughput in the RX/TX func change the MPC512x SPI controller's transmission routine to increase throughput: allow the RX byte counter to "lag behind" the TX byte counter while iterating over the transfer's data, only wait for the remaining RX bytes at the very end of the transfer this approach eliminates delays in the milliseconds range, transfer times for e.g. 16MB of SPI flash data dropped from 31s to 9s, correct operation was tested by continuously transferring and comparing data from an SPI flash (more than 200GB in some 45 hours) background information on the motivation: one might assume that all the RX data should have been received when the TX data was sent, given the fact that we are the SPI master and provide all of the clock, but in practise there's a difference the ISR is triggered when the TX FIFO became empty, while transmission of the last item still occurs (from the TX hold and shift registers), sampling RX data on the opposite clock edge compared to the TX data adds another delay (half a bit period), and RX data needs to propagate from the reception buffer to the RX FIFO depending on the specific SoC implementation to cut it short: a difference between TX and RX byte counters during transmission is not just acceptable but should be considered the regular case, only the very end of the transfer needs to make sure that all of the RX data was received before deasserting the chip select and telling the caller that transmission has completed Signed-off-by: Gerhard Sittig <gsi@denx.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-06-03 20:03:50 +08:00
}
return 0;
}
static int mpc512x_psc_spi_msg_xfer(struct spi_master *master,
struct spi_message *m)
{
struct spi_device *spi;
unsigned cs_change;
int status;
struct spi_transfer *t;
spi = m->spi;
cs_change = 1;
status = 0;
list_for_each_entry(t, &m->transfers, transfer_list) {
if (t->bits_per_word || t->speed_hz) {
status = mpc512x_psc_spi_transfer_setup(spi, t);
if (status < 0)
break;
}
if (cs_change)
mpc512x_psc_spi_activate_cs(spi);
cs_change = t->cs_change;
status = mpc512x_psc_spi_transfer_rxtx(spi, t);
if (status)
break;
m->actual_length += t->len;
if (t->delay_usecs)
udelay(t->delay_usecs);
if (cs_change)
mpc512x_psc_spi_deactivate_cs(spi);
}
m->status = status;
if (m->complete)
m->complete(m->context);
if (status || !cs_change)
mpc512x_psc_spi_deactivate_cs(spi);
mpc512x_psc_spi_transfer_setup(spi, NULL);
spi_finalize_current_message(master);
return status;
}
static int mpc512x_psc_spi_prep_xfer_hw(struct spi_master *master)
{
struct mpc512x_psc_spi *mps = spi_master_get_devdata(master);
dev_dbg(&master->dev, "%s()\n", __func__);
/* Zero MR2 */
in_8(psc_addr(mps, mr2));
out_8(psc_addr(mps, mr2), 0x0);
/* enable transmitter/receiver */
out_8(psc_addr(mps, command), MPC52xx_PSC_TX_ENABLE | MPC52xx_PSC_RX_ENABLE);
return 0;
}
static int mpc512x_psc_spi_unprep_xfer_hw(struct spi_master *master)
{
struct mpc512x_psc_spi *mps = spi_master_get_devdata(master);
struct mpc512x_psc_fifo __iomem *fifo = mps->fifo;
dev_dbg(&master->dev, "%s()\n", __func__);
/* disable transmitter/receiver and fifo interrupt */
out_8(psc_addr(mps, command), MPC52xx_PSC_TX_DISABLE | MPC52xx_PSC_RX_DISABLE);
out_be32(&fifo->tximr, 0);
return 0;
}
static int mpc512x_psc_spi_setup(struct spi_device *spi)
{
struct mpc512x_psc_spi_cs *cs = spi->controller_state;
int ret;
if (spi->bits_per_word % 8)
return -EINVAL;
if (!cs) {
cs = kzalloc(sizeof *cs, GFP_KERNEL);
if (!cs)
return -ENOMEM;
if (gpio_is_valid(spi->cs_gpio)) {
ret = gpio_request(spi->cs_gpio, dev_name(&spi->dev));
if (ret) {
dev_err(&spi->dev, "can't get CS gpio: %d\n",
ret);
kfree(cs);
return ret;
}
gpio_direction_output(spi->cs_gpio,
spi->mode & SPI_CS_HIGH ? 0 : 1);
}
spi->controller_state = cs;
}
cs->bits_per_word = spi->bits_per_word;
cs->speed_hz = spi->max_speed_hz;
return 0;
}
static void mpc512x_psc_spi_cleanup(struct spi_device *spi)
{
if (gpio_is_valid(spi->cs_gpio))
gpio_free(spi->cs_gpio);
kfree(spi->controller_state);
}
static int mpc512x_psc_spi_port_config(struct spi_master *master,
struct mpc512x_psc_spi *mps)
{
struct mpc512x_psc_fifo __iomem *fifo = mps->fifo;
u32 sicr;
u32 ccr;
int speed;
u16 bclkdiv;
/* Reset the PSC into a known state */
out_8(psc_addr(mps, command), MPC52xx_PSC_RST_RX);
out_8(psc_addr(mps, command), MPC52xx_PSC_RST_TX);
out_8(psc_addr(mps, command), MPC52xx_PSC_TX_DISABLE | MPC52xx_PSC_RX_DISABLE);
/* Disable psc interrupts all useful interrupts are in fifo */
out_be16(psc_addr(mps, isr_imr.imr), 0);
/* Disable fifo interrupts, will be enabled later */
out_be32(&fifo->tximr, 0);
out_be32(&fifo->rximr, 0);
/* Setup fifo slice address and size */
/*out_be32(&fifo->txsz, 0x0fe00004);*/
/*out_be32(&fifo->rxsz, 0x0ff00004);*/
sicr = 0x01000000 | /* SIM = 0001 -- 8 bit */
0x00800000 | /* GenClk = 1 -- internal clk */
0x00008000 | /* SPI = 1 */
0x00004000 | /* MSTR = 1 -- SPI master */
0x00000800; /* UseEOF = 1 -- SS low until EOF */
out_be32(psc_addr(mps, sicr), sicr);
ccr = in_be32(psc_addr(mps, ccr));
ccr &= 0xFF000000;
speed = 1000000; /* default 1MHz */
bclkdiv = (mps->mclk_rate / speed) - 1;
ccr |= (((bclkdiv & 0xff) << 16) | (((bclkdiv >> 8) & 0xff) << 8));
out_be32(psc_addr(mps, ccr), ccr);
/* Set 2ms DTL delay */
out_8(psc_addr(mps, ctur), 0x00);
out_8(psc_addr(mps, ctlr), 0x82);
/* we don't use the alarms */
out_be32(&fifo->rxalarm, 0xfff);
out_be32(&fifo->txalarm, 0);
/* Enable FIFO slices for Rx/Tx */
out_be32(&fifo->rxcmd,
MPC512x_PSC_FIFO_ENABLE_SLICE | MPC512x_PSC_FIFO_ENABLE_DMA);
out_be32(&fifo->txcmd,
MPC512x_PSC_FIFO_ENABLE_SLICE | MPC512x_PSC_FIFO_ENABLE_DMA);
mps->bits_per_word = 8;
return 0;
}
static irqreturn_t mpc512x_psc_spi_isr(int irq, void *dev_id)
{
struct mpc512x_psc_spi *mps = (struct mpc512x_psc_spi *)dev_id;
struct mpc512x_psc_fifo __iomem *fifo = mps->fifo;
/* clear interrupt and wake up the rx/tx routine */
if (in_be32(&fifo->txisr) &
in_be32(&fifo->tximr) & MPC512x_PSC_FIFO_EMPTY) {
out_be32(&fifo->txisr, MPC512x_PSC_FIFO_EMPTY);
out_be32(&fifo->tximr, 0);
complete(&mps->txisrdone);
return IRQ_HANDLED;
}
return IRQ_NONE;
}
static void mpc512x_spi_cs_control(struct spi_device *spi, bool onoff)
{
gpio_set_value(spi->cs_gpio, onoff);
}
static int mpc512x_psc_spi_do_probe(struct device *dev, u32 regaddr,
u32 size, unsigned int irq)
{
struct fsl_spi_platform_data *pdata = dev_get_platdata(dev);
struct mpc512x_psc_spi *mps;
struct spi_master *master;
int ret;
void *tempp;
struct clk *clk;
master = spi_alloc_master(dev, sizeof *mps);
if (master == NULL)
return -ENOMEM;
dev_set_drvdata(dev, master);
mps = spi_master_get_devdata(master);
mps->type = (int)of_device_get_match_data(dev);
mps->irq = irq;
if (pdata == NULL) {
mps->cs_control = mpc512x_spi_cs_control;
} else {
mps->cs_control = pdata->cs_control;
master->bus_num = pdata->bus_num;
master->num_chipselect = pdata->max_chipselect;
}
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LSB_FIRST;
master->setup = mpc512x_psc_spi_setup;
master->prepare_transfer_hardware = mpc512x_psc_spi_prep_xfer_hw;
master->transfer_one_message = mpc512x_psc_spi_msg_xfer;
master->unprepare_transfer_hardware = mpc512x_psc_spi_unprep_xfer_hw;
master->cleanup = mpc512x_psc_spi_cleanup;
master->dev.of_node = dev->of_node;
tempp = devm_ioremap(dev, regaddr, size);
if (!tempp) {
dev_err(dev, "could not ioremap I/O port range\n");
ret = -EFAULT;
goto free_master;
}
mps->psc = tempp;
mps->fifo =
(struct mpc512x_psc_fifo *)(tempp + sizeof(struct mpc52xx_psc));
ret = devm_request_irq(dev, mps->irq, mpc512x_psc_spi_isr, IRQF_SHARED,
"mpc512x-psc-spi", mps);
if (ret)
goto free_master;
init_completion(&mps->txisrdone);
clk = devm_clk_get(dev, "mclk");
if (IS_ERR(clk)) {
ret = PTR_ERR(clk);
goto free_master;
}
ret = clk_prepare_enable(clk);
if (ret)
goto free_master;
mps->clk_mclk = clk;
mps->mclk_rate = clk_get_rate(clk);
clk = devm_clk_get(dev, "ipg");
if (IS_ERR(clk)) {
ret = PTR_ERR(clk);
goto free_mclk_clock;
}
ret = clk_prepare_enable(clk);
if (ret)
goto free_mclk_clock;
mps->clk_ipg = clk;
ret = mpc512x_psc_spi_port_config(master, mps);
if (ret < 0)
goto free_ipg_clock;
ret = devm_spi_register_master(dev, master);
if (ret < 0)
goto free_ipg_clock;
return ret;
free_ipg_clock:
clk_disable_unprepare(mps->clk_ipg);
free_mclk_clock:
clk_disable_unprepare(mps->clk_mclk);
free_master:
spi_master_put(master);
return ret;
}
static int mpc512x_psc_spi_do_remove(struct device *dev)
{
struct spi_master *master = dev_get_drvdata(dev);
struct mpc512x_psc_spi *mps = spi_master_get_devdata(master);
clk_disable_unprepare(mps->clk_mclk);
clk_disable_unprepare(mps->clk_ipg);
return 0;
}
static int mpc512x_psc_spi_of_probe(struct platform_device *op)
{
const u32 *regaddr_p;
u64 regaddr64, size64;
regaddr_p = of_get_address(op->dev.of_node, 0, &size64, NULL);
if (!regaddr_p) {
dev_err(&op->dev, "Invalid PSC address\n");
return -EINVAL;
}
regaddr64 = of_translate_address(op->dev.of_node, regaddr_p);
return mpc512x_psc_spi_do_probe(&op->dev, (u32) regaddr64, (u32) size64,
irq_of_parse_and_map(op->dev.of_node, 0));
}
static int mpc512x_psc_spi_of_remove(struct platform_device *op)
{
return mpc512x_psc_spi_do_remove(&op->dev);
}
static const struct of_device_id mpc512x_psc_spi_of_match[] = {
{ .compatible = "fsl,mpc5121-psc-spi", .data = (void *)TYPE_MPC5121 },
{ .compatible = "fsl,mpc5125-psc-spi", .data = (void *)TYPE_MPC5125 },
{},
};
MODULE_DEVICE_TABLE(of, mpc512x_psc_spi_of_match);
static struct platform_driver mpc512x_psc_spi_of_driver = {
.probe = mpc512x_psc_spi_of_probe,
.remove = mpc512x_psc_spi_of_remove,
.driver = {
.name = "mpc512x-psc-spi",
.of_match_table = mpc512x_psc_spi_of_match,
},
};
module_platform_driver(mpc512x_psc_spi_of_driver);
MODULE_AUTHOR("John Rigby");
MODULE_DESCRIPTION("MPC512x PSC SPI Driver");
MODULE_LICENSE("GPL");