p71924506
/
linux_old1
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
linux_old1/arch/arm/common/bL_switcher.c

317 lines
8.1 KiB
C
Raw Normal View History

ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
/*
* arch/arm/common/bL_switcher.c -- big.LITTLE cluster switcher core driver
*
* Created by: Nicolas Pitre, March 2012
* Copyright: (C) 2012-2013 Linaro Limited
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/sched.h>
#include <linux/interrupt.h>
#include <linux/cpu_pm.h>
ARM: bL_switcher: move to dedicated threads rather than workqueues The workqueues are problematic as they may be contended. They can't be scheduled with top priority either. Also the optimization in bL_switch_request() to skip the workqueue entirely when the target CPU and the calling CPU were the same didn't allow for bL_switch_request() to be called from atomic context, as might be the case for some cpufreq drivers. Let's move to dedicated kthreads instead. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-10-26 14:36:17 +08:00
#include <linux/cpu.h>
ARM: bL_switcher: add clockevent save/restore support Per-CPU timers that are shutdown when a CPU is switched over must be disabled upon switching and reprogrammed on the inbound CPU by relying on the clock events management API. save/restore sequence is executed with irqs disabled as mandated by the clock events API. The next_event is an absolute time, hence, when the inbound CPU resumes, if the timer has expired the min delta is forced into the tick device to fire after few cycles. This patch adds switching support for clock events that are per-CPU and have to be migrated when a switch takes place; the cpumask of the clock event device is checked against the cpumask of the current cpu, and if they match, the clockevent device mode is saved and it is put in shutdown mode. Resume code reprogrammes the tick device accordingly. Tested on A15/A7 fast models and architected timers. Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-05-16 22:55:54 +08:00
#include <linux/cpumask.h>
ARM: bL_switcher: move to dedicated threads rather than workqueues The workqueues are problematic as they may be contended. They can't be scheduled with top priority either. Also the optimization in bL_switch_request() to skip the workqueue entirely when the target CPU and the calling CPU were the same didn't allow for bL_switch_request() to be called from atomic context, as might be the case for some cpufreq drivers. Let's move to dedicated kthreads instead. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-10-26 14:36:17 +08:00
#include <linux/kthread.h>
#include <linux/wait.h>
ARM: bL_switcher: add clockevent save/restore support Per-CPU timers that are shutdown when a CPU is switched over must be disabled upon switching and reprogrammed on the inbound CPU by relying on the clock events management API. save/restore sequence is executed with irqs disabled as mandated by the clock events API. The next_event is an absolute time, hence, when the inbound CPU resumes, if the timer has expired the min delta is forced into the tick device to fire after few cycles. This patch adds switching support for clock events that are per-CPU and have to be migrated when a switch takes place; the cpumask of the clock event device is checked against the cpumask of the current cpu, and if they match, the clockevent device mode is saved and it is put in shutdown mode. Resume code reprogrammes the tick device accordingly. Tested on A15/A7 fast models and architected timers. Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-05-16 22:55:54 +08:00
#include <linux/clockchips.h>
#include <linux/hrtimer.h>
#include <linux/tick.h>
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
#include <linux/mm.h>
#include <linux/string.h>
#include <linux/irqchip/arm-gic.h>
#include <asm/smp_plat.h>
#include <asm/suspend.h>
#include <asm/mcpm.h>
#include <asm/bL_switcher.h>
/*
* Use our own MPIDR accessors as the generic ones in asm/cputype.h have
* __attribute_const__ and we don't want the compiler to assume any
* constness here as the value _does_ change along some code paths.
*/
static int read_mpidr(void)
{
unsigned int id;
asm volatile ("mrc p15, 0, %0, c0, c0, 5" : "=r" (id));
return id & MPIDR_HWID_BITMASK;
}
/*
* bL switcher core code.
*/
static void bL_do_switch(void *_unused)
{
unsigned mpidr, cpuid, clusterid, ob_cluster, ib_cluster;
/*
* We now have a piece of stack borrowed from the init task's.
* Let's also switch to init_mm right away to match it.
*/
cpu_switch_mm(init_mm.pgd, &init_mm);
pr_debug("%s\n", __func__);
mpidr = read_mpidr();
cpuid = MPIDR_AFFINITY_LEVEL(mpidr, 0);
clusterid = MPIDR_AFFINITY_LEVEL(mpidr, 1);
ob_cluster = clusterid;
ib_cluster = clusterid ^ 1;
/*
* Our state has been saved at this point. Let's release our
* inbound CPU.
*/
mcpm_set_entry_vector(cpuid, ib_cluster, cpu_resume);
sev();
/*
* From this point, we must assume that our counterpart CPU might
* have taken over in its parallel world already, as if execution
* just returned from cpu_suspend(). It is therefore important to
* be very careful not to make any change the other guy is not
* expecting. This is why we need stack isolation.
*
* Fancy under cover tasks could be performed here. For now
* we have none.
*/
/* Let's put ourself down. */
mcpm_cpu_power_down();
/* should never get here */
BUG();
}
/*
* Stack isolation. To ensure 'current' remains valid, we just borrow
* a slice of the init/idle task which should be fairly lightly used.
* The borrowed area starts just above the thread_info structure located
* at the very bottom of the stack, aligned to a cache line.
*/
#define STACK_SIZE 256
extern void call_with_stack(void (*fn)(void *), void *arg, void *sp);
static int bL_switchpoint(unsigned long _arg)
{
unsigned int mpidr = read_mpidr();
unsigned int cpuid = MPIDR_AFFINITY_LEVEL(mpidr, 0);
unsigned int clusterid = MPIDR_AFFINITY_LEVEL(mpidr, 1);
unsigned int cpu_index = cpuid + clusterid * MAX_CPUS_PER_CLUSTER;
void *stack = &init_thread_info + 1;
stack = PTR_ALIGN(stack, L1_CACHE_BYTES);
stack += cpu_index * STACK_SIZE + STACK_SIZE;
call_with_stack(bL_do_switch, (void *)_arg, stack);
BUG();
}
/*
* Generic switcher interface
*/
/*
* bL_switch_to - Switch to a specific cluster for the current CPU
* @new_cluster_id: the ID of the cluster to switch to.
*
* This function must be called on the CPU to be switched.
* Returns 0 on success, else a negative status code.
*/
static int bL_switch_to(unsigned int new_cluster_id)
{
unsigned int mpidr, cpuid, clusterid, ob_cluster, ib_cluster, this_cpu;
ARM: bL_switcher: add clockevent save/restore support Per-CPU timers that are shutdown when a CPU is switched over must be disabled upon switching and reprogrammed on the inbound CPU by relying on the clock events management API. save/restore sequence is executed with irqs disabled as mandated by the clock events API. The next_event is an absolute time, hence, when the inbound CPU resumes, if the timer has expired the min delta is forced into the tick device to fire after few cycles. This patch adds switching support for clock events that are per-CPU and have to be migrated when a switch takes place; the cpumask of the clock event device is checked against the cpumask of the current cpu, and if they match, the clockevent device mode is saved and it is put in shutdown mode. Resume code reprogrammes the tick device accordingly. Tested on A15/A7 fast models and architected timers. Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-05-16 22:55:54 +08:00
struct tick_device *tdev;
enum clock_event_mode tdev_mode;
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
int ret;
mpidr = read_mpidr();
cpuid = MPIDR_AFFINITY_LEVEL(mpidr, 0);
clusterid = MPIDR_AFFINITY_LEVEL(mpidr, 1);
ob_cluster = clusterid;
ib_cluster = clusterid ^ 1;
if (new_cluster_id == clusterid)
return 0;
pr_debug("before switch: CPU %d in cluster %d\n", cpuid, clusterid);
/* Close the gate for our entry vectors */
mcpm_set_entry_vector(cpuid, ob_cluster, NULL);
mcpm_set_entry_vector(cpuid, ib_cluster, NULL);
/*
* Let's wake up the inbound CPU now in case it requires some delay
* to come online, but leave it gated in our entry vector code.
*/
ret = mcpm_cpu_power_up(cpuid, ib_cluster);
if (ret) {
pr_err("%s: mcpm_cpu_power_up() returned %d\n", __func__, ret);
return ret;
}
/*
* From this point we are entering the switch critical zone
* and can't take any interrupts anymore.
*/
local_irq_disable();
local_fiq_disable();
this_cpu = smp_processor_id();
/* redirect GIC's SGIs to our counterpart */
gic_migrate_target(cpuid + ib_cluster*4);
/*
* Raise a SGI on the inbound CPU to make sure it doesn't stall
* in a possible WFI, such as in mcpm_power_down().
*/
arch_send_wakeup_ipi_mask(cpumask_of(this_cpu));
ARM: bL_switcher: add clockevent save/restore support Per-CPU timers that are shutdown when a CPU is switched over must be disabled upon switching and reprogrammed on the inbound CPU by relying on the clock events management API. save/restore sequence is executed with irqs disabled as mandated by the clock events API. The next_event is an absolute time, hence, when the inbound CPU resumes, if the timer has expired the min delta is forced into the tick device to fire after few cycles. This patch adds switching support for clock events that are per-CPU and have to be migrated when a switch takes place; the cpumask of the clock event device is checked against the cpumask of the current cpu, and if they match, the clockevent device mode is saved and it is put in shutdown mode. Resume code reprogrammes the tick device accordingly. Tested on A15/A7 fast models and architected timers. Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-05-16 22:55:54 +08:00
tdev = tick_get_device(this_cpu);
if (tdev && !cpumask_equal(tdev->evtdev->cpumask, cpumask_of(this_cpu)))
tdev = NULL;
if (tdev) {
tdev_mode = tdev->evtdev->mode;
clockevents_set_mode(tdev->evtdev, CLOCK_EVT_MODE_SHUTDOWN);
}
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
ret = cpu_pm_enter();
/* we can not tolerate errors at this point */
if (ret)
panic("%s: cpu_pm_enter() returned %d\n", __func__, ret);
/* Flip the cluster in the CPU logical map for this CPU. */
cpu_logical_map(this_cpu) ^= (1 << 8);
/* Let's do the actual CPU switch. */
ret = cpu_suspend(0, bL_switchpoint);
if (ret > 0)
panic("%s: cpu_suspend() returned %d\n", __func__, ret);
/* We are executing on the inbound CPU at this point */
mpidr = read_mpidr();
cpuid = MPIDR_AFFINITY_LEVEL(mpidr, 0);
clusterid = MPIDR_AFFINITY_LEVEL(mpidr, 1);
pr_debug("after switch: CPU %d in cluster %d\n", cpuid, clusterid);
BUG_ON(clusterid != ib_cluster);
mcpm_cpu_powered_up();
ret = cpu_pm_exit();
ARM: bL_switcher: add clockevent save/restore support Per-CPU timers that are shutdown when a CPU is switched over must be disabled upon switching and reprogrammed on the inbound CPU by relying on the clock events management API. save/restore sequence is executed with irqs disabled as mandated by the clock events API. The next_event is an absolute time, hence, when the inbound CPU resumes, if the timer has expired the min delta is forced into the tick device to fire after few cycles. This patch adds switching support for clock events that are per-CPU and have to be migrated when a switch takes place; the cpumask of the clock event device is checked against the cpumask of the current cpu, and if they match, the clockevent device mode is saved and it is put in shutdown mode. Resume code reprogrammes the tick device accordingly. Tested on A15/A7 fast models and architected timers. Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-05-16 22:55:54 +08:00
if (tdev) {
clockevents_set_mode(tdev->evtdev, tdev_mode);
clockevents_program_event(tdev->evtdev,
tdev->evtdev->next_event, 1);
}
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
local_fiq_enable();
local_irq_enable();
if (ret)
pr_err("%s exiting with error %d\n", __func__, ret);
return ret;
}
ARM: bL_switcher: move to dedicated threads rather than workqueues The workqueues are problematic as they may be contended. They can't be scheduled with top priority either. Also the optimization in bL_switch_request() to skip the workqueue entirely when the target CPU and the calling CPU were the same didn't allow for bL_switch_request() to be called from atomic context, as might be the case for some cpufreq drivers. Let's move to dedicated kthreads instead. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-10-26 14:36:17 +08:00
struct bL_thread {
struct task_struct *task;
wait_queue_head_t wq;
int wanted_cluster;
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
};
ARM: bL_switcher: move to dedicated threads rather than workqueues The workqueues are problematic as they may be contended. They can't be scheduled with top priority either. Also the optimization in bL_switch_request() to skip the workqueue entirely when the target CPU and the calling CPU were the same didn't allow for bL_switch_request() to be called from atomic context, as might be the case for some cpufreq drivers. Let's move to dedicated kthreads instead. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-10-26 14:36:17 +08:00
static struct bL_thread bL_threads[NR_CPUS];
static int bL_switcher_thread(void *arg)
{
struct bL_thread *t = arg;
struct sched_param param = { .sched_priority = 1 };
int cluster;
sched_setscheduler_nocheck(current, SCHED_FIFO, &param);
do {
if (signal_pending(current))
flush_signals(current);
wait_event_interruptible(t->wq,
t->wanted_cluster != -1 ||
kthread_should_stop());
cluster = xchg(&t->wanted_cluster, -1);
if (cluster != -1)
bL_switch_to(cluster);
} while (!kthread_should_stop());
return 0;
}
static struct task_struct * __init bL_switcher_thread_create(int cpu, void *arg)
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
{
ARM: bL_switcher: move to dedicated threads rather than workqueues The workqueues are problematic as they may be contended. They can't be scheduled with top priority either. Also the optimization in bL_switch_request() to skip the workqueue entirely when the target CPU and the calling CPU were the same didn't allow for bL_switch_request() to be called from atomic context, as might be the case for some cpufreq drivers. Let's move to dedicated kthreads instead. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-10-26 14:36:17 +08:00
struct task_struct *task;
task = kthread_create_on_node(bL_switcher_thread, arg,
cpu_to_node(cpu), "kswitcher_%d", cpu);
if (!IS_ERR(task)) {
kthread_bind(task, cpu);
wake_up_process(task);
} else
pr_err("%s failed for CPU %d\n", __func__, cpu);
return task;
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
}
/*
* bL_switch_request - Switch to a specific cluster for the given CPU
*
* @cpu: the CPU to switch
* @new_cluster_id: the ID of the cluster to switch to.
*
ARM: bL_switcher: move to dedicated threads rather than workqueues The workqueues are problematic as they may be contended. They can't be scheduled with top priority either. Also the optimization in bL_switch_request() to skip the workqueue entirely when the target CPU and the calling CPU were the same didn't allow for bL_switch_request() to be called from atomic context, as might be the case for some cpufreq drivers. Let's move to dedicated kthreads instead. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-10-26 14:36:17 +08:00
* This function causes a cluster switch on the given CPU by waking up
* the appropriate switcher thread. This function may or may not return
* before the switch has occurred.
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
*/
ARM: bL_switcher: move to dedicated threads rather than workqueues The workqueues are problematic as they may be contended. They can't be scheduled with top priority either. Also the optimization in bL_switch_request() to skip the workqueue entirely when the target CPU and the calling CPU were the same didn't allow for bL_switch_request() to be called from atomic context, as might be the case for some cpufreq drivers. Let's move to dedicated kthreads instead. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-10-26 14:36:17 +08:00
int bL_switch_request(unsigned int cpu, unsigned int new_cluster_id)
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
{
ARM: bL_switcher: move to dedicated threads rather than workqueues The workqueues are problematic as they may be contended. They can't be scheduled with top priority either. Also the optimization in bL_switch_request() to skip the workqueue entirely when the target CPU and the calling CPU were the same didn't allow for bL_switch_request() to be called from atomic context, as might be the case for some cpufreq drivers. Let's move to dedicated kthreads instead. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-10-26 14:36:17 +08:00
struct bL_thread *t;
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
ARM: bL_switcher: move to dedicated threads rather than workqueues The workqueues are problematic as they may be contended. They can't be scheduled with top priority either. Also the optimization in bL_switch_request() to skip the workqueue entirely when the target CPU and the calling CPU were the same didn't allow for bL_switch_request() to be called from atomic context, as might be the case for some cpufreq drivers. Let's move to dedicated kthreads instead. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-10-26 14:36:17 +08:00
if (cpu >= ARRAY_SIZE(bL_threads)) {
pr_err("%s: cpu %d out of bounds\n", __func__, cpu);
return -EINVAL;
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
}
ARM: bL_switcher: move to dedicated threads rather than workqueues The workqueues are problematic as they may be contended. They can't be scheduled with top priority either. Also the optimization in bL_switch_request() to skip the workqueue entirely when the target CPU and the calling CPU were the same didn't allow for bL_switch_request() to be called from atomic context, as might be the case for some cpufreq drivers. Let's move to dedicated kthreads instead. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-10-26 14:36:17 +08:00
t = &bL_threads[cpu];
if (IS_ERR(t->task))
return PTR_ERR(t->task);
if (!t->task)
return -ESRCH;
t->wanted_cluster = new_cluster_id;
wake_up(&t->wq);
return 0;
ARM: b.L: core switcher code This is the core code implementing big.LITTLE switcher functionality. Rationale for this code is available here: http://lwn.net/Articles/481055/ The main entry point for a switch request is: void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id) If the calling CPU is not the wanted one, this wrapper takes care of sending the request to the appropriate CPU with schedule_work_on(). At the moment the core switch operation is handled by bL_switch_to() which must be called on the CPU for which a switch is requested. What this code does: * Return early if the current cluster is the wanted one. * Close the gate in the kernel entry vector for both the inbound and outbound CPUs. * Wake up the inbound CPU so it can perform its reset sequence in parallel up to the kernel entry vector gate. * Migrate all interrupts in the GIC targeting the outbound CPU interface to the inbound CPU interface, including SGIs. This is performed by gic_migrate_target() in drivers/irqchip/irq-gic.c. * Call cpu_pm_enter() which takes care of flushing the VFP state to RAM and save the CPU interface config from the GIC to RAM. * Modify the cpu_logical_map to refer to the inbound physical CPU. * Call cpu_suspend() which saves the CPU state (general purpose registers, page table address) onto the stack and store the resulting stack pointer in an array indexed by the updated cpu_logical_map, then call the provided shutdown function. This happens in arch/arm/kernel/sleep.S. At this point, the provided shutdown function executed by the outbound CPU ungates the inbound CPU. Therefore the inbound CPU: * Picks up the saved stack pointer in the array indexed by its MPIDR in arch/arm/kernel/sleep.S. * The MMU and caches are re-enabled using the saved state on the provided stack, just like if this was a resume operation from a suspended state. * Then cpu_suspend() returns, although this is on the inbound CPU rather than the outbound CPU which called it initially. * The function cpu_pm_exit() is called which effect is to restore the CPU interface state in the GIC using the state previously saved by the outbound CPU. * Exit of bL_switch_to() to resume normal kernel execution on the new CPU. However, the outbound CPU is potentially still running in parallel while the inbound CPU is resuming normal kernel execution, hence we need per CPU stack isolation to execute bL_do_switch(). After the outbound CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to: * Clean its L1 cache. * If it is the last CPU still alive in its cluster (last man standing), it also cleans its L2 cache and disables cache snooping from the other cluster. * Power down the CPU (or whole cluster). Code called from bL_do_switch() might end up referencing 'current' for some reasons. However, 'current' is derived from the stack pointer. With any arbitrary stack, the returned value for 'current' and any dereferenced values through it are just random garbage which may lead to segmentation faults. The active page table during the execution of bL_do_switch() is also a problem. There is no guarantee that the inbound CPU won't destroy the corresponding task which would free the attached page table while the outbound CPU is still running and relying on it. To solve both issues, we borrow some of the task space belonging to the init/idle task which, by its nature, is lightly used and therefore is unlikely to clash with our usage. The init task is also never going away. Right now the logical CPU number is assumed to be equivalent to the physical CPU number within each cluster. The kernel should also be booted with only one cluster active. These limitations will be lifted eventually. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-04-12 14:56:10 +08:00
}
EXPORT_SYMBOL_GPL(bL_switch_request);
ARM: bL_switcher: move to dedicated threads rather than workqueues The workqueues are problematic as they may be contended. They can't be scheduled with top priority either. Also the optimization in bL_switch_request() to skip the workqueue entirely when the target CPU and the calling CPU were the same didn't allow for bL_switch_request() to be called from atomic context, as might be the case for some cpufreq drivers. Let's move to dedicated kthreads instead. Signed-off-by: Nicolas Pitre <nico@linaro.org>
2012-10-26 14:36:17 +08:00
static int __init bL_switcher_init(void)
{
int cpu;
pr_info("big.LITTLE switcher initializing\n");
for_each_online_cpu(cpu) {
struct bL_thread *t = &bL_threads[cpu];
init_waitqueue_head(&t->wq);
t->wanted_cluster = -1;
t->task = bL_switcher_thread_create(cpu, t);
}
pr_info("big.LITTLE switcher initialized\n");
return 0;
}
late_initcall(bL_switcher_init);