linux_old1/net/wireless/core.c

941 lines
23 KiB
C
Raw Normal View History

/*
* This is the linux wireless configuration interface.
*
* Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
*/
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/if.h>
#include <linux/module.h>
#include <linux/err.h>
#include <linux/list.h>
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 16:04:11 +08:00
#include <linux/slab.h>
#include <linux/nl80211.h>
#include <linux/debugfs.h>
#include <linux/notifier.h>
#include <linux/device.h>
#include <linux/etherdevice.h>
#include <linux/rtnetlink.h>
#include <linux/sched.h>
#include <net/genetlink.h>
#include <net/cfg80211.h>
#include "nl80211.h"
#include "core.h"
#include "sysfs.h"
#include "debugfs.h"
#include "wext-compat.h"
#include "ethtool.h"
/* name for sysfs, %d is appended */
#define PHY_NAME "phy"
MODULE_AUTHOR("Johannes Berg");
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("wireless configuration support");
/* RCU-protected (and cfg80211_mutex for writers) */
LIST_HEAD(cfg80211_rdev_list);
int cfg80211_rdev_list_generation;
DEFINE_MUTEX(cfg80211_mutex);
/* for debugfs */
static struct dentry *ieee80211_debugfs_dir;
/* for the cleanup, scan and event works */
struct workqueue_struct *cfg80211_wq;
/* requires cfg80211_mutex to be held! */
struct cfg80211_registered_device *cfg80211_rdev_by_wiphy_idx(int wiphy_idx)
{
struct cfg80211_registered_device *result = NULL, *rdev;
if (!wiphy_idx_valid(wiphy_idx))
return NULL;
assert_cfg80211_lock();
list_for_each_entry(rdev, &cfg80211_rdev_list, list) {
if (rdev->wiphy_idx == wiphy_idx) {
result = rdev;
break;
}
}
return result;
}
int get_wiphy_idx(struct wiphy *wiphy)
{
struct cfg80211_registered_device *rdev;
if (!wiphy)
return WIPHY_IDX_STALE;
rdev = wiphy_to_dev(wiphy);
return rdev->wiphy_idx;
}
/* requires cfg80211_rdev_mutex to be held! */
struct wiphy *wiphy_idx_to_wiphy(int wiphy_idx)
{
struct cfg80211_registered_device *rdev;
if (!wiphy_idx_valid(wiphy_idx))
return NULL;
assert_cfg80211_lock();
rdev = cfg80211_rdev_by_wiphy_idx(wiphy_idx);
if (!rdev)
return NULL;
return &rdev->wiphy;
}
/* requires cfg80211_mutex to be held! */
struct cfg80211_registered_device *
__cfg80211_rdev_from_info(struct genl_info *info)
{
int ifindex;
struct cfg80211_registered_device *bywiphyidx = NULL, *byifidx = NULL;
struct net_device *dev;
int err = -EINVAL;
assert_cfg80211_lock();
if (info->attrs[NL80211_ATTR_WIPHY]) {
bywiphyidx = cfg80211_rdev_by_wiphy_idx(
nla_get_u32(info->attrs[NL80211_ATTR_WIPHY]));
err = -ENODEV;
}
if (info->attrs[NL80211_ATTR_IFINDEX]) {
ifindex = nla_get_u32(info->attrs[NL80211_ATTR_IFINDEX]);
dev = dev_get_by_index(genl_info_net(info), ifindex);
if (dev) {
if (dev->ieee80211_ptr)
byifidx =
wiphy_to_dev(dev->ieee80211_ptr->wiphy);
dev_put(dev);
}
err = -ENODEV;
}
if (bywiphyidx && byifidx) {
if (bywiphyidx != byifidx)
return ERR_PTR(-EINVAL);
else
return bywiphyidx; /* == byifidx */
}
if (bywiphyidx)
return bywiphyidx;
if (byifidx)
return byifidx;
return ERR_PTR(err);
}
struct cfg80211_registered_device *
cfg80211_get_dev_from_info(struct genl_info *info)
{
struct cfg80211_registered_device *rdev;
mutex_lock(&cfg80211_mutex);
rdev = __cfg80211_rdev_from_info(info);
/* if it is not an error we grab the lock on
* it to assure it won't be going away while
* we operate on it */
if (!IS_ERR(rdev))
mutex_lock(&rdev->mtx);
mutex_unlock(&cfg80211_mutex);
return rdev;
}
struct cfg80211_registered_device *
cfg80211_get_dev_from_ifindex(struct net *net, int ifindex)
{
struct cfg80211_registered_device *rdev = ERR_PTR(-ENODEV);
struct net_device *dev;
mutex_lock(&cfg80211_mutex);
dev = dev_get_by_index(net, ifindex);
if (!dev)
goto out;
if (dev->ieee80211_ptr) {
rdev = wiphy_to_dev(dev->ieee80211_ptr->wiphy);
mutex_lock(&rdev->mtx);
} else
rdev = ERR_PTR(-ENODEV);
dev_put(dev);
out:
mutex_unlock(&cfg80211_mutex);
return rdev;
}
/* requires cfg80211_mutex to be held */
int cfg80211_dev_rename(struct cfg80211_registered_device *rdev,
char *newname)
{
struct cfg80211_registered_device *rdev2;
int wiphy_idx, taken = -1, result, digits;
assert_cfg80211_lock();
/* prohibit calling the thing phy%d when %d is not its number */
sscanf(newname, PHY_NAME "%d%n", &wiphy_idx, &taken);
if (taken == strlen(newname) && wiphy_idx != rdev->wiphy_idx) {
/* count number of places needed to print wiphy_idx */
digits = 1;
while (wiphy_idx /= 10)
digits++;
/*
* deny the name if it is phy<idx> where <idx> is printed
* without leading zeroes. taken == strlen(newname) here
*/
if (taken == strlen(PHY_NAME) + digits)
return -EINVAL;
}
/* Ignore nop renames */
if (strcmp(newname, dev_name(&rdev->wiphy.dev)) == 0)
return 0;
/* Ensure another device does not already have this name. */
list_for_each_entry(rdev2, &cfg80211_rdev_list, list)
if (strcmp(newname, dev_name(&rdev2->wiphy.dev)) == 0)
return -EINVAL;
result = device_rename(&rdev->wiphy.dev, newname);
if (result)
return result;
if (rdev->wiphy.debugfsdir &&
!debugfs_rename(rdev->wiphy.debugfsdir->d_parent,
rdev->wiphy.debugfsdir,
rdev->wiphy.debugfsdir->d_parent,
newname))
pr_err("failed to rename debugfs dir to %s!\n", newname);
nl80211_notify_dev_rename(rdev);
return 0;
}
int cfg80211_switch_netns(struct cfg80211_registered_device *rdev,
struct net *net)
{
struct wireless_dev *wdev;
int err = 0;
if (!(rdev->wiphy.flags & WIPHY_FLAG_NETNS_OK))
return -EOPNOTSUPP;
list_for_each_entry(wdev, &rdev->netdev_list, list) {
wdev->netdev->features &= ~NETIF_F_NETNS_LOCAL;
err = dev_change_net_namespace(wdev->netdev, net, "wlan%d");
if (err)
break;
wdev->netdev->features |= NETIF_F_NETNS_LOCAL;
}
if (err) {
/* failed -- clean up to old netns */
net = wiphy_net(&rdev->wiphy);
list_for_each_entry_continue_reverse(wdev, &rdev->netdev_list,
list) {
wdev->netdev->features &= ~NETIF_F_NETNS_LOCAL;
err = dev_change_net_namespace(wdev->netdev, net,
"wlan%d");
WARN_ON(err);
wdev->netdev->features |= NETIF_F_NETNS_LOCAL;
}
return err;
}
wiphy_net_set(&rdev->wiphy, net);
err = device_rename(&rdev->wiphy.dev, dev_name(&rdev->wiphy.dev));
WARN_ON(err);
return 0;
}
static void cfg80211_rfkill_poll(struct rfkill *rfkill, void *data)
{
struct cfg80211_registered_device *rdev = data;
rdev->ops->rfkill_poll(&rdev->wiphy);
}
static int cfg80211_rfkill_set_block(void *data, bool blocked)
{
struct cfg80211_registered_device *rdev = data;
struct wireless_dev *wdev;
if (!blocked)
return 0;
rtnl_lock();
mutex_lock(&rdev->devlist_mtx);
list_for_each_entry(wdev, &rdev->netdev_list, list)
dev_close(wdev->netdev);
mutex_unlock(&rdev->devlist_mtx);
rtnl_unlock();
return 0;
}
static void cfg80211_rfkill_sync_work(struct work_struct *work)
{
struct cfg80211_registered_device *rdev;
rdev = container_of(work, struct cfg80211_registered_device, rfkill_sync);
cfg80211_rfkill_set_block(rdev, rfkill_blocked(rdev->rfkill));
}
static void cfg80211_event_work(struct work_struct *work)
{
struct cfg80211_registered_device *rdev;
rdev = container_of(work, struct cfg80211_registered_device,
event_work);
rtnl_lock();
cfg80211_lock_rdev(rdev);
cfg80211_process_rdev_events(rdev);
cfg80211_unlock_rdev(rdev);
rtnl_unlock();
}
/* exported functions */
struct wiphy *wiphy_new(const struct cfg80211_ops *ops, int sizeof_priv)
{
static int wiphy_counter;
struct cfg80211_registered_device *rdev;
int alloc_size;
WARN_ON(ops->add_key && (!ops->del_key || !ops->set_default_key));
WARN_ON(ops->auth && (!ops->assoc || !ops->deauth || !ops->disassoc));
WARN_ON(ops->connect && !ops->disconnect);
WARN_ON(ops->join_ibss && !ops->leave_ibss);
WARN_ON(ops->add_virtual_intf && !ops->del_virtual_intf);
WARN_ON(ops->add_station && !ops->del_station);
WARN_ON(ops->add_mpath && !ops->del_mpath);
WARN_ON(ops->join_mesh && !ops->leave_mesh);
alloc_size = sizeof(*rdev) + sizeof_priv;
rdev = kzalloc(alloc_size, GFP_KERNEL);
if (!rdev)
return NULL;
rdev->ops = ops;
mutex_lock(&cfg80211_mutex);
rdev->wiphy_idx = wiphy_counter++;
if (unlikely(!wiphy_idx_valid(rdev->wiphy_idx))) {
wiphy_counter--;
mutex_unlock(&cfg80211_mutex);
/* ugh, wrapped! */
kfree(rdev);
return NULL;
}
mutex_unlock(&cfg80211_mutex);
/* give it a proper name */
dev_set_name(&rdev->wiphy.dev, PHY_NAME "%d", rdev->wiphy_idx);
mutex_init(&rdev->mtx);
mutex_init(&rdev->devlist_mtx);
INIT_LIST_HEAD(&rdev->netdev_list);
spin_lock_init(&rdev->bss_lock);
INIT_LIST_HEAD(&rdev->bss_list);
INIT_WORK(&rdev->scan_done_wk, __cfg80211_scan_done);
#ifdef CONFIG_CFG80211_WEXT
rdev->wiphy.wext = &cfg80211_wext_handler;
#endif
device_initialize(&rdev->wiphy.dev);
rdev->wiphy.dev.class = &ieee80211_class;
rdev->wiphy.dev.platform_data = rdev;
#ifdef CONFIG_CFG80211_DEFAULT_PS
rdev->wiphy.flags |= WIPHY_FLAG_PS_ON_BY_DEFAULT;
#endif
wiphy_net_set(&rdev->wiphy, &init_net);
rdev->rfkill_ops.set_block = cfg80211_rfkill_set_block;
rdev->rfkill = rfkill_alloc(dev_name(&rdev->wiphy.dev),
&rdev->wiphy.dev, RFKILL_TYPE_WLAN,
&rdev->rfkill_ops, rdev);
if (!rdev->rfkill) {
kfree(rdev);
return NULL;
}
INIT_WORK(&rdev->rfkill_sync, cfg80211_rfkill_sync_work);
INIT_WORK(&rdev->conn_work, cfg80211_conn_work);
INIT_WORK(&rdev->event_work, cfg80211_event_work);
init_waitqueue_head(&rdev->dev_wait);
/*
* Initialize wiphy parameters to IEEE 802.11 MIB default values.
* Fragmentation and RTS threshold are disabled by default with the
* special -1 value.
*/
rdev->wiphy.retry_short = 7;
rdev->wiphy.retry_long = 4;
rdev->wiphy.frag_threshold = (u32) -1;
rdev->wiphy.rts_threshold = (u32) -1;
rdev->wiphy.coverage_class = 0;
return &rdev->wiphy;
}
EXPORT_SYMBOL(wiphy_new);
int wiphy_register(struct wiphy *wiphy)
{
struct cfg80211_registered_device *rdev = wiphy_to_dev(wiphy);
int res;
enum ieee80211_band band;
struct ieee80211_supported_band *sband;
bool have_band = false;
int i;
u16 ifmodes = wiphy->interface_modes;
if (WARN_ON(wiphy->addresses && !wiphy->n_addresses))
return -EINVAL;
if (WARN_ON(wiphy->addresses &&
!is_zero_ether_addr(wiphy->perm_addr) &&
memcmp(wiphy->perm_addr, wiphy->addresses[0].addr,
ETH_ALEN)))
return -EINVAL;
if (wiphy->addresses)
memcpy(wiphy->perm_addr, wiphy->addresses[0].addr, ETH_ALEN);
/* sanity check ifmodes */
WARN_ON(!ifmodes);
ifmodes &= ((1 << NUM_NL80211_IFTYPES) - 1) & ~1;
if (WARN_ON(ifmodes != wiphy->interface_modes))
wiphy->interface_modes = ifmodes;
/* sanity check supported bands/channels */
for (band = 0; band < IEEE80211_NUM_BANDS; band++) {
sband = wiphy->bands[band];
if (!sband)
continue;
sband->band = band;
if (WARN_ON(!sband->n_channels || !sband->n_bitrates))
return -EINVAL;
/*
* Since we use a u32 for rate bitmaps in
* ieee80211_get_response_rate, we cannot
* have more than 32 legacy rates.
*/
if (WARN_ON(sband->n_bitrates > 32))
return -EINVAL;
for (i = 0; i < sband->n_channels; i++) {
sband->channels[i].orig_flags =
sband->channels[i].flags;
sband->channels[i].orig_mag =
sband->channels[i].max_antenna_gain;
sband->channels[i].orig_mpwr =
sband->channels[i].max_power;
sband->channels[i].band = band;
}
have_band = true;
}
if (!have_band) {
WARN_ON(1);
return -EINVAL;
}
/* check and set up bitrates */
ieee80211_set_bitrate_flags(wiphy);
mutex_lock(&cfg80211_mutex);
res = device_add(&rdev->wiphy.dev);
wireless: register wiphy rfkill w/o holding cfg80211_mutex Otherwise lockdep complains... https://bugzilla.kernel.org/show_bug.cgi?id=17311 [ INFO: possible circular locking dependency detected ] 2.6.36-rc2-git4 #12 ------------------------------------------------------- kworker/0:3/3630 is trying to acquire lock: (rtnl_mutex){+.+.+.}, at: [<ffffffff813396c7>] rtnl_lock+0x12/0x14 but task is already holding lock: (rfkill_global_mutex){+.+.+.}, at: [<ffffffffa014b129>] rfkill_switch_all+0x24/0x49 [rfkill] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (rfkill_global_mutex){+.+.+.}: [<ffffffff81079ad7>] lock_acquire+0x120/0x15b [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39 [<ffffffffa014b4ab>] rfkill_register+0x2b/0x29c [rfkill] [<ffffffffa0185ba0>] wiphy_register+0x1ae/0x270 [cfg80211] [<ffffffffa0206f01>] ieee80211_register_hw+0x1b4/0x3cf [mac80211] [<ffffffffa0292e98>] iwl_ucode_callback+0x9e9/0xae3 [iwlagn] [<ffffffff812d3e9d>] request_firmware_work_func+0x54/0x6f [<ffffffff81065d15>] kthread+0x8c/0x94 [<ffffffff8100ac24>] kernel_thread_helper+0x4/0x10 -> #1 (cfg80211_mutex){+.+.+.}: [<ffffffff81079ad7>] lock_acquire+0x120/0x15b [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39 [<ffffffffa018605e>] cfg80211_get_dev_from_ifindex+0x1b/0x7c [cfg80211] [<ffffffffa0189f36>] cfg80211_wext_giwscan+0x58/0x990 [cfg80211] [<ffffffff8139a3ce>] ioctl_standard_iw_point+0x1a8/0x272 [<ffffffff8139a529>] ioctl_standard_call+0x91/0xa7 [<ffffffff8139a687>] T.723+0xbd/0x12c [<ffffffff8139a727>] wext_handle_ioctl+0x31/0x6d [<ffffffff8133014e>] dev_ioctl+0x63d/0x67a [<ffffffff8131afd9>] sock_ioctl+0x48/0x21d [<ffffffff81102abd>] do_vfs_ioctl+0x4ba/0x509 [<ffffffff81102b5d>] sys_ioctl+0x51/0x74 [<ffffffff81009e02>] system_call_fastpath+0x16/0x1b -> #0 (rtnl_mutex){+.+.+.}: [<ffffffff810796b0>] __lock_acquire+0xa93/0xd9a [<ffffffff81079ad7>] lock_acquire+0x120/0x15b [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39 [<ffffffff813396c7>] rtnl_lock+0x12/0x14 [<ffffffffa0185cb5>] cfg80211_rfkill_set_block+0x1a/0x7b [cfg80211] [<ffffffffa014aed0>] rfkill_set_block+0x80/0xd5 [rfkill] [<ffffffffa014b07e>] __rfkill_switch_all+0x3f/0x6f [rfkill] [<ffffffffa014b13d>] rfkill_switch_all+0x38/0x49 [rfkill] [<ffffffffa014b821>] rfkill_op_handler+0x105/0x136 [rfkill] [<ffffffff81060708>] process_one_work+0x248/0x403 [<ffffffff81062620>] worker_thread+0x139/0x214 [<ffffffff81065d15>] kthread+0x8c/0x94 [<ffffffff8100ac24>] kernel_thread_helper+0x4/0x10 Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Johannes Berg <johannes@sipsolutions.net>
2010-08-31 05:36:40 +08:00
if (res) {
mutex_unlock(&cfg80211_mutex);
return res;
}
/* set up regulatory info */
wiphy_update_regulatory(wiphy, NL80211_REGDOM_SET_BY_CORE);
list_add_rcu(&rdev->list, &cfg80211_rdev_list);
cfg80211_rdev_list_generation++;
/* add to debugfs */
rdev->wiphy.debugfsdir =
debugfs_create_dir(wiphy_name(&rdev->wiphy),
ieee80211_debugfs_dir);
if (IS_ERR(rdev->wiphy.debugfsdir))
rdev->wiphy.debugfsdir = NULL;
if (wiphy->flags & WIPHY_FLAG_CUSTOM_REGULATORY) {
struct regulatory_request request;
request.wiphy_idx = get_wiphy_idx(wiphy);
request.initiator = NL80211_REGDOM_SET_BY_DRIVER;
request.alpha2[0] = '9';
request.alpha2[1] = '9';
nl80211_send_reg_change_event(&request);
}
cfg80211_debugfs_rdev_add(rdev);
mutex_unlock(&cfg80211_mutex);
wireless: register wiphy rfkill w/o holding cfg80211_mutex Otherwise lockdep complains... https://bugzilla.kernel.org/show_bug.cgi?id=17311 [ INFO: possible circular locking dependency detected ] 2.6.36-rc2-git4 #12 ------------------------------------------------------- kworker/0:3/3630 is trying to acquire lock: (rtnl_mutex){+.+.+.}, at: [<ffffffff813396c7>] rtnl_lock+0x12/0x14 but task is already holding lock: (rfkill_global_mutex){+.+.+.}, at: [<ffffffffa014b129>] rfkill_switch_all+0x24/0x49 [rfkill] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (rfkill_global_mutex){+.+.+.}: [<ffffffff81079ad7>] lock_acquire+0x120/0x15b [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39 [<ffffffffa014b4ab>] rfkill_register+0x2b/0x29c [rfkill] [<ffffffffa0185ba0>] wiphy_register+0x1ae/0x270 [cfg80211] [<ffffffffa0206f01>] ieee80211_register_hw+0x1b4/0x3cf [mac80211] [<ffffffffa0292e98>] iwl_ucode_callback+0x9e9/0xae3 [iwlagn] [<ffffffff812d3e9d>] request_firmware_work_func+0x54/0x6f [<ffffffff81065d15>] kthread+0x8c/0x94 [<ffffffff8100ac24>] kernel_thread_helper+0x4/0x10 -> #1 (cfg80211_mutex){+.+.+.}: [<ffffffff81079ad7>] lock_acquire+0x120/0x15b [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39 [<ffffffffa018605e>] cfg80211_get_dev_from_ifindex+0x1b/0x7c [cfg80211] [<ffffffffa0189f36>] cfg80211_wext_giwscan+0x58/0x990 [cfg80211] [<ffffffff8139a3ce>] ioctl_standard_iw_point+0x1a8/0x272 [<ffffffff8139a529>] ioctl_standard_call+0x91/0xa7 [<ffffffff8139a687>] T.723+0xbd/0x12c [<ffffffff8139a727>] wext_handle_ioctl+0x31/0x6d [<ffffffff8133014e>] dev_ioctl+0x63d/0x67a [<ffffffff8131afd9>] sock_ioctl+0x48/0x21d [<ffffffff81102abd>] do_vfs_ioctl+0x4ba/0x509 [<ffffffff81102b5d>] sys_ioctl+0x51/0x74 [<ffffffff81009e02>] system_call_fastpath+0x16/0x1b -> #0 (rtnl_mutex){+.+.+.}: [<ffffffff810796b0>] __lock_acquire+0xa93/0xd9a [<ffffffff81079ad7>] lock_acquire+0x120/0x15b [<ffffffff813ae869>] __mutex_lock_common+0x54/0x52e [<ffffffff813aede9>] mutex_lock_nested+0x34/0x39 [<ffffffff813396c7>] rtnl_lock+0x12/0x14 [<ffffffffa0185cb5>] cfg80211_rfkill_set_block+0x1a/0x7b [cfg80211] [<ffffffffa014aed0>] rfkill_set_block+0x80/0xd5 [rfkill] [<ffffffffa014b07e>] __rfkill_switch_all+0x3f/0x6f [rfkill] [<ffffffffa014b13d>] rfkill_switch_all+0x38/0x49 [rfkill] [<ffffffffa014b821>] rfkill_op_handler+0x105/0x136 [rfkill] [<ffffffff81060708>] process_one_work+0x248/0x403 [<ffffffff81062620>] worker_thread+0x139/0x214 [<ffffffff81065d15>] kthread+0x8c/0x94 [<ffffffff8100ac24>] kernel_thread_helper+0x4/0x10 Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Johannes Berg <johannes@sipsolutions.net>
2010-08-31 05:36:40 +08:00
/*
* due to a locking dependency this has to be outside of the
* cfg80211_mutex lock
*/
res = rfkill_register(rdev->rfkill);
if (res)
goto out_rm_dev;
return 0;
out_rm_dev:
device_del(&rdev->wiphy.dev);
return res;
}
EXPORT_SYMBOL(wiphy_register);
void wiphy_rfkill_start_polling(struct wiphy *wiphy)
{
struct cfg80211_registered_device *rdev = wiphy_to_dev(wiphy);
if (!rdev->ops->rfkill_poll)
return;
rdev->rfkill_ops.poll = cfg80211_rfkill_poll;
rfkill_resume_polling(rdev->rfkill);
}
EXPORT_SYMBOL(wiphy_rfkill_start_polling);
void wiphy_rfkill_stop_polling(struct wiphy *wiphy)
{
struct cfg80211_registered_device *rdev = wiphy_to_dev(wiphy);
rfkill_pause_polling(rdev->rfkill);
}
EXPORT_SYMBOL(wiphy_rfkill_stop_polling);
void wiphy_unregister(struct wiphy *wiphy)
{
struct cfg80211_registered_device *rdev = wiphy_to_dev(wiphy);
rfkill_unregister(rdev->rfkill);
/* protect the device list */
mutex_lock(&cfg80211_mutex);
wait_event(rdev->dev_wait, ({
int __count;
mutex_lock(&rdev->devlist_mtx);
__count = rdev->opencount;
mutex_unlock(&rdev->devlist_mtx);
__count == 0;}));
mutex_lock(&rdev->devlist_mtx);
BUG_ON(!list_empty(&rdev->netdev_list));
mutex_unlock(&rdev->devlist_mtx);
/*
* First remove the hardware from everywhere, this makes
* it impossible to find from userspace.
*/
debugfs_remove_recursive(rdev->wiphy.debugfsdir);
list_del_rcu(&rdev->list);
synchronize_rcu();
/*
* Try to grab rdev->mtx. If a command is still in progress,
* hopefully the driver will refuse it since it's tearing
* down the device already. We wait for this command to complete
* before unlinking the item from the list.
* Note: as codified by the BUG_ON above we cannot get here if
* a virtual interface is still present. Hence, we can only get
* to lock contention here if userspace issues a command that
* identified the hardware by wiphy index.
*/
cfg80211_lock_rdev(rdev);
/* nothing */
cfg80211_unlock_rdev(rdev);
/* If this device got a regulatory hint tell core its
* free to listen now to a new shiny device regulatory hint */
reg_device_remove(wiphy);
cfg80211_rdev_list_generation++;
device_del(&rdev->wiphy.dev);
mutex_unlock(&cfg80211_mutex);
flush_work(&rdev->scan_done_wk);
cancel_work_sync(&rdev->conn_work);
flush_work(&rdev->event_work);
}
EXPORT_SYMBOL(wiphy_unregister);
void cfg80211_dev_free(struct cfg80211_registered_device *rdev)
{
struct cfg80211_internal_bss *scan, *tmp;
rfkill_destroy(rdev->rfkill);
mutex_destroy(&rdev->mtx);
mutex_destroy(&rdev->devlist_mtx);
list_for_each_entry_safe(scan, tmp, &rdev->bss_list, list)
cfg80211_put_bss(&scan->pub);
kfree(rdev);
}
void wiphy_free(struct wiphy *wiphy)
{
put_device(&wiphy->dev);
}
EXPORT_SYMBOL(wiphy_free);
void wiphy_rfkill_set_hw_state(struct wiphy *wiphy, bool blocked)
{
struct cfg80211_registered_device *rdev = wiphy_to_dev(wiphy);
if (rfkill_set_hw_state(rdev->rfkill, blocked))
schedule_work(&rdev->rfkill_sync);
}
EXPORT_SYMBOL(wiphy_rfkill_set_hw_state);
static void wdev_cleanup_work(struct work_struct *work)
{
struct wireless_dev *wdev;
struct cfg80211_registered_device *rdev;
wdev = container_of(work, struct wireless_dev, cleanup_work);
rdev = wiphy_to_dev(wdev->wiphy);
cfg80211_lock_rdev(rdev);
if (WARN_ON(rdev->scan_req && rdev->scan_req->dev == wdev->netdev)) {
rdev->scan_req->aborted = true;
___cfg80211_scan_done(rdev, true);
}
cfg80211_unlock_rdev(rdev);
mutex_lock(&rdev->devlist_mtx);
rdev->opencount--;
mutex_unlock(&rdev->devlist_mtx);
wake_up(&rdev->dev_wait);
dev_put(wdev->netdev);
}
static struct device_type wiphy_type = {
.name = "wlan",
};
static int cfg80211_netdev_notifier_call(struct notifier_block * nb,
unsigned long state,
void *ndev)
{
struct net_device *dev = ndev;
struct wireless_dev *wdev = dev->ieee80211_ptr;
struct cfg80211_registered_device *rdev;
if (!wdev)
return NOTIFY_DONE;
rdev = wiphy_to_dev(wdev->wiphy);
WARN_ON(wdev->iftype == NL80211_IFTYPE_UNSPECIFIED);
switch (state) {
case NETDEV_POST_INIT:
SET_NETDEV_DEVTYPE(dev, &wiphy_type);
break;
case NETDEV_REGISTER:
/*
* NB: cannot take rdev->mtx here because this may be
* called within code protected by it when interfaces
* are added with nl80211.
*/
mutex_init(&wdev->mtx);
INIT_WORK(&wdev->cleanup_work, wdev_cleanup_work);
INIT_LIST_HEAD(&wdev->event_list);
spin_lock_init(&wdev->event_lock);
INIT_LIST_HEAD(&wdev->mgmt_registrations);
spin_lock_init(&wdev->mgmt_registrations_lock);
mutex_lock(&rdev->devlist_mtx);
list_add_rcu(&wdev->list, &rdev->netdev_list);
rdev->devlist_generation++;
/* can only change netns with wiphy */
dev->features |= NETIF_F_NETNS_LOCAL;
if (sysfs_create_link(&dev->dev.kobj, &rdev->wiphy.dev.kobj,
"phy80211")) {
pr_err("failed to add phy80211 symlink to netdev!\n");
}
wdev->netdev = dev;
wdev->sme_state = CFG80211_SME_IDLE;
mutex_unlock(&rdev->devlist_mtx);
#ifdef CONFIG_CFG80211_WEXT
wdev->wext.default_key = -1;
wdev->wext.default_mgmt_key = -1;
wdev->wext.connect.auth_type = NL80211_AUTHTYPE_AUTOMATIC;
nl80211: add power save commands The most needed command from nl80211, which Wireless Extensions had, is support for power save mode. Add a simple command to make it possible to enable and disable power save via nl80211. I was also planning about extending the interface, for example adding the timeout value, but after thinking more about this I decided not to do it. Basically there were three reasons: Firstly, the parameters for power save are very much hardware dependent. Trying to find a unified interface which would work with all hardware, and still make sense to users, will be very difficult. Secondly, IEEE 802.11 power save implementation in Linux is still in state of flux. We have a long way to still to go and there is no way to predict what kind of implementation we will have after few years. And because we need to support nl80211 interface a long time, practically forever, adding now parameters to nl80211 might create maintenance problems later on. Third issue are the users. Power save parameters are mostly used for debugging, so debugfs is better, more flexible, interface for this. For example, wpa_supplicant currently doesn't configure anything related to power save mode. It's better to strive that kernel can automatically optimise the power save parameters, like with help of pm qos network and other traffic parameters. Later on, when we have better understanding of power save, we can extend this command with more features, if there's a need for that. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-02-17 23:58:10 +08:00
#endif
if (wdev->wiphy->flags & WIPHY_FLAG_PS_ON_BY_DEFAULT)
nl80211: add power save commands The most needed command from nl80211, which Wireless Extensions had, is support for power save mode. Add a simple command to make it possible to enable and disable power save via nl80211. I was also planning about extending the interface, for example adding the timeout value, but after thinking more about this I decided not to do it. Basically there were three reasons: Firstly, the parameters for power save are very much hardware dependent. Trying to find a unified interface which would work with all hardware, and still make sense to users, will be very difficult. Secondly, IEEE 802.11 power save implementation in Linux is still in state of flux. We have a long way to still to go and there is no way to predict what kind of implementation we will have after few years. And because we need to support nl80211 interface a long time, practically forever, adding now parameters to nl80211 might create maintenance problems later on. Third issue are the users. Power save parameters are mostly used for debugging, so debugfs is better, more flexible, interface for this. For example, wpa_supplicant currently doesn't configure anything related to power save mode. It's better to strive that kernel can automatically optimise the power save parameters, like with help of pm qos network and other traffic parameters. Later on, when we have better understanding of power save, we can extend this command with more features, if there's a need for that. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-02-17 23:58:10 +08:00
wdev->ps = true;
else
nl80211: add power save commands The most needed command from nl80211, which Wireless Extensions had, is support for power save mode. Add a simple command to make it possible to enable and disable power save via nl80211. I was also planning about extending the interface, for example adding the timeout value, but after thinking more about this I decided not to do it. Basically there were three reasons: Firstly, the parameters for power save are very much hardware dependent. Trying to find a unified interface which would work with all hardware, and still make sense to users, will be very difficult. Secondly, IEEE 802.11 power save implementation in Linux is still in state of flux. We have a long way to still to go and there is no way to predict what kind of implementation we will have after few years. And because we need to support nl80211 interface a long time, practically forever, adding now parameters to nl80211 might create maintenance problems later on. Third issue are the users. Power save parameters are mostly used for debugging, so debugfs is better, more flexible, interface for this. For example, wpa_supplicant currently doesn't configure anything related to power save mode. It's better to strive that kernel can automatically optimise the power save parameters, like with help of pm qos network and other traffic parameters. Later on, when we have better understanding of power save, we can extend this command with more features, if there's a need for that. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-02-17 23:58:10 +08:00
wdev->ps = false;
/* allow mac80211 to determine the timeout */
wdev->ps_timeout = -1;
if (rdev->ops->set_power_mgmt)
if (rdev->ops->set_power_mgmt(wdev->wiphy, dev,
nl80211: add power save commands The most needed command from nl80211, which Wireless Extensions had, is support for power save mode. Add a simple command to make it possible to enable and disable power save via nl80211. I was also planning about extending the interface, for example adding the timeout value, but after thinking more about this I decided not to do it. Basically there were three reasons: Firstly, the parameters for power save are very much hardware dependent. Trying to find a unified interface which would work with all hardware, and still make sense to users, will be very difficult. Secondly, IEEE 802.11 power save implementation in Linux is still in state of flux. We have a long way to still to go and there is no way to predict what kind of implementation we will have after few years. And because we need to support nl80211 interface a long time, practically forever, adding now parameters to nl80211 might create maintenance problems later on. Third issue are the users. Power save parameters are mostly used for debugging, so debugfs is better, more flexible, interface for this. For example, wpa_supplicant currently doesn't configure anything related to power save mode. It's better to strive that kernel can automatically optimise the power save parameters, like with help of pm qos network and other traffic parameters. Later on, when we have better understanding of power save, we can extend this command with more features, if there's a need for that. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-02-17 23:58:10 +08:00
wdev->ps,
wdev->ps_timeout)) {
/* assume this means it's off */
nl80211: add power save commands The most needed command from nl80211, which Wireless Extensions had, is support for power save mode. Add a simple command to make it possible to enable and disable power save via nl80211. I was also planning about extending the interface, for example adding the timeout value, but after thinking more about this I decided not to do it. Basically there were three reasons: Firstly, the parameters for power save are very much hardware dependent. Trying to find a unified interface which would work with all hardware, and still make sense to users, will be very difficult. Secondly, IEEE 802.11 power save implementation in Linux is still in state of flux. We have a long way to still to go and there is no way to predict what kind of implementation we will have after few years. And because we need to support nl80211 interface a long time, practically forever, adding now parameters to nl80211 might create maintenance problems later on. Third issue are the users. Power save parameters are mostly used for debugging, so debugfs is better, more flexible, interface for this. For example, wpa_supplicant currently doesn't configure anything related to power save mode. It's better to strive that kernel can automatically optimise the power save parameters, like with help of pm qos network and other traffic parameters. Later on, when we have better understanding of power save, we can extend this command with more features, if there's a need for that. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-02-17 23:58:10 +08:00
wdev->ps = false;
}
nl80211: add power save commands The most needed command from nl80211, which Wireless Extensions had, is support for power save mode. Add a simple command to make it possible to enable and disable power save via nl80211. I was also planning about extending the interface, for example adding the timeout value, but after thinking more about this I decided not to do it. Basically there were three reasons: Firstly, the parameters for power save are very much hardware dependent. Trying to find a unified interface which would work with all hardware, and still make sense to users, will be very difficult. Secondly, IEEE 802.11 power save implementation in Linux is still in state of flux. We have a long way to still to go and there is no way to predict what kind of implementation we will have after few years. And because we need to support nl80211 interface a long time, practically forever, adding now parameters to nl80211 might create maintenance problems later on. Third issue are the users. Power save parameters are mostly used for debugging, so debugfs is better, more flexible, interface for this. For example, wpa_supplicant currently doesn't configure anything related to power save mode. It's better to strive that kernel can automatically optimise the power save parameters, like with help of pm qos network and other traffic parameters. Later on, when we have better understanding of power save, we can extend this command with more features, if there's a need for that. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-02-17 23:58:10 +08:00
if (!dev->ethtool_ops)
dev->ethtool_ops = &cfg80211_ethtool_ops;
if ((wdev->iftype == NL80211_IFTYPE_STATION ||
wdev->iftype == NL80211_IFTYPE_P2P_CLIENT ||
wdev->iftype == NL80211_IFTYPE_ADHOC) && !wdev->use_4addr)
dev->priv_flags |= IFF_DONT_BRIDGE;
break;
case NETDEV_GOING_DOWN:
switch (wdev->iftype) {
case NL80211_IFTYPE_ADHOC:
cfg80211_leave_ibss(rdev, dev, true);
break;
case NL80211_IFTYPE_P2P_CLIENT:
case NL80211_IFTYPE_STATION:
wdev_lock(wdev);
#ifdef CONFIG_CFG80211_WEXT
kfree(wdev->wext.ie);
wdev->wext.ie = NULL;
wdev->wext.ie_len = 0;
wdev->wext.connect.auth_type = NL80211_AUTHTYPE_AUTOMATIC;
#endif
__cfg80211_disconnect(rdev, dev,
WLAN_REASON_DEAUTH_LEAVING, true);
cfg80211_mlme_down(rdev, dev);
wdev_unlock(wdev);
break;
case NL80211_IFTYPE_MESH_POINT:
cfg80211_leave_mesh(rdev, dev);
break;
default:
break;
}
break;
case NETDEV_DOWN:
dev_hold(dev);
queue_work(cfg80211_wq, &wdev->cleanup_work);
break;
case NETDEV_UP:
/*
* If we have a really quick DOWN/UP succession we may
* have this work still pending ... cancel it and see
* if it was pending, in which case we need to account
* for some of the work it would have done.
*/
if (cancel_work_sync(&wdev->cleanup_work)) {
mutex_lock(&rdev->devlist_mtx);
rdev->opencount--;
mutex_unlock(&rdev->devlist_mtx);
dev_put(dev);
}
cfg80211_lock_rdev(rdev);
mutex_lock(&rdev->devlist_mtx);
wdev_lock(wdev);
switch (wdev->iftype) {
#ifdef CONFIG_CFG80211_WEXT
case NL80211_IFTYPE_ADHOC:
cfg80211_ibss_wext_join(rdev, wdev);
break;
case NL80211_IFTYPE_STATION:
cfg80211_mgd_wext_connect(rdev, wdev);
break;
#endif
#ifdef CONFIG_MAC80211_MESH
case NL80211_IFTYPE_MESH_POINT:
{
/* backward compat code... */
struct mesh_setup setup;
memcpy(&setup, &default_mesh_setup,
sizeof(setup));
/* back compat only needed for mesh_id */
setup.mesh_id = wdev->ssid;
setup.mesh_id_len = wdev->mesh_id_up_len;
if (wdev->mesh_id_up_len)
__cfg80211_join_mesh(rdev, dev,
&setup,
&default_mesh_config);
break;
}
#endif
default:
break;
}
wdev_unlock(wdev);
rdev->opencount++;
mutex_unlock(&rdev->devlist_mtx);
cfg80211_unlock_rdev(rdev);
break;
case NETDEV_UNREGISTER:
/*
* NB: cannot take rdev->mtx here because this may be
* called within code protected by it when interfaces
* are removed with nl80211.
*/
mutex_lock(&rdev->devlist_mtx);
/*
* It is possible to get NETDEV_UNREGISTER
* multiple times. To detect that, check
* that the interface is still on the list
* of registered interfaces, and only then
* remove and clean it up.
*/
if (!list_empty(&wdev->list)) {
sysfs_remove_link(&dev->dev.kobj, "phy80211");
list_del_rcu(&wdev->list);
rdev->devlist_generation++;
cfg80211_mlme_purge_registrations(wdev);
#ifdef CONFIG_CFG80211_WEXT
kfree(wdev->wext.keys);
#endif
}
mutex_unlock(&rdev->devlist_mtx);
/*
* synchronise (so that we won't find this netdev
* from other code any more) and then clear the list
* head so that the above code can safely check for
* !list_empty() to avoid double-cleanup.
*/
synchronize_rcu();
INIT_LIST_HEAD(&wdev->list);
break;
case NETDEV_PRE_UP:
if (!(wdev->wiphy->interface_modes & BIT(wdev->iftype)))
return notifier_from_errno(-EOPNOTSUPP);
if (rfkill_blocked(rdev->rfkill))
return notifier_from_errno(-ERFKILL);
break;
}
return NOTIFY_DONE;
}
static struct notifier_block cfg80211_netdev_notifier = {
.notifier_call = cfg80211_netdev_notifier_call,
};
static void __net_exit cfg80211_pernet_exit(struct net *net)
{
struct cfg80211_registered_device *rdev;
rtnl_lock();
mutex_lock(&cfg80211_mutex);
list_for_each_entry(rdev, &cfg80211_rdev_list, list) {
if (net_eq(wiphy_net(&rdev->wiphy), net))
WARN_ON(cfg80211_switch_netns(rdev, &init_net));
}
mutex_unlock(&cfg80211_mutex);
rtnl_unlock();
}
static struct pernet_operations cfg80211_pernet_ops = {
.exit = cfg80211_pernet_exit,
};
static int __init cfg80211_init(void)
{
cfg80211: Add new wireless regulatory infrastructure This adds the new wireless regulatory infrastructure. The main motiviation behind this was to centralize regulatory code as each driver was implementing their own regulatory solution, and to replace the initial centralized code we have where: * only 3 regulatory domains are supported: US, JP and EU * regulatory domains can only be changed through module parameter * all rules were built statically in the kernel We now have support for regulatory domains for many countries and regulatory domains are now queried through a userspace agent through udev allowing distributions to update regulatory rules without updating the kernel. Each driver can regulatory_hint() a regulatory domain based on either their EEPROM mapped regulatory domain value to a respective ISO/IEC 3166-1 country code or pass an internally built regulatory domain. We also add support to let the user set the regulatory domain through userspace in case of faulty EEPROMs to further help compliance. Support for world roaming will be added soon for cards capable of this. For more information see: http://wireless.kernel.org/en/developers/Regulatory/CRDA For now we leave an option to enable the old module parameter, ieee80211_regdom, and to build the 3 old regdomains statically (US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY. These old static definitions and the module parameter is being scheduled for removal for 2.6.29. Note that if you use this you won't make use of a world regulatory domain as its pointless. If you leave this option enabled and if CRDA is present and you use US or JP we will try to ask CRDA to update us a regulatory domain for us. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-10 14:19:48 +08:00
int err;
err = register_pernet_device(&cfg80211_pernet_ops);
if (err)
goto out_fail_pernet;
cfg80211: Add new wireless regulatory infrastructure This adds the new wireless regulatory infrastructure. The main motiviation behind this was to centralize regulatory code as each driver was implementing their own regulatory solution, and to replace the initial centralized code we have where: * only 3 regulatory domains are supported: US, JP and EU * regulatory domains can only be changed through module parameter * all rules were built statically in the kernel We now have support for regulatory domains for many countries and regulatory domains are now queried through a userspace agent through udev allowing distributions to update regulatory rules without updating the kernel. Each driver can regulatory_hint() a regulatory domain based on either their EEPROM mapped regulatory domain value to a respective ISO/IEC 3166-1 country code or pass an internally built regulatory domain. We also add support to let the user set the regulatory domain through userspace in case of faulty EEPROMs to further help compliance. Support for world roaming will be added soon for cards capable of this. For more information see: http://wireless.kernel.org/en/developers/Regulatory/CRDA For now we leave an option to enable the old module parameter, ieee80211_regdom, and to build the 3 old regdomains statically (US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY. These old static definitions and the module parameter is being scheduled for removal for 2.6.29. Note that if you use this you won't make use of a world regulatory domain as its pointless. If you leave this option enabled and if CRDA is present and you use US or JP we will try to ask CRDA to update us a regulatory domain for us. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-10 14:19:48 +08:00
err = wiphy_sysfs_init();
if (err)
goto out_fail_sysfs;
err = register_netdevice_notifier(&cfg80211_netdev_notifier);
if (err)
goto out_fail_notifier;
err = nl80211_init();
if (err)
goto out_fail_nl80211;
ieee80211_debugfs_dir = debugfs_create_dir("ieee80211", NULL);
cfg80211: Add new wireless regulatory infrastructure This adds the new wireless regulatory infrastructure. The main motiviation behind this was to centralize regulatory code as each driver was implementing their own regulatory solution, and to replace the initial centralized code we have where: * only 3 regulatory domains are supported: US, JP and EU * regulatory domains can only be changed through module parameter * all rules were built statically in the kernel We now have support for regulatory domains for many countries and regulatory domains are now queried through a userspace agent through udev allowing distributions to update regulatory rules without updating the kernel. Each driver can regulatory_hint() a regulatory domain based on either their EEPROM mapped regulatory domain value to a respective ISO/IEC 3166-1 country code or pass an internally built regulatory domain. We also add support to let the user set the regulatory domain through userspace in case of faulty EEPROMs to further help compliance. Support for world roaming will be added soon for cards capable of this. For more information see: http://wireless.kernel.org/en/developers/Regulatory/CRDA For now we leave an option to enable the old module parameter, ieee80211_regdom, and to build the 3 old regdomains statically (US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY. These old static definitions and the module parameter is being scheduled for removal for 2.6.29. Note that if you use this you won't make use of a world regulatory domain as its pointless. If you leave this option enabled and if CRDA is present and you use US or JP we will try to ask CRDA to update us a regulatory domain for us. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-10 14:19:48 +08:00
err = regulatory_init();
if (err)
goto out_fail_reg;
cfg80211_wq = create_singlethread_workqueue("cfg80211");
if (!cfg80211_wq)
goto out_fail_wq;
return 0;
out_fail_wq:
regulatory_exit();
cfg80211: Add new wireless regulatory infrastructure This adds the new wireless regulatory infrastructure. The main motiviation behind this was to centralize regulatory code as each driver was implementing their own regulatory solution, and to replace the initial centralized code we have where: * only 3 regulatory domains are supported: US, JP and EU * regulatory domains can only be changed through module parameter * all rules were built statically in the kernel We now have support for regulatory domains for many countries and regulatory domains are now queried through a userspace agent through udev allowing distributions to update regulatory rules without updating the kernel. Each driver can regulatory_hint() a regulatory domain based on either their EEPROM mapped regulatory domain value to a respective ISO/IEC 3166-1 country code or pass an internally built regulatory domain. We also add support to let the user set the regulatory domain through userspace in case of faulty EEPROMs to further help compliance. Support for world roaming will be added soon for cards capable of this. For more information see: http://wireless.kernel.org/en/developers/Regulatory/CRDA For now we leave an option to enable the old module parameter, ieee80211_regdom, and to build the 3 old regdomains statically (US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY. These old static definitions and the module parameter is being scheduled for removal for 2.6.29. Note that if you use this you won't make use of a world regulatory domain as its pointless. If you leave this option enabled and if CRDA is present and you use US or JP we will try to ask CRDA to update us a regulatory domain for us. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-10 14:19:48 +08:00
out_fail_reg:
debugfs_remove(ieee80211_debugfs_dir);
out_fail_nl80211:
unregister_netdevice_notifier(&cfg80211_netdev_notifier);
out_fail_notifier:
wiphy_sysfs_exit();
out_fail_sysfs:
unregister_pernet_device(&cfg80211_pernet_ops);
out_fail_pernet:
return err;
}
subsys_initcall(cfg80211_init);
static void __exit cfg80211_exit(void)
{
debugfs_remove(ieee80211_debugfs_dir);
nl80211_exit();
unregister_netdevice_notifier(&cfg80211_netdev_notifier);
wiphy_sysfs_exit();
cfg80211: Add new wireless regulatory infrastructure This adds the new wireless regulatory infrastructure. The main motiviation behind this was to centralize regulatory code as each driver was implementing their own regulatory solution, and to replace the initial centralized code we have where: * only 3 regulatory domains are supported: US, JP and EU * regulatory domains can only be changed through module parameter * all rules were built statically in the kernel We now have support for regulatory domains for many countries and regulatory domains are now queried through a userspace agent through udev allowing distributions to update regulatory rules without updating the kernel. Each driver can regulatory_hint() a regulatory domain based on either their EEPROM mapped regulatory domain value to a respective ISO/IEC 3166-1 country code or pass an internally built regulatory domain. We also add support to let the user set the regulatory domain through userspace in case of faulty EEPROMs to further help compliance. Support for world roaming will be added soon for cards capable of this. For more information see: http://wireless.kernel.org/en/developers/Regulatory/CRDA For now we leave an option to enable the old module parameter, ieee80211_regdom, and to build the 3 old regdomains statically (US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY. These old static definitions and the module parameter is being scheduled for removal for 2.6.29. Note that if you use this you won't make use of a world regulatory domain as its pointless. If you leave this option enabled and if CRDA is present and you use US or JP we will try to ask CRDA to update us a regulatory domain for us. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-09-10 14:19:48 +08:00
regulatory_exit();
unregister_pernet_device(&cfg80211_pernet_ops);
destroy_workqueue(cfg80211_wq);
}
module_exit(cfg80211_exit);