linux_old1/net/batman-adv/packet.h

553 lines
18 KiB
C
Raw Normal View History

/* Copyright (C) 2007-2014 B.A.T.M.A.N. contributors:
*
* Marek Lindner, Simon Wunderlich
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of version 2 of the GNU General Public
* License as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, see <http://www.gnu.org/licenses/>.
*/
#ifndef _NET_BATMAN_ADV_PACKET_H_
#define _NET_BATMAN_ADV_PACKET_H_
/**
* enum batadv_packettype - types for batman-adv encapsulated packets
* @BATADV_IV_OGM: originator messages for B.A.T.M.A.N. IV
* @BATADV_BCAST: broadcast packets carrying broadcast payload
* @BATADV_CODED: network coded packets
*
* @BATADV_UNICAST: unicast packets carrying unicast payload traffic
* @BATADV_UNICAST_FRAG: unicast packets carrying a fragment of the original
* payload packet
* @BATADV_UNICAST_4ADDR: unicast packet including the originator address of
* the sender
* @BATADV_ICMP: unicast packet like IP ICMP used for ping or traceroute
* @BATADV_UNICAST_TVLV: unicast packet carrying TVLV containers
*/
enum batadv_packettype {
/* 0x00 - 0x3f: local packets or special rules for handling */
BATADV_IV_OGM = 0x00,
BATADV_BCAST = 0x01,
BATADV_CODED = 0x02,
/* 0x40 - 0x7f: unicast */
#define BATADV_UNICAST_MIN 0x40
BATADV_UNICAST = 0x40,
BATADV_UNICAST_FRAG = 0x41,
BATADV_UNICAST_4ADDR = 0x42,
BATADV_ICMP = 0x43,
BATADV_UNICAST_TVLV = 0x44,
#define BATADV_UNICAST_MAX 0x7f
/* 0x80 - 0xff: reserved */
};
/**
* enum batadv_subtype - packet subtype for unicast4addr
* @BATADV_P_DATA: user payload
* @BATADV_P_DAT_DHT_GET: DHT request message
* @BATADV_P_DAT_DHT_PUT: DHT store message
* @BATADV_P_DAT_CACHE_REPLY: ARP reply generated by DAT
*/
enum batadv_subtype {
BATADV_P_DATA = 0x01,
BATADV_P_DAT_DHT_GET = 0x02,
BATADV_P_DAT_DHT_PUT = 0x03,
BATADV_P_DAT_CACHE_REPLY = 0x04,
};
/* this file is included by batctl which needs these defines */
#define BATADV_COMPAT_VERSION 15
/**
* enum batadv_iv_flags - flags used in B.A.T.M.A.N. IV OGM packets
* @BATADV_NOT_BEST_NEXT_HOP: flag is set when ogm packet is forwarded and was
* previously received from someone else than the best neighbor.
* @BATADV_PRIMARIES_FIRST_HOP: flag is set when the primary interface address
* is used, and the packet travels its first hop.
* @BATADV_DIRECTLINK: flag is for the first hop or if rebroadcasted from a
* one hop neighbor on the interface where it was originally received.
*/
enum batadv_iv_flags {
BATADV_NOT_BEST_NEXT_HOP = BIT(0),
BATADV_PRIMARIES_FIRST_HOP = BIT(1),
BATADV_DIRECTLINK = BIT(2),
};
/* ICMP message types */
enum batadv_icmp_packettype {
BATADV_ECHO_REPLY = 0,
BATADV_DESTINATION_UNREACHABLE = 3,
BATADV_ECHO_REQUEST = 8,
BATADV_TTL_EXCEEDED = 11,
BATADV_PARAMETER_PROBLEM = 12,
};
/**
* enum batadv_mcast_flags - flags for multicast capabilities and settings
* @BATADV_MCAST_WANT_ALL_UNSNOOPABLES: we want all packets destined for
* 224.0.0.0/24 or ff02::1
batman-adv: Send multicast packets to nodes with a WANT_ALL flag With this patch a node sends IPv4 multicast packets to nodes which have a BATADV_MCAST_WANT_ALL_IPV4 flag set and IPv6 multicast packets to nodes which have a BATADV_MCAST_WANT_ALL_IPV6 flag set, too. Why is this needed? There are scenarios involving bridges where multicast report snooping and multicast TT announcements are not sufficient, which would lead to packet loss for some nodes otherwise: MLDv1 and IGMPv1/IGMPv2 have a suppression mechanism for multicast listener reports. When we have an MLDv1/IGMPv1/IGMPv2 querier behind a bridge then our snooping bridge is potentially not going to see any reports even though listeners exist because according to RFC4541 such reports are only forwarded to multicast routers: ----------------------------------------------------------- --------------- {Querier}---|Snoop. Switch|----{Listener} --------------- \ ^ ------- | br0 | < ??? ------- \ _-~---~_ _-~/ ~-_ ~ batman-adv \-----{Sender} \~_ cloud ~/ -~~__-__-~_/ I) MLDv1 Query: {Querier} -> flooded II) MLDv1 Report: {Listener} -> {Querier} -> br0 cannot detect the {Listener} => Packets from {Sender} need to be forwarded to all detected listeners and MLDv1/IGMPv1/IGMPv2 queriers. ----------------------------------------------------------- Note that we do not need to explicitly forward to MLDv2/IGMPv3 queriers, because these protocols have no report suppression: A bridge has no trouble detecting MLDv2/IGMPv3 listeners. Even though we do not support bridges yet we need to provide the according infrastructure already to not break compatibility later. Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2014-02-16 00:47:54 +08:00
* @BATADV_MCAST_WANT_ALL_IPV4: we want all IPv4 multicast packets
* @BATADV_MCAST_WANT_ALL_IPV6: we want all IPv6 multicast packets
*/
enum batadv_mcast_flags {
BATADV_MCAST_WANT_ALL_UNSNOOPABLES = BIT(0),
batman-adv: Send multicast packets to nodes with a WANT_ALL flag With this patch a node sends IPv4 multicast packets to nodes which have a BATADV_MCAST_WANT_ALL_IPV4 flag set and IPv6 multicast packets to nodes which have a BATADV_MCAST_WANT_ALL_IPV6 flag set, too. Why is this needed? There are scenarios involving bridges where multicast report snooping and multicast TT announcements are not sufficient, which would lead to packet loss for some nodes otherwise: MLDv1 and IGMPv1/IGMPv2 have a suppression mechanism for multicast listener reports. When we have an MLDv1/IGMPv1/IGMPv2 querier behind a bridge then our snooping bridge is potentially not going to see any reports even though listeners exist because according to RFC4541 such reports are only forwarded to multicast routers: ----------------------------------------------------------- --------------- {Querier}---|Snoop. Switch|----{Listener} --------------- \ ^ ------- | br0 | < ??? ------- \ _-~---~_ _-~/ ~-_ ~ batman-adv \-----{Sender} \~_ cloud ~/ -~~__-__-~_/ I) MLDv1 Query: {Querier} -> flooded II) MLDv1 Report: {Listener} -> {Querier} -> br0 cannot detect the {Listener} => Packets from {Sender} need to be forwarded to all detected listeners and MLDv1/IGMPv1/IGMPv2 queriers. ----------------------------------------------------------- Note that we do not need to explicitly forward to MLDv2/IGMPv3 queriers, because these protocols have no report suppression: A bridge has no trouble detecting MLDv2/IGMPv3 listeners. Even though we do not support bridges yet we need to provide the according infrastructure already to not break compatibility later. Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2014-02-16 00:47:54 +08:00
BATADV_MCAST_WANT_ALL_IPV4 = BIT(1),
BATADV_MCAST_WANT_ALL_IPV6 = BIT(2),
};
/* tt data subtypes */
#define BATADV_TT_DATA_TYPE_MASK 0x0F
batman-adv: improved client announcement mechanism The client announcement mechanism informs every mesh node in the network of any connected non-mesh client, in order to find the path towards that client from any given point in the mesh. The old implementation was based on the simple idea of appending a data buffer to each OGM containing all the client MAC addresses the node is serving. All other nodes can populate their global translation tables (table which links client MAC addresses to node addresses) using this MAC address buffer and linking it to the node's address contained in the OGM. A node that wants to contact a client has to lookup the node the client is connected to and its address in the global translation table. It is easy to understand that this implementation suffers from several issues: - big overhead (each and every OGM contains the entire list of connected clients) - high latencies for client route updates due to long OGM trip time and OGM losses The new implementation addresses these issues by appending client changes (new client joined or a client left) to the OGM instead of filling it with all the client addresses each time. In this way nodes can modify their global tables by means of "updates", thus reducing the overhead within the OGMs. To keep the entire network in sync each node maintains a translation table version number (ttvn) and a translation table checksum. These values are spread with the OGM to allow all the network participants to determine whether or not they need to update their translation table information. When a translation table lookup is performed in order to send a packet to a client attached to another node, the destination's ttvn is added to the payload packet. Forwarding nodes can compare the packet's ttvn with their destination's ttvn (this node could have a fresher information than the source) and re-route the packet if necessary. This greatly reduces the packet loss of clients roaming from one AP to the next. Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Sven Eckelmann <sven@narfation.org>
2011-04-27 20:27:44 +08:00
/**
* enum batadv_tt_data_flags - flags for tt data tvlv
* @BATADV_TT_OGM_DIFF: TT diff propagated through OGM
* @BATADV_TT_REQUEST: TT request message
* @BATADV_TT_RESPONSE: TT response message
* @BATADV_TT_FULL_TABLE: contains full table to replace existing table
*/
enum batadv_tt_data_flags {
BATADV_TT_OGM_DIFF = BIT(0),
BATADV_TT_REQUEST = BIT(1),
BATADV_TT_RESPONSE = BIT(2),
BATADV_TT_FULL_TABLE = BIT(4),
batman-adv: improved client announcement mechanism The client announcement mechanism informs every mesh node in the network of any connected non-mesh client, in order to find the path towards that client from any given point in the mesh. The old implementation was based on the simple idea of appending a data buffer to each OGM containing all the client MAC addresses the node is serving. All other nodes can populate their global translation tables (table which links client MAC addresses to node addresses) using this MAC address buffer and linking it to the node's address contained in the OGM. A node that wants to contact a client has to lookup the node the client is connected to and its address in the global translation table. It is easy to understand that this implementation suffers from several issues: - big overhead (each and every OGM contains the entire list of connected clients) - high latencies for client route updates due to long OGM trip time and OGM losses The new implementation addresses these issues by appending client changes (new client joined or a client left) to the OGM instead of filling it with all the client addresses each time. In this way nodes can modify their global tables by means of "updates", thus reducing the overhead within the OGMs. To keep the entire network in sync each node maintains a translation table version number (ttvn) and a translation table checksum. These values are spread with the OGM to allow all the network participants to determine whether or not they need to update their translation table information. When a translation table lookup is performed in order to send a packet to a client attached to another node, the destination's ttvn is added to the payload packet. Forwarding nodes can compare the packet's ttvn with their destination's ttvn (this node could have a fresher information than the source) and re-route the packet if necessary. This greatly reduces the packet loss of clients roaming from one AP to the next. Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Sven Eckelmann <sven@narfation.org>
2011-04-27 20:27:44 +08:00
};
/**
* enum batadv_tt_client_flags - TT client specific flags
* @BATADV_TT_CLIENT_DEL: the client has to be deleted from the table
* @BATADV_TT_CLIENT_ROAM: the client roamed to/from another node and the new
* update telling its new real location has not been received/sent yet
* @BATADV_TT_CLIENT_WIFI: this client is connected through a wifi interface.
* This information is used by the "AP Isolation" feature
* @BATADV_TT_CLIENT_ISOLA: this client is considered "isolated". This
* information is used by the Extended Isolation feature
* @BATADV_TT_CLIENT_NOPURGE: this client should never be removed from the table
* @BATADV_TT_CLIENT_NEW: this client has been added to the local table but has
* not been announced yet
* @BATADV_TT_CLIENT_PENDING: this client is marked for removal but it is kept
* in the table for one more originator interval for consistency purposes
* @BATADV_TT_CLIENT_TEMP: this global client has been detected to be part of
* the network but no nnode has already announced it
*
* Bits from 0 to 7 are called _remote flags_ because they are sent on the wire.
* Bits from 8 to 15 are called _local flags_ because they are used for local
* computations only.
*
* Bits from 4 to 7 - a subset of remote flags - are ensured to be in sync with
* the other nodes in the network. To achieve this goal these flags are included
* in the TT CRC computation.
*/
enum batadv_tt_client_flags {
BATADV_TT_CLIENT_DEL = BIT(0),
BATADV_TT_CLIENT_ROAM = BIT(1),
BATADV_TT_CLIENT_WIFI = BIT(4),
BATADV_TT_CLIENT_ISOLA = BIT(5),
BATADV_TT_CLIENT_NOPURGE = BIT(8),
BATADV_TT_CLIENT_NEW = BIT(9),
BATADV_TT_CLIENT_PENDING = BIT(10),
BATADV_TT_CLIENT_TEMP = BIT(11),
batman-adv: improved client announcement mechanism The client announcement mechanism informs every mesh node in the network of any connected non-mesh client, in order to find the path towards that client from any given point in the mesh. The old implementation was based on the simple idea of appending a data buffer to each OGM containing all the client MAC addresses the node is serving. All other nodes can populate their global translation tables (table which links client MAC addresses to node addresses) using this MAC address buffer and linking it to the node's address contained in the OGM. A node that wants to contact a client has to lookup the node the client is connected to and its address in the global translation table. It is easy to understand that this implementation suffers from several issues: - big overhead (each and every OGM contains the entire list of connected clients) - high latencies for client route updates due to long OGM trip time and OGM losses The new implementation addresses these issues by appending client changes (new client joined or a client left) to the OGM instead of filling it with all the client addresses each time. In this way nodes can modify their global tables by means of "updates", thus reducing the overhead within the OGMs. To keep the entire network in sync each node maintains a translation table version number (ttvn) and a translation table checksum. These values are spread with the OGM to allow all the network participants to determine whether or not they need to update their translation table information. When a translation table lookup is performed in order to send a packet to a client attached to another node, the destination's ttvn is added to the payload packet. Forwarding nodes can compare the packet's ttvn with their destination's ttvn (this node could have a fresher information than the source) and re-route the packet if necessary. This greatly reduces the packet loss of clients roaming from one AP to the next. Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Sven Eckelmann <sven@narfation.org>
2011-04-27 20:27:44 +08:00
};
/**
* batadv_vlan_flags - flags for the four MSB of any vlan ID field
* @BATADV_VLAN_HAS_TAG: whether the field contains a valid vlan tag or not
*/
enum batadv_vlan_flags {
BATADV_VLAN_HAS_TAG = BIT(15),
};
/* claim frame types for the bridge loop avoidance */
enum batadv_bla_claimframe {
BATADV_CLAIM_TYPE_CLAIM = 0x00,
BATADV_CLAIM_TYPE_UNCLAIM = 0x01,
BATADV_CLAIM_TYPE_ANNOUNCE = 0x02,
BATADV_CLAIM_TYPE_REQUEST = 0x03,
};
/**
* enum batadv_tvlv_type - tvlv type definitions
* @BATADV_TVLV_GW: gateway tvlv
* @BATADV_TVLV_DAT: distributed arp table tvlv
* @BATADV_TVLV_NC: network coding tvlv
* @BATADV_TVLV_TT: translation table tvlv
* @BATADV_TVLV_ROAM: roaming advertisement tvlv
* @BATADV_TVLV_MCAST: multicast capability tvlv
*/
enum batadv_tvlv_type {
BATADV_TVLV_GW = 0x01,
BATADV_TVLV_DAT = 0x02,
BATADV_TVLV_NC = 0x03,
BATADV_TVLV_TT = 0x04,
BATADV_TVLV_ROAM = 0x05,
BATADV_TVLV_MCAST = 0x06,
};
#pragma pack(2)
/* the destination hardware field in the ARP frame is used to
* transport the claim type and the group id
*/
struct batadv_bla_claim_dst {
uint8_t magic[3]; /* FF:43:05 */
uint8_t type; /* bla_claimframe */
__be16 group; /* group id */
};
#pragma pack()
/**
* struct batadv_ogm_packet - ogm (routing protocol) packet
* @packet_type: batman-adv packet type, part of the general header
* @version: batman-adv protocol version, part of the genereal header
* @ttl: time to live for this packet, part of the genereal header
* @flags: contains routing relevant flags - see enum batadv_iv_flags
* @tvlv_len: length of tvlv data following the ogm header
*/
struct batadv_ogm_packet {
uint8_t packet_type;
uint8_t version;
uint8_t ttl;
uint8_t flags;
__be32 seqno;
uint8_t orig[ETH_ALEN];
uint8_t prev_sender[ETH_ALEN];
uint8_t reserved;
uint8_t tq;
__be16 tvlv_len;
/* __packed is not needed as the struct size is divisible by 4,
* and the largest data type in this struct has a size of 4.
*/
};
#define BATADV_OGM_HLEN sizeof(struct batadv_ogm_packet)
/**
* batadv_icmp_header - common members among all the ICMP packets
* @packet_type: batman-adv packet type, part of the general header
* @version: batman-adv protocol version, part of the genereal header
* @ttl: time to live for this packet, part of the genereal header
* @msg_type: ICMP packet type
* @dst: address of the destination node
* @orig: address of the source node
* @uid: local ICMP socket identifier
* @align: not used - useful for alignment purposes only
*
* This structure is used for ICMP packets parsing only and it is never sent
* over the wire. The alignment field at the end is there to ensure that
* members are padded the same way as they are in real packets.
*/
struct batadv_icmp_header {
uint8_t packet_type;
uint8_t version;
uint8_t ttl;
uint8_t msg_type; /* see ICMP message types above */
uint8_t dst[ETH_ALEN];
uint8_t orig[ETH_ALEN];
uint8_t uid;
uint8_t align[3];
};
/**
* batadv_icmp_packet - ICMP packet
* @packet_type: batman-adv packet type, part of the general header
* @version: batman-adv protocol version, part of the genereal header
* @ttl: time to live for this packet, part of the genereal header
* @msg_type: ICMP packet type
* @dst: address of the destination node
* @orig: address of the source node
* @uid: local ICMP socket identifier
* @reserved: not used - useful for alignment
* @seqno: ICMP sequence number
*/
struct batadv_icmp_packet {
uint8_t packet_type;
uint8_t version;
uint8_t ttl;
uint8_t msg_type; /* see ICMP message types above */
uint8_t dst[ETH_ALEN];
uint8_t orig[ETH_ALEN];
uint8_t uid;
uint8_t reserved;
__be16 seqno;
};
#define BATADV_RR_LEN 16
/**
* batadv_icmp_packet_rr - ICMP RouteRecord packet
* @packet_type: batman-adv packet type, part of the general header
* @version: batman-adv protocol version, part of the genereal header
* @ttl: time to live for this packet, part of the genereal header
* @msg_type: ICMP packet type
* @dst: address of the destination node
* @orig: address of the source node
* @uid: local ICMP socket identifier
* @rr_cur: number of entries the rr array
* @seqno: ICMP sequence number
* @rr: route record array
*/
struct batadv_icmp_packet_rr {
uint8_t packet_type;
uint8_t version;
uint8_t ttl;
uint8_t msg_type; /* see ICMP message types above */
uint8_t dst[ETH_ALEN];
uint8_t orig[ETH_ALEN];
uint8_t uid;
uint8_t rr_cur;
__be16 seqno;
uint8_t rr[BATADV_RR_LEN][ETH_ALEN];
};
#define BATADV_ICMP_MAX_PACKET_SIZE sizeof(struct batadv_icmp_packet_rr)
/* All packet headers in front of an ethernet header have to be completely
* divisible by 2 but not by 4 to make the payload after the ethernet
* header again 4 bytes boundary aligned.
*
* A packing of 2 is necessary to avoid extra padding at the end of the struct
* caused by a structure member which is larger than two bytes. Otherwise
* the structure would not fulfill the previously mentioned rule to avoid the
* misalignment of the payload after the ethernet header. It may also lead to
* leakage of information when the padding it not initialized before sending.
*/
#pragma pack(2)
/**
* struct batadv_unicast_packet - unicast packet for network payload
* @packet_type: batman-adv packet type, part of the general header
* @version: batman-adv protocol version, part of the genereal header
* @ttl: time to live for this packet, part of the genereal header
* @ttvn: translation table version number
* @dest: originator destination of the unicast packet
*/
struct batadv_unicast_packet {
uint8_t packet_type;
uint8_t version;
uint8_t ttl;
batman-adv: improved client announcement mechanism The client announcement mechanism informs every mesh node in the network of any connected non-mesh client, in order to find the path towards that client from any given point in the mesh. The old implementation was based on the simple idea of appending a data buffer to each OGM containing all the client MAC addresses the node is serving. All other nodes can populate their global translation tables (table which links client MAC addresses to node addresses) using this MAC address buffer and linking it to the node's address contained in the OGM. A node that wants to contact a client has to lookup the node the client is connected to and its address in the global translation table. It is easy to understand that this implementation suffers from several issues: - big overhead (each and every OGM contains the entire list of connected clients) - high latencies for client route updates due to long OGM trip time and OGM losses The new implementation addresses these issues by appending client changes (new client joined or a client left) to the OGM instead of filling it with all the client addresses each time. In this way nodes can modify their global tables by means of "updates", thus reducing the overhead within the OGMs. To keep the entire network in sync each node maintains a translation table version number (ttvn) and a translation table checksum. These values are spread with the OGM to allow all the network participants to determine whether or not they need to update their translation table information. When a translation table lookup is performed in order to send a packet to a client attached to another node, the destination's ttvn is added to the payload packet. Forwarding nodes can compare the packet's ttvn with their destination's ttvn (this node could have a fresher information than the source) and re-route the packet if necessary. This greatly reduces the packet loss of clients roaming from one AP to the next. Signed-off-by: Antonio Quartulli <ordex@autistici.org> Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Sven Eckelmann <sven@narfation.org>
2011-04-27 20:27:44 +08:00
uint8_t ttvn; /* destination translation table version number */
uint8_t dest[ETH_ALEN];
/* "4 bytes boundary + 2 bytes" long to make the payload after the
* following ethernet header again 4 bytes boundary aligned
*/
};
/**
* struct batadv_unicast_4addr_packet - extended unicast packet
* @u: common unicast packet header
* @src: address of the source
* @subtype: packet subtype
*/
struct batadv_unicast_4addr_packet {
struct batadv_unicast_packet u;
uint8_t src[ETH_ALEN];
uint8_t subtype;
uint8_t reserved;
/* "4 bytes boundary + 2 bytes" long to make the payload after the
* following ethernet header again 4 bytes boundary aligned
*/
};
/**
* struct batadv_frag_packet - fragmented packet
* @packet_type: batman-adv packet type, part of the general header
* @version: batman-adv protocol version, part of the genereal header
* @ttl: time to live for this packet, part of the genereal header
* @dest: final destination used when routing fragments
* @orig: originator of the fragment used when merging the packet
* @no: fragment number within this sequence
* @reserved: reserved byte for alignment
* @seqno: sequence identification
* @total_size: size of the merged packet
*/
struct batadv_frag_packet {
uint8_t packet_type;
uint8_t version; /* batman version field */
uint8_t ttl;
#if defined(__BIG_ENDIAN_BITFIELD)
uint8_t no:4;
uint8_t reserved:4;
#elif defined(__LITTLE_ENDIAN_BITFIELD)
uint8_t reserved:4;
uint8_t no:4;
#else
#error "unknown bitfield endianess"
#endif
uint8_t dest[ETH_ALEN];
uint8_t orig[ETH_ALEN];
__be16 seqno;
__be16 total_size;
};
/**
* struct batadv_bcast_packet - broadcast packet for network payload
* @packet_type: batman-adv packet type, part of the general header
* @version: batman-adv protocol version, part of the genereal header
* @ttl: time to live for this packet, part of the genereal header
* @reserved: reserved byte for alignment
* @seqno: sequence identification
* @orig: originator of the broadcast packet
*/
struct batadv_bcast_packet {
uint8_t packet_type;
uint8_t version; /* batman version field */
uint8_t ttl;
uint8_t reserved;
__be32 seqno;
uint8_t orig[ETH_ALEN];
/* "4 bytes boundary + 2 bytes" long to make the payload after the
* following ethernet header again 4 bytes boundary aligned
*/
};
/**
* struct batadv_coded_packet - network coded packet
* @packet_type: batman-adv packet type, part of the general header
* @version: batman-adv protocol version, part of the genereal header
* @ttl: time to live for this packet, part of the genereal header
* @reserved: Align following fields to 2-byte boundaries
* @first_source: original source of first included packet
* @first_orig_dest: original destinal of first included packet
* @first_crc: checksum of first included packet
* @first_ttvn: tt-version number of first included packet
* @second_ttl: ttl of second packet
* @second_dest: second receiver of this coded packet
* @second_source: original source of second included packet
* @second_orig_dest: original destination of second included packet
* @second_crc: checksum of second included packet
* @second_ttvn: tt version number of second included packet
* @coded_len: length of network coded part of the payload
*/
struct batadv_coded_packet {
uint8_t packet_type;
uint8_t version; /* batman version field */
uint8_t ttl;
uint8_t first_ttvn;
/* uint8_t first_dest[ETH_ALEN]; - saved in mac header destination */
uint8_t first_source[ETH_ALEN];
uint8_t first_orig_dest[ETH_ALEN];
__be32 first_crc;
uint8_t second_ttl;
uint8_t second_ttvn;
uint8_t second_dest[ETH_ALEN];
uint8_t second_source[ETH_ALEN];
uint8_t second_orig_dest[ETH_ALEN];
__be32 second_crc;
__be16 coded_len;
};
#pragma pack()
/**
* struct batadv_unicast_tvlv - generic unicast packet with tvlv payload
* @packet_type: batman-adv packet type, part of the general header
* @version: batman-adv protocol version, part of the genereal header
* @ttl: time to live for this packet, part of the genereal header
* @reserved: reserved field (for packet alignment)
* @src: address of the source
* @dst: address of the destination
* @tvlv_len: length of tvlv data following the unicast tvlv header
* @align: 2 bytes to align the header to a 4 byte boundry
*/
struct batadv_unicast_tvlv_packet {
uint8_t packet_type;
uint8_t version; /* batman version field */
uint8_t ttl;
uint8_t reserved;
uint8_t dst[ETH_ALEN];
uint8_t src[ETH_ALEN];
__be16 tvlv_len;
uint16_t align;
};
/**
* struct batadv_tvlv_hdr - base tvlv header struct
* @type: tvlv container type (see batadv_tvlv_type)
* @version: tvlv container version
* @len: tvlv container length
*/
struct batadv_tvlv_hdr {
uint8_t type;
uint8_t version;
__be16 len;
};
/**
* struct batadv_tvlv_gateway_data - gateway data propagated through gw tvlv
* container
* @bandwidth_down: advertised uplink download bandwidth
* @bandwidth_up: advertised uplink upload bandwidth
*/
struct batadv_tvlv_gateway_data {
__be32 bandwidth_down;
__be32 bandwidth_up;
};
/**
* struct batadv_tvlv_tt_data - tt data propagated through the tt tvlv container
* @flags: translation table flags (see batadv_tt_data_flags)
* @ttvn: translation table version number
* @vlan_num: number of announced VLANs. In the TVLV this struct is followed by
* one batadv_tvlv_tt_vlan_data object per announced vlan
*/
struct batadv_tvlv_tt_data {
uint8_t flags;
uint8_t ttvn;
__be16 num_vlan;
};
/**
* struct batadv_tvlv_tt_vlan_data - vlan specific tt data propagated through
* the tt tvlv container
* @crc: crc32 checksum of the entries belonging to this vlan
* @vid: vlan identifier
* @reserved: unused, useful for alignment purposes
*/
struct batadv_tvlv_tt_vlan_data {
__be32 crc;
__be16 vid;
uint16_t reserved;
};
/**
* struct batadv_tvlv_tt_change - translation table diff data
* @flags: status indicators concerning the non-mesh client (see
* batadv_tt_client_flags)
* @reserved: reserved field - useful for alignment purposes only
* @addr: mac address of non-mesh client that triggered this tt change
* @vid: VLAN identifier
*/
struct batadv_tvlv_tt_change {
uint8_t flags;
uint8_t reserved[3];
uint8_t addr[ETH_ALEN];
__be16 vid;
};
/**
* struct batadv_tvlv_roam_adv - roaming advertisement
* @client: mac address of roaming client
* @vid: VLAN identifier
*/
struct batadv_tvlv_roam_adv {
uint8_t client[ETH_ALEN];
__be16 vid;
};
/**
* struct batadv_tvlv_mcast_data - payload of a multicast tvlv
* @flags: multicast flags announced by the orig node
* @reserved: reserved field
*/
struct batadv_tvlv_mcast_data {
uint8_t flags;
uint8_t reserved[3];
};
#endif /* _NET_BATMAN_ADV_PACKET_H_ */