linux_old1/net/mac80211/sta_info.c

1523 lines
38 KiB
C
Raw Normal View History

/*
* Copyright 2002-2005, Instant802 Networks, Inc.
* Copyright 2006-2007 Jiri Benc <jbenc@suse.cz>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/etherdevice.h>
#include <linux/netdevice.h>
#include <linux/types.h>
#include <linux/slab.h>
#include <linux/skbuff.h>
#include <linux/if_arp.h>
#include <linux/timer.h>
#include <linux/rtnetlink.h>
#include <net/mac80211.h>
#include "ieee80211_i.h"
#include "driver-ops.h"
#include "rate.h"
#include "sta_info.h"
#include "debugfs_sta.h"
#include "mesh.h"
#include "wme.h"
/**
* DOC: STA information lifetime rules
*
* STA info structures (&struct sta_info) are managed in a hash table
* for faster lookup and a list for iteration. They are managed using
* RCU, i.e. access to the list and hash table is protected by RCU.
*
* Upon allocating a STA info structure with sta_info_alloc(), the caller
* owns that structure. It must then insert it into the hash table using
* either sta_info_insert() or sta_info_insert_rcu(); only in the latter
* case (which acquires an rcu read section but must not be called from
* within one) will the pointer still be valid after the call. Note that
* the caller may not do much with the STA info before inserting it, in
* particular, it may not start any mesh peer link management or add
* encryption keys.
*
* When the insertion fails (sta_info_insert()) returns non-zero), the
* structure will have been freed by sta_info_insert()!
*
* Station entries are added by mac80211 when you establish a link with a
* peer. This means different things for the different type of interfaces
* we support. For a regular station this mean we add the AP sta when we
* receive an association response from the AP. For IBSS this occurs when
* get to know about a peer on the same IBSS. For WDS we add the sta for
* the peer immediately upon device open. When using AP mode we add stations
* for each respective station upon request from userspace through nl80211.
*
* In order to remove a STA info structure, various sta_info_destroy_*()
* calls are available.
*
* There is no concept of ownership on a STA entry, each structure is
* owned by the global hash table/list until it is removed. All users of
* the structure need to be RCU protected so that the structure won't be
* freed before they are done using it.
*/
/* Caller must hold local->sta_mtx */
static int sta_info_hash_del(struct ieee80211_local *local,
struct sta_info *sta)
{
struct sta_info *s;
s = rcu_dereference_protected(local->sta_hash[STA_HASH(sta->sta.addr)],
lockdep_is_held(&local->sta_mtx));
if (!s)
return -ENOENT;
if (s == sta) {
rcu_assign_pointer(local->sta_hash[STA_HASH(sta->sta.addr)],
s->hnext);
return 0;
}
while (rcu_access_pointer(s->hnext) &&
rcu_access_pointer(s->hnext) != sta)
s = rcu_dereference_protected(s->hnext,
lockdep_is_held(&local->sta_mtx));
if (rcu_access_pointer(s->hnext)) {
rcu_assign_pointer(s->hnext, sta->hnext);
return 0;
}
return -ENOENT;
}
static void cleanup_single_sta(struct sta_info *sta)
{
int ac, i;
struct tid_ampdu_tx *tid_tx;
struct ieee80211_sub_if_data *sdata = sta->sdata;
struct ieee80211_local *local = sdata->local;
struct ps_data *ps;
/*
* At this point, when being called as call_rcu callback,
* neither mac80211 nor the driver can reference this
* sta struct any more except by still existing timers
* associated with this station that we clean up below.
*
* Note though that this still uses the sdata and even
* calls the driver in AP and mesh mode, so interfaces
* of those types mush use call sta_info_flush_cleanup()
* (typically via sta_info_flush()) before deconfiguring
* the driver.
*
* In station mode, nothing happens here so it doesn't
* have to (and doesn't) do that, this is intentional to
* speed up roaming.
*/
if (test_sta_flag(sta, WLAN_STA_PS_STA)) {
if (sta->sdata->vif.type == NL80211_IFTYPE_AP ||
sta->sdata->vif.type == NL80211_IFTYPE_AP_VLAN)
ps = &sdata->bss->ps;
mac80211: mesh power save basics Add routines to - maintain a PS mode for each peer and a non-peer PS mode - indicate own PS mode in transmitted frames - track neighbor STAs power modes - buffer frames when neighbors are in PS mode - add TIM and Awake Window IE to beacons - release frames in Mesh Peer Service Periods Add local_pm to sta_info to represent the link-specific power mode at this station towards the remote station. When a peer link is established, use the default power mode stored in mesh config. Update the PS status if the peering status of a neighbor changes. Maintain a mesh power mode for non-peer mesh STAs. Set the non-peer power mode to active mode during peering. Authenticated mesh peering is currently not working when either node is configured to be in power save mode. Indicate the current power mode in transmitted frames. Use QoS Nulls to indicate mesh power mode transitions. For performance reasons, calls to the function setting the frame flags are placed in HWMP routing routines, as there the STA pointer is already available. Add peer_pm to sta_info to represent the peer's link-specific power mode towards the local station. Add nonpeer_pm to represent the peer's power mode towards all non-peer stations. Track power modes based on received frames. Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS neighbor counter and group-addressed frame buffer). Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame buffering routines in the tx path. Update num_sta_ps to buffer and release group-addressed frames after DTIM beacons. Announce the awake window duration in beacons if in light or deep sleep mode towards any peer or non-peer. Create a TIM IE similarly to AP mode and add it to mesh beacons. Parse received Awake Window IEs and check TIM IEs for buffered frames. Release frames towards peers in mesh Peer Service Periods. Use the corresponding trigger frames and monitor the MPSP status. Append a QoS Null as trigger frame if neccessary to properly end the MPSP. Currently, in HT channels MPSPs behave imperfectly and show large delay spikes and frame losses. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com> Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31 01:14:08 +08:00
else if (ieee80211_vif_is_mesh(&sdata->vif))
ps = &sdata->u.mesh.ps;
else
return;
clear_sta_flag(sta, WLAN_STA_PS_STA);
atomic_dec(&ps->num_sta_ps);
sta_info_recalc_tim(sta);
}
for (ac = 0; ac < IEEE80211_NUM_ACS; ac++) {
local->total_ps_buffered -= skb_queue_len(&sta->ps_tx_buf[ac]);
ieee80211_purge_tx_queue(&local->hw, &sta->ps_tx_buf[ac]);
ieee80211_purge_tx_queue(&local->hw, &sta->tx_filtered[ac]);
}
if (ieee80211_vif_is_mesh(&sdata->vif))
mesh_sta_cleanup(sta);
cancel_work_sync(&sta->drv_unblock_wk);
/*
* Destroy aggregation state here. It would be nice to wait for the
* driver to finish aggregation stop and then clean up, but for now
* drivers have to handle aggregation stop being requested, followed
* directly by station destruction.
*/
for (i = 0; i < IEEE80211_NUM_TIDS; i++) {
kfree(sta->ampdu_mlme.tid_start_tx[i]);
tid_tx = rcu_dereference_raw(sta->ampdu_mlme.tid_tx[i]);
if (!tid_tx)
continue;
ieee80211_purge_tx_queue(&local->hw, &tid_tx->pending);
kfree(tid_tx);
}
sta_info_free(local, sta);
}
void ieee80211_cleanup_sdata_stas(struct ieee80211_sub_if_data *sdata)
{
struct sta_info *sta;
spin_lock_bh(&sdata->cleanup_stations_lock);
while (!list_empty(&sdata->cleanup_stations)) {
sta = list_first_entry(&sdata->cleanup_stations,
struct sta_info, list);
list_del(&sta->list);
spin_unlock_bh(&sdata->cleanup_stations_lock);
cleanup_single_sta(sta);
spin_lock_bh(&sdata->cleanup_stations_lock);
}
spin_unlock_bh(&sdata->cleanup_stations_lock);
}
static void free_sta_rcu(struct rcu_head *h)
{
struct sta_info *sta = container_of(h, struct sta_info, rcu_head);
struct ieee80211_sub_if_data *sdata = sta->sdata;
spin_lock(&sdata->cleanup_stations_lock);
list_add_tail(&sta->list, &sdata->cleanup_stations);
spin_unlock(&sdata->cleanup_stations_lock);
ieee80211_queue_work(&sdata->local->hw, &sdata->cleanup_stations_wk);
}
/* protected by RCU */
struct sta_info *sta_info_get(struct ieee80211_sub_if_data *sdata,
const u8 *addr)
{
struct ieee80211_local *local = sdata->local;
struct sta_info *sta;
sta = rcu_dereference_check(local->sta_hash[STA_HASH(addr)],
lockdep_is_held(&local->sta_mtx));
while (sta) {
if (sta->sdata == sdata &&
ether_addr_equal(sta->sta.addr, addr))
break;
sta = rcu_dereference_check(sta->hnext,
lockdep_is_held(&local->sta_mtx));
}
return sta;
}
/*
* Get sta info either from the specified interface
* or from one of its vlans
*/
struct sta_info *sta_info_get_bss(struct ieee80211_sub_if_data *sdata,
const u8 *addr)
{
struct ieee80211_local *local = sdata->local;
struct sta_info *sta;
sta = rcu_dereference_check(local->sta_hash[STA_HASH(addr)],
lockdep_is_held(&local->sta_mtx));
while (sta) {
if ((sta->sdata == sdata ||
(sta->sdata->bss && sta->sdata->bss == sdata->bss)) &&
ether_addr_equal(sta->sta.addr, addr))
break;
sta = rcu_dereference_check(sta->hnext,
lockdep_is_held(&local->sta_mtx));
}
return sta;
}
struct sta_info *sta_info_get_by_idx(struct ieee80211_sub_if_data *sdata,
int idx)
{
struct ieee80211_local *local = sdata->local;
struct sta_info *sta;
int i = 0;
list_for_each_entry_rcu(sta, &local->sta_list, list) {
if (sdata != sta->sdata)
continue;
if (i < idx) {
++i;
continue;
}
return sta;
}
return NULL;
}
/**
* sta_info_free - free STA
*
* @local: pointer to the global information
* @sta: STA info to free
*
* This function must undo everything done by sta_info_alloc()
* that may happen before sta_info_insert(). It may only be
* called when sta_info_insert() has not been attempted (and
* if that fails, the station is freed anyway.)
*/
void sta_info_free(struct ieee80211_local *local, struct sta_info *sta)
{
if (sta->rate_ctrl)
rate_control_free_sta(sta);
sta_dbg(sta->sdata, "Destroyed STA %pM\n", sta->sta.addr);
kfree(sta);
}
/* Caller must hold local->sta_mtx */
static void sta_info_hash_add(struct ieee80211_local *local,
struct sta_info *sta)
{
lockdep_assert_held(&local->sta_mtx);
sta->hnext = local->sta_hash[STA_HASH(sta->sta.addr)];
rcu_assign_pointer(local->sta_hash[STA_HASH(sta->sta.addr)], sta);
}
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
static void sta_unblock(struct work_struct *wk)
{
struct sta_info *sta;
sta = container_of(wk, struct sta_info, drv_unblock_wk);
if (sta->dead)
return;
if (!test_sta_flag(sta, WLAN_STA_PS_STA)) {
local_bh_disable();
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
ieee80211_sta_ps_deliver_wakeup(sta);
local_bh_enable();
} else if (test_and_clear_sta_flag(sta, WLAN_STA_PSPOLL)) {
clear_sta_flag(sta, WLAN_STA_PS_DRIVER);
local_bh_disable();
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
ieee80211_sta_ps_deliver_poll_response(sta);
local_bh_enable();
} else if (test_and_clear_sta_flag(sta, WLAN_STA_UAPSD)) {
clear_sta_flag(sta, WLAN_STA_PS_DRIVER);
local_bh_disable();
ieee80211_sta_ps_deliver_uapsd(sta);
local_bh_enable();
} else
clear_sta_flag(sta, WLAN_STA_PS_DRIVER);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
}
static int sta_prepare_rate_control(struct ieee80211_local *local,
struct sta_info *sta, gfp_t gfp)
{
if (local->hw.flags & IEEE80211_HW_HAS_RATE_CONTROL)
return 0;
sta->rate_ctrl = local->rate_ctrl;
sta->rate_ctrl_priv = rate_control_alloc_sta(sta->rate_ctrl,
&sta->sta, gfp);
if (!sta->rate_ctrl_priv)
return -ENOMEM;
return 0;
}
struct sta_info *sta_info_alloc(struct ieee80211_sub_if_data *sdata,
const u8 *addr, gfp_t gfp)
{
struct ieee80211_local *local = sdata->local;
struct sta_info *sta;
struct timespec uptime;
int i;
sta = kzalloc(sizeof(*sta) + local->hw.sta_data_size, gfp);
if (!sta)
return NULL;
spin_lock_init(&sta->lock);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
INIT_WORK(&sta->drv_unblock_wk, sta_unblock);
INIT_WORK(&sta->ampdu_mlme.work, ieee80211_ba_session_work);
mutex_init(&sta->ampdu_mlme.mtx);
#ifdef CONFIG_MAC80211_MESH
if (ieee80211_vif_is_mesh(&sdata->vif) &&
!sdata->u.mesh.user_mpm)
init_timer(&sta->plink_timer);
sta->nonpeer_pm = NL80211_MESH_POWER_ACTIVE;
#endif
memcpy(sta->sta.addr, addr, ETH_ALEN);
sta->local = local;
sta->sdata = sdata;
sta->last_rx = jiffies;
sta->sta_state = IEEE80211_STA_NONE;
do_posix_clock_monotonic_gettime(&uptime);
sta->last_connected = uptime.tv_sec;
ewma_init(&sta->avg_signal, 1024, 8);
for (i = 0; i < ARRAY_SIZE(sta->chain_signal_avg); i++)
ewma_init(&sta->chain_signal_avg[i], 1024, 8);
if (sta_prepare_rate_control(local, sta, gfp)) {
kfree(sta);
return NULL;
}
for (i = 0; i < IEEE80211_NUM_TIDS; i++) {
/*
* timer_to_tid must be initialized with identity mapping
* to enable session_timer's data differentiation. See
* sta_rx_agg_session_timer_expired for usage.
*/
sta->timer_to_tid[i] = i;
}
for (i = 0; i < IEEE80211_NUM_ACS; i++) {
skb_queue_head_init(&sta->ps_tx_buf[i]);
skb_queue_head_init(&sta->tx_filtered[i]);
}
for (i = 0; i < IEEE80211_NUM_TIDS; i++)
sta->last_seq_ctrl[i] = cpu_to_le16(USHRT_MAX);
sta->sta.smps_mode = IEEE80211_SMPS_OFF;
sta_dbg(sdata, "Allocated STA %pM\n", sta->sta.addr);
return sta;
}
static int sta_info_insert_check(struct sta_info *sta)
{
struct ieee80211_sub_if_data *sdata = sta->sdata;
/*
* Can't be a WARN_ON because it can be triggered through a race:
* something inserts a STA (on one CPU) without holding the RTNL
* and another CPU turns off the net device.
*/
if (unlikely(!ieee80211_sdata_running(sdata)))
return -ENETDOWN;
if (WARN_ON(ether_addr_equal(sta->sta.addr, sdata->vif.addr) ||
is_multicast_ether_addr(sta->sta.addr)))
return -EINVAL;
return 0;
}
static int sta_info_insert_drv_state(struct ieee80211_local *local,
struct ieee80211_sub_if_data *sdata,
struct sta_info *sta)
{
enum ieee80211_sta_state state;
int err = 0;
for (state = IEEE80211_STA_NOTEXIST; state < sta->sta_state; state++) {
err = drv_sta_state(local, sdata, sta, state, state + 1);
if (err)
break;
}
if (!err) {
/*
* Drivers using legacy sta_add/sta_remove callbacks only
* get uploaded set to true after sta_add is called.
*/
if (!local->ops->sta_add)
sta->uploaded = true;
return 0;
}
if (sdata->vif.type == NL80211_IFTYPE_ADHOC) {
sdata_info(sdata,
"failed to move IBSS STA %pM to state %d (%d) - keeping it anyway\n",
sta->sta.addr, state + 1, err);
err = 0;
}
/* unwind on error */
for (; state > IEEE80211_STA_NOTEXIST; state--)
WARN_ON(drv_sta_state(local, sdata, sta, state, state - 1));
return err;
}
/*
* should be called with sta_mtx locked
* this function replaces the mutex lock
* with a RCU lock
*/
static int sta_info_insert_finish(struct sta_info *sta) __acquires(RCU)
{
struct ieee80211_local *local = sta->local;
struct ieee80211_sub_if_data *sdata = sta->sdata;
struct station_info sinfo;
int err = 0;
lockdep_assert_held(&local->sta_mtx);
/* check if STA exists already */
if (sta_info_get_bss(sdata, sta->sta.addr)) {
err = -EEXIST;
goto out_err;
}
/* notify driver */
err = sta_info_insert_drv_state(local, sdata, sta);
if (err)
goto out_err;
local->num_sta++;
local->sta_generation++;
smp_mb();
/* make the station visible */
sta_info_hash_add(local, sta);
list_add_rcu(&sta->list, &local->sta_list);
set_sta_flag(sta, WLAN_STA_INSERTED);
ieee80211_sta_debugfs_add(sta);
rate_control_add_sta_debugfs(sta);
memset(&sinfo, 0, sizeof(sinfo));
sinfo.filled = 0;
sinfo.generation = local->sta_generation;
cfg80211_new_sta(sdata->dev, sta->sta.addr, &sinfo, GFP_KERNEL);
sta_dbg(sdata, "Inserted STA %pM\n", sta->sta.addr);
/* move reference to rcu-protected */
rcu_read_lock();
mutex_unlock(&local->sta_mtx);
if (ieee80211_vif_is_mesh(&sdata->vif))
mesh_accept_plinks_update(sdata);
return 0;
out_err:
mutex_unlock(&local->sta_mtx);
rcu_read_lock();
return err;
}
int sta_info_insert_rcu(struct sta_info *sta) __acquires(RCU)
{
struct ieee80211_local *local = sta->local;
int err = 0;
might_sleep();
err = sta_info_insert_check(sta);
if (err) {
rcu_read_lock();
goto out_free;
}
mutex_lock(&local->sta_mtx);
err = sta_info_insert_finish(sta);
if (err)
goto out_free;
return 0;
out_free:
BUG_ON(!err);
sta_info_free(local, sta);
return err;
}
int sta_info_insert(struct sta_info *sta)
{
int err = sta_info_insert_rcu(sta);
rcu_read_unlock();
return err;
}
static inline void __bss_tim_set(u8 *tim, u16 id)
{
/*
* This format has been mandated by the IEEE specifications,
* so this line may not be changed to use the __set_bit() format.
*/
tim[id / 8] |= (1 << (id % 8));
}
static inline void __bss_tim_clear(u8 *tim, u16 id)
{
/*
* This format has been mandated by the IEEE specifications,
* so this line may not be changed to use the __clear_bit() format.
*/
tim[id / 8] &= ~(1 << (id % 8));
}
static inline bool __bss_tim_get(u8 *tim, u16 id)
{
/*
* This format has been mandated by the IEEE specifications,
* so this line may not be changed to use the test_bit() format.
*/
return tim[id / 8] & (1 << (id % 8));
}
static unsigned long ieee80211_tids_for_ac(int ac)
{
/* If we ever support TIDs > 7, this obviously needs to be adjusted */
switch (ac) {
case IEEE80211_AC_VO:
return BIT(6) | BIT(7);
case IEEE80211_AC_VI:
return BIT(4) | BIT(5);
case IEEE80211_AC_BE:
return BIT(0) | BIT(3);
case IEEE80211_AC_BK:
return BIT(1) | BIT(2);
default:
WARN_ON(1);
return 0;
}
}
void sta_info_recalc_tim(struct sta_info *sta)
{
struct ieee80211_local *local = sta->local;
struct ps_data *ps;
bool indicate_tim = false;
u8 ignore_for_tim = sta->sta.uapsd_queues;
int ac;
u16 id;
if (sta->sdata->vif.type == NL80211_IFTYPE_AP ||
sta->sdata->vif.type == NL80211_IFTYPE_AP_VLAN) {
if (WARN_ON_ONCE(!sta->sdata->bss))
return;
ps = &sta->sdata->bss->ps;
id = sta->sta.aid;
mac80211: mesh power save basics Add routines to - maintain a PS mode for each peer and a non-peer PS mode - indicate own PS mode in transmitted frames - track neighbor STAs power modes - buffer frames when neighbors are in PS mode - add TIM and Awake Window IE to beacons - release frames in Mesh Peer Service Periods Add local_pm to sta_info to represent the link-specific power mode at this station towards the remote station. When a peer link is established, use the default power mode stored in mesh config. Update the PS status if the peering status of a neighbor changes. Maintain a mesh power mode for non-peer mesh STAs. Set the non-peer power mode to active mode during peering. Authenticated mesh peering is currently not working when either node is configured to be in power save mode. Indicate the current power mode in transmitted frames. Use QoS Nulls to indicate mesh power mode transitions. For performance reasons, calls to the function setting the frame flags are placed in HWMP routing routines, as there the STA pointer is already available. Add peer_pm to sta_info to represent the peer's link-specific power mode towards the local station. Add nonpeer_pm to represent the peer's power mode towards all non-peer stations. Track power modes based on received frames. Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS neighbor counter and group-addressed frame buffer). Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame buffering routines in the tx path. Update num_sta_ps to buffer and release group-addressed frames after DTIM beacons. Announce the awake window duration in beacons if in light or deep sleep mode towards any peer or non-peer. Create a TIM IE similarly to AP mode and add it to mesh beacons. Parse received Awake Window IEs and check TIM IEs for buffered frames. Release frames towards peers in mesh Peer Service Periods. Use the corresponding trigger frames and monitor the MPSP status. Append a QoS Null as trigger frame if neccessary to properly end the MPSP. Currently, in HT channels MPSPs behave imperfectly and show large delay spikes and frame losses. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com> Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31 01:14:08 +08:00
#ifdef CONFIG_MAC80211_MESH
} else if (ieee80211_vif_is_mesh(&sta->sdata->vif)) {
ps = &sta->sdata->u.mesh.ps;
/* TIM map only for PLID <= IEEE80211_MAX_AID */
id = le16_to_cpu(sta->plid) % IEEE80211_MAX_AID;
#endif
} else {
return;
}
/* No need to do anything if the driver does all */
if (local->hw.flags & IEEE80211_HW_AP_LINK_PS)
return;
if (sta->dead)
goto done;
/*
* If all ACs are delivery-enabled then we should build
* the TIM bit for all ACs anyway; if only some are then
* we ignore those and build the TIM bit using only the
* non-enabled ones.
*/
if (ignore_for_tim == BIT(IEEE80211_NUM_ACS) - 1)
ignore_for_tim = 0;
for (ac = 0; ac < IEEE80211_NUM_ACS; ac++) {
unsigned long tids;
if (ignore_for_tim & BIT(ac))
continue;
indicate_tim |= !skb_queue_empty(&sta->tx_filtered[ac]) ||
!skb_queue_empty(&sta->ps_tx_buf[ac]);
if (indicate_tim)
break;
tids = ieee80211_tids_for_ac(ac);
indicate_tim |=
sta->driver_buffered_tids & tids;
}
done:
spin_lock_bh(&local->tim_lock);
if (indicate_tim == __bss_tim_get(ps->tim, id))
goto out_unlock;
if (indicate_tim)
__bss_tim_set(ps->tim, id);
else
__bss_tim_clear(ps->tim, id);
if (local->ops->set_tim) {
local->tim_in_locked_section = true;
drv_set_tim(local, &sta->sta, indicate_tim);
local->tim_in_locked_section = false;
}
out_unlock:
spin_unlock_bh(&local->tim_lock);
}
static bool sta_info_buffer_expired(struct sta_info *sta, struct sk_buff *skb)
{
struct ieee80211_tx_info *info;
int timeout;
if (!skb)
return false;
info = IEEE80211_SKB_CB(skb);
/* Timeout: (2 * listen_interval * beacon_int * 1024 / 1000000) sec */
timeout = (sta->listen_interval *
sta->sdata->vif.bss_conf.beacon_int *
32 / 15625) * HZ;
if (timeout < STA_TX_BUFFER_EXPIRE)
timeout = STA_TX_BUFFER_EXPIRE;
return time_after(jiffies, info->control.jiffies + timeout);
}
static bool sta_info_cleanup_expire_buffered_ac(struct ieee80211_local *local,
struct sta_info *sta, int ac)
{
unsigned long flags;
struct sk_buff *skb;
/*
* First check for frames that should expire on the filtered
* queue. Frames here were rejected by the driver and are on
* a separate queue to avoid reordering with normal PS-buffered
* frames. They also aren't accounted for right now in the
* total_ps_buffered counter.
*/
for (;;) {
spin_lock_irqsave(&sta->tx_filtered[ac].lock, flags);
skb = skb_peek(&sta->tx_filtered[ac]);
if (sta_info_buffer_expired(sta, skb))
skb = __skb_dequeue(&sta->tx_filtered[ac]);
else
skb = NULL;
spin_unlock_irqrestore(&sta->tx_filtered[ac].lock, flags);
/*
* Frames are queued in order, so if this one
* hasn't expired yet we can stop testing. If
* we actually reached the end of the queue we
* also need to stop, of course.
*/
if (!skb)
break;
ieee80211_free_txskb(&local->hw, skb);
}
/*
* Now also check the normal PS-buffered queue, this will
* only find something if the filtered queue was emptied
* since the filtered frames are all before the normal PS
* buffered frames.
*/
for (;;) {
spin_lock_irqsave(&sta->ps_tx_buf[ac].lock, flags);
skb = skb_peek(&sta->ps_tx_buf[ac]);
if (sta_info_buffer_expired(sta, skb))
skb = __skb_dequeue(&sta->ps_tx_buf[ac]);
else
skb = NULL;
spin_unlock_irqrestore(&sta->ps_tx_buf[ac].lock, flags);
/*
* frames are queued in order, so if this one
* hasn't expired yet (or we reached the end of
* the queue) we can stop testing
*/
if (!skb)
break;
local->total_ps_buffered--;
ps_dbg(sta->sdata, "Buffered frame expired (STA %pM)\n",
sta->sta.addr);
ieee80211_free_txskb(&local->hw, skb);
}
/*
* Finally, recalculate the TIM bit for this station -- it might
* now be clear because the station was too slow to retrieve its
* frames.
*/
sta_info_recalc_tim(sta);
/*
* Return whether there are any frames still buffered, this is
* used to check whether the cleanup timer still needs to run,
* if there are no frames we don't need to rearm the timer.
*/
return !(skb_queue_empty(&sta->ps_tx_buf[ac]) &&
skb_queue_empty(&sta->tx_filtered[ac]));
}
static bool sta_info_cleanup_expire_buffered(struct ieee80211_local *local,
struct sta_info *sta)
{
bool have_buffered = false;
int ac;
mac80211: mesh power save basics Add routines to - maintain a PS mode for each peer and a non-peer PS mode - indicate own PS mode in transmitted frames - track neighbor STAs power modes - buffer frames when neighbors are in PS mode - add TIM and Awake Window IE to beacons - release frames in Mesh Peer Service Periods Add local_pm to sta_info to represent the link-specific power mode at this station towards the remote station. When a peer link is established, use the default power mode stored in mesh config. Update the PS status if the peering status of a neighbor changes. Maintain a mesh power mode for non-peer mesh STAs. Set the non-peer power mode to active mode during peering. Authenticated mesh peering is currently not working when either node is configured to be in power save mode. Indicate the current power mode in transmitted frames. Use QoS Nulls to indicate mesh power mode transitions. For performance reasons, calls to the function setting the frame flags are placed in HWMP routing routines, as there the STA pointer is already available. Add peer_pm to sta_info to represent the peer's link-specific power mode towards the local station. Add nonpeer_pm to represent the peer's power mode towards all non-peer stations. Track power modes based on received frames. Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS neighbor counter and group-addressed frame buffer). Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame buffering routines in the tx path. Update num_sta_ps to buffer and release group-addressed frames after DTIM beacons. Announce the awake window duration in beacons if in light or deep sleep mode towards any peer or non-peer. Create a TIM IE similarly to AP mode and add it to mesh beacons. Parse received Awake Window IEs and check TIM IEs for buffered frames. Release frames towards peers in mesh Peer Service Periods. Use the corresponding trigger frames and monitor the MPSP status. Append a QoS Null as trigger frame if neccessary to properly end the MPSP. Currently, in HT channels MPSPs behave imperfectly and show large delay spikes and frame losses. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com> Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31 01:14:08 +08:00
/* This is only necessary for stations on BSS/MBSS interfaces */
if (!sta->sdata->bss &&
!ieee80211_vif_is_mesh(&sta->sdata->vif))
return false;
for (ac = 0; ac < IEEE80211_NUM_ACS; ac++)
have_buffered |=
sta_info_cleanup_expire_buffered_ac(local, sta, ac);
return have_buffered;
}
int __must_check __sta_info_destroy(struct sta_info *sta)
{
struct ieee80211_local *local;
struct ieee80211_sub_if_data *sdata;
int ret;
might_sleep();
if (!sta)
return -ENOENT;
local = sta->local;
sdata = sta->sdata;
lockdep_assert_held(&local->sta_mtx);
/*
* Before removing the station from the driver and
* rate control, it might still start new aggregation
* sessions -- block that to make sure the tear-down
* will be sufficient.
*/
set_sta_flag(sta, WLAN_STA_BLOCK_BA);
ieee80211_sta_tear_down_BA_sessions(sta, AGG_STOP_DESTROY_STA);
ret = sta_info_hash_del(local, sta);
if (ret)
return ret;
list_del_rcu(&sta->list);
/* this always calls synchronize_net() */
ieee80211_free_sta_keys(local, sta);
sta->dead = true;
local->num_sta--;
local->sta_generation++;
if (sdata->vif.type == NL80211_IFTYPE_AP_VLAN)
RCU_INIT_POINTER(sdata->u.vlan.sta, NULL);
while (sta->sta_state > IEEE80211_STA_NONE) {
ret = sta_info_move_state(sta, sta->sta_state - 1);
if (ret) {
WARN_ON_ONCE(1);
break;
}
}
if (sta->uploaded) {
ret = drv_sta_state(local, sdata, sta, IEEE80211_STA_NONE,
IEEE80211_STA_NOTEXIST);
WARN_ON_ONCE(ret != 0);
}
sta_dbg(sdata, "Removed STA %pM\n", sta->sta.addr);
cfg80211_del_sta(sdata->dev, sta->sta.addr, GFP_KERNEL);
rate_control_remove_sta_debugfs(sta);
ieee80211_sta_debugfs_remove(sta);
call_rcu(&sta->rcu_head, free_sta_rcu);
return 0;
}
int sta_info_destroy_addr(struct ieee80211_sub_if_data *sdata, const u8 *addr)
{
struct sta_info *sta;
int ret;
mutex_lock(&sdata->local->sta_mtx);
sta = sta_info_get(sdata, addr);
ret = __sta_info_destroy(sta);
mutex_unlock(&sdata->local->sta_mtx);
return ret;
}
int sta_info_destroy_addr_bss(struct ieee80211_sub_if_data *sdata,
const u8 *addr)
{
struct sta_info *sta;
int ret;
mutex_lock(&sdata->local->sta_mtx);
sta = sta_info_get_bss(sdata, addr);
ret = __sta_info_destroy(sta);
mutex_unlock(&sdata->local->sta_mtx);
return ret;
}
static void sta_info_cleanup(unsigned long data)
{
struct ieee80211_local *local = (struct ieee80211_local *) data;
struct sta_info *sta;
bool timer_needed = false;
rcu_read_lock();
list_for_each_entry_rcu(sta, &local->sta_list, list)
if (sta_info_cleanup_expire_buffered(local, sta))
timer_needed = true;
rcu_read_unlock();
if (local->quiescing)
return;
if (!timer_needed)
return;
mod_timer(&local->sta_cleanup,
round_jiffies(jiffies + STA_INFO_CLEANUP_INTERVAL));
}
void sta_info_init(struct ieee80211_local *local)
{
spin_lock_init(&local->tim_lock);
mutex_init(&local->sta_mtx);
INIT_LIST_HEAD(&local->sta_list);
setup_timer(&local->sta_cleanup, sta_info_cleanup,
(unsigned long)local);
}
void sta_info_stop(struct ieee80211_local *local)
{
del_timer_sync(&local->sta_cleanup);
}
int sta_info_flush_defer(struct ieee80211_sub_if_data *sdata)
{
struct ieee80211_local *local = sdata->local;
struct sta_info *sta, *tmp;
int ret = 0;
might_sleep();
mutex_lock(&local->sta_mtx);
list_for_each_entry_safe(sta, tmp, &local->sta_list, list) {
if (sdata == sta->sdata) {
WARN_ON(__sta_info_destroy(sta));
ret++;
}
}
mutex_unlock(&local->sta_mtx);
return ret;
}
void sta_info_flush_cleanup(struct ieee80211_sub_if_data *sdata)
{
ieee80211_cleanup_sdata_stas(sdata);
cancel_work_sync(&sdata->cleanup_stations_wk);
}
void ieee80211_sta_expire(struct ieee80211_sub_if_data *sdata,
unsigned long exp_time)
{
struct ieee80211_local *local = sdata->local;
struct sta_info *sta, *tmp;
mutex_lock(&local->sta_mtx);
mac80211: fix kernel panic in IBSS due to a regression kernel panic occurs when we create an IBSS mode and leave it for sometime without any joiner and this is introduced by the commit ec2b774e7c91094d8c00de579646f1162b87b01e where we don't put proper braces for 'list_for_each_entry_safe' and we pass an invalid 'sta' pointer to __sta_info_destroy EIP is at __list_add+0xe/0xa0 EAX: f3b63db4 EBX: 00000000 ECX: eab88c1c EDX: 00000000 ESI: 00000000 EDI: 00000246 EBP: f3b63d80 ESP: f3b63d58 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Process kworker/u:2 (pid: 198, ti=f3b62000 task=f3afbea0 task.ti=f3b62000) Stack: 00000000 00000000 f9ef9821 00000000 00000000 eab88c30 f3b63d80 c017f623 eab88bf0 eab88bf0 f3b63dd0 c066f925 00000000 00000002 00000000 f9ef9821 f3b63da0 c0180a2b eab88c1c eab88c30 00000002 f3afbea0 eab88bf4 f3b63db4 Call Trace: [<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<c017f623>] ? debug_mutex_add_waiter+0x23/0x60 [<c066f925>] __mutex_lock_common+0xd5/0x390 [<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<c0180a2b>] ? trace_hardirqs_off+0xb/0x10 [<c066fd37>] mutex_lock_nested+0x47/0x60 [<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<f9ef9821>] __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<f9ef8989>] ieee80211_sta_tear_down_BA_sessions+0x39/0x60 [mac80211] [<f9ef1a67>] __sta_info_destroy+0x57/0x780 [mac80211] [<f9ef2223>] ieee80211_sta_expire+0x93/0xb0 [mac80211] [<f9efc8f6>] ieee80211_ibss_work+0x2d6/0x530 [mac80211] Cc: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-12-26 13:13:29 +08:00
list_for_each_entry_safe(sta, tmp, &local->sta_list, list) {
if (sdata != sta->sdata)
continue;
if (time_after(jiffies, sta->last_rx + exp_time)) {
sta_dbg(sta->sdata, "expiring inactive STA %pM\n",
sta->sta.addr);
mac80211: mesh power save basics Add routines to - maintain a PS mode for each peer and a non-peer PS mode - indicate own PS mode in transmitted frames - track neighbor STAs power modes - buffer frames when neighbors are in PS mode - add TIM and Awake Window IE to beacons - release frames in Mesh Peer Service Periods Add local_pm to sta_info to represent the link-specific power mode at this station towards the remote station. When a peer link is established, use the default power mode stored in mesh config. Update the PS status if the peering status of a neighbor changes. Maintain a mesh power mode for non-peer mesh STAs. Set the non-peer power mode to active mode during peering. Authenticated mesh peering is currently not working when either node is configured to be in power save mode. Indicate the current power mode in transmitted frames. Use QoS Nulls to indicate mesh power mode transitions. For performance reasons, calls to the function setting the frame flags are placed in HWMP routing routines, as there the STA pointer is already available. Add peer_pm to sta_info to represent the peer's link-specific power mode towards the local station. Add nonpeer_pm to represent the peer's power mode towards all non-peer stations. Track power modes based on received frames. Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS neighbor counter and group-addressed frame buffer). Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame buffering routines in the tx path. Update num_sta_ps to buffer and release group-addressed frames after DTIM beacons. Announce the awake window duration in beacons if in light or deep sleep mode towards any peer or non-peer. Create a TIM IE similarly to AP mode and add it to mesh beacons. Parse received Awake Window IEs and check TIM IEs for buffered frames. Release frames towards peers in mesh Peer Service Periods. Use the corresponding trigger frames and monitor the MPSP status. Append a QoS Null as trigger frame if neccessary to properly end the MPSP. Currently, in HT channels MPSPs behave imperfectly and show large delay spikes and frame losses. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com> Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31 01:14:08 +08:00
if (ieee80211_vif_is_mesh(&sdata->vif) &&
test_sta_flag(sta, WLAN_STA_PS_STA))
atomic_dec(&sdata->u.mesh.ps.num_sta_ps);
WARN_ON(__sta_info_destroy(sta));
}
mac80211: fix kernel panic in IBSS due to a regression kernel panic occurs when we create an IBSS mode and leave it for sometime without any joiner and this is introduced by the commit ec2b774e7c91094d8c00de579646f1162b87b01e where we don't put proper braces for 'list_for_each_entry_safe' and we pass an invalid 'sta' pointer to __sta_info_destroy EIP is at __list_add+0xe/0xa0 EAX: f3b63db4 EBX: 00000000 ECX: eab88c1c EDX: 00000000 ESI: 00000000 EDI: 00000246 EBP: f3b63d80 ESP: f3b63d58 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Process kworker/u:2 (pid: 198, ti=f3b62000 task=f3afbea0 task.ti=f3b62000) Stack: 00000000 00000000 f9ef9821 00000000 00000000 eab88c30 f3b63d80 c017f623 eab88bf0 eab88bf0 f3b63dd0 c066f925 00000000 00000002 00000000 f9ef9821 f3b63da0 c0180a2b eab88c1c eab88c30 00000002 f3afbea0 eab88bf4 f3b63db4 Call Trace: [<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<c017f623>] ? debug_mutex_add_waiter+0x23/0x60 [<c066f925>] __mutex_lock_common+0xd5/0x390 [<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<c0180a2b>] ? trace_hardirqs_off+0xb/0x10 [<c066fd37>] mutex_lock_nested+0x47/0x60 [<f9ef9821>] ? __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<f9ef9821>] __ieee80211_stop_tx_ba_session+0x31/0x60 [mac80211] [<f9ef8989>] ieee80211_sta_tear_down_BA_sessions+0x39/0x60 [mac80211] [<f9ef1a67>] __sta_info_destroy+0x57/0x780 [mac80211] [<f9ef2223>] ieee80211_sta_expire+0x93/0xb0 [mac80211] [<f9efc8f6>] ieee80211_ibss_work+0x2d6/0x530 [mac80211] Cc: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-12-26 13:13:29 +08:00
}
mutex_unlock(&local->sta_mtx);
}
struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw,
const u8 *addr,
const u8 *localaddr)
{
struct sta_info *sta, *nxt;
/*
* Just return a random station if localaddr is NULL
* ... first in list.
*/
for_each_sta_info(hw_to_local(hw), addr, sta, nxt) {
if (localaddr &&
!ether_addr_equal(sta->sdata->vif.addr, localaddr))
continue;
if (!sta->uploaded)
return NULL;
return &sta->sta;
}
return NULL;
}
EXPORT_SYMBOL_GPL(ieee80211_find_sta_by_ifaddr);
struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif,
const u8 *addr)
{
struct sta_info *sta;
if (!vif)
return NULL;
sta = sta_info_get_bss(vif_to_sdata(vif), addr);
if (!sta)
return NULL;
if (!sta->uploaded)
return NULL;
return &sta->sta;
}
EXPORT_SYMBOL(ieee80211_find_sta);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
static void clear_sta_ps_flags(void *_sta)
{
struct sta_info *sta = _sta;
struct ieee80211_sub_if_data *sdata = sta->sdata;
struct ps_data *ps;
if (sdata->vif.type == NL80211_IFTYPE_AP ||
sdata->vif.type == NL80211_IFTYPE_AP_VLAN)
ps = &sdata->bss->ps;
mac80211: mesh power save basics Add routines to - maintain a PS mode for each peer and a non-peer PS mode - indicate own PS mode in transmitted frames - track neighbor STAs power modes - buffer frames when neighbors are in PS mode - add TIM and Awake Window IE to beacons - release frames in Mesh Peer Service Periods Add local_pm to sta_info to represent the link-specific power mode at this station towards the remote station. When a peer link is established, use the default power mode stored in mesh config. Update the PS status if the peering status of a neighbor changes. Maintain a mesh power mode for non-peer mesh STAs. Set the non-peer power mode to active mode during peering. Authenticated mesh peering is currently not working when either node is configured to be in power save mode. Indicate the current power mode in transmitted frames. Use QoS Nulls to indicate mesh power mode transitions. For performance reasons, calls to the function setting the frame flags are placed in HWMP routing routines, as there the STA pointer is already available. Add peer_pm to sta_info to represent the peer's link-specific power mode towards the local station. Add nonpeer_pm to represent the peer's power mode towards all non-peer stations. Track power modes based on received frames. Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS neighbor counter and group-addressed frame buffer). Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame buffering routines in the tx path. Update num_sta_ps to buffer and release group-addressed frames after DTIM beacons. Announce the awake window duration in beacons if in light or deep sleep mode towards any peer or non-peer. Create a TIM IE similarly to AP mode and add it to mesh beacons. Parse received Awake Window IEs and check TIM IEs for buffered frames. Release frames towards peers in mesh Peer Service Periods. Use the corresponding trigger frames and monitor the MPSP status. Append a QoS Null as trigger frame if neccessary to properly end the MPSP. Currently, in HT channels MPSPs behave imperfectly and show large delay spikes and frame losses. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com> Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31 01:14:08 +08:00
else if (ieee80211_vif_is_mesh(&sdata->vif))
ps = &sdata->u.mesh.ps;
else
return;
clear_sta_flag(sta, WLAN_STA_PS_DRIVER);
if (test_and_clear_sta_flag(sta, WLAN_STA_PS_STA))
atomic_dec(&ps->num_sta_ps);
}
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
/* powersave support code */
void ieee80211_sta_ps_deliver_wakeup(struct sta_info *sta)
{
struct ieee80211_sub_if_data *sdata = sta->sdata;
struct ieee80211_local *local = sdata->local;
struct sk_buff_head pending;
int filtered = 0, buffered = 0, ac;
unsigned long flags;
clear_sta_flag(sta, WLAN_STA_SP);
BUILD_BUG_ON(BITS_TO_LONGS(IEEE80211_NUM_TIDS) > 1);
sta->driver_buffered_tids = 0;
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
if (!(local->hw.flags & IEEE80211_HW_AP_LINK_PS))
drv_sta_notify(local, sdata, STA_NOTIFY_AWAKE, &sta->sta);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
skb_queue_head_init(&pending);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
/* Send all buffered frames to the station */
for (ac = 0; ac < IEEE80211_NUM_ACS; ac++) {
int count = skb_queue_len(&pending), tmp;
spin_lock_irqsave(&sta->tx_filtered[ac].lock, flags);
skb_queue_splice_tail_init(&sta->tx_filtered[ac], &pending);
spin_unlock_irqrestore(&sta->tx_filtered[ac].lock, flags);
tmp = skb_queue_len(&pending);
filtered += tmp - count;
count = tmp;
spin_lock_irqsave(&sta->ps_tx_buf[ac].lock, flags);
skb_queue_splice_tail_init(&sta->ps_tx_buf[ac], &pending);
spin_unlock_irqrestore(&sta->ps_tx_buf[ac].lock, flags);
tmp = skb_queue_len(&pending);
buffered += tmp - count;
}
ieee80211_add_pending_skbs_fn(local, &pending, clear_sta_ps_flags, sta);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
local->total_ps_buffered -= buffered;
sta_info_recalc_tim(sta);
ps_dbg(sdata,
"STA %pM aid %d sending %d filtered/%d PS frames since STA not sleeping anymore\n",
sta->sta.addr, sta->sta.aid, filtered, buffered);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
}
static void ieee80211_send_null_response(struct ieee80211_sub_if_data *sdata,
struct sta_info *sta, int tid,
enum ieee80211_frame_release_type reason)
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
{
struct ieee80211_local *local = sdata->local;
struct ieee80211_qos_hdr *nullfunc;
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
struct sk_buff *skb;
int size = sizeof(*nullfunc);
__le16 fc;
bool qos = test_sta_flag(sta, WLAN_STA_WME);
struct ieee80211_tx_info *info;
struct ieee80211_chanctx_conf *chanctx_conf;
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
if (qos) {
fc = cpu_to_le16(IEEE80211_FTYPE_DATA |
IEEE80211_STYPE_QOS_NULLFUNC |
IEEE80211_FCTL_FROMDS);
} else {
size -= 2;
fc = cpu_to_le16(IEEE80211_FTYPE_DATA |
IEEE80211_STYPE_NULLFUNC |
IEEE80211_FCTL_FROMDS);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
}
skb = dev_alloc_skb(local->hw.extra_tx_headroom + size);
if (!skb)
return;
skb_reserve(skb, local->hw.extra_tx_headroom);
nullfunc = (void *) skb_put(skb, size);
nullfunc->frame_control = fc;
nullfunc->duration_id = 0;
memcpy(nullfunc->addr1, sta->sta.addr, ETH_ALEN);
memcpy(nullfunc->addr2, sdata->vif.addr, ETH_ALEN);
memcpy(nullfunc->addr3, sdata->vif.addr, ETH_ALEN);
skb->priority = tid;
skb_set_queue_mapping(skb, ieee802_1d_to_ac[tid]);
if (qos) {
nullfunc->qos_ctrl = cpu_to_le16(tid);
if (reason == IEEE80211_FRAME_RELEASE_UAPSD)
nullfunc->qos_ctrl |=
cpu_to_le16(IEEE80211_QOS_CTL_EOSP);
}
info = IEEE80211_SKB_CB(skb);
/*
* Tell TX path to send this frame even though the
* STA may still remain is PS mode after this frame
* exchange. Also set EOSP to indicate this packet
* ends the poll/service period.
*/
info->flags |= IEEE80211_TX_CTL_NO_PS_BUFFER |
IEEE80211_TX_CTL_PS_RESPONSE |
IEEE80211_TX_STATUS_EOSP |
IEEE80211_TX_CTL_REQ_TX_STATUS;
drv_allow_buffered_frames(local, sta, BIT(tid), 1, reason, false);
skb->dev = sdata->dev;
rcu_read_lock();
chanctx_conf = rcu_dereference(sdata->vif.chanctx_conf);
if (WARN_ON(!chanctx_conf)) {
rcu_read_unlock();
kfree_skb(skb);
return;
}
ieee80211_xmit(sdata, skb, chanctx_conf->def.chan->band);
rcu_read_unlock();
}
static void
ieee80211_sta_ps_deliver_response(struct sta_info *sta,
int n_frames, u8 ignored_acs,
enum ieee80211_frame_release_type reason)
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
{
struct ieee80211_sub_if_data *sdata = sta->sdata;
struct ieee80211_local *local = sdata->local;
bool found = false;
bool more_data = false;
int ac;
unsigned long driver_release_tids = 0;
struct sk_buff_head frames;
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
/* Service or PS-Poll period starts */
set_sta_flag(sta, WLAN_STA_SP);
__skb_queue_head_init(&frames);
/*
* Get response frame(s) and more data bit for it.
*/
for (ac = 0; ac < IEEE80211_NUM_ACS; ac++) {
unsigned long tids;
if (ignored_acs & BIT(ac))
continue;
tids = ieee80211_tids_for_ac(ac);
if (!found) {
driver_release_tids = sta->driver_buffered_tids & tids;
if (driver_release_tids) {
found = true;
} else {
struct sk_buff *skb;
while (n_frames > 0) {
skb = skb_dequeue(&sta->tx_filtered[ac]);
if (!skb) {
skb = skb_dequeue(
&sta->ps_tx_buf[ac]);
if (skb)
local->total_ps_buffered--;
}
if (!skb)
break;
n_frames--;
found = true;
__skb_queue_tail(&frames, skb);
}
}
/*
* If the driver has data on more than one TID then
* certainly there's more data if we release just a
* single frame now (from a single TID).
*/
if (reason == IEEE80211_FRAME_RELEASE_PSPOLL &&
hweight16(driver_release_tids) > 1) {
more_data = true;
driver_release_tids =
BIT(ffs(driver_release_tids) - 1);
break;
}
}
if (!skb_queue_empty(&sta->tx_filtered[ac]) ||
!skb_queue_empty(&sta->ps_tx_buf[ac])) {
more_data = true;
break;
}
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
}
if (!found) {
int tid;
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
/*
* For PS-Poll, this can only happen due to a race condition
* when we set the TIM bit and the station notices it, but
* before it can poll for the frame we expire it.
*
* For uAPSD, this is said in the standard (11.2.1.5 h):
* At each unscheduled SP for a non-AP STA, the AP shall
* attempt to transmit at least one MSDU or MMPDU, but no
* more than the value specified in the Max SP Length field
* in the QoS Capability element from delivery-enabled ACs,
* that are destined for the non-AP STA.
*
* Since we have no other MSDU/MMPDU, transmit a QoS null frame.
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
*/
/* This will evaluate to 1, 3, 5 or 7. */
tid = 7 - ((ffs(~ignored_acs) - 1) << 1);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
ieee80211_send_null_response(sdata, sta, tid, reason);
return;
}
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
if (!driver_release_tids) {
struct sk_buff_head pending;
struct sk_buff *skb;
int num = 0;
u16 tids = 0;
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
skb_queue_head_init(&pending);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
while ((skb = __skb_dequeue(&frames))) {
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
struct ieee80211_hdr *hdr = (void *) skb->data;
u8 *qoshdr = NULL;
num++;
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
/*
* Tell TX path to send this frame even though the
* STA may still remain is PS mode after this frame
* exchange.
*/
info->flags |= IEEE80211_TX_CTL_NO_PS_BUFFER |
IEEE80211_TX_CTL_PS_RESPONSE;
/*
* Use MoreData flag to indicate whether there are
* more buffered frames for this STA
*/
if (more_data || !skb_queue_empty(&frames))
hdr->frame_control |=
cpu_to_le16(IEEE80211_FCTL_MOREDATA);
else
hdr->frame_control &=
cpu_to_le16(~IEEE80211_FCTL_MOREDATA);
if (ieee80211_is_data_qos(hdr->frame_control) ||
ieee80211_is_qos_nullfunc(hdr->frame_control))
qoshdr = ieee80211_get_qos_ctl(hdr);
/* end service period after last frame */
if (skb_queue_empty(&frames)) {
if (reason == IEEE80211_FRAME_RELEASE_UAPSD &&
qoshdr)
*qoshdr |= IEEE80211_QOS_CTL_EOSP;
info->flags |= IEEE80211_TX_STATUS_EOSP |
IEEE80211_TX_CTL_REQ_TX_STATUS;
}
if (qoshdr)
tids |= BIT(*qoshdr & IEEE80211_QOS_CTL_TID_MASK);
else
tids |= BIT(0);
__skb_queue_tail(&pending, skb);
}
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
drv_allow_buffered_frames(local, sta, tids, num,
reason, more_data);
ieee80211_add_pending_skbs(local, &pending);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
sta_info_recalc_tim(sta);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
} else {
/*
* We need to release a frame that is buffered somewhere in the
* driver ... it'll have to handle that.
* Note that, as per the comment above, it'll also have to see
* if there is more than just one frame on the specific TID that
* we're releasing from, and it needs to set the more-data bit
* accordingly if we tell it that there's no more data. If we do
* tell it there's more data, then of course the more-data bit
* needs to be set anyway.
*/
drv_release_buffered_frames(local, sta, driver_release_tids,
n_frames, reason, more_data);
/*
* Note that we don't recalculate the TIM bit here as it would
* most likely have no effect at all unless the driver told us
* that the TID became empty before returning here from the
* release function.
* Either way, however, when the driver tells us that the TID
* became empty we'll do the TIM recalculation.
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
*/
}
}
void ieee80211_sta_ps_deliver_poll_response(struct sta_info *sta)
{
u8 ignore_for_response = sta->sta.uapsd_queues;
/*
* If all ACs are delivery-enabled then we should reply
* from any of them, if only some are enabled we reply
* only from the non-enabled ones.
*/
if (ignore_for_response == BIT(IEEE80211_NUM_ACS) - 1)
ignore_for_response = 0;
ieee80211_sta_ps_deliver_response(sta, 1, ignore_for_response,
IEEE80211_FRAME_RELEASE_PSPOLL);
}
void ieee80211_sta_ps_deliver_uapsd(struct sta_info *sta)
{
int n_frames = sta->sta.max_sp;
u8 delivery_enabled = sta->sta.uapsd_queues;
/*
* If we ever grow support for TSPEC this might happen if
* the TSPEC update from hostapd comes in between a trigger
* frame setting WLAN_STA_UAPSD in the RX path and this
* actually getting called.
*/
if (!delivery_enabled)
return;
switch (sta->sta.max_sp) {
case 1:
n_frames = 2;
break;
case 2:
n_frames = 4;
break;
case 3:
n_frames = 6;
break;
case 0:
/* XXX: what is a good value? */
n_frames = 8;
break;
}
ieee80211_sta_ps_deliver_response(sta, n_frames, ~delivery_enabled,
IEEE80211_FRAME_RELEASE_UAPSD);
}
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
void ieee80211_sta_block_awake(struct ieee80211_hw *hw,
struct ieee80211_sta *pubsta, bool block)
{
struct sta_info *sta = container_of(pubsta, struct sta_info, sta);
trace_api_sta_block_awake(sta->local, pubsta, block);
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
if (block)
set_sta_flag(sta, WLAN_STA_PS_DRIVER);
else if (test_sta_flag(sta, WLAN_STA_PS_DRIVER))
mac80211: async station powersave handling Some devices require that all frames to a station are flushed when that station goes into powersave mode before being able to send frames to that station again when it wakes up or polls -- all in order to avoid reordering and too many or too few frames being sent to the station when it polls. Normally, this is the case unless the station goes to sleep and wakes up very quickly again. But in that case, frames for it may be pending on the hardware queues, and thus races could happen in the case of multiple hardware queues used for QoS/WMM. Normally this isn't a problem, but with the iwlwifi mechanism we need to make sure the race doesn't happen. This makes mac80211 able to cope with the race with driver help by a new WLAN_STA_PS_DRIVER per-station flag that can be controlled by the driver and tells mac80211 whether it can transmit frames or not. This flag must be set according to very specific rules outlined in the documentation for the function that controls it. When we buffer new frames for the station, we normally set the TIM bit right away, but while the driver has blocked transmission to that sta we need to avoid that as well since we cannot respond to the station if it wakes up due to the TIM bit. Once the driver unblocks, we can set the TIM bit. Similarly, when the station just wakes up, we need to wait until all other frames are flushed before we can transmit frames to that station, so the same applies here, we need to wait for the driver to give the OK. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-06 18:35:50 +08:00
ieee80211_queue_work(hw, &sta->drv_unblock_wk);
}
EXPORT_SYMBOL(ieee80211_sta_block_awake);
void ieee80211_sta_eosp(struct ieee80211_sta *pubsta)
{
struct sta_info *sta = container_of(pubsta, struct sta_info, sta);
struct ieee80211_local *local = sta->local;
trace_api_eosp(local, pubsta);
clear_sta_flag(sta, WLAN_STA_SP);
}
EXPORT_SYMBOL(ieee80211_sta_eosp);
void ieee80211_sta_set_buffered(struct ieee80211_sta *pubsta,
u8 tid, bool buffered)
{
struct sta_info *sta = container_of(pubsta, struct sta_info, sta);
if (WARN_ON(tid >= IEEE80211_NUM_TIDS))
return;
if (buffered)
set_bit(tid, &sta->driver_buffered_tids);
else
clear_bit(tid, &sta->driver_buffered_tids);
sta_info_recalc_tim(sta);
}
EXPORT_SYMBOL(ieee80211_sta_set_buffered);
int sta_info_move_state(struct sta_info *sta,
enum ieee80211_sta_state new_state)
{
might_sleep();
if (sta->sta_state == new_state)
return 0;
/* check allowed transitions first */
switch (new_state) {
case IEEE80211_STA_NONE:
if (sta->sta_state != IEEE80211_STA_AUTH)
return -EINVAL;
break;
case IEEE80211_STA_AUTH:
if (sta->sta_state != IEEE80211_STA_NONE &&
sta->sta_state != IEEE80211_STA_ASSOC)
return -EINVAL;
break;
case IEEE80211_STA_ASSOC:
if (sta->sta_state != IEEE80211_STA_AUTH &&
sta->sta_state != IEEE80211_STA_AUTHORIZED)
return -EINVAL;
break;
case IEEE80211_STA_AUTHORIZED:
if (sta->sta_state != IEEE80211_STA_ASSOC)
return -EINVAL;
break;
default:
WARN(1, "invalid state %d", new_state);
return -EINVAL;
}
sta_dbg(sta->sdata, "moving STA %pM to state %d\n",
sta->sta.addr, new_state);
/*
* notify the driver before the actual changes so it can
* fail the transition
*/
if (test_sta_flag(sta, WLAN_STA_INSERTED)) {
int err = drv_sta_state(sta->local, sta->sdata, sta,
sta->sta_state, new_state);
if (err)
return err;
}
/* reflect the change in all state variables */
switch (new_state) {
case IEEE80211_STA_NONE:
if (sta->sta_state == IEEE80211_STA_AUTH)
clear_bit(WLAN_STA_AUTH, &sta->_flags);
break;
case IEEE80211_STA_AUTH:
if (sta->sta_state == IEEE80211_STA_NONE)
set_bit(WLAN_STA_AUTH, &sta->_flags);
else if (sta->sta_state == IEEE80211_STA_ASSOC)
clear_bit(WLAN_STA_ASSOC, &sta->_flags);
break;
case IEEE80211_STA_ASSOC:
if (sta->sta_state == IEEE80211_STA_AUTH) {
set_bit(WLAN_STA_ASSOC, &sta->_flags);
} else if (sta->sta_state == IEEE80211_STA_AUTHORIZED) {
if (sta->sdata->vif.type == NL80211_IFTYPE_AP ||
(sta->sdata->vif.type == NL80211_IFTYPE_AP_VLAN &&
!sta->sdata->u.vlan.sta))
atomic_dec(&sta->sdata->bss->num_mcast_sta);
clear_bit(WLAN_STA_AUTHORIZED, &sta->_flags);
}
break;
case IEEE80211_STA_AUTHORIZED:
if (sta->sta_state == IEEE80211_STA_ASSOC) {
if (sta->sdata->vif.type == NL80211_IFTYPE_AP ||
(sta->sdata->vif.type == NL80211_IFTYPE_AP_VLAN &&
!sta->sdata->u.vlan.sta))
atomic_inc(&sta->sdata->bss->num_mcast_sta);
set_bit(WLAN_STA_AUTHORIZED, &sta->_flags);
}
break;
default:
break;
}
sta->sta_state = new_state;
return 0;
}