p71924506
/
linux_old1
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
linux_old1/drivers/phy/phy-rockchip-emmc.c

384 lines
11 KiB
C
Raw Normal View History

phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
/*
* Rockchip emmc PHY driver
*
* Copyright (C) 2016 Shawn Lin <shawn.lin@rock-chips.com>
* Copyright (C) 2016 ROCKCHIP, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
#include <linux/clk.h>
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
#include <linux/delay.h>
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
/*
* The higher 16-bit of this register is used for write protection
* only if BIT(x + 16) set to 1 the BIT(x) can be written.
*/
#define HIWORD_UPDATE(val, mask, shift) \
((val) << (shift) | (mask) << ((shift) + 16))
/* Register definition */
phy: rockchip-emmc: reindent the register definitions Some of the spacing was wrong (spaces instead of tabs), and due to longer entries added later, the columns weren't aligned. Let's get everything consistent. Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:43 +08:00
#define GRF_EMMCPHY_CON0 0x0
#define GRF_EMMCPHY_CON1 0x4
#define GRF_EMMCPHY_CON2 0x8
#define GRF_EMMCPHY_CON3 0xc
#define GRF_EMMCPHY_CON4 0x10
#define GRF_EMMCPHY_CON5 0x14
#define GRF_EMMCPHY_CON6 0x18
#define GRF_EMMCPHY_STATUS 0x20
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
phy: rockchip-emmc: reindent the register definitions Some of the spacing was wrong (spaces instead of tabs), and due to longer entries added later, the columns weren't aligned. Let's get everything consistent. Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:43 +08:00
#define PHYCTRL_PDB_MASK 0x1
#define PHYCTRL_PDB_SHIFT 0x0
#define PHYCTRL_PDB_PWR_ON 0x1
#define PHYCTRL_PDB_PWR_OFF 0x0
#define PHYCTRL_ENDLL_MASK 0x1
#define PHYCTRL_ENDLL_SHIFT 0x1
#define PHYCTRL_ENDLL_ENABLE 0x1
#define PHYCTRL_ENDLL_DISABLE 0x0
#define PHYCTRL_CALDONE_MASK 0x1
#define PHYCTRL_CALDONE_SHIFT 0x6
#define PHYCTRL_CALDONE_DONE 0x1
#define PHYCTRL_CALDONE_GOING 0x0
#define PHYCTRL_DLLRDY_MASK 0x1
#define PHYCTRL_DLLRDY_SHIFT 0x5
#define PHYCTRL_DLLRDY_DONE 0x1
#define PHYCTRL_DLLRDY_GOING 0x0
#define PHYCTRL_FREQSEL_200M 0x0
#define PHYCTRL_FREQSEL_50M 0x1
#define PHYCTRL_FREQSEL_100M 0x2
#define PHYCTRL_FREQSEL_150M 0x3
#define PHYCTRL_FREQSEL_MASK 0x3
#define PHYCTRL_FREQSEL_SHIFT 0xc
#define PHYCTRL_DR_MASK 0x7
#define PHYCTRL_DR_SHIFT 0x4
#define PHYCTRL_DR_50OHM 0x0
#define PHYCTRL_DR_33OHM 0x1
#define PHYCTRL_DR_66OHM 0x2
#define PHYCTRL_DR_100OHM 0x3
#define PHYCTRL_DR_40OHM 0x4
phy: rockchip-emmc: configure default output tap delay The output tap delay controls helps maintain the hold requirements for eMMC. The exact value is dependent on the SoC and other factors, though it isn't really an exact science. But the default of 0 is not very good, as it doesn't give the eMMC much hold time, so let's bump up to 4 (approx 90 degree phase?). If we need to configure this any further (e.g., based on board or speed factors), we may need to consider a device tree representation. Suggested-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:42 +08:00
#define PHYCTRL_OTAPDLYENA 0x1
#define PHYCTRL_OTAPDLYENA_MASK 0x1
#define PHYCTRL_OTAPDLYENA_SHIFT 0xb
#define PHYCTRL_OTAPDLYSEL_MASK 0xf
#define PHYCTRL_OTAPDLYSEL_SHIFT 0x7
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
struct rockchip_emmc_phy {
unsigned int reg_offset;
struct regmap *reg_base;
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
struct clk *emmcclk;
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
};
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
static int rockchip_emmc_phy_power(struct phy *phy, bool on_off)
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
{
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
unsigned int caldone;
unsigned int dllrdy;
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
unsigned int freqsel = PHYCTRL_FREQSEL_200M;
phy: rockchip-emmc: Be tolerant to card clock of 0 in power on It's possible that there are some reasons to turn the PHY on while the clock is 0. In this case we just won't wait for the DLL to lock. This is a bit of a stopgap until we figure out exactly when we're supposed to wait for the DLL to lock and when we're supposed to power cycle the PHY. Note: this patch should help with suspend/resume where the system will try to turn the PHY back on when the clock is 0. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-28 01:39:26 +08:00
unsigned long rate;
phy: rockchip-emmc: Increase lock time allowance Previous PHY code waited a fixed amount of time for the DLL to lock at power on time. Unfortunately, the time for the DLL to lock is actually a bit more dynamic and can be longer if the card clock is slower. Instead of waiting a fixed 30 us, let's now dynamically wait until the lock bit gets set. We'll wait up to 10 ms which should be OK even if the card clock is at the super slow 100 kHz. On its own, this change makes the PHY power on code a little more robust. Before this change the PHY was relying on the eMMC code to make sure the PHY was only powered on when the card clock was set to at least 50 MHz before, though this reliance wasn't documented anywhere. This change will be even more useful in future changes where we actually need to be able to wait for a DLL lock at slower clock speeds. Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:44 +08:00
unsigned long timeout;
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
phy: rockchip-emmc: Be tolerant to card clock of 0 in power on It's possible that there are some reasons to turn the PHY on while the clock is 0. In this case we just won't wait for the DLL to lock. This is a bit of a stopgap until we figure out exactly when we're supposed to wait for the DLL to lock and when we're supposed to power cycle the PHY. Note: this patch should help with suspend/resume where the system will try to turn the PHY back on when the clock is 0. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-28 01:39:26 +08:00
/*
* Keep phyctrl_pdb and phyctrl_endll low to allow
* initialization of CALIO state M/C DFFs
*/
regmap_write(rk_phy->reg_base,
rk_phy->reg_offset + GRF_EMMCPHY_CON6,
HIWORD_UPDATE(PHYCTRL_PDB_PWR_OFF,
PHYCTRL_PDB_MASK,
PHYCTRL_PDB_SHIFT));
regmap_write(rk_phy->reg_base,
rk_phy->reg_offset + GRF_EMMCPHY_CON6,
HIWORD_UPDATE(PHYCTRL_ENDLL_DISABLE,
PHYCTRL_ENDLL_MASK,
PHYCTRL_ENDLL_SHIFT));
/* Already finish power_off above */
if (on_off == PHYCTRL_PDB_PWR_OFF)
return 0;
rate = clk_get_rate(rk_phy->emmcclk);
if (rate != 0) {
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
unsigned long ideal_rate;
unsigned long diff;
switch (rate) {
phy: rockchip-emmc: Be tolerant to card clock of 0 in power on It's possible that there are some reasons to turn the PHY on while the clock is 0. In this case we just won't wait for the DLL to lock. This is a bit of a stopgap until we figure out exactly when we're supposed to wait for the DLL to lock and when we're supposed to power cycle the PHY. Note: this patch should help with suspend/resume where the system will try to turn the PHY back on when the clock is 0. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-28 01:39:26 +08:00
case 1 ... 74999999:
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
ideal_rate = 50000000;
freqsel = PHYCTRL_FREQSEL_50M;
break;
case 75000000 ... 124999999:
ideal_rate = 100000000;
freqsel = PHYCTRL_FREQSEL_100M;
break;
case 125000000 ... 174999999:
ideal_rate = 150000000;
freqsel = PHYCTRL_FREQSEL_150M;
break;
default:
ideal_rate = 200000000;
break;
phy: fix semicolon.cocci warnings Remove unneeded semicolon. Generated by: coccinellery/semicolon/semicolon.cocci Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> Cc: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-10-20 14:53:38 +08:00
}
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
diff = (rate > ideal_rate) ?
rate - ideal_rate : ideal_rate - rate;
/*
* In order for tuning delays to be accurate we need to be
* pretty spot on for the DLL range, so warn if we're too
* far off. Also warn if we're above the 200 MHz max. Don't
* warn for really slow rates since we won't be tuning then.
*/
if ((rate > 50000000 && diff > 15000000) || (rate > 200000000))
dev_warn(&phy->dev, "Unsupported rate: %lu\n", rate);
}
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
/*
* According to the user manual, calpad calibration
* cycle takes more than 2us without the minimal recommended
* value, so we may need a little margin here
*/
udelay(3);
regmap_write(rk_phy->reg_base,
rk_phy->reg_offset + GRF_EMMCPHY_CON6,
HIWORD_UPDATE(PHYCTRL_PDB_PWR_ON,
PHYCTRL_PDB_MASK,
PHYCTRL_PDB_SHIFT));
/*
* According to the user manual, it asks driver to
* wait 5us for calpad busy trimming
*/
udelay(5);
regmap_read(rk_phy->reg_base,
rk_phy->reg_offset + GRF_EMMCPHY_STATUS,
&caldone);
caldone = (caldone >> PHYCTRL_CALDONE_SHIFT) & PHYCTRL_CALDONE_MASK;
if (caldone != PHYCTRL_CALDONE_DONE) {
pr_err("rockchip_emmc_phy_power: caldone timeout.\n");
return -ETIMEDOUT;
}
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
/* Set the frequency of the DLL operation */
regmap_write(rk_phy->reg_base,
rk_phy->reg_offset + GRF_EMMCPHY_CON0,
HIWORD_UPDATE(freqsel, PHYCTRL_FREQSEL_MASK,
PHYCTRL_FREQSEL_SHIFT));
/* Turn on the DLL */
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
regmap_write(rk_phy->reg_base,
rk_phy->reg_offset + GRF_EMMCPHY_CON6,
HIWORD_UPDATE(PHYCTRL_ENDLL_ENABLE,
PHYCTRL_ENDLL_MASK,
PHYCTRL_ENDLL_SHIFT));
phy: rockchip-emmc: Be tolerant to card clock of 0 in power on It's possible that there are some reasons to turn the PHY on while the clock is 0. In this case we just won't wait for the DLL to lock. This is a bit of a stopgap until we figure out exactly when we're supposed to wait for the DLL to lock and when we're supposed to power cycle the PHY. Note: this patch should help with suspend/resume where the system will try to turn the PHY back on when the clock is 0. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-28 01:39:26 +08:00
/*
* We turned on the DLL even though the rate was 0 because we the
* clock might be turned on later. ...but we can't wait for the DLL
* to lock when the rate is 0 because it will never lock with no
* input clock.
*
* Technically we should be checking the lock later when the clock
* is turned on, but for now we won't.
*/
if (rate == 0)
return 0;
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
/*
phy: rockchip-emmc: Increase lock time allowance Previous PHY code waited a fixed amount of time for the DLL to lock at power on time. Unfortunately, the time for the DLL to lock is actually a bit more dynamic and can be longer if the card clock is slower. Instead of waiting a fixed 30 us, let's now dynamically wait until the lock bit gets set. We'll wait up to 10 ms which should be OK even if the card clock is at the super slow 100 kHz. On its own, this change makes the PHY power on code a little more robust. Before this change the PHY was relying on the eMMC code to make sure the PHY was only powered on when the card clock was set to at least 50 MHz before, though this reliance wasn't documented anywhere. This change will be even more useful in future changes where we actually need to be able to wait for a DLL lock at slower clock speeds. Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:44 +08:00
* After enabling analog DLL circuits docs say that we need 10.2 us if
* our source clock is at 50 MHz and that lock time scales linearly
* with clock speed. If we are powering on the PHY and the card clock
* is super slow (like 100 kHZ) this could take as long as 5.1 ms as
* per the math: 10.2 us * (50000000 Hz / 100000 Hz) => 5.1 ms
* Hopefully we won't be running at 100 kHz, but we should still make
* sure we wait long enough.
phy: rockchip-emmc: Wait even longer for the DLL to lock Two times out of 2000 reboots I ran into the error message "rockchip_emmc_phy_power: dllrdy timeout". Presumably there is some corner case where the DLL just takes a little longer to timeout. Let's give it even more time to handle these corner cases. Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-28 01:39:27 +08:00
*
* NOTE: There appear to be corner cases where the DLL seems to take
* extra long to lock for reasons that aren't understood. In some
* extreme cases we've seen it take up to over 10ms (!). We'll be
* generous and give it 50ms. We still busy wait here because:
* - In most cases it should be super fast.
* - This is not called lots during normal operation so it shouldn't
* be a power or performance problem to busy wait. We expect it
* only at boot / resume. In both cases, eMMC is probably on the
* critical path so busy waiting a little extra time should be OK.
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
*/
phy: rockchip-emmc: Wait even longer for the DLL to lock Two times out of 2000 reboots I ran into the error message "rockchip_emmc_phy_power: dllrdy timeout". Presumably there is some corner case where the DLL just takes a little longer to timeout. Let's give it even more time to handle these corner cases. Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-28 01:39:27 +08:00
timeout = jiffies + msecs_to_jiffies(50);
phy: rockchip-emmc: Increase lock time allowance Previous PHY code waited a fixed amount of time for the DLL to lock at power on time. Unfortunately, the time for the DLL to lock is actually a bit more dynamic and can be longer if the card clock is slower. Instead of waiting a fixed 30 us, let's now dynamically wait until the lock bit gets set. We'll wait up to 10 ms which should be OK even if the card clock is at the super slow 100 kHz. On its own, this change makes the PHY power on code a little more robust. Before this change the PHY was relying on the eMMC code to make sure the PHY was only powered on when the card clock was set to at least 50 MHz before, though this reliance wasn't documented anywhere. This change will be even more useful in future changes where we actually need to be able to wait for a DLL lock at slower clock speeds. Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:44 +08:00
do {
udelay(1);
regmap_read(rk_phy->reg_base,
rk_phy->reg_offset + GRF_EMMCPHY_STATUS,
&dllrdy);
dllrdy = (dllrdy >> PHYCTRL_DLLRDY_SHIFT) & PHYCTRL_DLLRDY_MASK;
if (dllrdy == PHYCTRL_DLLRDY_DONE)
break;
} while (!time_after(jiffies, timeout));
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
if (dllrdy != PHYCTRL_DLLRDY_DONE) {
pr_err("rockchip_emmc_phy_power: dllrdy timeout.\n");
return -ETIMEDOUT;
}
return 0;
}
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
static int rockchip_emmc_phy_init(struct phy *phy)
{
struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
int ret = 0;
/*
* We purposely get the clock here and not in probe to avoid the
* circular dependency problem. We expect:
* - PHY driver to probe
* - SDHCI driver to start probe
* - SDHCI driver to register it's clock
* - SDHCI driver to get the PHY
* - SDHCI driver to init the PHY
*
* The clock is optional, so upon any error we just set to NULL.
*
* NOTE: we don't do anything special for EPROBE_DEFER here. Given the
* above expected use case, EPROBE_DEFER isn't sensible to expect, so
* it's just like any other error.
*/
rk_phy->emmcclk = clk_get(&phy->dev, "emmcclk");
if (IS_ERR(rk_phy->emmcclk)) {
dev_dbg(&phy->dev, "Error getting emmcclk: %d\n", ret);
rk_phy->emmcclk = NULL;
}
return ret;
}
static int rockchip_emmc_phy_exit(struct phy *phy)
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
{
struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
clk_put(rk_phy->emmcclk);
return 0;
}
static int rockchip_emmc_phy_power_off(struct phy *phy)
{
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
/* Power down emmc phy analog blocks */
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
return rockchip_emmc_phy_power(phy, PHYCTRL_PDB_PWR_OFF);
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
}
static int rockchip_emmc_phy_power_on(struct phy *phy)
{
struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
phy: rockchip-emmc: configure frequency range and drive impedance Signal integrity analysis has suggested we set these values. Do this in power_on(), so that they get reconfigured after suspend/resume. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:41 +08:00
/* Drive impedance: 50 Ohm */
regmap_write(rk_phy->reg_base,
rk_phy->reg_offset + GRF_EMMCPHY_CON6,
HIWORD_UPDATE(PHYCTRL_DR_50OHM,
PHYCTRL_DR_MASK,
PHYCTRL_DR_SHIFT));
phy: rockchip-emmc: configure default output tap delay The output tap delay controls helps maintain the hold requirements for eMMC. The exact value is dependent on the SoC and other factors, though it isn't really an exact science. But the default of 0 is not very good, as it doesn't give the eMMC much hold time, so let's bump up to 4 (approx 90 degree phase?). If we need to configure this any further (e.g., based on board or speed factors), we may need to consider a device tree representation. Suggested-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:42 +08:00
/* Output tap delay: enable */
regmap_write(rk_phy->reg_base,
rk_phy->reg_offset + GRF_EMMCPHY_CON0,
HIWORD_UPDATE(PHYCTRL_OTAPDLYENA,
PHYCTRL_OTAPDLYENA_MASK,
PHYCTRL_OTAPDLYENA_SHIFT));
/* Output tap delay */
regmap_write(rk_phy->reg_base,
rk_phy->reg_offset + GRF_EMMCPHY_CON0,
HIWORD_UPDATE(4,
PHYCTRL_OTAPDLYSEL_MASK,
PHYCTRL_OTAPDLYSEL_SHIFT));
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
/* Power up emmc phy analog blocks */
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
return rockchip_emmc_phy_power(phy, PHYCTRL_PDB_PWR_ON);
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
}
static const struct phy_ops ops = {
phy: rockchip-emmc: Set phyctrl_frqsel based on card clock The "phyctrl_frqsel" is described in the Arasan datasheet [1] as "the frequency range of DLL operation". Although the Rockchip variant of this PHY has different ranges than the reference Arasan PHY it appears as if the functionality is similar. We should set this phyctrl field properly. Note: as per Rockchip engineers, apparently the "phyctrl_frqsel" is actually only useful in HS200 / HS400 modes even though the DLL itself it used for some purposes in all modes. See the discussion in the earlier change in this series: ("mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes"). In any case, it shouldn't hurt to set this always. Note that this change should allow boards to run at HS200 / HS400 speed modes while running at 100 MHz or 150 MHz. In fact, running HS400 at 150 MHz (giving 300 MB/s) is the main motivation of this series, since performance is still good but signal integrity problems are less prevelant at 150 MHz. [1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-21 01:56:53 +08:00
.init = rockchip_emmc_phy_init,
.exit = rockchip_emmc_phy_exit,
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
.power_on = rockchip_emmc_phy_power_on,
.power_off = rockchip_emmc_phy_power_off,
.owner = THIS_MODULE,
};
static int rockchip_emmc_phy_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct rockchip_emmc_phy *rk_phy;
struct phy *generic_phy;
struct phy_provider *phy_provider;
struct regmap *grf;
unsigned int reg_offset;
phy: rockchip-emmc: should be a child device of the GRF The emmc-phy is fully enclosed in the general register files (GRF). Therefore as seen from the device-tree it shouldn't be a separate platform- device but instead a sub-device of the GRF - using the simply-mfd mechanism. The driver entered the kernel in the current merge-window, so we can still adapt the binding without needing a fallback, as the binding hasn't been released with a full kernel yet. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-03-25 05:29:02 +08:00
if (!dev->parent || !dev->parent->of_node)
return -ENODEV;
grf = syscon_node_to_regmap(dev->parent->of_node);
phy: add a driver for the Rockchip SoC internal eMMC PHY This patch to add a generic PHY driver for ROCKCHIP eMMC PHY. Access the PHY via registers provided by GRF (general register files) module. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2016-02-03 15:22:22 +08:00
if (IS_ERR(grf)) {
dev_err(dev, "Missing rockchip,grf property\n");
return PTR_ERR(grf);
}
rk_phy = devm_kzalloc(dev, sizeof(*rk_phy), GFP_KERNEL);
if (!rk_phy)
return -ENOMEM;
if (of_property_read_u32(dev->of_node, "reg", &reg_offset)) {
dev_err(dev, "missing reg property in node %s\n",
dev->of_node->name);
return -EINVAL;
}
rk_phy->reg_offset = reg_offset;
rk_phy->reg_base = grf;
generic_phy = devm_phy_create(dev, dev->of_node, &ops);
if (IS_ERR(generic_phy)) {
dev_err(dev, "failed to create PHY\n");
return PTR_ERR(generic_phy);
}
phy_set_drvdata(generic_phy, rk_phy);
phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
return PTR_ERR_OR_ZERO(phy_provider);
}
static const struct of_device_id rockchip_emmc_phy_dt_ids[] = {
{ .compatible = "rockchip,rk3399-emmc-phy" },
{}
};
MODULE_DEVICE_TABLE(of, rockchip_emmc_phy_dt_ids);
static struct platform_driver rockchip_emmc_driver = {
.probe = rockchip_emmc_phy_probe,
.driver = {
.name = "rockchip-emmc-phy",
.of_match_table = rockchip_emmc_phy_dt_ids,
},
};
module_platform_driver(rockchip_emmc_driver);
MODULE_AUTHOR("Shawn Lin <shawn.lin@rock-chips.com>");
MODULE_DESCRIPTION("Rockchip EMMC PHY driver");
MODULE_LICENSE("GPL v2");