linux_old1/drivers/mmc/host/au1xmmc.c

/*
 * linux/drivers/mmc/host/au1xmmc.c - AU1XX0 MMC driver
 *
 *  Copyright (c) 2005, Advanced Micro Devices, Inc.
 *
 *  Developed with help from the 2.4.30 MMC AU1XXX controller including
 *  the following copyright notices:
 *     Copyright (c) 2003-2004 Embedded Edge, LLC.
 *     Portions Copyright (C) 2002 Embedix, Inc
 *     Copyright 2002 Hewlett-Packard Company

 *  2.6 version of this driver inspired by:
 *     (drivers/mmc/wbsd.c) Copyright (C) 2004-2005 Pierre Ossman,
 *     All Rights Reserved.
 *     (drivers/mmc/pxa.c) Copyright (C) 2003 Russell King,
 *     All Rights Reserved.
 *

 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

/* Why don't we use the SD controllers' carddetect feature?
 *
 * From the AU1100 MMC application guide:
 * If the Au1100-based design is intended to support both MultiMediaCards
 * and 1- or 4-data bit SecureDigital cards, then the solution is to
 * connect a weak (560KOhm) pull-up resistor to connector pin 1.
 * In doing so, a MMC card never enters SPI-mode communications,
 * but now the SecureDigital card-detect feature of CD/DAT3 is ineffective
 * (the low to high transition will not occur).
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mm.h>
#include <linux/interrupt.h>
#include <linux/dma-mapping.h>
#include <linux/scatterlist.h>
#include <linux/leds.h>
#include <linux/mmc/host.h>
#include <linux/slab.h>

#include <asm/io.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1xxx_dbdma.h>
#include <asm/mach-au1x00/au1100_mmc.h>

#define DRIVER_NAME "au1xxx-mmc"

/* Set this to enable special debugging macros */
/* #define DEBUG */

#ifdef DEBUG
#define DBG(fmt, idx, args...)	\
	pr_debug("au1xmmc(%d): DEBUG: " fmt, idx, ##args)
#else
#define DBG(fmt, idx, args...) do {} while (0)
#endif

/* Hardware definitions */
#define AU1XMMC_DESCRIPTOR_COUNT 1

/* max DMA seg size: 64KB on Au1100, 4MB on Au1200 */
#define AU1100_MMC_DESCRIPTOR_SIZE 0x0000ffff
#define AU1200_MMC_DESCRIPTOR_SIZE 0x003fffff

#define AU1XMMC_OCR (MMC_VDD_27_28 | MMC_VDD_28_29 | MMC_VDD_29_30 | \
		     MMC_VDD_30_31 | MMC_VDD_31_32 | MMC_VDD_32_33 | \
		     MMC_VDD_33_34 | MMC_VDD_34_35 | MMC_VDD_35_36)

/* This gives us a hard value for the stop command that we can write directly
 * to the command register.
 */
#define STOP_CMD	\
	(SD_CMD_RT_1B | SD_CMD_CT_7 | (0xC << SD_CMD_CI_SHIFT) | SD_CMD_GO)

/* This is the set of interrupts that we configure by default. */
#define AU1XMMC_INTERRUPTS 				\
	(SD_CONFIG_SC | SD_CONFIG_DT | SD_CONFIG_RAT |	\
	 SD_CONFIG_CR | SD_CONFIG_I)

/* The poll event (looking for insert/remove events runs twice a second. */
#define AU1XMMC_DETECT_TIMEOUT (HZ/2)

struct au1xmmc_host {
	struct mmc_host *mmc;
	struct mmc_request *mrq;

	u32 flags;
	u32 iobase;
	u32 clock;
	u32 bus_width;
	u32 power_mode;

	int status;

	struct {
		int len;
		int dir;
	} dma;

	struct {
		int index;
		int offset;
		int len;
	} pio;

	u32 tx_chan;
	u32 rx_chan;

	int irq;

	struct tasklet_struct finish_task;
	struct tasklet_struct data_task;
	struct au1xmmc_platform_data *platdata;
	struct platform_device *pdev;
	struct resource *ioarea;
};

/* Status flags used by the host structure */
#define HOST_F_XMIT	0x0001
#define HOST_F_RECV	0x0002
#define HOST_F_DMA	0x0010
#define HOST_F_DBDMA	0x0020
#define HOST_F_ACTIVE	0x0100
#define HOST_F_STOP	0x1000

#define HOST_S_IDLE	0x0001
#define HOST_S_CMD	0x0002
#define HOST_S_DATA	0x0003
#define HOST_S_STOP	0x0004

/* Easy access macros */
#define HOST_STATUS(h)	((h)->iobase + SD_STATUS)
#define HOST_CONFIG(h)	((h)->iobase + SD_CONFIG)
#define HOST_ENABLE(h)	((h)->iobase + SD_ENABLE)
#define HOST_TXPORT(h)	((h)->iobase + SD_TXPORT)
#define HOST_RXPORT(h)	((h)->iobase + SD_RXPORT)
#define HOST_CMDARG(h)	((h)->iobase + SD_CMDARG)
#define HOST_BLKSIZE(h)	((h)->iobase + SD_BLKSIZE)
#define HOST_CMD(h)	((h)->iobase + SD_CMD)
#define HOST_CONFIG2(h)	((h)->iobase + SD_CONFIG2)
#define HOST_TIMEOUT(h)	((h)->iobase + SD_TIMEOUT)
#define HOST_DEBUG(h)	((h)->iobase + SD_DEBUG)

#define DMA_CHANNEL(h)	\
	(((h)->flags & HOST_F_XMIT) ? (h)->tx_chan : (h)->rx_chan)

static inline int has_dbdma(void)
{
	switch (alchemy_get_cputype()) {
	case ALCHEMY_CPU_AU1200:
	case ALCHEMY_CPU_AU1300:
		return 1;
	default:
		return 0;
	}
}

static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask)
{
	u32 val = au_readl(HOST_CONFIG(host));
	val |= mask;
	au_writel(val, HOST_CONFIG(host));
	au_sync();
}

static inline void FLUSH_FIFO(struct au1xmmc_host *host)
{
	u32 val = au_readl(HOST_CONFIG2(host));

	au_writel(val | SD_CONFIG2_FF, HOST_CONFIG2(host));
	au_sync_delay(1);

	/* SEND_STOP will turn off clock control - this re-enables it */
	val &= ~SD_CONFIG2_DF;

	au_writel(val, HOST_CONFIG2(host));
	au_sync();
}

static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask)
{
	u32 val = au_readl(HOST_CONFIG(host));
	val &= ~mask;
	au_writel(val, HOST_CONFIG(host));
	au_sync();
}

static inline void SEND_STOP(struct au1xmmc_host *host)
{
	u32 config2;

	WARN_ON(host->status != HOST_S_DATA);
	host->status = HOST_S_STOP;

	config2 = au_readl(HOST_CONFIG2(host));
	au_writel(config2 | SD_CONFIG2_DF, HOST_CONFIG2(host));
	au_sync();

	/* Send the stop command */
	au_writel(STOP_CMD, HOST_CMD(host));
}

static void au1xmmc_set_power(struct au1xmmc_host *host, int state)
{
	if (host->platdata && host->platdata->set_power)
		host->platdata->set_power(host->mmc, state);
}

static int au1xmmc_card_inserted(struct mmc_host *mmc)
{
	struct au1xmmc_host *host = mmc_priv(mmc);

	if (host->platdata && host->platdata->card_inserted)
		return !!host->platdata->card_inserted(host->mmc);

	return -ENOSYS;
}

static int au1xmmc_card_readonly(struct mmc_host *mmc)
{
	struct au1xmmc_host *host = mmc_priv(mmc);

	if (host->platdata && host->platdata->card_readonly)
		return !!host->platdata->card_readonly(mmc);

	return -ENOSYS;
}

static void au1xmmc_finish_request(struct au1xmmc_host *host)
{
	struct mmc_request *mrq = host->mrq;

	host->mrq = NULL;
	host->flags &= HOST_F_ACTIVE | HOST_F_DMA;

	host->dma.len = 0;
	host->dma.dir = 0;

	host->pio.index  = 0;
	host->pio.offset = 0;
	host->pio.len = 0;

	host->status = HOST_S_IDLE;

	mmc_request_done(host->mmc, mrq);
}

static void au1xmmc_tasklet_finish(unsigned long param)
{
	struct au1xmmc_host *host = (struct au1xmmc_host *) param;
	au1xmmc_finish_request(host);
}

static int au1xmmc_send_command(struct au1xmmc_host *host, int wait,
				struct mmc_command *cmd, struct mmc_data *data)
{
	u32 mmccmd = (cmd->opcode << SD_CMD_CI_SHIFT);

	switch (mmc_resp_type(cmd)) {
	case MMC_RSP_NONE:
		break;
	case MMC_RSP_R1:
		mmccmd |= SD_CMD_RT_1;
		break;
	case MMC_RSP_R1B:
		mmccmd |= SD_CMD_RT_1B;
		break;
	case MMC_RSP_R2:
		mmccmd |= SD_CMD_RT_2;
		break;
	case MMC_RSP_R3:
		mmccmd |= SD_CMD_RT_3;
		break;
	default:
		pr_info("au1xmmc: unhandled response type %02x\n",
			mmc_resp_type(cmd));
		return -EINVAL;
	}

	if (data) {
		if (data->flags & MMC_DATA_READ) {
			if (data->blocks > 1)
				mmccmd |= SD_CMD_CT_4;
			else
				mmccmd |= SD_CMD_CT_2;
		} else if (data->flags & MMC_DATA_WRITE) {
			if (data->blocks > 1)
				mmccmd |= SD_CMD_CT_3;
			else
				mmccmd |= SD_CMD_CT_1;
		}
	}

	au_writel(cmd->arg, HOST_CMDARG(host));
	au_sync();

	if (wait)
		IRQ_OFF(host, SD_CONFIG_CR);

	au_writel((mmccmd | SD_CMD_GO), HOST_CMD(host));
	au_sync();

	/* Wait for the command to go on the line */
	while (au_readl(HOST_CMD(host)) & SD_CMD_GO)
		/* nop */;

	/* Wait for the command to come back */
	if (wait) {
		u32 status = au_readl(HOST_STATUS(host));

		while (!(status & SD_STATUS_CR))
			status = au_readl(HOST_STATUS(host));

		/* Clear the CR status */
		au_writel(SD_STATUS_CR, HOST_STATUS(host));

		IRQ_ON(host, SD_CONFIG_CR);
	}

	return 0;
}

static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status)
{
	struct mmc_request *mrq = host->mrq;
	struct mmc_data *data;
	u32 crc;

	WARN_ON((host->status != HOST_S_DATA) && (host->status != HOST_S_STOP));

	if (host->mrq == NULL)
		return;

	data = mrq->cmd->data;

	if (status == 0)
		status = au_readl(HOST_STATUS(host));

	/* The transaction is really over when the SD_STATUS_DB bit is clear */
	while ((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB))
		status = au_readl(HOST_STATUS(host));

	data->error = 0;
	dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir);

        /* Process any errors */
	crc = (status & (SD_STATUS_WC | SD_STATUS_RC));
	if (host->flags & HOST_F_XMIT)
		crc |= ((status & 0x07) == 0x02) ? 0 : 1;

	if (crc)
		data->error = -EILSEQ;

	/* Clear the CRC bits */
	au_writel(SD_STATUS_WC | SD_STATUS_RC, HOST_STATUS(host));

	data->bytes_xfered = 0;

	if (!data->error) {
		if (host->flags & (HOST_F_DMA | HOST_F_DBDMA)) {
			u32 chan = DMA_CHANNEL(host);

			chan_tab_t *c = *((chan_tab_t **)chan);
			au1x_dma_chan_t *cp = c->chan_ptr;
			data->bytes_xfered = cp->ddma_bytecnt;
		} else
			data->bytes_xfered =
				(data->blocks * data->blksz) - host->pio.len;
	}

	au1xmmc_finish_request(host);
}

static void au1xmmc_tasklet_data(unsigned long param)
{
	struct au1xmmc_host *host = (struct au1xmmc_host *)param;

	u32 status = au_readl(HOST_STATUS(host));
	au1xmmc_data_complete(host, status);
}

#define AU1XMMC_MAX_TRANSFER 8

static void au1xmmc_send_pio(struct au1xmmc_host *host)
{
	struct mmc_data *data;
	int sg_len, max, count;
	unsigned char *sg_ptr, val;
	u32 status;
	struct scatterlist *sg;

	data = host->mrq->data;

	if (!(host->flags & HOST_F_XMIT))
		return;

	/* This is the pointer to the data buffer */
	sg = &data->sg[host->pio.index];
	sg_ptr = sg_virt(sg) + host->pio.offset;

	/* This is the space left inside the buffer */
	sg_len = data->sg[host->pio.index].length - host->pio.offset;

	/* Check if we need less than the size of the sg_buffer */
	max = (sg_len > host->pio.len) ? host->pio.len : sg_len;
	if (max > AU1XMMC_MAX_TRANSFER)
		max = AU1XMMC_MAX_TRANSFER;

	for (count = 0; count < max; count++) {
		status = au_readl(HOST_STATUS(host));

		if (!(status & SD_STATUS_TH))
			break;

		val = *sg_ptr++;

		au_writel((unsigned long)val, HOST_TXPORT(host));
		au_sync();
	}

	host->pio.len -= count;
	host->pio.offset += count;

	if (count == sg_len) {
		host->pio.index++;
		host->pio.offset = 0;
	}

	if (host->pio.len == 0) {
		IRQ_OFF(host, SD_CONFIG_TH);

		if (host->flags & HOST_F_STOP)
			SEND_STOP(host);

		tasklet_schedule(&host->data_task);
	}
}

static void au1xmmc_receive_pio(struct au1xmmc_host *host)
{
	struct mmc_data *data;
	int max, count, sg_len = 0;
	unsigned char *sg_ptr = NULL;
	u32 status, val;
	struct scatterlist *sg;

	data = host->mrq->data;

	if (!(host->flags & HOST_F_RECV))
		return;

	max = host->pio.len;

	if (host->pio.index < host->dma.len) {
		sg = &data->sg[host->pio.index];
		sg_ptr = sg_virt(sg) + host->pio.offset;

		/* This is the space left inside the buffer */
		sg_len = sg_dma_len(&data->sg[host->pio.index]) - host->pio.offset;

		/* Check if we need less than the size of the sg_buffer */
		if (sg_len < max)
			max = sg_len;
	}

	if (max > AU1XMMC_MAX_TRANSFER)
		max = AU1XMMC_MAX_TRANSFER;

	for (count = 0; count < max; count++) {
		status = au_readl(HOST_STATUS(host));

		if (!(status & SD_STATUS_NE))
			break;

		if (status & SD_STATUS_RC) {
			DBG("RX CRC Error [%d + %d].\n", host->pdev->id,
					host->pio.len, count);
			break;
		}

		if (status & SD_STATUS_RO) {
			DBG("RX Overrun [%d + %d]\n", host->pdev->id,
					host->pio.len, count);
			break;
		}
		else if (status & SD_STATUS_RU) {
			DBG("RX Underrun [%d + %d]\n", host->pdev->id,
					host->pio.len,	count);
			break;
		}

		val = au_readl(HOST_RXPORT(host));

		if (sg_ptr)
			*sg_ptr++ = (unsigned char)(val & 0xFF);
	}

	host->pio.len -= count;
	host->pio.offset += count;

	if (sg_len && count == sg_len) {
		host->pio.index++;
		host->pio.offset = 0;
	}

	if (host->pio.len == 0) {
		/* IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF); */
		IRQ_OFF(host, SD_CONFIG_NE);

		if (host->flags & HOST_F_STOP)
			SEND_STOP(host);

		tasklet_schedule(&host->data_task);
	}
}

/* This is called when a command has been completed - grab the response
 * and check for errors.  Then start the data transfer if it is indicated.
 */
static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status)
{
	struct mmc_request *mrq = host->mrq;
	struct mmc_command *cmd;
	u32 r[4];
	int i, trans;

	if (!host->mrq)
		return;

	cmd = mrq->cmd;
	cmd->error = 0;

	if (cmd->flags & MMC_RSP_PRESENT) {
		if (cmd->flags & MMC_RSP_136) {
			r[0] = au_readl(host->iobase + SD_RESP3);
			r[1] = au_readl(host->iobase + SD_RESP2);
			r[2] = au_readl(host->iobase + SD_RESP1);
			r[3] = au_readl(host->iobase + SD_RESP0);

			/* The CRC is omitted from the response, so really
			 * we only got 120 bytes, but the engine expects
			 * 128 bits, so we have to shift things up.
			 */
			for (i = 0; i < 4; i++) {
				cmd->resp[i] = (r[i] & 0x00FFFFFF) << 8;
				if (i != 3)
					cmd->resp[i] |= (r[i + 1] & 0xFF000000) >> 24;
			}
		} else {
			/* Techincally, we should be getting all 48 bits of
			 * the response (SD_RESP1 + SD_RESP2), but because
			 * our response omits the CRC, our data ends up
			 * being shifted 8 bits to the right.  In this case,
			 * that means that the OSR data starts at bit 31,
			 * so we can just read RESP0 and return that.
			 */
			cmd->resp[0] = au_readl(host->iobase + SD_RESP0);
		}
	}

        /* Figure out errors */
	if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC))
		cmd->error = -EILSEQ;

	trans = host->flags & (HOST_F_XMIT | HOST_F_RECV);

	if (!trans || cmd->error) {
		IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA | SD_CONFIG_RF);
		tasklet_schedule(&host->finish_task);
		return;
	}

	host->status = HOST_S_DATA;

	if ((host->flags & (HOST_F_DMA | HOST_F_DBDMA))) {
		u32 channel = DMA_CHANNEL(host);

		/* Start the DBDMA as soon as the buffer gets something in it */

		if (host->flags & HOST_F_RECV) {
			u32 mask = SD_STATUS_DB | SD_STATUS_NE;

			while((status & mask) != mask)
				status = au_readl(HOST_STATUS(host));
		}

		au1xxx_dbdma_start(channel);
	}
}

static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate)
{
	unsigned int pbus = get_au1x00_speed();
	unsigned int divisor;
	u32 config;

	/* From databook:
	 * divisor = ((((cpuclock / sbus_divisor) / 2) / mmcclock) / 2) - 1
	 */
	pbus /= ((au_readl(SYS_POWERCTRL) & 0x3) + 2);
	pbus /= 2;
	divisor = ((pbus / rate) / 2) - 1;

	config = au_readl(HOST_CONFIG(host));

	config &= ~(SD_CONFIG_DIV);
	config |= (divisor & SD_CONFIG_DIV) | SD_CONFIG_DE;

	au_writel(config, HOST_CONFIG(host));
	au_sync();
}

static int au1xmmc_prepare_data(struct au1xmmc_host *host,
				struct mmc_data *data)
{
	int datalen = data->blocks * data->blksz;

	if (data->flags & MMC_DATA_READ)
		host->flags |= HOST_F_RECV;
	else
		host->flags |= HOST_F_XMIT;

	if (host->mrq->stop)
		host->flags |= HOST_F_STOP;

	host->dma.dir = DMA_BIDIRECTIONAL;

	host->dma.len = dma_map_sg(mmc_dev(host->mmc), data->sg,
				   data->sg_len, host->dma.dir);

	if (host->dma.len == 0)
		return -ETIMEDOUT;

	au_writel(data->blksz - 1, HOST_BLKSIZE(host));

	if (host->flags & (HOST_F_DMA | HOST_F_DBDMA)) {
		int i;
		u32 channel = DMA_CHANNEL(host);

		au1xxx_dbdma_stop(channel);

		for (i = 0; i < host->dma.len; i++) {
			u32 ret = 0, flags = DDMA_FLAGS_NOIE;
			struct scatterlist *sg = &data->sg[i];
			int sg_len = sg->length;

			int len = (datalen > sg_len) ? sg_len : datalen;

			if (i == host->dma.len - 1)
				flags = DDMA_FLAGS_IE;

			if (host->flags & HOST_F_XMIT) {
				ret = au1xxx_dbdma_put_source(channel,
					sg_phys(sg), len, flags);
			} else {
				ret = au1xxx_dbdma_put_dest(channel,
					sg_phys(sg), len, flags);
			}

			if (!ret)
				goto dataerr;

			datalen -= len;
		}
	} else {
		host->pio.index = 0;
		host->pio.offset = 0;
		host->pio.len = datalen;

		if (host->flags & HOST_F_XMIT)
			IRQ_ON(host, SD_CONFIG_TH);
		else
			IRQ_ON(host, SD_CONFIG_NE);
			/* IRQ_ON(host, SD_CONFIG_RA | SD_CONFIG_RF); */
	}

	return 0;

dataerr:
	dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
			host->dma.dir);
	return -ETIMEDOUT;
}

/* This actually starts a command or data transaction */
static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq)
{
	struct au1xmmc_host *host = mmc_priv(mmc);
	int ret = 0;

	WARN_ON(irqs_disabled());
	WARN_ON(host->status != HOST_S_IDLE);

	host->mrq = mrq;
	host->status = HOST_S_CMD;

	/* fail request immediately if no card is present */
	if (0 == au1xmmc_card_inserted(mmc)) {
		mrq->cmd->error = -ENOMEDIUM;
		au1xmmc_finish_request(host);
		return;
	}

	if (mrq->data) {
		FLUSH_FIFO(host);
		ret = au1xmmc_prepare_data(host, mrq->data);
	}

	if (!ret)
		ret = au1xmmc_send_command(host, 0, mrq->cmd, mrq->data);

	if (ret) {
		mrq->cmd->error = ret;
		au1xmmc_finish_request(host);
	}
}

static void au1xmmc_reset_controller(struct au1xmmc_host *host)
{
	/* Apply the clock */
	au_writel(SD_ENABLE_CE, HOST_ENABLE(host));
        au_sync_delay(1);

	au_writel(SD_ENABLE_R | SD_ENABLE_CE, HOST_ENABLE(host));
	au_sync_delay(5);

	au_writel(~0, HOST_STATUS(host));
	au_sync();

	au_writel(0, HOST_BLKSIZE(host));
	au_writel(0x001fffff, HOST_TIMEOUT(host));
	au_sync();

	au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
        au_sync();

	au_writel(SD_CONFIG2_EN | SD_CONFIG2_FF, HOST_CONFIG2(host));
	au_sync_delay(1);

	au_writel(SD_CONFIG2_EN, HOST_CONFIG2(host));
	au_sync();

	/* Configure interrupts */
	au_writel(AU1XMMC_INTERRUPTS, HOST_CONFIG(host));
	au_sync();
}


static void au1xmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
{
	struct au1xmmc_host *host = mmc_priv(mmc);
	u32 config2;

	if (ios->power_mode == MMC_POWER_OFF)
		au1xmmc_set_power(host, 0);
	else if (ios->power_mode == MMC_POWER_ON) {
		au1xmmc_set_power(host, 1);
	}

	if (ios->clock && ios->clock != host->clock) {
		au1xmmc_set_clock(host, ios->clock);
		host->clock = ios->clock;
	}

	config2 = au_readl(HOST_CONFIG2(host));
	switch (ios->bus_width) {
	case MMC_BUS_WIDTH_8:
		config2 |= SD_CONFIG2_BB;
		break;
	case MMC_BUS_WIDTH_4:
		config2 &= ~SD_CONFIG2_BB;
		config2 |= SD_CONFIG2_WB;
		break;
	case MMC_BUS_WIDTH_1:
		config2 &= ~(SD_CONFIG2_WB | SD_CONFIG2_BB);
		break;
	}
	au_writel(config2, HOST_CONFIG2(host));
	au_sync();
}

#define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT)
#define STATUS_DATA_IN  (SD_STATUS_NE)
#define STATUS_DATA_OUT (SD_STATUS_TH)

static irqreturn_t au1xmmc_irq(int irq, void *dev_id)
{
	struct au1xmmc_host *host = dev_id;
	u32 status;

	status = au_readl(HOST_STATUS(host));

	if (!(status & SD_STATUS_I))
		return IRQ_NONE;	/* not ours */

	if (status & SD_STATUS_SI)	/* SDIO */
		mmc_signal_sdio_irq(host->mmc);

	if (host->mrq && (status & STATUS_TIMEOUT)) {
		if (status & SD_STATUS_RAT)
			host->mrq->cmd->error = -ETIMEDOUT;
		else if (status & SD_STATUS_DT)
			host->mrq->data->error = -ETIMEDOUT;

		/* In PIO mode, interrupts might still be enabled */
		IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH);

		/* IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA | SD_CONFIG_RF); */
		tasklet_schedule(&host->finish_task);
	}
#if 0
	else if (status & SD_STATUS_DD) {
		/* Sometimes we get a DD before a NE in PIO mode */
		if (!(host->flags & HOST_F_DMA) && (status & SD_STATUS_NE))
			au1xmmc_receive_pio(host);
		else {
			au1xmmc_data_complete(host, status);
			/* tasklet_schedule(&host->data_task); */
		}
	}
#endif
	else if (status & SD_STATUS_CR) {
		if (host->status == HOST_S_CMD)
			au1xmmc_cmd_complete(host, status);

	} else if (!(host->flags & HOST_F_DMA)) {
		if ((host->flags & HOST_F_XMIT) && (status & STATUS_DATA_OUT))
			au1xmmc_send_pio(host);
		else if ((host->flags & HOST_F_RECV) && (status & STATUS_DATA_IN))
			au1xmmc_receive_pio(host);

	} else if (status & 0x203F3C70) {
			DBG("Unhandled status %8.8x\n", host->pdev->id,
				status);
	}

	au_writel(status, HOST_STATUS(host));
	au_sync();

	return IRQ_HANDLED;
}

/* 8bit memory DMA device */
static dbdev_tab_t au1xmmc_mem_dbdev = {
	.dev_id		= DSCR_CMD0_ALWAYS,
	.dev_flags	= DEV_FLAGS_ANYUSE,
	.dev_tsize	= 0,
	.dev_devwidth	= 8,
	.dev_physaddr	= 0x00000000,
	.dev_intlevel	= 0,
	.dev_intpolarity = 0,
};
static int memid;

static void au1xmmc_dbdma_callback(int irq, void *dev_id)
{
	struct au1xmmc_host *host = (struct au1xmmc_host *)dev_id;

	/* Avoid spurious interrupts */
	if (!host->mrq)
		return;

	if (host->flags & HOST_F_STOP)
		SEND_STOP(host);

	tasklet_schedule(&host->data_task);
}

static int au1xmmc_dbdma_init(struct au1xmmc_host *host)
{
	struct resource *res;
	int txid, rxid;

	res = platform_get_resource(host->pdev, IORESOURCE_DMA, 0);
	if (!res)
		return -ENODEV;
	txid = res->start;

	res = platform_get_resource(host->pdev, IORESOURCE_DMA, 1);
	if (!res)
		return -ENODEV;
	rxid = res->start;

	if (!memid)
		return -ENODEV;

	host->tx_chan = au1xxx_dbdma_chan_alloc(memid, txid,
				au1xmmc_dbdma_callback, (void *)host);
	if (!host->tx_chan) {
		dev_err(&host->pdev->dev, "cannot allocate TX DMA\n");
		return -ENODEV;
	}

	host->rx_chan = au1xxx_dbdma_chan_alloc(rxid, memid,
				au1xmmc_dbdma_callback, (void *)host);
	if (!host->rx_chan) {
		dev_err(&host->pdev->dev, "cannot allocate RX DMA\n");
		au1xxx_dbdma_chan_free(host->tx_chan);
		return -ENODEV;
	}

	au1xxx_dbdma_set_devwidth(host->tx_chan, 8);
	au1xxx_dbdma_set_devwidth(host->rx_chan, 8);

	au1xxx_dbdma_ring_alloc(host->tx_chan, AU1XMMC_DESCRIPTOR_COUNT);
	au1xxx_dbdma_ring_alloc(host->rx_chan, AU1XMMC_DESCRIPTOR_COUNT);

	/* DBDMA is good to go */
	host->flags |= HOST_F_DMA | HOST_F_DBDMA;

	return 0;
}

static void au1xmmc_dbdma_shutdown(struct au1xmmc_host *host)
{
	if (host->flags & HOST_F_DMA) {
		host->flags &= ~HOST_F_DMA;
		au1xxx_dbdma_chan_free(host->tx_chan);
		au1xxx_dbdma_chan_free(host->rx_chan);
	}
}

static void au1xmmc_enable_sdio_irq(struct mmc_host *mmc, int en)
{
	struct au1xmmc_host *host = mmc_priv(mmc);

	if (en)
		IRQ_ON(host, SD_CONFIG_SI);
	else
		IRQ_OFF(host, SD_CONFIG_SI);
}

static const struct mmc_host_ops au1xmmc_ops = {
	.request	= au1xmmc_request,
	.set_ios	= au1xmmc_set_ios,
	.get_ro		= au1xmmc_card_readonly,
	.get_cd		= au1xmmc_card_inserted,
	.enable_sdio_irq = au1xmmc_enable_sdio_irq,
};

static int au1xmmc_probe(struct platform_device *pdev)
{
	struct mmc_host *mmc;
	struct au1xmmc_host *host;
	struct resource *r;
	int ret, iflag;

	mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev);
	if (!mmc) {
		dev_err(&pdev->dev, "no memory for mmc_host\n");
		ret = -ENOMEM;
		goto out0;
	}

	host = mmc_priv(mmc);
	host->mmc = mmc;
	host->platdata = pdev->dev.platform_data;
	host->pdev = pdev;

	ret = -ENODEV;
	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	if (!r) {
		dev_err(&pdev->dev, "no mmio defined\n");
		goto out1;
	}

	host->ioarea = request_mem_region(r->start, resource_size(r),
					   pdev->name);
	if (!host->ioarea) {
		dev_err(&pdev->dev, "mmio already in use\n");
		goto out1;
	}

	host->iobase = (unsigned long)ioremap(r->start, 0x3c);
	if (!host->iobase) {
		dev_err(&pdev->dev, "cannot remap mmio\n");
		goto out2;
	}

	r = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
	if (!r) {
		dev_err(&pdev->dev, "no IRQ defined\n");
		goto out3;
	}
	host->irq = r->start;

	mmc->ops = &au1xmmc_ops;

	mmc->f_min =   450000;
	mmc->f_max = 24000000;

	mmc->max_blk_size = 2048;
	mmc->max_blk_count = 512;

	mmc->ocr_avail = AU1XMMC_OCR;
	mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
	mmc->max_segs = AU1XMMC_DESCRIPTOR_COUNT;

	iflag = IRQF_SHARED;	/* Au1100/Au1200: one int for both ctrls */

	switch (alchemy_get_cputype()) {
	case ALCHEMY_CPU_AU1100:
		mmc->max_seg_size = AU1100_MMC_DESCRIPTOR_SIZE;
		break;
	case ALCHEMY_CPU_AU1200:
		mmc->max_seg_size = AU1200_MMC_DESCRIPTOR_SIZE;
		break;
	case ALCHEMY_CPU_AU1300:
		iflag = 0;	/* nothing is shared */
		mmc->max_seg_size = AU1200_MMC_DESCRIPTOR_SIZE;
		mmc->f_max = 52000000;
		if (host->ioarea->start == AU1100_SD0_PHYS_ADDR)
			mmc->caps |= MMC_CAP_8_BIT_DATA;
		break;
	}

	ret = request_irq(host->irq, au1xmmc_irq, iflag, DRIVER_NAME, host);
	if (ret) {
		dev_err(&pdev->dev, "cannot grab IRQ\n");
		goto out3;
	}

	host->status = HOST_S_IDLE;

	/* board-specific carddetect setup, if any */
	if (host->platdata && host->platdata->cd_setup) {
		ret = host->platdata->cd_setup(mmc, 1);
		if (ret) {
			dev_warn(&pdev->dev, "board CD setup failed\n");
			mmc->caps |= MMC_CAP_NEEDS_POLL;
		}
	} else
		mmc->caps |= MMC_CAP_NEEDS_POLL;

	/* platform may not be able to use all advertised caps */
	if (host->platdata)
		mmc->caps &= ~(host->platdata->mask_host_caps);

	tasklet_init(&host->data_task, au1xmmc_tasklet_data,
			(unsigned long)host);

	tasklet_init(&host->finish_task, au1xmmc_tasklet_finish,
			(unsigned long)host);

	if (has_dbdma()) {
		ret = au1xmmc_dbdma_init(host);
		if (ret)
			pr_info(DRIVER_NAME ": DBDMA init failed; using PIO\n");
	}

#ifdef CONFIG_LEDS_CLASS
	if (host->platdata && host->platdata->led) {
		struct led_classdev *led = host->platdata->led;
		led->name = mmc_hostname(mmc);
		led->brightness = LED_OFF;
		led->default_trigger = mmc_hostname(mmc);
		ret = led_classdev_register(mmc_dev(mmc), led);
		if (ret)
			goto out5;
	}
#endif

	au1xmmc_reset_controller(host);

	ret = mmc_add_host(mmc);
	if (ret) {
		dev_err(&pdev->dev, "cannot add mmc host\n");
		goto out6;
	}

	platform_set_drvdata(pdev, host);

	pr_info(DRIVER_NAME ": MMC Controller %d set up at %8.8X"
		" (mode=%s)\n", pdev->id, host->iobase,
		host->flags & HOST_F_DMA ? "dma" : "pio");

	return 0;	/* all ok */

out6:
#ifdef CONFIG_LEDS_CLASS
	if (host->platdata && host->platdata->led)
		led_classdev_unregister(host->platdata->led);
out5:
#endif
	au_writel(0, HOST_ENABLE(host));
	au_writel(0, HOST_CONFIG(host));
	au_writel(0, HOST_CONFIG2(host));
	au_sync();

	if (host->flags & HOST_F_DBDMA)
		au1xmmc_dbdma_shutdown(host);

	tasklet_kill(&host->data_task);
	tasklet_kill(&host->finish_task);

	if (host->platdata && host->platdata->cd_setup &&
	    !(mmc->caps & MMC_CAP_NEEDS_POLL))
		host->platdata->cd_setup(mmc, 0);

	free_irq(host->irq, host);
out3:
	iounmap((void *)host->iobase);
out2:
	release_resource(host->ioarea);
	kfree(host->ioarea);
out1:
	mmc_free_host(mmc);
out0:
	return ret;
}

static int au1xmmc_remove(struct platform_device *pdev)
{
	struct au1xmmc_host *host = platform_get_drvdata(pdev);

	if (host) {
		mmc_remove_host(host->mmc);

#ifdef CONFIG_LEDS_CLASS
		if (host->platdata && host->platdata->led)
			led_classdev_unregister(host->platdata->led);
#endif

		if (host->platdata && host->platdata->cd_setup &&
		    !(host->mmc->caps & MMC_CAP_NEEDS_POLL))
			host->platdata->cd_setup(host->mmc, 0);

		au_writel(0, HOST_ENABLE(host));
		au_writel(0, HOST_CONFIG(host));
		au_writel(0, HOST_CONFIG2(host));
		au_sync();

		tasklet_kill(&host->data_task);
		tasklet_kill(&host->finish_task);

		if (host->flags & HOST_F_DBDMA)
			au1xmmc_dbdma_shutdown(host);

		au1xmmc_set_power(host, 0);

		free_irq(host->irq, host);
		iounmap((void *)host->iobase);
		release_resource(host->ioarea);
		kfree(host->ioarea);

		mmc_free_host(host->mmc);
	}
	return 0;
}

#ifdef CONFIG_PM
static int au1xmmc_suspend(struct platform_device *pdev, pm_message_t state)
{
	struct au1xmmc_host *host = platform_get_drvdata(pdev);
	int ret;

	ret = mmc_suspend_host(host->mmc);
	if (ret)
		return ret;

	au_writel(0, HOST_CONFIG2(host));
	au_writel(0, HOST_CONFIG(host));
	au_writel(0xffffffff, HOST_STATUS(host));
	au_writel(0, HOST_ENABLE(host));
	au_sync();

	return 0;
}

static int au1xmmc_resume(struct platform_device *pdev)
{
	struct au1xmmc_host *host = platform_get_drvdata(pdev);

	au1xmmc_reset_controller(host);

	return mmc_resume_host(host->mmc);
}
#else
#define au1xmmc_suspend NULL
#define au1xmmc_resume NULL
#endif

static struct platform_driver au1xmmc_driver = {
	.probe         = au1xmmc_probe,
	.remove        = au1xmmc_remove,
	.suspend       = au1xmmc_suspend,
	.resume        = au1xmmc_resume,
	.driver        = {
		.name  = DRIVER_NAME,
		.owner = THIS_MODULE,
	},
};

static int __init au1xmmc_init(void)
{
	if (has_dbdma()) {
		/* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride
		* of 8 bits.  And since devices are shared, we need to create
		* our own to avoid freaking out other devices.
		*/
		memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev);
		if (!memid)
			pr_err("au1xmmc: cannot add memory dbdma\n");
	}
	return platform_driver_register(&au1xmmc_driver);
}

static void __exit au1xmmc_exit(void)
{
	if (has_dbdma() && memid)
		au1xxx_ddma_del_device(memid);

	platform_driver_unregister(&au1xmmc_driver);
}

module_init(au1xmmc_init);
module_exit(au1xmmc_exit);

MODULE_AUTHOR("Advanced Micro Devices, Inc");
MODULE_DESCRIPTION("MMC/SD driver for the Alchemy Au1XXX");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:au1xxx-mmc");