p71924506
/
linux_old1
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
linux_old1/drivers/pci/Kconfig

79 lines
2.0 KiB
Plaintext
Raw Normal View History

Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
#
# PCI configuration
#
msi: introduce ARCH_SUPPORTS_MSI Kconfig option (rev2) Allows architectures to advertise that they support MSI rather than listing each architecture as a PCI_MSI dependency. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-18 16:46:20 +08:00
config ARCH_SUPPORTS_MSI
bool
default n
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
config PCI_MSI
bool "Message Signaled Interrupts (MSI and MSI-X)"
depends on PCI
msi: introduce ARCH_SUPPORTS_MSI Kconfig option (rev2) Allows architectures to advertise that they support MSI rather than listing each architecture as a PCI_MSI dependency. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-18 16:46:20 +08:00
depends on ARCH_SUPPORTS_MSI
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
help
This allows device drivers to enable MSI (Message Signaled
Interrupts). Message Signaled Interrupts enable a device to
generate an interrupt using an inbound Memory Write on its
PCI bus instead of asserting a device IRQ pin.
[PATCH] PCI: Provide a boot parameter to disable MSI Several drivers are starting to grow options to disable MSI. However, it's often a host chipset issue, not something which individual drivers should handle. So we add the pci=nomsi kernel parameter to allow the user to disable MSI modes for systems we haven't added to the quirk list yet. Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-03-06 13:33:34 +08:00
Use of PCI MSI interrupts can be disabled at kernel boot time
by using the 'pci=nomsi' option. This disables MSI for the
entire system.
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
If you don't know what to do here, say N.
PCI: Add Kconfig option to disable deprecated pci_find_* API Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-29 21:48:09 +08:00
config PCI_LEGACY
bool "Enable deprecated pci_find_* API"
depends on PCI
default y
help
Say Y here if you want to include support for the deprecated
PCI: remove pci_find_slot from PCI_LEGACY config description Commit 3b073eda has removed pci_find_slot, so there's no point in mentioning it in the config description as one of the deprecated APIs there are enabled by PCI_LEGACY and still used by some drivers. Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-10-31 03:46:48 +08:00
pci_find_device() API. Most drivers have been converted over
to using the proper hotplug APIs, so this option serves to
include/exclude only a few drivers that are still using this
API.
PCI: Add Kconfig option to disable deprecated pci_find_* API Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-29 21:48:09 +08:00
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
2005-04-17 06:20:36 +08:00
config PCI_DEBUG
bool "PCI Debugging"
depends on PCI && DEBUG_KERNEL
help
Say Y here if you want the PCI core to produce a bunch of debug
messages to the system log. Select this if you are having a
problem with PCI support and want to see more of what is going on.
When in doubt, say N.
PCI: pci-stub module to reserve pci device When doing device assignment with KVM there's currently nothing to protect the device from having a driver in the host as well as the guest. This trivial module just binds the pci device on the host to a stub driver so that a real host driver can't bind to the device. It has no pci id table, it supports only dynamic ids. # echo "8086 10f5" > /sys/bus/pci/drivers/pci-stub/new_id # echo -n 0000:00:19.0 > /sys/bus/pci/drivers/e1000e/unbind # echo -n 0000:00:19.0 > /sys/bus/pci/drivers/pci-stub/bind # ls -l /sys/bus/pci/devices/0000:00:19.0/driver lrwxrwxrwx 1 root root 0 2008-11-25 19:10 /sys/bus/pci/devices/0000:00:19.0/driver -> ../../../bus/pci/drivers/pci-stub Cc: "Kay, Allen M" <allen.m.kay@intel.com> Cc: "Nakajima, Jun" <jun.nakajima@intel.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-11-26 13:17:13 +08:00
config PCI_STUB
tristate "PCI Stub driver"
depends on PCI
help
Say Y or M here if you want be able to reserve a PCI device
when it is going to be assigned to a guest operating system.
When in doubt, say N.
[PATCH] Initial generic hypertransport interrupt support This patch implements two functions ht_create_irq and ht_destroy_irq for use by drivers. Several other functions are implemented as helpers for arch specific irq_chip handlers. The driver for the card I tested this on isn't yet ready to be merged. However this code is and hypertransport irqs are in use in a few other places in the kernel. Not that any of this will get merged before 2.6.19 Because the ipath-ht400 is slightly out of spec this code will need to be generalized to work there. I think all of the powerpc uses are for a plain interrupt controller in a chipset so support for native hypertransport devices is a little less interesting. However I think this is a half way decent model on how to separate arch specific and generic helper code, and I think this is a functional model of how to get the architecture dependencies out of the msi code. [akpm@osdl.org: Kconfig fix] Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Greg KH <greg@kroah.com> Cc: Andi Kleen <ak@muc.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 17:16:55 +08:00
config HT_IRQ
bool "Interrupts on hypertransport devices"
default y
[PATCH] HT_IRQ must depend on PCI CONFIG_PCI=n, CONFIG_HT_IRQ=y results in the following compile error: ... LD vmlinux arch/i386/mach-generic/built-in.o: In function `apicid_to_node': summit.c:(.text+0x53): undefined reference to `apicid_2_node' arch/i386/kernel/built-in.o: In function `arch_setup_ht_irq': (.text+0xcf79): undefined reference to `write_ht_irq_low' arch/i386/kernel/built-in.o: In function `arch_setup_ht_irq': (.text+0xcf85): undefined reference to `write_ht_irq_high' arch/i386/kernel/built-in.o: In function `k7nops': alternative.c:(.data+0x1358): undefined reference to `mask_ht_irq' alternative.c:(.data+0x1360): undefined reference to `unmask_ht_irq' make[1]: *** [vmlinux] Error 1 Bug report by Jesper Juhl. Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-11 16:22:04 +08:00
depends on PCI && X86_LOCAL_APIC && X86_IO_APIC
[PATCH] Initial generic hypertransport interrupt support This patch implements two functions ht_create_irq and ht_destroy_irq for use by drivers. Several other functions are implemented as helpers for arch specific irq_chip handlers. The driver for the card I tested this on isn't yet ready to be merged. However this code is and hypertransport irqs are in use in a few other places in the kernel. Not that any of this will get merged before 2.6.19 Because the ipath-ht400 is slightly out of spec this code will need to be generalized to work there. I think all of the powerpc uses are for a plain interrupt controller in a chipset so support for native hypertransport devices is a little less interesting. However I think this is a half way decent model on how to separate arch specific and generic helper code, and I think this is a functional model of how to get the architecture dependencies out of the msi code. [akpm@osdl.org: Kconfig fix] Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Greg KH <greg@kroah.com> Cc: Andi Kleen <ak@muc.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 17:16:55 +08:00
help
This allows native hypertransport devices to use interrupts.
If unsure say Y.
PCI: initialize and release SR-IOV capability If a device has the SR-IOV capability, initialize it (set the ARI Capable Hierarchy in the lowest numbered PF if necessary; calculate the System Page Size for the VF MMIO, probe the VF Offset, Stride and BARs). A lock for the VF bus allocation is also initialized if a PF is the lowest numbered PF. Reviewed-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Yu Zhao <yu.zhao@intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-03-20 11:25:11 +08:00
config PCI_IOV
bool "PCI IOV support"
depends on PCI
help
I/O Virtualization is a PCI feature supported by some devices
which allows them to create virtual devices which share their
physical resources.
If unsure, say N.
PCI hotplug: move IOAPIC support from acpiphp to ioapic driver This patch moves PCI I/O APIC support from acpiphp to a separate driver. Like pciehp and shpchp, acpiphp handles PCI hotplug, i.e., addition and removal of PCI adapters. But in addition, acpiphp handles some ACPI hotplug, such as the addition of new host bridges, and the I/O APIC support was tangled up with that. I don't think the I/O APIC support needs to be in acpiphp; PCI I/O APICs usually appear as a function on a PCI host bridge, and we'll enumerate the APIC before any of the devices behind the bridge that use it. As far as I know, nobody actually uses I/O APIC hotplug. It depends on acpi_register_ioapic(), which is only implemented for ia64, and I don't think any vendors have supported I/O chassis hotplug yet. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> CC: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com> CC: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2009-10-27 01:20:47 +08:00
config PCI_IOAPIC
bool
depends on PCI
depends on ACPI
depends on HOTPLUG
default y