linux_old1/net/ipv4/gre_offload.c

286 lines
7.0 KiB
C
Raw Normal View History

/*
* IPV4 GSO/GRO offload support
* Linux INET implementation
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*
* GRE GSO support
*/
#include <linux/skbuff.h>
#include <linux/init.h>
#include <net/protocol.h>
#include <net/gre.h>
static struct sk_buff *gre_gso_segment(struct sk_buff *skb,
netdev_features_t features)
{
int tnl_hlen = skb_inner_mac_header(skb) - skb_transport_header(skb);
struct sk_buff *segs = ERR_PTR(-EINVAL);
u16 mac_offset = skb->mac_header;
__be16 protocol = skb->protocol;
u16 mac_len = skb->mac_len;
int gre_offset, outer_hlen;
bool need_csum, gso_partial;
if (!skb->encapsulation)
goto out;
if (unlikely(tnl_hlen < sizeof(struct gre_base_hdr)))
goto out;
if (unlikely(!pskb_may_pull(skb, tnl_hlen)))
goto out;
/* setup inner skb. */
skb->encapsulation = 0;
SKB_GSO_CB(skb)->encap_level = 0;
__skb_pull(skb, tnl_hlen);
skb_reset_mac_header(skb);
skb_set_network_header(skb, skb_inner_network_offset(skb));
skb->mac_len = skb_inner_network_offset(skb);
skb->protocol = skb->inner_protocol;
need_csum = !!(skb_shinfo(skb)->gso_type & SKB_GSO_GRE_CSUM);
skb->encap_hdr_csum = need_csum;
features &= skb->dev->hw_enc_features;
/* segment inner packet. */
segs = skb_mac_gso_segment(skb, features);
if (IS_ERR_OR_NULL(segs)) {
skb_gso_error_unwind(skb, protocol, tnl_hlen, mac_offset,
mac_len);
goto out;
}
gso_partial = !!(skb_shinfo(segs)->gso_type & SKB_GSO_PARTIAL);
outer_hlen = skb_tnl_header_len(skb);
gre_offset = outer_hlen - tnl_hlen;
skb = segs;
do {
struct gre_base_hdr *greh;
__sum16 *pcsum;
/* Set up inner headers if we are offloading inner checksum */
if (skb->ip_summed == CHECKSUM_PARTIAL) {
skb_reset_inner_headers(skb);
skb->encapsulation = 1;
}
gso: Update tunnel segmentation to support Tx checksum offload This change makes it so that the GRE and VXLAN tunnels can make use of Tx checksum offload support provided by some drivers via the hw_enc_features. Without this fix enabling GSO means sacrificing Tx checksum offload and this actually leads to a performance regression as shown below: Utilization Send Throughput local GSO 10^6bits/s % S state 6276.51 8.39 enabled 7123.52 8.42 disabled To resolve this it was necessary to address two items. First netif_skb_features needed to be updated so that it would correctly handle the Trans Ether Bridging protocol without impacting the need to check for Q-in-Q tagging. To do this it was necessary to update harmonize_features so that it used skb_network_protocol instead of just using the outer protocol. Second it was necessary to update the GRE and UDP tunnel segmentation offloads so that they would reset the encapsulation bit and inner header offsets after the offload was complete. As a result of this change I have seen the following results on a interface with Tx checksum enabled for encapsulated frames: Utilization Send Throughput local GSO 10^6bits/s % S state 7123.52 8.42 disabled 8321.75 5.43 enabled v2: Instead of replacing refrence to skb->protocol with skb_network_protocol just replace the protocol reference in harmonize_features to allow for double VLAN tag checks. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-11 08:05:06 +08:00
skb->mac_len = mac_len;
skb->protocol = protocol;
__skb_push(skb, outer_hlen);
skb_reset_mac_header(skb);
skb_set_network_header(skb, mac_len);
skb_set_transport_header(skb, gre_offset);
if (!need_csum)
continue;
greh = (struct gre_base_hdr *)skb_transport_header(skb);
pcsum = (__sum16 *)(greh + 1);
if (gso_partial && skb_is_gso(skb)) {
unsigned int partial_adj;
/* Adjust checksum to account for the fact that
* the partial checksum is based on actual size
* whereas headers should be based on MSS size.
*/
partial_adj = skb->len + skb_headroom(skb) -
SKB_GSO_CB(skb)->data_offset -
skb_shinfo(skb)->gso_size;
*pcsum = ~csum_fold((__force __wsum)htonl(partial_adj));
} else {
*pcsum = 0;
}
*(pcsum + 1) = 0;
*pcsum = gso_make_checksum(skb, 0);
} while ((skb = skb->next));
out:
return segs;
}
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
static struct sk_buff **gre_gro_receive(struct sk_buff **head,
struct sk_buff *skb)
{
struct sk_buff **pp = NULL;
struct sk_buff *p;
const struct gre_base_hdr *greh;
unsigned int hlen, grehlen;
unsigned int off;
int flush = 1;
struct packet_offload *ptype;
__be16 type;
if (NAPI_GRO_CB(skb)->encap_mark)
goto out;
NAPI_GRO_CB(skb)->encap_mark = 1;
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
off = skb_gro_offset(skb);
hlen = off + sizeof(*greh);
greh = skb_gro_header_fast(skb, off);
if (skb_gro_header_hard(skb, hlen)) {
greh = skb_gro_header_slow(skb, hlen, off);
if (unlikely(!greh))
goto out;
}
/* Only support version 0 and K (key), C (csum) flags. Note that
* although the support for the S (seq#) flag can be added easily
* for GRO, this is problematic for GSO hence can not be enabled
* here because a GRO pkt may end up in the forwarding path, thus
* requiring GSO support to break it up correctly.
*/
if ((greh->flags & ~(GRE_KEY|GRE_CSUM)) != 0)
goto out;
/* We can only support GRE_CSUM if we can track the location of
* the GRE header. In the case of FOU/GUE we cannot because the
* outer UDP header displaces the GRE header leaving us in a state
* of limbo.
*/
if ((greh->flags & GRE_CSUM) && NAPI_GRO_CB(skb)->is_fou)
goto out;
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
type = greh->protocol;
rcu_read_lock();
ptype = gro_find_receive_by_type(type);
if (!ptype)
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
goto out_unlock;
grehlen = GRE_HEADER_SECTION;
if (greh->flags & GRE_KEY)
grehlen += GRE_HEADER_SECTION;
if (greh->flags & GRE_CSUM)
grehlen += GRE_HEADER_SECTION;
hlen = off + grehlen;
if (skb_gro_header_hard(skb, hlen)) {
greh = skb_gro_header_slow(skb, hlen, off);
if (unlikely(!greh))
goto out_unlock;
}
/* Don't bother verifying checksum if we're going to flush anyway. */
if ((greh->flags & GRE_CSUM) && !NAPI_GRO_CB(skb)->flush) {
if (skb_gro_checksum_simple_validate(skb))
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
goto out_unlock;
skb_gro_checksum_try_convert(skb, IPPROTO_GRE, 0,
null_compute_pseudo);
}
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
for (p = *head; p; p = p->next) {
const struct gre_base_hdr *greh2;
if (!NAPI_GRO_CB(p)->same_flow)
continue;
/* The following checks are needed to ensure only pkts
* from the same tunnel are considered for aggregation.
* The criteria for "the same tunnel" includes:
* 1) same version (we only support version 0 here)
* 2) same protocol (we only support ETH_P_IP for now)
* 3) same set of flags
* 4) same key if the key field is present.
*/
greh2 = (struct gre_base_hdr *)(p->data + off);
if (greh2->flags != greh->flags ||
greh2->protocol != greh->protocol) {
NAPI_GRO_CB(p)->same_flow = 0;
continue;
}
if (greh->flags & GRE_KEY) {
/* compare keys */
if (*(__be32 *)(greh2+1) != *(__be32 *)(greh+1)) {
NAPI_GRO_CB(p)->same_flow = 0;
continue;
}
}
}
skb_gro_pull(skb, grehlen);
/* Adjusted NAPI_GRO_CB(skb)->csum after skb_gro_pull()*/
skb_gro_postpull_rcsum(skb, greh, grehlen);
pp = call_gro_receive(ptype->callbacks.gro_receive, head, skb);
flush = 0;
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
out_unlock:
rcu_read_unlock();
out:
NAPI_GRO_CB(skb)->flush |= flush;
return pp;
}
static int gre_gro_complete(struct sk_buff *skb, int nhoff)
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
{
struct gre_base_hdr *greh = (struct gre_base_hdr *)(skb->data + nhoff);
struct packet_offload *ptype;
unsigned int grehlen = sizeof(*greh);
int err = -ENOENT;
__be16 type;
skb->encapsulation = 1;
skb_shinfo(skb)->gso_type = SKB_GSO_GRE;
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
type = greh->protocol;
if (greh->flags & GRE_KEY)
grehlen += GRE_HEADER_SECTION;
if (greh->flags & GRE_CSUM)
grehlen += GRE_HEADER_SECTION;
rcu_read_lock();
ptype = gro_find_complete_by_type(type);
if (ptype)
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
err = ptype->callbacks.gro_complete(skb, nhoff + grehlen);
rcu_read_unlock();
skb_set_inner_mac_header(skb, nhoff + grehlen);
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
return err;
}
static const struct net_offload gre_offload = {
.callbacks = {
.gso_segment = gre_gso_segment,
net-gre-gro: Add GRE support to the GRO stack This patch built on top of Commit 299603e8370a93dd5d8e8d800f0dff1ce2c53d36 ("net-gro: Prepare GRO stack for the upcoming tunneling support") to add the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO stack. It also serves as an example for supporting other encapsulation protocols in the GRO stack in the future. The patch supports version 0 and all the flags (key, csum, seq#) but will flush any pkt with the S (seq#) flag. This is because the S flag is not support by GSO, and a GRO pkt may end up in the forwarding path, thus requiring GSO support to break it up correctly. Currently the "packet_offload" structure only contains L3 (ETH_P_IP/ ETH_P_IPV6) GRO offload support so the encapped pkts are limited to IP pkts (i.e., w/o L2 hdr). But support for other protocol type can be easily added, so is the support for GRE variations like NVGRE. The patch also support csum offload. Specifically if the csum flag is on and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE), the code will take advantage of the csum computed by the h/w when validating the GRE csum. Note that commit 60769a5dcd8755715c7143b4571d5c44f01796f1 "ipv4: gre: add GRO capability" already introduces GRO capability to IPv4 GRE tunnels, using the gro_cells infrastructure. But GRO is done after GRE hdr has been removed (i.e., decapped). The following patch applies GRO when pkts first come in (before hitting the GRE tunnel code). There is some performance advantage for applying GRO as early as possible. Also this approach is transparent to other subsystem like Open vSwitch where GRE decap is handled outside of the IP stack hence making it harder for the gro_cells stuff to apply. On the other hand, some NICs are still not capable of hashing on the inner hdr of a GRE pkt (RSS). In that case the GRO processing of pkts from the same remote host will all happen on the same CPU and the performance may be suboptimal. I'm including some rough preliminary performance numbers below. Note that the performance will be highly dependent on traffic load, mix as usual. Moreover it also depends on NIC offload features hence the following is by no means a comprehesive study. Local testing and tuning will be needed to decide the best setting. All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs. (super_netperf 50 -H 192.168.1.18 -l 30) An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1 mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123) is configured. The GRO support for pkts AFTER decap are controlled through the device feature of the GRE device (e.g., ethtool -K gre1 gro on/off). 1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off thruput: 9.16Gbps CPU utilization: 19% 1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off thruput: 5.9Gbps CPU utilization: 15% 1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 12-13% 1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on thruput: 9.26Gbps CPU utilization: 10% The following tests were performed on a different NIC that is capable of csum offload. I.e., the h/w is capable of computing IP payload csum (CHECKSUM_COMPLETE). 2.1 ethtool -K gre1 gro on (hence will use gro_cells) 2.1.1 ethtool -K eth0 gro off; csum offload disabled thruput: 8.53Gbps CPU utilization: 9% 2.1.2 ethtool -K eth0 gro off; csum offload enabled thruput: 8.97Gbps CPU utilization: 7-8% 2.1.3 ethtool -K eth0 gro on; csum offload disabled thruput: 8.83Gbps CPU utilization: 5-6% 2.1.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.98Gbps CPU utilization: 5% 2.2 ethtool -K gre1 gro off 2.2.1 ethtool -K eth0 gro off; csum offload disabled thruput: 5.93Gbps CPU utilization: 9% 2.2.2 ethtool -K eth0 gro off; csum offload enabled thruput: 5.62Gbps CPU utilization: 8% 2.2.3 ethtool -K eth0 gro on; csum offload disabled thruput: 7.69Gbps CPU utilization: 8% 2.2.4 ethtool -K eth0 gro on; csum offload enabled thruput: 8.96Gbps CPU utilization: 5-6% Signed-off-by: H.K. Jerry Chu <hkchu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-08 02:23:19 +08:00
.gro_receive = gre_gro_receive,
.gro_complete = gre_gro_complete,
},
};
static int __init gre_offload_init(void)
{
int err;
err = inet_add_offload(&gre_offload, IPPROTO_GRE);
#if IS_ENABLED(CONFIG_IPV6)
if (err)
return err;
err = inet6_add_offload(&gre_offload, IPPROTO_GRE);
if (err)
inet_del_offload(&gre_offload, IPPROTO_GRE);
#endif
return err;
}
device_initcall(gre_offload_init);