linux_old1/arch/arm/mach-orion5x/ts78xx-setup.c

/*
 * arch/arm/mach-orion5x/ts78xx-setup.c
 *
 * Maintainer: Alexander Clouter <alex@digriz.org.uk>
 *
 * This file is licensed under the terms of the GNU General Public
 * License version 2.  This program is licensed "as is" without any
 * warranty of any kind, whether express or implied.
 */

#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/sysfs.h>
#include <linux/platform_device.h>
#include <linux/mv643xx_eth.h>
#include <linux/ata_platform.h>
#include <linux/m48t86.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
#include "ts78xx-fpga.h"

/*****************************************************************************
 * TS-78xx Info
 ****************************************************************************/

/*
 * FPGA - lives where the PCI bus would be at ORION5X_PCI_MEM_PHYS_BASE
 */
#define TS78XX_FPGA_REGS_PHYS_BASE	0xe8000000
#define TS78XX_FPGA_REGS_VIRT_BASE	0xff900000
#define TS78XX_FPGA_REGS_SIZE		SZ_1M

static struct ts78xx_fpga_data ts78xx_fpga = {
	.id		= 0,
	.state		= 1,
/*	.supports	= ... - populated by ts78xx_fpga_supports() */
};

/*****************************************************************************
 * I/O Address Mapping
 ****************************************************************************/
static struct map_desc ts78xx_io_desc[] __initdata = {
	{
		.virtual	= TS78XX_FPGA_REGS_VIRT_BASE,
		.pfn		= __phys_to_pfn(TS78XX_FPGA_REGS_PHYS_BASE),
		.length		= TS78XX_FPGA_REGS_SIZE,
		.type		= MT_DEVICE,
	},
};

void __init ts78xx_map_io(void)
{
	orion5x_map_io();
	iotable_init(ts78xx_io_desc, ARRAY_SIZE(ts78xx_io_desc));
}

/*****************************************************************************
 * Ethernet
 ****************************************************************************/
static struct mv643xx_eth_platform_data ts78xx_eth_data = {
	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
};

/*****************************************************************************
 * SATA
 ****************************************************************************/
static struct mv_sata_platform_data ts78xx_sata_data = {
	.n_ports	= 2,
};

/*****************************************************************************
 * RTC M48T86 - nicked^Wborrowed from arch/arm/mach-ep93xx/ts72xx.c
 ****************************************************************************/
#ifdef CONFIG_RTC_DRV_M48T86
#define TS_RTC_CTRL	(TS78XX_FPGA_REGS_VIRT_BASE | 0x808)
#define TS_RTC_DATA	(TS78XX_FPGA_REGS_VIRT_BASE | 0x80c)

static unsigned char ts78xx_ts_rtc_readbyte(unsigned long addr)
{
	writeb(addr, TS_RTC_CTRL);
	return readb(TS_RTC_DATA);
}

static void ts78xx_ts_rtc_writebyte(unsigned char value, unsigned long addr)
{
	writeb(addr, TS_RTC_CTRL);
	writeb(value, TS_RTC_DATA);
}

static struct m48t86_ops ts78xx_ts_rtc_ops = {
	.readbyte	= ts78xx_ts_rtc_readbyte,
	.writebyte	= ts78xx_ts_rtc_writebyte,
};

static struct platform_device ts78xx_ts_rtc_device = {
	.name		= "rtc-m48t86",
	.id		= -1,
	.dev		= {
		.platform_data	= &ts78xx_ts_rtc_ops,
	},
	.num_resources	= 0,
};

/*
 * TS uses some of the user storage space on the RTC chip so see if it is
 * present; as it's an optional feature at purchase time and not all boards
 * will have it present
 *
 * I've used the method TS use in their rtc7800.c example for the detection
 *
 * TODO: track down a guinea pig without an RTC to see if we can work out a
 * 		better RTC detection routine
 */
static int ts78xx_ts_rtc_load(void)
{
	int rc;
	unsigned char tmp_rtc0, tmp_rtc1;

	tmp_rtc0 = ts78xx_ts_rtc_readbyte(126);
	tmp_rtc1 = ts78xx_ts_rtc_readbyte(127);

	ts78xx_ts_rtc_writebyte(0x00, 126);
	ts78xx_ts_rtc_writebyte(0x55, 127);
	if (ts78xx_ts_rtc_readbyte(127) == 0x55) {
		ts78xx_ts_rtc_writebyte(0xaa, 127);
		if (ts78xx_ts_rtc_readbyte(127) == 0xaa
				&& ts78xx_ts_rtc_readbyte(126) == 0x00) {
			ts78xx_ts_rtc_writebyte(tmp_rtc0, 126);
			ts78xx_ts_rtc_writebyte(tmp_rtc1, 127);

			if (ts78xx_fpga.supports.ts_rtc.init == 0) {
				rc = platform_device_register(&ts78xx_ts_rtc_device);
				if (!rc)
					ts78xx_fpga.supports.ts_rtc.init = 1;
			} else
				rc = platform_device_add(&ts78xx_ts_rtc_device);

			return rc;
		}
	}

	return -ENODEV;
};

static void ts78xx_ts_rtc_unload(void)
{
	platform_device_del(&ts78xx_ts_rtc_device);
}
#else
static int ts78xx_ts_rtc_load(void)
{
	return -ENODEV;
}

static void ts78xx_ts_rtc_unload(void)
{
}
#endif

/*****************************************************************************
 * FPGA 'hotplug' support code
 ****************************************************************************/
static void ts78xx_fpga_devices_zero_init(void)
{
	ts78xx_fpga.supports.ts_rtc.init = 0;
}

static void ts78xx_fpga_supports(void)
{
	/* TODO: put this 'table' into ts78xx-fpga.h */
	switch (ts78xx_fpga.id) {
	case TS7800_REV_B:
		ts78xx_fpga.supports.ts_rtc.present = 1;
		break;
	default:
		ts78xx_fpga.supports.ts_rtc.present = 0;
	}
}

static int ts78xx_fpga_load_devices(void)
{
	int tmp, ret = 0;

	if (ts78xx_fpga.supports.ts_rtc.present == 1) {
		tmp = ts78xx_ts_rtc_load();
		if (tmp) {
			printk(KERN_INFO "TS-78xx RTC"
					" not detected or enabled\n");
			ts78xx_fpga.supports.ts_rtc.present = 0;
		}
		ret |= tmp;
	}

	return ret;
}

static int ts78xx_fpga_unload_devices(void)
{
	int ret = 0;

	if (ts78xx_fpga.supports.ts_rtc.present == 1)
		ts78xx_ts_rtc_unload();

	return ret;
}

static int ts78xx_fpga_load(void)
{
	ts78xx_fpga.id = readl(TS78XX_FPGA_REGS_VIRT_BASE);

	printk(KERN_INFO "TS-78xx FPGA: magic=0x%.6x, rev=0x%.2x\n",
			(ts78xx_fpga.id >> 8) & 0xffffff,
			ts78xx_fpga.id & 0xff);

	ts78xx_fpga_supports();

	if (ts78xx_fpga_load_devices()) {
		ts78xx_fpga.state = -1;
		return -EBUSY;
	}

	return 0;
};

static int ts78xx_fpga_unload(void)
{
	unsigned int fpga_id;

	fpga_id = readl(TS78XX_FPGA_REGS_VIRT_BASE);

	/*
	 * There does not seem to be a feasible way to block access to the GPIO
	 * pins from userspace (/dev/mem).  This if clause should hopefully warn
	 * those foolish enough not to follow 'policy' :)
	 *
	 * UrJTAG SVN since r1381 can be used to reprogram the FPGA
	 */
	if (ts78xx_fpga.id != fpga_id) {
		printk(KERN_ERR	"TS-78xx FPGA: magic/rev mismatch\n"
			"TS-78xx FPGA: was 0x%.6x/%.2x but now 0x%.6x/%.2x\n",
			(ts78xx_fpga.id >> 8) & 0xffffff, ts78xx_fpga.id & 0xff,
			(fpga_id >> 8) & 0xffffff, fpga_id & 0xff);
		ts78xx_fpga.state = -1;
		return -EBUSY;
	}

	if (ts78xx_fpga_unload_devices()) {
		ts78xx_fpga.state = -1;
		return -EBUSY;
	}

	return 0;
};

static ssize_t ts78xx_fpga_show(struct kobject *kobj,
			struct kobj_attribute *attr, char *buf)
{
	if (ts78xx_fpga.state < 0)
		return sprintf(buf, "borked\n");

	return sprintf(buf, "%s\n", (ts78xx_fpga.state) ? "online" : "offline");
}

static ssize_t ts78xx_fpga_store(struct kobject *kobj,
			struct kobj_attribute *attr, const char *buf, size_t n)
{
	int value, ret;

	if (ts78xx_fpga.state < 0) {
		printk(KERN_ERR "TS-78xx FPGA: borked, you must powercycle asap\n");
		return -EBUSY;
	}

	if (strncmp(buf, "online", sizeof("online") - 1) == 0)
		value = 1;
	else if (strncmp(buf, "offline", sizeof("offline") - 1) == 0)
		value = 0;
	else {
		printk(KERN_ERR "ts78xx_fpga_store: Invalid value\n");
		return -EINVAL;
	}

	if (ts78xx_fpga.state == value)
		return n;

	ret = (ts78xx_fpga.state == 0)
		? ts78xx_fpga_load()
		: ts78xx_fpga_unload();

	if (!(ret < 0))
		ts78xx_fpga.state = value;

	return n;
}

static struct kobj_attribute ts78xx_fpga_attr =
	__ATTR(ts78xx_fpga, 0644, ts78xx_fpga_show, ts78xx_fpga_store);

/*****************************************************************************
 * General Setup
 ****************************************************************************/
static struct orion5x_mpp_mode ts78xx_mpp_modes[] __initdata = {
	{  0, MPP_UNUSED },
	{  1, MPP_GPIO },		/* JTAG Clock */
	{  2, MPP_GPIO },		/* JTAG Data In */
	{  3, MPP_GPIO },		/* Lat ECP2 256 FPGA - PB2B */
	{  4, MPP_GPIO },		/* JTAG Data Out */
	{  5, MPP_GPIO },		/* JTAG TMS */
	{  6, MPP_GPIO },		/* Lat ECP2 256 FPGA - PB31A_CLK4+ */
	{  7, MPP_GPIO },		/* Lat ECP2 256 FPGA - PB22B */
	{  8, MPP_UNUSED },
	{  9, MPP_UNUSED },
	{ 10, MPP_UNUSED },
	{ 11, MPP_UNUSED },
	{ 12, MPP_UNUSED },
	{ 13, MPP_UNUSED },
	{ 14, MPP_UNUSED },
	{ 15, MPP_UNUSED },
	{ 16, MPP_UART },
	{ 17, MPP_UART },
	{ 18, MPP_UART },
	{ 19, MPP_UART },
	/*
	 * MPP[20] PCI Clock Out 1
	 * MPP[21] PCI Clock Out 0
	 * MPP[22] Unused
	 * MPP[23] Unused
	 * MPP[24] Unused
	 * MPP[25] Unused
	 */
	{ -1 },
};

static void __init ts78xx_init(void)
{
	int ret;

	/*
	 * Setup basic Orion functions. Need to be called early.
	 */
	orion5x_init();

	orion5x_mpp_conf(ts78xx_mpp_modes);

	/*
	 * Configure peripherals.
	 */
	orion5x_ehci0_init();
	orion5x_ehci1_init();
	orion5x_eth_init(&ts78xx_eth_data);
	orion5x_sata_init(&ts78xx_sata_data);
	orion5x_uart0_init();
	orion5x_uart1_init();
	orion5x_xor_init();

	/* FPGA init */
	ts78xx_fpga_devices_zero_init();
	ret = ts78xx_fpga_load();
	ret = sysfs_create_file(power_kobj, &ts78xx_fpga_attr.attr);
	if (ret)
		printk(KERN_ERR "sysfs_create_file failed: %d\n", ret);
}

MACHINE_START(TS78XX, "Technologic Systems TS-78xx SBC")
	/* Maintainer: Alexander Clouter <alex@digriz.org.uk> */
	.phys_io	= ORION5X_REGS_PHYS_BASE,
	.io_pg_offst	= ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC,
	.boot_params	= 0x00000100,
	.init_machine	= ts78xx_init,
	.map_io		= ts78xx_map_io,
	.init_irq	= orion5x_init_irq,
	.timer		= &orion5x_timer,
MACHINE_END