diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
index c7db42d6b3bc..d3a1e7104556 100644
--- a/drivers/spi/spi-imx.c
+++ b/drivers/spi/spi-imx.c
@@ -490,14 +490,9 @@ static void mx51_ecspi_disable(struct spi_imx_data *spi_imx)
 static int mx51_ecspi_prepare_message(struct spi_imx_data *spi_imx,
 				      struct spi_message *msg)
 {
-	return 0;
-}
-
-static int mx51_ecspi_config(struct spi_device *spi)
-{
-	struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
+	struct spi_device *spi = msg->spi;
 	u32 ctrl = MX51_ECSPI_CTRL_ENABLE;
-	u32 clk = spi_imx->speed_hz, delay, reg;
+	u32 testreg;
 	u32 cfg = readl(spi_imx->base + MX51_ECSPI_CONFIG);
 
 	/* set Master or Slave mode */
@@ -512,19 +507,21 @@ static int mx51_ecspi_config(struct spi_device *spi)
 	if (spi->mode & SPI_READY)
 		ctrl |= MX51_ECSPI_CTRL_DRCTL(spi_imx->spi_drctl);
 
-	/* set clock speed */
-	ctrl |= mx51_ecspi_clkdiv(spi_imx, spi_imx->speed_hz, &clk);
-	spi_imx->spi_bus_clk = clk;
-
 	/* set chip select to use */
 	ctrl |= MX51_ECSPI_CTRL_CS(spi->chip_select);
 
-	if (spi_imx->slave_mode && is_imx53_ecspi(spi_imx))
-		ctrl |= (spi_imx->slave_burst * 8 - 1)
-			<< MX51_ECSPI_CTRL_BL_OFFSET;
+	/*
+	 * The ctrl register must be written first, with the EN bit set other
+	 * registers must not be written to.
+	 */
+	writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
+
+	testreg = readl(spi_imx->base + MX51_ECSPI_TESTREG);
+	if (spi->mode & SPI_LOOP)
+		testreg |= MX51_ECSPI_TESTREG_LBC;
 	else
-		ctrl |= (spi_imx->bits_per_word - 1)
-			<< MX51_ECSPI_CTRL_BL_OFFSET;
+		testreg &= ~MX51_ECSPI_TESTREG_LBC;
+	writel(testreg, spi_imx->base + MX51_ECSPI_TESTREG);
 
 	/*
 	 * eCSPI burst completion by Chip Select signal in Slave mode
@@ -548,26 +545,43 @@ static int mx51_ecspi_config(struct spi_device *spi)
 		cfg &= ~MX51_ECSPI_CONFIG_SCLKPOL(spi->chip_select);
 		cfg &= ~MX51_ECSPI_CONFIG_SCLKCTL(spi->chip_select);
 	}
+
 	if (spi->mode & SPI_CS_HIGH)
 		cfg |= MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
 	else
 		cfg &= ~MX51_ECSPI_CONFIG_SSBPOL(spi->chip_select);
 
+	writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG);
+
+	return 0;
+}
+
+static int mx51_ecspi_config(struct spi_device *spi)
+{
+	struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
+	u32 ctrl = readl(spi_imx->base + MX51_ECSPI_CTRL);
+	u32 clk = spi_imx->speed_hz, delay;
+
+	/* Clear BL field and set the right value */
+	ctrl &= ~MX51_ECSPI_CTRL_BL_MASK;
+	if (spi_imx->slave_mode && is_imx53_ecspi(spi_imx))
+		ctrl |= (spi_imx->slave_burst * 8 - 1)
+			<< MX51_ECSPI_CTRL_BL_OFFSET;
+	else
+		ctrl |= (spi_imx->bits_per_word - 1)
+			<< MX51_ECSPI_CTRL_BL_OFFSET;
+
+	/* set clock speed */
+	ctrl &= ~(0xf << MX51_ECSPI_CTRL_POSTDIV_OFFSET |
+		  0xf << MX51_ECSPI_CTRL_PREDIV_OFFSET);
+	ctrl |= mx51_ecspi_clkdiv(spi_imx, spi_imx->speed_hz, &clk);
+	spi_imx->spi_bus_clk = clk;
+
 	if (spi_imx->usedma)
 		ctrl |= MX51_ECSPI_CTRL_SMC;
 
-	/* CTRL register always go first to bring out controller from reset */
 	writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
 
-	reg = readl(spi_imx->base + MX51_ECSPI_TESTREG);
-	if (spi->mode & SPI_LOOP)
-		reg |= MX51_ECSPI_TESTREG_LBC;
-	else
-		reg &= ~MX51_ECSPI_TESTREG_LBC;
-	writel(reg, spi_imx->base + MX51_ECSPI_TESTREG);
-
-	writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG);
-
 	/*
 	 * Wait until the changes in the configuration register CONFIGREG
 	 * propagate into the hardware. It takes exactly one tick of the
@@ -594,7 +608,6 @@ static void mx51_setup_wml(struct spi_imx_data *spi_imx)
 	 * Configure the DMA register: setup the watermark
 	 * and enable DMA request.
 	 */
-
 	writel(MX51_ECSPI_DMA_RX_WML(spi_imx->wml - 1) |
 		MX51_ECSPI_DMA_TX_WML(spi_imx->wml) |
 		MX51_ECSPI_DMA_RXT_WML(spi_imx->wml) |