From 88a748419b84187fd1da05637b8e5928b04a1e06 Mon Sep 17 00:00:00 2001 From: Faiz Abbas Date: Thu, 2 May 2019 14:17:48 +0530 Subject: [PATCH 1/2] ARM: dts: am57xx-idk: Remove support for voltage switching for SD card If UHS speed modes are enabled, a compatible SD card switches down to 1.8V during enumeration. If after this a software reboot/crash takes place and on-chip ROM tries to enumerate the SD card, the difference in IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card. The fix for this is to have support for power cycling the card in hardware (with a PORz/soft-reset line causing a power cycle of the card). Since am571x-, am572x- and am574x-idk don't have this capability, disable voltage switching for these boards. The major effect of this is that the maximum supported speed mode is now high speed(50 MHz) down from SDR104(200 MHz). Cc: Signed-off-by: Faiz Abbas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am57xx-idk-common.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/am57xx-idk-common.dtsi b/arch/arm/boot/dts/am57xx-idk-common.dtsi index f7bd26458915..42e433da79ec 100644 --- a/arch/arm/boot/dts/am57xx-idk-common.dtsi +++ b/arch/arm/boot/dts/am57xx-idk-common.dtsi @@ -420,6 +420,7 @@ &mmc1 { vqmmc-supply = <&ldo1_reg>; bus-width = <4>; cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */ + no-1-8-v; }; &mmc2 { From c3c0b70cd3f801bded7a548198ee1c9851a0ca82 Mon Sep 17 00:00:00 2001 From: Faiz Abbas Date: Tue, 30 Apr 2019 11:38:56 +0530 Subject: [PATCH 2/2] ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values Update the MMC2_HS200_MANUAL1 iodelay values to match with the latest dra76x data manual[1]. The new iodelay values will have better marginality and should prevent issues in corner cases. Also this particular pinctrl-array is using spaces instead of tabs for spacing between the values and the comments. Fix this as well. [1] http://www.ti.com/lit/ds/symlink/dra76p.pdf Cc: Signed-off-by: Faiz Abbas [tony@atomide.com: updated description with a bit more info] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra76x-mmc-iodelay.dtsi | 40 +++++++++++------------ 1 file changed, 20 insertions(+), 20 deletions(-) diff --git a/arch/arm/boot/dts/dra76x-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra76x-mmc-iodelay.dtsi index baba7b00eca7..fdca48186916 100644 --- a/arch/arm/boot/dts/dra76x-mmc-iodelay.dtsi +++ b/arch/arm/boot/dts/dra76x-mmc-iodelay.dtsi @@ -22,7 +22,7 @@ * * Datamanual Revisions: * - * DRA76x Silicon Revision 1.0: SPRS993A, Revised July 2017 + * DRA76x Silicon Revision 1.0: SPRS993E, Revised December 2018 * */ @@ -169,25 +169,25 @@ mmc1_iodelay_sdr104_conf: mmc1_iodelay_sdr104_conf { /* Corresponds to MMC2_HS200_MANUAL1 in datamanual */ mmc2_iodelay_hs200_conf: mmc2_iodelay_hs200_conf { pinctrl-pin-array = < - 0x190 A_DELAY_PS(384) G_DELAY_PS(0) /* CFG_GPMC_A19_OEN */ - 0x194 A_DELAY_PS(0) G_DELAY_PS(174) /* CFG_GPMC_A19_OUT */ - 0x1a8 A_DELAY_PS(410) G_DELAY_PS(0) /* CFG_GPMC_A20_OEN */ - 0x1ac A_DELAY_PS(85) G_DELAY_PS(0) /* CFG_GPMC_A20_OUT */ - 0x1b4 A_DELAY_PS(468) G_DELAY_PS(0) /* CFG_GPMC_A21_OEN */ - 0x1b8 A_DELAY_PS(139) G_DELAY_PS(0) /* CFG_GPMC_A21_OUT */ - 0x1c0 A_DELAY_PS(676) G_DELAY_PS(0) /* CFG_GPMC_A22_OEN */ - 0x1c4 A_DELAY_PS(69) G_DELAY_PS(0) /* CFG_GPMC_A22_OUT */ - 0x1d0 A_DELAY_PS(1062) G_DELAY_PS(154) /* CFG_GPMC_A23_OUT */ - 0x1d8 A_DELAY_PS(640) G_DELAY_PS(0) /* CFG_GPMC_A24_OEN */ - 0x1dc A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_GPMC_A24_OUT */ - 0x1e4 A_DELAY_PS(356) G_DELAY_PS(0) /* CFG_GPMC_A25_OEN */ - 0x1e8 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_GPMC_A25_OUT */ - 0x1f0 A_DELAY_PS(579) G_DELAY_PS(0) /* CFG_GPMC_A26_OEN */ - 0x1f4 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_GPMC_A26_OUT */ - 0x1fc A_DELAY_PS(435) G_DELAY_PS(0) /* CFG_GPMC_A27_OEN */ - 0x200 A_DELAY_PS(36) G_DELAY_PS(0) /* CFG_GPMC_A27_OUT */ - 0x364 A_DELAY_PS(759) G_DELAY_PS(0) /* CFG_GPMC_CS1_OEN */ - 0x368 A_DELAY_PS(72) G_DELAY_PS(0) /* CFG_GPMC_CS1_OUT */ + 0x190 A_DELAY_PS(384) G_DELAY_PS(0) /* CFG_GPMC_A19_OEN */ + 0x194 A_DELAY_PS(350) G_DELAY_PS(174) /* CFG_GPMC_A19_OUT */ + 0x1a8 A_DELAY_PS(410) G_DELAY_PS(0) /* CFG_GPMC_A20_OEN */ + 0x1ac A_DELAY_PS(335) G_DELAY_PS(0) /* CFG_GPMC_A20_OUT */ + 0x1b4 A_DELAY_PS(468) G_DELAY_PS(0) /* CFG_GPMC_A21_OEN */ + 0x1b8 A_DELAY_PS(339) G_DELAY_PS(0) /* CFG_GPMC_A21_OUT */ + 0x1c0 A_DELAY_PS(676) G_DELAY_PS(0) /* CFG_GPMC_A22_OEN */ + 0x1c4 A_DELAY_PS(219) G_DELAY_PS(0) /* CFG_GPMC_A22_OUT */ + 0x1d0 A_DELAY_PS(1062) G_DELAY_PS(154) /* CFG_GPMC_A23_OUT */ + 0x1d8 A_DELAY_PS(640) G_DELAY_PS(0) /* CFG_GPMC_A24_OEN */ + 0x1dc A_DELAY_PS(150) G_DELAY_PS(0) /* CFG_GPMC_A24_OUT */ + 0x1e4 A_DELAY_PS(356) G_DELAY_PS(0) /* CFG_GPMC_A25_OEN */ + 0x1e8 A_DELAY_PS(150) G_DELAY_PS(0) /* CFG_GPMC_A25_OUT */ + 0x1f0 A_DELAY_PS(579) G_DELAY_PS(0) /* CFG_GPMC_A26_OEN */ + 0x1f4 A_DELAY_PS(200) G_DELAY_PS(0) /* CFG_GPMC_A26_OUT */ + 0x1fc A_DELAY_PS(435) G_DELAY_PS(0) /* CFG_GPMC_A27_OEN */ + 0x200 A_DELAY_PS(236) G_DELAY_PS(0) /* CFG_GPMC_A27_OUT */ + 0x364 A_DELAY_PS(759) G_DELAY_PS(0) /* CFG_GPMC_CS1_OEN */ + 0x368 A_DELAY_PS(372) G_DELAY_PS(0) /* CFG_GPMC_CS1_OUT */ >; };