p71924506
/
linux_old1
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity

usb: phy: msm: Manual PHY and LINK controller VBUS change notification 

VBUS is not routed to USB PHY on recent Qualcomm platforms. USB controller
must see VBUS in order to pull-up DP when setting RS bit. Henc configure
USB PHY and LINK registers sense VBUS and enable manual pullup on D+ line.

Cc: Vamsi Krishna <vskrishn@codeaurora.org>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit is contained in:
Ivan T. Ivanov 2015-04-09 11:34:33 +03:00 committed by Felipe Balbi
parent 591fc116f3
commit 44e42ae3a3
4 changed files with 44 additions and 0 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

4
Documentation/devicetree/bindings/usb/msm-hsusb.txt
View File

@ -69,6 +69,10 @@ Optional properties:
(no, min, max) where each value represents either a voltage
in microvolts or a value corresponding to voltage corner.
- qcom,manual-pullup: If present, vbus is not routed to USB controller/phy
and controller driver therefore enables pull-up explicitly
before starting controller using usbcmd run/stop bit.
- extcon: phandles to external connector devices. First phandle
should point to external connector, which provide "USB"
cable events, the second should point to external connector

26
drivers/usb/phy/phy-msm-usb.c
View File

@ -240,8 +240,14 @@ static void ulpi_init(struct msm_otg *motg)
static int msm_phy_notify_disconnect(struct usb_phy *phy,
enum usb_device_speed speed)
{
struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
int val;
if (motg->manual_pullup) {
val = ULPI_MISC_A_VBUSVLDEXT | ULPI_MISC_A_VBUSVLDEXTSEL;
usb_phy_io_write(phy, val, ULPI_CLR(ULPI_MISC_A));
}
/*
* Put the transceiver in non-driving mode. Otherwise host
* may not detect soft-disconnection.
@ -422,6 +428,24 @@ static int msm_phy_init(struct usb_phy *phy)
ulpi_write(phy, ulpi_val, ULPI_USB_INT_EN_FALL);
}
if (motg->manual_pullup) {
val = ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT;
ulpi_write(phy, val, ULPI_SET(ULPI_MISC_A));
val = readl(USB_GENCONFIG_2);
val |= GENCONFIG_2_SESS_VLD_CTRL_EN;
writel(val, USB_GENCONFIG_2);
val = readl(USB_USBCMD);
val |= USBCMD_SESS_VLD_CTRL;
writel(val, USB_USBCMD);
val = ulpi_read(phy, ULPI_FUNC_CTRL);
val &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
val |= ULPI_FUNC_CTRL_OPMODE_NORMAL;
ulpi_write(phy, val, ULPI_FUNC_CTRL);
}
if (motg->phy_number)
writel(readl(USB_PHY_CTRL2) | BIT(16), USB_PHY_CTRL2);
@ -1520,6 +1544,8 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)
motg->vdd_levels[VDD_LEVEL_MAX] = tmp[VDD_LEVEL_MAX];
}
motg->manual_pullup = of_property_read_bool(node, "qcom,manual-pullup");
ext_id = ERR_PTR(-ENODEV);
ext_vbus = ERR_PTR(-ENODEV);
if (of_property_read_bool(node, "extcon")) {

5
include/linux/usb/msm_hsusb.h
View File

@ -150,6 +150,9 @@ struct msm_usb_cable {
* @chg_type: The type of charger attached.
* @dcd_retires: The retry count used to track Data contact
* detection process.
* @manual_pullup: true if VBUS is not routed to USB controller/phy
* and controller driver therefore enables pull-up explicitly before
* starting controller using usbcmd run/stop bit.
* @vbus: VBUS signal state trakining, using extcon framework
* @id: ID signal state trakining, using extcon framework
*/
@ -181,6 +184,8 @@ struct msm_otg {
struct reset_control *link_rst;
int vdd_levels[3];
bool manual_pullup;
struct msm_usb_cable vbus;
struct msm_usb_cable id;
};

9
include/linux/usb/msm_hsusb_hw.h
View File

@ -21,6 +21,8 @@
#define USB_AHBBURST (MSM_USB_BASE + 0x0090)
#define USB_AHBMODE (MSM_USB_BASE + 0x0098)
#define USB_GENCONFIG_2 (MSM_USB_BASE + 0x00a0)
#define USB_CAPLENGTH (MSM_USB_BASE + 0x0100) /* 8 bit */
#define USB_USBCMD (MSM_USB_BASE + 0x0140)
@ -30,6 +32,9 @@
#define USB_PHY_CTRL (MSM_USB_BASE + 0x0240)
#define USB_PHY_CTRL2 (MSM_USB_BASE + 0x0278)
#define GENCONFIG_2_SESS_VLD_CTRL_EN BIT(7)
#define USBCMD_SESS_VLD_CTRL BIT(25)
#define USBCMD_RESET 2
#define USB_USBINTR (MSM_USB_BASE + 0x0148)
@ -50,6 +55,10 @@
#define ULPI_PWR_CLK_MNG_REG 0x88
#define OTG_COMP_DISABLE BIT(0)
#define ULPI_MISC_A 0x96
#define ULPI_MISC_A_VBUSVLDEXTSEL BIT(1)
#define ULPI_MISC_A_VBUSVLDEXT BIT(0)
#define ASYNC_INTR_CTRL (1 << 29) /* Enable async interrupt */
#define ULPI_STP_CTRL (1 << 30) /* Block communication with PHY */
#define PHY_RETEN (1 << 1) /* PHY retention enable/disable */