p71924506
/
linux_old1
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity

TTY/Serial patches for 5.1-rc1 

Here is the "big" patchset for the tty/serial driver layer for 5.1-rc1.
 
 It's really not all that big, nothing major here.
 
 There are a lot of tiny driver fixes and updates, combined with other
 cleanups for different serial drivers and the vt layer.  Full details
 are in the shortlog.
 
 All of these have been in linux-next with no reported issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+g7A8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ymoRgCgy8MZ6vayopxNdRBnp4mMmgtaVYMAoMIPYq0V
 XuhV/ZSENWdef2QuaJ3O
 =nSZk
 -----END PGP SIGNATURE-----

Merge tag 'tty-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

Pull tty/serial updates from Greg KH:
 "Here is the "big" patchset for the tty/serial driver layer for
  5.1-rc1.

  It's really not all that big, nothing major here.

  There are a lot of tiny driver fixes and updates, combined with other
  cleanups for different serial drivers and the vt layer. Full details
  are in the shortlog.

  All of these have been in linux-next with no reported issues"

* tag 'tty-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (70 commits)
  tty: xilinx_uartps: Correct return value in probe
  serial: sprd: Modify the baud rate calculation formula
  dt-bindings: serial: Add Milbeaut serial driver description
  serial: 8250_of: assume reg-shift of 2 for mrvl,mmp-uart
  serial: 8250_pxa: honor the port number from devicetree
  tty: hvc_xen: Mark expected switch fall-through
  tty: n_gsm: Mark expected switch fall-throughs
  tty: serial: msm_serial: Remove __init from msm_console_setup()
  tty: serial: samsung: Enable baud clock during initialisation
  serial: uartps: Fix stuck ISR if RX disabled with non-empty FIFO
  tty: serial: remove redundant likely annotation
  tty/n_hdlc: mark expected switch fall-through
  serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()
  serial: 8250_pci: Fix number of ports for ACCES serial cards
  vt: perform safe console erase in the right order
  tty/nozomi: use pci_iomap instead of ioremap_nocache
  tty/synclink: remove ISA support
  serial: 8250_pci: Replace custom code with pci_match_id()
  serial: max310x: Correction of the initial setting of the MODE1 bits for various supported ICs.
  serial: mps2-uart: Add parentheses around conditional in mps2_uart_shutdown
  ...
This commit is contained in:
Linus Torvalds 2019-03-06 16:35:12 -08:00
parent e266ca36da f694936c3b
commit 67e79a6dc2
50 changed files with 1672 additions and 772 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

1
Documentation/devicetree/bindings/serial/8250.txt
View File

@ -21,6 +21,7 @@ Required properties:
- "altr,16550-FIFO128"
- "fsl,16550-FIFO64"
- "fsl,ns16550"
- "intel,xscale-uart"
- "ti,da830-uart"
- "aspeed,ast2400-vuart"
- "aspeed,ast2500-vuart"

3
Documentation/devicetree/bindings/serial/ingenic,uart.txt
View File

@ -6,7 +6,8 @@ Required properties:
- "ingenic,jz4760-uart",
- "ingenic,jz4770-uart",
- "ingenic,jz4775-uart",
- "ingenic,jz4780-uart".
- "ingenic,jz4780-uart",
- "ingenic,x1000-uart".
- reg : offset and length of the register set for the device.
- interrupts : should contain uart interrupt.
- clocks : phandles to the module & baud clocks.

21
Documentation/devicetree/bindings/serial/milbeaut-uart.txt Normal file
View File

@ -0,0 +1,21 @@
Socionext Milbeaut UART controller
Required properties:
- compatible: should be "socionext,milbeaut-usio-uart".
- reg: offset and length of the register set for the device.
- interrupts: two interrupts specifier.
- interrupt-names: should be "rx", "tx".
- clocks: phandle to the input clock.
Optional properties:
- auto-flow-control: flow control enable.
Example:
usio1: usio_uart@1e700010 {
compatible = "socionext,milbeaut-usio-uart";
reg = <0x1e700010 0x10>;
interrupts = <0 141 0x4>, <0 149 0x4>;
interrupt-names = "rx", "tx";
clocks = <&clk 2>;
auto-flow-control;
};

35
Documentation/devicetree/bindings/serial/nvidia,tegra194-tcu.txt Normal file
View File

@ -0,0 +1,35 @@
NVIDIA Tegra Combined UART (TCU)
The TCU is a system for sharing a hardware UART instance among multiple
systems within the Tegra SoC. It is implemented through a mailbox-
based protocol where each "virtual UART" has a pair of mailboxes, one
for transmitting and one for receiving, that is used to communicate
with the hardware implementing the TCU.
Required properties:
- name : Should be tcu
- compatible
Array of strings
One of:
- "nvidia,tegra194-tcu"
- mbox-names:
"rx" - Mailbox for receiving data from hardware UART
"tx" - Mailbox for transmitting data to hardware UART
- mboxes: Mailboxes corresponding to the mbox-names.
This node is a mailbox consumer. See the following files for details of
the mailbox subsystem, and the specifiers implemented by the relevant
provider(s):
- .../mailbox/mailbox.txt
- .../mailbox/nvidia,tegra186-hsp.txt
Example bindings:
-----------------
tcu: tcu {
compatible = "nvidia,tegra194-tcu";
mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_SM 0>,
<&hsp_aon TEGRA_HSP_MBOX_TYPE_SM 1>;
mbox-names = "rx", "tx";
};

2
Documentation/devicetree/bindings/serial/omap_serial.txt
View File

@ -22,6 +22,8 @@ Optional properties:
- dma-names : "rx" for receive channel, "tx" for transmit channel.
- rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt
- rs485-rts-active-high: drive RTS high when sending (default is low).
- clocks: phandle to the functional clock as per
Documentation/devicetree/bindings/clock/clock-bindings.txt
Example:

51
Documentation/devicetree/bindings/serial/pl011.txt
View File

@ -1,51 +0,0 @@
* ARM AMBA Primecell PL011 serial UART
Required properties:
- compatible: must be "arm,primecell", "arm,pl011", "zte,zx296702-uart"
- reg: exactly one register range with length 0x1000
- interrupts: exactly one interrupt specifier
Optional properties:
- pinctrl:
When present, must have one state named "default",
and may contain a second name named "sleep". The former
state sets up pins for ordinary operation whereas
the latter state will put the associated pins to sleep
when the UART is unused
- clocks:
When present, the first clock listed must correspond to
the clock named UARTCLK on the IP block, i.e. the clock
to the external serial line, whereas the second clock
must correspond to the PCLK clocking the internal logic
of the block. Just listing one clock (the first one) is
deprecated.
- clock-names:
When present, the first clock listed must be named
"uartclk" and the second clock listed must be named
"apb_pclk"
- dmas:
When present, may have one or two dma channels.
The first one must be named "rx", the second one
must be named "tx".
- auto-poll:
Enables polling when using RX DMA.
- poll-rate-ms:
Rate at which poll occurs when auto-poll is set,
default 100ms.
- poll-timeout-ms:
Poll timeout when auto-poll is set, default
3000ms.
See also bindings/arm/primecell.txt
Example:
uart@80120000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x80120000 0x1000>;
interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dma 13 0 0x2>, <&dma 13 0 0x0>;
dma-names = "rx", "tx";
clocks = <&foo_clk>, <&bar_clk>;
clock-names = "uartclk", "apb_pclk";
};

126
Documentation/devicetree/bindings/serial/pl011.yaml Normal file
View File

@ -0,0 +1,126 @@
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/serial/pl011.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: ARM AMBA Primecell PL011 serial UART
maintainers:
- Rob Herring <robh@kernel.org>
allOf:
- $ref: /schemas/serial.yaml#
# Need a custom select here or 'arm,primecell' will match on lots of nodes
select:
properties:
compatible:
contains:
enum:
- arm,pl011
- zte,zx296702-uart
required:
- compatible
properties:
compatible:
oneOf:
- items:
- const: arm,pl011
- const: arm,primecell
- items:
- const: zte,zx296702-uart
- const: arm,primecell
reg:
maxItems: 1
interrupts:
maxItems: 1
pinctrl-0: true
pinctrl-1: true
pinctrl-names:
description:
When present, must have one state named "default",
and may contain a second name named "sleep". The former
state sets up pins for ordinary operation whereas
the latter state will put the associated pins to sleep
when the UART is unused
minItems: 1
items:
- const: default
- const: sleep
clocks:
description:
When present, the first clock listed must correspond to
the clock named UARTCLK on the IP block, i.e. the clock
to the external serial line, whereas the second clock
must correspond to the PCLK clocking the internal logic
of the block. Just listing one clock (the first one) is
deprecated.
maxItems: 2
clock-names:
items:
- const: uartclk
- const: apb_pclk
dmas:
minItems: 1
maxItems: 2
dma-names:
minItems: 1
items:
- const: rx
- const: tx
auto-poll:
description:
Enables polling when using RX DMA.
type: boolean
poll-rate-ms:
description:
Rate at which poll occurs when auto-poll is set.
default 100ms.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- default: 100
poll-timeout-ms:
description:
Poll timeout when auto-poll is set, default
3000ms.
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- default: 3000
required:
- compatible
- reg
- interrupts
dependencies:
poll-rate-ms: [ auto-poll ]
poll-timeout-ms: [ auto-poll ]
additionalProperties: false
examples:
- |
serial@80120000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x80120000 0x1000>;
interrupts = <0 11 4>;
dmas = <&dma 13 0 0x2>, <&dma 13 0 0x0>;
dma-names = "rx", "tx";
clocks = <&foo_clk>, <&bar_clk>;
clock-names = "uartclk", "apb_pclk";
};
...

10
Documentation/devicetree/bindings/serial/renesas,rzn1-uart.txt
View File

@ -1,10 +0,0 @@
Renesas RZ/N1 UART
This controller is based on the Synopsys DesignWare ABP UART and inherits all
properties defined in snps-dw-apb-uart.txt except for the compatible property.
Required properties:
- compatible : The device specific string followed by the generic RZ/N1 string.
Therefore it must be one of:
"renesas,r9a06g032-uart", "renesas,rzn1-uart"
"renesas,r9a06g033-uart", "renesas,rzn1-uart"

2
Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
View File

@ -29,7 +29,9 @@ Required properties:
- "renesas,scif-r8a774c0" for R8A774C0 (RZ/G2E) SCIF compatible UART.
- "renesas,hscif-r8a774c0" for R8A774C0 (RZ/G2E) HSCIF compatible UART.
- "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART.
- "renesas,hscif-r8a7778" for R8A7778 (R-Car M1) HSCIF compatible UART.
- "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART.
- "renesas,hscif-r8a7779" for R8A7779 (R-Car H1) HSCIF compatible UART.
- "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART.
- "renesas,scifa-r8a7790" for R8A7790 (R-Car H2) SCIFA compatible UART.
- "renesas,scifb-r8a7790" for R8A7790 (R-Car H2) SCIFB compatible UART.

76
Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
View File

@ -1,76 +0,0 @@
* Synopsys DesignWare ABP UART
Required properties:
- compatible : "snps,dw-apb-uart"
- reg : offset and length of the register set for the device.
- interrupts : should contain uart interrupt.
Clock handling:
The clock rate of the input clock needs to be supplied by one of
- clock-frequency : the input clock frequency for the UART.
- clocks : phandle to the input clock
The supplying peripheral clock can also be handled, needing a second property
- clock-names: tuple listing input clock names.
Required elements: "baudclk", "apb_pclk"
Optional properties:
- snps,uart-16550-compatible : reflects the value of UART_16550_COMPATIBLE
configuration parameter. Define this if your UART does not implement the busy
functionality.
- resets : phandle to the parent reset controller.
- reg-shift : quantity to shift the register offsets by. If this property is
not present then the register offsets are not shifted.
- reg-io-width : the size (in bytes) of the IO accesses that should be
performed on the device. If this property is not present then single byte
accesses are used.
- dcd-override : Override the DCD modem status signal. This signal will always
be reported as active instead of being obtained from the modem status
register. Define this if your serial port does not use this pin.
- dsr-override : Override the DTS modem status signal. This signal will always
be reported as active instead of being obtained from the modem status
register. Define this if your serial port does not use this pin.
- cts-override : Override the CTS modem status signal. This signal will always
be reported as active instead of being obtained from the modem status
register. Define this if your serial port does not use this pin.
- ri-override : Override the RI modem status signal. This signal will always be
reported as inactive instead of being obtained from the modem status register.
Define this if your serial port does not use this pin.
Example:
uart@80230000 {
compatible = "snps,dw-apb-uart";
reg = <0x80230000 0x100>;
clock-frequency = <3686400>;
interrupts = <10>;
reg-shift = <2>;
reg-io-width = <4>;
dcd-override;
dsr-override;
cts-override;
ri-override;
};
Example with one clock:
uart@80230000 {
compatible = "snps,dw-apb-uart";
reg = <0x80230000 0x100>;
clocks = <&baudclk>;
interrupts = <10>;
reg-shift = <2>;
reg-io-width = <4>;
};
Example with two clocks:
uart@80230000 {
compatible = "snps,dw-apb-uart";
reg = <0x80230000 0x100>;
clocks = <&baudclk>, <&apb_pclk>;
clock-names = "baudclk", "apb_pclk";
interrupts = <10>;
reg-shift = <2>;
reg-io-width = <4>;
};

140
Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml Normal file
View File

@ -0,0 +1,140 @@
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/serial/snps-dw-apb-uart.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Synopsys DesignWare ABP UART
maintainers:
- Rob Herring <robh@kernel.org>
allOf:
- $ref: /schemas/serial.yaml#
properties:
compatible:
oneOf:
- items:
- enum:
- renesas,r9a06g032-uart
- renesas,r9a06g033-uart
- const: renesas,rzn1-uart
- items:
- enum:
- rockchip,px30-uart
- rockchip,rk3036-uart
- rockchip,rk3066-uart
- rockchip,rk3188-uart
- rockchip,rk3288-uart
- rockchip,rk3328-uart
- rockchip,rk3368-uart
- rockchip,rk3399-uart
- rockchip,rv1108-uart
- const: snps,dw-apb-uart
- items:
- enum:
- brcm,bcm11351-dw-apb-uart
- brcm,bcm21664-dw-apb-uart
- const: snps,dw-apb-uart
- const: snps,dw-apb-uart
reg:
maxItems: 1
interrupts:
maxItems: 1
clock-frequency: true
clocks:
minItems: 1
maxItems: 2
clock-names:
items:
- const: baudclk
- const: apb_pclk
snps,uart-16550-compatible:
description: reflects the value of UART_16550_COMPATIBLE configuration
parameter. Define this if your UART does not implement the busy functionality.
type: boolean
resets:
maxItems: 1
reg-shift: true
reg-io-width: true
dcd-override:
description: Override the DCD modem status signal. This signal will
always be reported as active instead of being obtained from the modem
status register. Define this if your serial port does not use this
pin.
type: boolean
dsr-override:
description: Override the DTS modem status signal. This signal will
always be reported as active instead of being obtained from the modem
status register. Define this if your serial port does not use this
pin.
type: boolean
cts-override:
description: Override the CTS modem status signal. This signal will
always be reported as active instead of being obtained from the modem
status register. Define this if your serial port does not use this
pin.
type: boolean
ri-override:
description: Override the RI modem status signal. This signal will always
be reported as inactive instead of being obtained from the modem status
register. Define this if your serial port does not use this pin.
type: boolean
required:
- compatible
- reg
- interrupts
examples:
- |
serial@80230000 {
compatible = "snps,dw-apb-uart";
reg = <0x80230000 0x100>;
clock-frequency = <3686400>;
interrupts = <10>;
reg-shift = <2>;
reg-io-width = <4>;
dcd-override;
dsr-override;
cts-override;
ri-override;
};
- |
// Example with one clock:
serial@80230000 {
compatible = "snps,dw-apb-uart";
reg = <0x80230000 0x100>;
clocks = <&baudclk>;
interrupts = <10>;
reg-shift = <2>;
reg-io-width = <4>;
};
- |
// Example with two clocks:
serial@80230000 {
compatible = "snps,dw-apb-uart";
reg = <0x80230000 0x100>;
clocks = <&baudclk>, <&apb_pclk>;
clock-names = "baudclk", "apb_pclk";
interrupts = <10>;
reg-shift = <2>;
reg-io-width = <4>;
};
...

24
drivers/tty/Kconfig
View File

@ -441,4 +441,28 @@ config VCC
depends on SUN_LDOMS
help
Support for Sun logical domain consoles.
config LDISC_AUTOLOAD
bool "Automatically load TTY Line Disciplines"
default y
help
Historically the kernel has always automatically loaded any
line discipline that is in a kernel module when a user asks
for it to be loaded with the TIOCSETD ioctl, or through other
means. This is not always the best thing to do on systems
where you know you will not be using some of the more
"ancient" line disciplines, so prevent the kernel from doing
this unless the request is coming from a process with the
CAP_SYS_MODULE permissions.
Say 'Y' here if you trust your userspace users to do the right
thing, or if you have only provided the line disciplines that
you know you will be using, or if you wish to continue to use
the traditional method of on-demand loading of these modules
by any user.
This functionality can be changed at runtime with the
dev.tty.ldisc_autoload sysctl, this configuration option will
only set the default value of this functionality.
endif # TTY

2
drivers/tty/hvc/hvc_xen.c
View File

@ -492,7 +492,7 @@ static void xencons_backend_changed(struct xenbus_device *dev,
case XenbusStateClosed:
if (dev->state == XenbusStateClosed)
break;
/* Missed the backend's CLOSING state -- fallthrough */
/* fall through - Missed the backend's CLOSING state. */
case XenbusStateClosing:
xenbus_frontend_closed(dev);
break;

2
drivers/tty/ipwireless/hardware.c
View File

@ -1516,6 +1516,8 @@ static void ipw_send_setup_packet(struct ipw_hardware *hw)
sizeof(struct ipw_setup_get_version_query_packet),
ADDR_SETUP_PROT, TL_PROTOCOLID_SETUP,
TL_SETUP_SIGNO_GET_VERSION_QRY);
if (!ver_packet)
return;
ver_packet->header.length = sizeof(struct tl_setup_get_version_qry);
/*

246
drivers/tty/n_gsm.c
View File

@ -143,8 +143,8 @@ struct gsm_dlci {
struct sk_buff *skb; /* Frame being sent */
struct sk_buff_head skb_list; /* Queued frames */
/* Data handling callback */
void (*data)(struct gsm_dlci *dlci, u8 *data, int len);
void (*prev_data)(struct gsm_dlci *dlci, u8 *data, int len);
void (*data)(struct gsm_dlci *dlci, const u8 *data, int len);
void (*prev_data)(struct gsm_dlci *dlci, const u8 *data, int len);
struct net_device *net; /* network interface, if created */
};
@ -988,7 +988,7 @@ static void gsm_dlci_data_kick(struct gsm_dlci *dlci)
* Encode up and queue a UI/UIH frame containing our response.
*/
static void gsm_control_reply(struct gsm_mux *gsm, int cmd, u8 *data,
static void gsm_control_reply(struct gsm_mux *gsm, int cmd, const u8 *data,
int dlen)
{
struct gsm_msg *msg;
@ -1073,14 +1073,14 @@ static void gsm_process_modem(struct tty_struct *tty, struct gsm_dlci *dlci,
* and if need be stuff a break message down the tty.
*/
static void gsm_control_modem(struct gsm_mux *gsm, u8 *data, int clen)
static void gsm_control_modem(struct gsm_mux *gsm, const u8 *data, int clen)
{
unsigned int addr = 0;
unsigned int modem = 0;
unsigned int brk = 0;
struct gsm_dlci *dlci;
int len = clen;
u8 *dp = data;
const u8 *dp = data;
struct tty_struct *tty;
while (gsm_read_ea(&addr, *dp++) == 0) {
@ -1134,13 +1134,13 @@ static void gsm_control_modem(struct gsm_mux *gsm, u8 *data, int clen)
* this into the uplink tty if present
*/
static void gsm_control_rls(struct gsm_mux *gsm, u8 *data, int clen)
static void gsm_control_rls(struct gsm_mux *gsm, const u8 *data, int clen)
{
struct tty_port *port;
unsigned int addr = 0;
u8 bits;
int len = clen;
u8 *dp = data;
const u8 *dp = data;
while (gsm_read_ea(&addr, *dp++) == 0) {
len--;
@ -1189,7 +1189,7 @@ static void gsm_dlci_begin_close(struct gsm_dlci *dlci);
*/
static void gsm_control_message(struct gsm_mux *gsm, unsigned int command,
u8 *data, int clen)
const u8 *data, int clen)
{
u8 buf[1];
unsigned long flags;
@ -1261,7 +1261,7 @@ static void gsm_control_message(struct gsm_mux *gsm, unsigned int command,
*/
static void gsm_control_response(struct gsm_mux *gsm, unsigned int command,
u8 *data, int clen)
const u8 *data, int clen)
{
struct gsm_control *ctrl;
unsigned long flags;
@ -1553,7 +1553,7 @@ static void gsm_dlci_begin_close(struct gsm_dlci *dlci)
* open we shovel the bits down it, if not we drop them.
*/
static void gsm_dlci_data(struct gsm_dlci *dlci, u8 *data, int clen)
static void gsm_dlci_data(struct gsm_dlci *dlci, const u8 *data, int clen)
{
/* krefs .. */
struct tty_port *port = &dlci->port;
@ -1565,14 +1565,11 @@ static void gsm_dlci_data(struct gsm_dlci *dlci, u8 *data, int clen)
pr_debug("%d bytes for tty\n", len);
switch (dlci->adaption) {
/* Unsupported types */
/* Packetised interruptible data */
case 4:
case 4: /* Packetised interruptible data */
break;
/* Packetised uininterruptible voice/data */
case 3:
case 3: /* Packetised uininterruptible voice/data */
break;
/* Asynchronous serial with line state in each frame */
case 2:
case 2: /* Asynchronous serial with line state in each frame */
while (gsm_read_ea(&modem, *data++) == 0) {
len--;
if (len == 0)
@ -1583,8 +1580,8 @@ static void gsm_dlci_data(struct gsm_dlci *dlci, u8 *data, int clen)
gsm_process_modem(tty, dlci, modem, clen);
tty_kref_put(tty);
}
/* Line state will go via DLCI 0 controls only */
case 1:
/* Fall through */
case 1: /* Line state will go via DLCI 0 controls only */
default:
tty_insert_flip_string(port, data, len);
tty_flip_buffer_push(port);
@ -1603,7 +1600,7 @@ static void gsm_dlci_data(struct gsm_dlci *dlci, u8 *data, int clen)
* and we divide up the work accordingly.
*/
static void gsm_dlci_command(struct gsm_dlci *dlci, u8 *data, int len)
static void gsm_dlci_command(struct gsm_dlci *dlci, const u8 *data, int len)
{
/* See what command is involved */
unsigned int command = 0;
@ -1979,7 +1976,7 @@ static void gsm1_receive(struct gsm_mux *gsm, unsigned char c)
gsm->address = 0;
gsm->state = GSM_ADDRESS;
gsm->fcs = INIT_FCS;
/* Drop through */
/* Fall through */
case GSM_ADDRESS: /* Address continuation */
gsm->fcs = gsm_fcs_add(gsm->fcs, c);
if (gsm_read_ea(&gsm->address, c))
@ -2214,6 +2211,111 @@ static struct gsm_mux *gsm_alloc_mux(void)
return gsm;
}
static void gsm_copy_config_values(struct gsm_mux *gsm,
struct gsm_config *c)
{
memset(c, 0, sizeof(*c));
c->adaption = gsm->adaption;
c->encapsulation = gsm->encoding;
c->initiator = gsm->initiator;
c->t1 = gsm->t1;
c->t2 = gsm->t2;
c->t3 = 0; /* Not supported */
c->n2 = gsm->n2;
if (gsm->ftype == UIH)
c->i = 1;
else
c->i = 2;
pr_debug("Ftype %d i %d\n", gsm->ftype, c->i);
c->mru = gsm->mru;
c->mtu = gsm->mtu;
c->k = 0;
}
static int gsm_config(struct gsm_mux *gsm, struct gsm_config *c)
{
int need_close = 0;
int need_restart = 0;
/* Stuff we don't support yet - UI or I frame transport, windowing */
if ((c->adaption != 1 && c->adaption != 2) || c->k)
return -EOPNOTSUPP;
/* Check the MRU/MTU range looks sane */
if (c->mru > MAX_MRU || c->mtu > MAX_MTU || c->mru < 8 || c->mtu < 8)
return -EINVAL;
if (c->n2 < 3)
return -EINVAL;
if (c->encapsulation > 1) /* Basic, advanced, no I */
return -EINVAL;
if (c->initiator > 1)
return -EINVAL;
if (c->i == 0 || c->i > 2) /* UIH and UI only */
return -EINVAL;
/*
* See what is needed for reconfiguration
*/
/* Timing fields */
if (c->t1 != 0 && c->t1 != gsm->t1)
need_restart = 1;
if (c->t2 != 0 && c->t2 != gsm->t2)
need_restart = 1;
if (c->encapsulation != gsm->encoding)
need_restart = 1;
if (c->adaption != gsm->adaption)
need_restart = 1;
/* Requires care */
if (c->initiator != gsm->initiator)
need_close = 1;
if (c->mru != gsm->mru)
need_restart = 1;
if (c->mtu != gsm->mtu)
need_restart = 1;
/*
* Close down what is needed, restart and initiate the new
* configuration
*/
if (need_close || need_restart) {
int ret;
ret = gsm_disconnect(gsm);
if (ret)
return ret;
}
if (need_restart)
gsm_cleanup_mux(gsm);
gsm->initiator = c->initiator;
gsm->mru = c->mru;
gsm->mtu = c->mtu;
gsm->encoding = c->encapsulation;
gsm->adaption = c->adaption;
gsm->n2 = c->n2;
if (c->i == 1)
gsm->ftype = UIH;
else if (c->i == 2)
gsm->ftype = UI;
if (c->t1)
gsm->t1 = c->t1;
if (c->t2)
gsm->t2 = c->t2;
/*
* FIXME: We need to separate activation/deactivation from adding
* and removing from the mux array
*/
if (need_restart)
gsm_activate_mux(gsm);
if (gsm->initiator && need_close)
gsm_dlci_begin_open(gsm->dlci[0]);
return 0;
}
/**
* gsmld_output - write to link
* @gsm: our mux
@ -2495,89 +2597,6 @@ static __poll_t gsmld_poll(struct tty_struct *tty, struct file *file,
return mask;
}
static int gsmld_config(struct tty_struct *tty, struct gsm_mux *gsm,
struct gsm_config *c)
{
int need_close = 0;
int need_restart = 0;
/* Stuff we don't support yet - UI or I frame transport, windowing */
if ((c->adaption != 1 && c->adaption != 2) || c->k)
return -EOPNOTSUPP;
/* Check the MRU/MTU range looks sane */
if (c->mru > MAX_MRU || c->mtu > MAX_MTU || c->mru < 8 || c->mtu < 8)
return -EINVAL;
if (c->n2 < 3)
return -EINVAL;
if (c->encapsulation > 1) /* Basic, advanced, no I */
return -EINVAL;
if (c->initiator > 1)
return -EINVAL;
if (c->i == 0 || c->i > 2) /* UIH and UI only */
return -EINVAL;
/*
* See what is needed for reconfiguration
*/
/* Timing fields */
if (c->t1 != 0 && c->t1 != gsm->t1)
need_restart = 1;
if (c->t2 != 0 && c->t2 != gsm->t2)
need_restart = 1;
if (c->encapsulation != gsm->encoding)
need_restart = 1;
if (c->adaption != gsm->adaption)
need_restart = 1;
/* Requires care */
if (c->initiator != gsm->initiator)
need_close = 1;
if (c->mru != gsm->mru)
need_restart = 1;
if (c->mtu != gsm->mtu)
need_restart = 1;
/*
* Close down what is needed, restart and initiate the new
* configuration
*/
if (need_close || need_restart) {
int ret;
ret = gsm_disconnect(gsm);
if (ret)
return ret;
}
if (need_restart)
gsm_cleanup_mux(gsm);
gsm->initiator = c->initiator;
gsm->mru = c->mru;
gsm->mtu = c->mtu;
gsm->encoding = c->encapsulation;
gsm->adaption = c->adaption;
gsm->n2 = c->n2;
if (c->i == 1)
gsm->ftype = UIH;
else if (c->i == 2)
gsm->ftype = UI;
if (c->t1)
gsm->t1 = c->t1;
if (c->t2)
gsm->t2 = c->t2;
/* FIXME: We need to separate activation/deactivation from adding
and removing from the mux array */
if (need_restart)
gsm_activate_mux(gsm);
if (gsm->initiator && need_close)
gsm_dlci_begin_open(gsm->dlci[0]);
return 0;
}
static int gsmld_ioctl(struct tty_struct *tty, struct file *file,
unsigned int cmd, unsigned long arg)
{
@ -2586,29 +2605,14 @@ static int gsmld_ioctl(struct tty_struct *tty, struct file *file,
switch (cmd) {
case GSMIOC_GETCONF:
memset(&c, 0, sizeof(c));
c.adaption = gsm->adaption;
c.encapsulation = gsm->encoding;
c.initiator = gsm->initiator;
c.t1 = gsm->t1;
c.t2 = gsm->t2;
c.t3 = 0; /* Not supported */
c.n2 = gsm->n2;
if (gsm->ftype == UIH)
c.i = 1;
else
c.i = 2;
pr_debug("Ftype %d i %d\n", gsm->ftype, c.i);
c.mru = gsm->mru;
c.mtu = gsm->mtu;
c.k = 0;
gsm_copy_config_values(gsm, &c);
if (copy_to_user((void *)arg, &c, sizeof(c)))
return -EFAULT;
return 0;
case GSMIOC_SETCONF:
if (copy_from_user(&c, (void *)arg, sizeof(c)))
return -EFAULT;
return gsmld_config(tty, gsm, &c);
return gsm_config(gsm, &c);
default:
return n_tty_ioctl_helper(tty, file, cmd, arg);
}
@ -2695,7 +2699,7 @@ static void gsm_mux_net_tx_timeout(struct net_device *net)
}
static void gsm_mux_rx_netchar(struct gsm_dlci *dlci,
unsigned char *in_buf, int size)
const unsigned char *in_buf, int size)
{
struct net_device *net = dlci->net;
struct sk_buff *skb;

2
drivers/tty/n_hdlc.c
View File

@ -777,7 +777,7 @@ static int n_hdlc_tty_ioctl(struct tty_struct *tty, struct file *file,
case TCOFLUSH:
flush_tx_queue(tty);
}
/* fall through to default */
/* fall through - to default */
default:
error = n_tty_ioctl_helper(tty, file, cmd, arg);

6
drivers/tty/n_tty.c
View File

@ -50,8 +50,10 @@
#include <linux/ratelimit.h>
#include <linux/vmalloc.h>
/* number of characters left in xmit buffer before select has we have room */
/*
* Until this number of characters is queued in the xmit buffer, select will
* return "we have room for writes".
*/
#define WAKEUP_CHARS 256
/*

10
drivers/tty/nozomi.c
View File

@ -1317,7 +1317,6 @@ static void remove_sysfs_files(struct nozomi *dc)
static int nozomi_card_init(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
resource_size_t start;
int ret;
struct nozomi *dc = NULL;
int ndev_idx;
@ -1357,17 +1356,10 @@ static int nozomi_card_init(struct pci_dev *pdev,
goto err_disable_device;
}
start = pci_resource_start(dc->pdev, 0);
if (start == 0) {
dev_err(&pdev->dev, "No I/O address for card detected\n");
ret = -ENODEV;
goto err_rel_regs;
}
/* Find out what card type it is */
nozomi_get_card_type(dc);
dc->base_addr = ioremap_nocache(start, dc->card_type);
dc->base_addr = pci_iomap(dc->pdev, 0, dc->card_type);
if (!dc->base_addr) {
dev_err(&pdev->dev, "Unable to map card MMIO\n");
ret = -ENODEV;

4
drivers/tty/serdev/serdev-ttyport.c
View File

@ -233,7 +233,7 @@ static int ttyport_get_tiocm(struct serdev_controller *ctrl)
if (!tty->ops->tiocmget)
return -ENOTSUPP;
return tty->driver->ops->tiocmget(tty);
return tty->ops->tiocmget(tty);
}
static int ttyport_set_tiocm(struct serdev_controller *ctrl, unsigned int set, unsigned int clear)
@ -244,7 +244,7 @@ static int ttyport_set_tiocm(struct serdev_controller *ctrl, unsigned int set, u
if (!tty->ops->tiocmset)
return -ENOTSUPP;
return tty->driver->ops->tiocmset(tty, set, clear);
return tty->ops->tiocmset(tty, set, clear);
}
static const struct serdev_controller_ops ctrl_ops = {

13
drivers/tty/serial/8250/8250_ingenic.c
View File

@ -129,22 +129,21 @@ static int __init ingenic_early_console_setup(struct earlycon_device *dev,
return 0;
}
EARLYCON_DECLARE(jz4740_uart, ingenic_early_console_setup);
OF_EARLYCON_DECLARE(jz4740_uart, "ingenic,jz4740-uart",
ingenic_early_console_setup);
EARLYCON_DECLARE(jz4770_uart, ingenic_early_console_setup);
OF_EARLYCON_DECLARE(jz4770_uart, "ingenic,jz4770-uart",
ingenic_early_console_setup);
EARLYCON_DECLARE(jz4775_uart, ingenic_early_console_setup);
OF_EARLYCON_DECLARE(jz4775_uart, "ingenic,jz4775-uart",
ingenic_early_console_setup);
EARLYCON_DECLARE(jz4780_uart, ingenic_early_console_setup);
OF_EARLYCON_DECLARE(jz4780_uart, "ingenic,jz4780-uart",
ingenic_early_console_setup);
OF_EARLYCON_DECLARE(x1000_uart, "ingenic,x1000-uart",
ingenic_early_console_setup);
static void ingenic_uart_serial_out(struct uart_port *p, int offset, int value)
{
int ier;
@ -328,12 +327,18 @@ static const struct ingenic_uart_config jz4780_uart_config = {
.fifosize = 64,
};
static const struct ingenic_uart_config x1000_uart_config = {
.tx_loadsz = 32,
.fifosize = 64,
};
static const struct of_device_id of_match[] = {
{ .compatible = "ingenic,jz4740-uart", .data = &jz4740_uart_config },
{ .compatible = "ingenic,jz4760-uart", .data = &jz4760_uart_config },
{ .compatible = "ingenic,jz4770-uart", .data = &jz4760_uart_config },
{ .compatible = "ingenic,jz4775-uart", .data = &jz4760_uart_config },
{ .compatible = "ingenic,jz4780-uart", .data = &jz4780_uart_config },
{ .compatible = "ingenic,x1000-uart", .data = &x1000_uart_config },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, of_match);

5
drivers/tty/serial/8250/8250_of.c
View File

@ -130,6 +130,10 @@ static int of_platform_serial_setup(struct platform_device *ofdev,
port->flags |= UPF_IOREMAP;
}
/* Compatibility with the deprecated pxa driver and 8250_pxa drivers. */
if (of_device_is_compatible(np, "mrvl,mmp-uart"))
port->regshift = 2;
/* Check for registers offset within the devices address range */
if (of_property_read_u32(np, "reg-shift", &prop) == 0)
port->regshift = prop;
@ -327,6 +331,7 @@ static const struct of_device_id of_platform_serial_table[] = {
{ .compatible = "nvidia,tegra20-uart", .data = (void *)PORT_TEGRA, },
{ .compatible = "nxp,lpc3220-uart", .data = (void *)PORT_LPC3220, },
{ .compatible = "ralink,rt2880-uart", .data = (void *)PORT_RT2880, },
{ .compatible = "intel,xscale-uart", .data = (void *)PORT_XSCALE, },
{ .compatible = "altr,16550-FIFO32",
.data = (void *)PORT_ALTR_16550_F32, },
{ .compatible = "altr,16550-FIFO64",

39
drivers/tty/serial/8250/8250_omap.c
View File

@ -12,6 +12,7 @@
#define SUPPORT_SYSRQ
#endif
#include <linux/clk.h>
#include <linux/device.h>
#include <linux/io.h>
#include <linux/module.h>
@ -1134,10 +1135,12 @@ static int omap8250_probe(struct platform_device *pdev)
{
struct resource *regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
struct device_node *np = pdev->dev.of_node;
struct omap8250_priv *priv;
struct uart_8250_port up;
int ret;
void __iomem *membase;
const struct of_device_id *id;
if (!regs || !irq) {
dev_err(&pdev->dev, "missing registers or irq\n");
@ -1194,26 +1197,30 @@ static int omap8250_probe(struct platform_device *pdev)
up.port.unthrottle = omap_8250_unthrottle;
up.port.rs485_config = omap_8250_rs485_config;
if (pdev->dev.of_node) {
const struct of_device_id *id;
ret = of_alias_get_id(np, "serial");
if (ret < 0) {
dev_err(&pdev->dev, "failed to get alias\n");
return ret;
}
up.port.line = ret;
ret = of_alias_get_id(pdev->dev.of_node, "serial");
if (of_property_read_u32(np, "clock-frequency", &up.port.uartclk)) {
struct clk *clk;
of_property_read_u32(pdev->dev.of_node, "clock-frequency",
&up.port.uartclk);
priv->wakeirq = irq_of_parse_and_map(pdev->dev.of_node, 1);
clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(clk)) {
if (PTR_ERR(clk) == -EPROBE_DEFER)
return -EPROBE_DEFER;
} else {
up.port.uartclk = clk_get_rate(clk);
}
}
priv->wakeirq = irq_of_parse_and_map(np, 1);
id = of_match_device(of_match_ptr(omap8250_dt_ids), &pdev->dev);
if (id && id->data)
priv->habit |= *(u8 *)id->data;
} else {
ret = pdev->id;
}
if (ret < 0) {
dev_err(&pdev->dev, "failed to get alias/pdev id\n");
return ret;
}
up.port.line = ret;
if (!up.port.uartclk) {
up.port.uartclk = DEFAULT_CLK_SPEED;
@ -1242,7 +1249,6 @@ static int omap8250_probe(struct platform_device *pdev)
omap_serial_fill_features_erratas(&up, priv);
up.port.handle_irq = omap8250_no_handle_irq;
#ifdef CONFIG_SERIAL_8250_DMA
if (pdev->dev.of_node) {
/*
* Oh DMA support. If there are no DMA properties in the DT then
* we will fall back to a generic DMA channel which does not
@ -1251,7 +1257,7 @@ static int omap8250_probe(struct platform_device *pdev)
* To avoid "failed to request DMA" messages we check for DMA
* properties in DT.
*/
ret = of_property_count_strings(pdev->dev.of_node, "dma-names");
ret = of_property_count_strings(np, "dma-names");
if (ret == 2) {
up.dma = &priv->omap8250_dma;
priv->omap8250_dma.fn = the_no_dma_filter_fn;
@ -1261,7 +1267,6 @@ static int omap8250_probe(struct platform_device *pdev)
priv->omap8250_dma.rxconf.src_maxburst = RX_TRIGGER;
priv->omap8250_dma.txconf.dst_maxburst = TX_TRIGGER;
}
}
#endif
ret = serial8250_register_8250_port(&up);
if (ret < 0) {

170
drivers/tty/serial/8250/8250_pci.c
View File

@ -2027,6 +2027,111 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.setup = pci_default_setup,
.exit = pci_plx9050_exit,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SDB,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_MPCIE_COM_4S,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4DB,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_MPCIE_COM232_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SMDB,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_MPCIE_COM_4SM,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM422_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM485_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
.device = PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_MPCIE_ICM232_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_PCIE_COM422_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_PCIE_COM485_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SM,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
{
.vendor = PCI_VENDOR_ID_ACCESIO,
.device = PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4SM,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
.setup = pci_pericom_setup,
},
/*
* SBS Technologies, Inc., PMC-OCTALPRO 232
*/
@ -3375,6 +3480,9 @@ static const struct pci_device_id blacklist[] = {
/* Exar devices */
{ PCI_VDEVICE(EXAR, PCI_ANY_ID), },
{ PCI_VDEVICE(COMMTECH, PCI_ANY_ID), },
/* End of the black list */
{ }
};
static int serial_pci_is_class_communication(struct pci_dev *dev)
@ -3392,25 +3500,6 @@ static int serial_pci_is_class_communication(struct pci_dev *dev)
return 0;
}
static int serial_pci_is_blacklisted(struct pci_dev *dev)
{
const struct pci_device_id *bldev;
/*
* Do not access blacklisted devices that are known not to
* feature serial ports or are handled by other modules.
*/
for (bldev = blacklist;
bldev < blacklist + ARRAY_SIZE(blacklist);
bldev++) {
if (dev->vendor == bldev->vendor &&
dev->device == bldev->device)
return -ENODEV;
}
return 0;
}
/*
* Given a complete unknown PCI device, try to use some heuristics to
* guess what the configuration might be, based on the pitiful PCI
@ -3634,6 +3723,7 @@ pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
struct pci_serial_quirk *quirk;
struct serial_private *priv;
const struct pciserial_board *board;
const struct pci_device_id *exclude;
struct pciserial_board tmp;
int rc;
@ -3652,9 +3742,9 @@ pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
board = &pci_boards[ent->driver_data];
rc = serial_pci_is_blacklisted(dev);
if (rc)
return rc;
exclude = pci_match_id(blacklist, dev);
if (exclude)
return -ENODEV;
rc = pcim_enable_device(dev);
pci_save_state(dev);
@ -4575,10 +4665,10 @@ static const struct pci_device_id serial_pci_tbl[] = {
*/
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_2SDB,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_COM_2S,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SDB,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
@ -4587,10 +4677,10 @@ static const struct pci_device_id serial_pci_tbl[] = {
pbn_pericom_PI7C9X7954 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM232_2DB,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_COM232_2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4DB,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
@ -4599,10 +4689,10 @@ static const struct pci_device_id serial_pci_tbl[] = {
pbn_pericom_PI7C9X7954 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_2SMDB,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_COM_2SM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SMDB,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
@ -4611,13 +4701,13 @@ static const struct pci_device_id serial_pci_tbl[] = {
pbn_pericom_PI7C9X7954 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_ICM485_1,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7951 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_ICM422_2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_ICM485_2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_ICM422_4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
@ -4626,16 +4716,16 @@ static const struct pci_device_id serial_pci_tbl[] = {
pbn_pericom_PI7C9X7954 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM_2S,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_MPCIE_ICM232_2,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
@ -4644,13 +4734,13 @@ static const struct pci_device_id serial_pci_tbl[] = {
pbn_pericom_PI7C9X7954 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM_2SM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7954 },
pbn_pericom_PI7C9X7952 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM422_4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7958 },
pbn_pericom_PI7C9X7954 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM485_4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7958 },
pbn_pericom_PI7C9X7954 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM422_8,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7958 },
@ -4659,19 +4749,19 @@ static const struct pci_device_id serial_pci_tbl[] = {
pbn_pericom_PI7C9X7958 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM232_4,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7958 },
pbn_pericom_PI7C9X7954 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM232_8,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7958 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_4SM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7958 },
pbn_pericom_PI7C9X7954 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_COM_8SM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7958 },
{ PCI_VENDOR_ID_ACCESIO, PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4SM,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_pericom_PI7C9X7958 },
pbn_pericom_PI7C9X7954 },
/*
* Topic TP560 Data/Fax/Voice 56k modem (reported by Evan Clarke)
*/

4
drivers/tty/serial/8250/8250_pxa.c
View File

@ -113,6 +113,10 @@ static int serial_pxa_probe(struct platform_device *pdev)
if (ret)
return ret;
ret = of_alias_get_id(pdev->dev.of_node, "serial");
if (ret >= 0)
uart.port.line = ret;
uart.port.type = PORT_XSCALE;
uart.port.iotype = UPIO_MEM32;
uart.port.mapbase = mmres->start;

22
drivers/tty/serial/Kconfig
View File

@ -335,6 +335,28 @@ config SERIAL_TEGRA
are enabled). This driver uses the APB DMA to achieve higher baudrate
and better performance.
config SERIAL_TEGRA_TCU
tristate "NVIDIA Tegra Combined UART"
depends on ARCH_TEGRA && TEGRA_HSP_MBOX
select SERIAL_CORE
help
Support for the mailbox-based TCU (Tegra Combined UART) serial port.
TCU is a virtual serial port that allows multiplexing multiple data
streams into a single hardware serial port.
config SERIAL_TEGRA_TCU_CONSOLE
bool "Support for console on a Tegra TCU serial port"
depends on SERIAL_TEGRA_TCU=y
select SERIAL_CORE_CONSOLE
default y
---help---
If you say Y here, it will be possible to use a the Tegra TCU as the
system console (the system console is the device which receives all
kernel messages and warnings and which allows logins in single user
mode).
If unsure, say Y.
config SERIAL_MAX3100
tristate "MAX3100 support"
depends on SPI

1
drivers/tty/serial/Makefile
View File

@ -77,6 +77,7 @@ obj-$(CONFIG_SERIAL_LANTIQ) += lantiq.o
obj-$(CONFIG_SERIAL_XILINX_PS_UART) += xilinx_uartps.o
obj-$(CONFIG_SERIAL_SIRFSOC) += sirfsoc_uart.o
obj-$(CONFIG_SERIAL_TEGRA) += serial-tegra.o
obj-$(CONFIG_SERIAL_TEGRA_TCU) += tegra-tcu.o
obj-$(CONFIG_SERIAL_AR933X) += ar933x_uart.o
obj-$(CONFIG_SERIAL_EFM32_UART) += efm32-uart.o
obj-$(CONFIG_SERIAL_ARC) += arc_uart.o

17
drivers/tty/serial/clps711x.c
View File

@ -442,14 +442,10 @@ static struct console clps711x_console = {
static int uart_clps711x_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
int ret, index = np ? of_alias_get_id(np, "serial") : pdev->id;
struct clps711x_port *s;
struct resource *res;
struct clk *uart_clk;
int irq;
if (index < 0 || index >= UART_CLPS711X_NR)
return -EINVAL;
int irq, ret;
s = devm_kzalloc(&pdev->dev, sizeof(*s), GFP_KERNEL);
if (!s)
@ -473,20 +469,11 @@ static int uart_clps711x_probe(struct platform_device *pdev)
if (s->rx_irq < 0)
return s->rx_irq;
if (!np) {
char syscon_name[9];
sprintf(syscon_name, "syscon.%i", index + 1);
s->syscon = syscon_regmap_lookup_by_pdevname(syscon_name);
if (IS_ERR(s->syscon))
return PTR_ERR(s->syscon);
} else {
s->syscon = syscon_regmap_lookup_by_phandle(np, "syscon");
if (IS_ERR(s->syscon))
return PTR_ERR(s->syscon);
}
s->port.line = index;
s->port.line = of_alias_get_id(np, "serial");
s->port.dev = &pdev->dev;
s->port.iotype = UPIO_MEM32;
s->port.mapbase = res->start;

178
drivers/tty/serial/fsl_lpuart.c
View File

@ -426,6 +426,17 @@ static void lpuart_dma_tx_complete(void *arg)
spin_unlock_irqrestore(&sport->port.lock, flags);
}
static dma_addr_t lpuart_dma_datareg_addr(struct lpuart_port *sport)
{
switch (sport->port.iotype) {
case UPIO_MEM32:
return sport->port.mapbase + UARTDATA;
case UPIO_MEM32BE:
return sport->port.mapbase + UARTDATA + sizeof(u32) - 1;
}
return sport->port.mapbase + UARTDR;
}
static int lpuart_dma_tx_request(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port,
@ -433,7 +444,7 @@ static int lpuart_dma_tx_request(struct uart_port *port)
struct dma_slave_config dma_tx_sconfig = {};
int ret;
dma_tx_sconfig.dst_addr = sport->port.mapbase + UARTDR;
dma_tx_sconfig.dst_addr = lpuart_dma_datareg_addr(sport);
dma_tx_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
dma_tx_sconfig.dst_maxburst = 1;
dma_tx_sconfig.direction = DMA_MEM_TO_DEV;
@ -636,14 +647,20 @@ static void lpuart_start_tx(struct uart_port *port)
static void lpuart32_start_tx(struct uart_port *port)
{
struct lpuart_port *sport = container_of(port, struct lpuart_port, port);
struct circ_buf *xmit = &sport->port.state->xmit;
unsigned long temp;
if (sport->lpuart_dma_tx_use) {
if (!uart_circ_empty(xmit) && !uart_tx_stopped(port))
lpuart_dma_tx(sport);
} else {
temp = lpuart32_read(port, UARTCTRL);
lpuart32_write(port, temp | UARTCTRL_TIE, UARTCTRL);
if (lpuart32_read(port, UARTSTAT) & UARTSTAT_TDRE)
lpuart32_transmit_buffer(sport);
}
}
/* return TIOCSER_TEMT when transmitter is not busy */
static unsigned int lpuart_tx_empty(struct uart_port *port)
@ -664,8 +681,18 @@ static unsigned int lpuart_tx_empty(struct uart_port *port)
static unsigned int lpuart32_tx_empty(struct uart_port *port)
{
return (lpuart32_read(port, UARTSTAT) & UARTSTAT_TC) ?
TIOCSER_TEMT : 0;
struct lpuart_port *sport = container_of(port,
struct lpuart_port, port);
unsigned long stat = lpuart32_read(port, UARTSTAT);
unsigned long sfifo = lpuart32_read(port, UARTFIFO);
if (sport->dma_tx_in_progress)
return 0;
if (stat & UARTSTAT_TC && sfifo & UARTFIFO_TXEMPT)
return TIOCSER_TEMT;
return 0;
}
static bool lpuart_is_32(struct lpuart_port *sport)
@ -862,11 +889,10 @@ static irqreturn_t lpuart32_int(int irq, void *dev_id)
rxcount = lpuart32_read(&sport->port, UARTWATER);
rxcount = rxcount >> UARTWATER_RXCNT_OFF;
if (sts & UARTSTAT_RDRF || rxcount > 0)
if ((sts & UARTSTAT_RDRF || rxcount > 0) && !sport->lpuart_dma_rx_use)
lpuart32_rxint(irq, dev_id);
if ((sts & UARTSTAT_TDRE) &&
!(lpuart32_read(&sport->port, UARTBAUD) & UARTBAUD_TDMAE))
if ((sts & UARTSTAT_TDRE) && !sport->lpuart_dma_tx_use)
lpuart_txint(irq, dev_id);
lpuart32_write(&sport->port, sts, UARTSTAT);
@ -881,9 +907,21 @@ static void lpuart_copy_rx_to_tty(struct lpuart_port *sport)
struct circ_buf *ring = &sport->rx_ring;
unsigned long flags;
int count = 0;
unsigned char sr;
sr = readb(sport->port.membase + UARTSR1);
if (lpuart_is_32(sport)) {
unsigned long sr = lpuart32_read(&sport->port, UARTSTAT);
if (sr & (UARTSTAT_PE | UARTSTAT_FE)) {
/* Read DR to clear the error flags */
lpuart32_read(&sport->port, UARTDATA);
if (sr & UARTSTAT_PE)
sport->port.icount.parity++;
else if (sr & UARTSTAT_FE)
sport->port.icount.frame++;
}
} else {
unsigned char sr = readb(sport->port.membase + UARTSR1);
if (sr & (UARTSR1_PE | UARTSR1_FE)) {
/* Read DR to clear the error flags */
@ -894,6 +932,7 @@ static void lpuart_copy_rx_to_tty(struct lpuart_port *sport)
else if (sr & UARTSR1_FE)
sport->port.icount.frame++;
}
}
async_tx_ack(sport->dma_rx_desc);
@ -1015,7 +1054,7 @@ static inline int lpuart_start_rx_dma(struct lpuart_port *sport)
return -EINVAL;
}
dma_rx_sconfig.src_addr = sport->port.mapbase + UARTDR;
dma_rx_sconfig.src_addr = lpuart_dma_datareg_addr(sport);
dma_rx_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
dma_rx_sconfig.src_maxburst = 1;
dma_rx_sconfig.direction = DMA_DEV_TO_MEM;
@ -1043,8 +1082,14 @@ static inline int lpuart_start_rx_dma(struct lpuart_port *sport)
sport->dma_rx_cookie = dmaengine_submit(sport->dma_rx_desc);
dma_async_issue_pending(sport->dma_rx_chan);
if (lpuart_is_32(sport)) {
unsigned long temp = lpuart32_read(&sport->port, UARTBAUD);
lpuart32_write(&sport->port, temp | UARTBAUD_RDMAE, UARTBAUD);
} else {
writeb(readb(sport->port.membase + UARTCR5) | UARTCR5_RDMAS,
sport->port.membase + UARTCR5);
}
return 0;
}
@ -1334,6 +1379,8 @@ static int lpuart32_startup(struct uart_port *port)
sport->txfifo_size = 0x1 << (((temp >> UARTFIFO_TXSIZE_OFF) &
UARTFIFO_FIFOSIZE_MASK) - 1);
sport->port.fifosize = sport->txfifo_size;
sport->rxfifo_size = 0x1 << (((temp >> UARTFIFO_RXSIZE_OFF) &
UARTFIFO_FIFOSIZE_MASK) - 1);
@ -1342,8 +1389,41 @@ static int lpuart32_startup(struct uart_port *port)
lpuart32_setup_watermark(sport);
temp = lpuart32_read(&sport->port, UARTCTRL);
temp |= (UARTCTRL_RIE | UARTCTRL_TIE | UARTCTRL_RE | UARTCTRL_TE);
temp |= UARTCTRL_ILIE;
temp |= UARTCTRL_RE | UARTCTRL_TE | UARTCTRL_ILIE;
lpuart32_write(&sport->port, temp, UARTCTRL);
if (sport->dma_rx_chan && !lpuart_start_rx_dma(sport)) {
/* set Rx DMA timeout */
sport->dma_rx_timeout = msecs_to_jiffies(DMA_RX_TIMEOUT);
if (!sport->dma_rx_timeout)
sport->dma_rx_timeout = 1;
sport->lpuart_dma_rx_use = true;
rx_dma_timer_init(sport);
} else {
sport->lpuart_dma_rx_use = false;
}
if (sport->dma_tx_chan && !lpuart_dma_tx_request(port)) {
init_waitqueue_head(&sport->dma_wait);
sport->lpuart_dma_tx_use = true;
temp = lpuart32_read(&sport->port, UARTBAUD);
lpuart32_write(&sport->port, temp | UARTBAUD_TDMAE, UARTBAUD);
} else {
sport->lpuart_dma_tx_use = false;
}
if (sport->lpuart_dma_rx_use) {
/* RXWATER must be 0 */
temp = lpuart32_read(&sport->port, UARTWATER);
temp &= ~(UARTWATER_WATER_MASK << UARTWATER_RXWATER_OFF);
lpuart32_write(&sport->port, temp, UARTWATER);
}
temp = lpuart32_read(&sport->port, UARTCTRL);
if (!sport->lpuart_dma_rx_use)
temp |= UARTCTRL_RIE;
if (!sport->lpuart_dma_tx_use)
temp |= UARTCTRL_TIE;
lpuart32_write(&sport->port, temp, UARTCTRL);
spin_unlock_irqrestore(&sport->port.lock, flags);
@ -1384,6 +1464,8 @@ static void lpuart_shutdown(struct uart_port *port)
static void lpuart32_shutdown(struct uart_port *port)
{
struct lpuart_port *sport =
container_of(port, struct lpuart_port, port);
unsigned long temp;
unsigned long flags;
@ -1396,6 +1478,21 @@ static void lpuart32_shutdown(struct uart_port *port)
lpuart32_write(port, temp, UARTCTRL);
spin_unlock_irqrestore(&port->lock, flags);
if (sport->lpuart_dma_rx_use) {
del_timer_sync(&sport->lpuart_timer);
lpuart_dma_rx_free(&sport->port);
}
if (sport->lpuart_dma_tx_use) {
if (wait_event_interruptible(sport->dma_wait,
!sport->dma_tx_in_progress)) {
sport->dma_tx_in_progress = false;
dmaengine_terminate_all(sport->dma_tx_chan);
}
lpuart32_stop_tx(port);
}
}
static void
@ -1621,7 +1718,10 @@ lpuart32_serial_setbrg(struct lpuart_port *sport, unsigned int baudrate)
tmp &= ~UARTBAUD_SBR_MASK;
tmp |= sbr & UARTBAUD_SBR_MASK;
tmp &= ~(UARTBAUD_TDMAE | UARTBAUD_RDMAE);
if (!sport->lpuart_dma_rx_use)
tmp &= ~UARTBAUD_RDMAE;
if (!sport->lpuart_dma_tx_use)
tmp &= ~UARTBAUD_TDMAE;
lpuart32_write(&sport->port, tmp, UARTBAUD);
}
@ -1699,6 +1799,18 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
/* ask the core to calculate the divisor */
baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 4);
/*
* Need to update the Ring buffer length according to the selected
* baud rate and restart Rx DMA path.
*
* Since timer function acqures sport->port.lock, need to stop before
* acquring same lock because otherwise del_timer_sync() can deadlock.
*/
if (old && sport->lpuart_dma_rx_use) {
del_timer_sync(&sport->lpuart_timer);
lpuart_dma_rx_free(&sport->port);
}
spin_lock_irqsave(&sport->port.lock, flags);
sport->port.read_status_mask = 0;
@ -1737,6 +1849,13 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
lpuart32_write(&sport->port, ctrl, UARTCTRL);
/* restore control register */
if (old && sport->lpuart_dma_rx_use) {
if (!lpuart_start_rx_dma(sport))
rx_dma_timer_init(sport);
else
sport->lpuart_dma_rx_use = false;
}
spin_unlock_irqrestore(&sport->port.lock, flags);
}
@ -2306,8 +2425,14 @@ static int lpuart_suspend(struct device *dev)
}
/* Disable Rx DMA to use UART port as wakeup source */
writeb(readb(sport->port.membase + UARTCR5) & ~UARTCR5_RDMAS,
sport->port.membase + UARTCR5);
if (lpuart_is_32(sport)) {
temp = lpuart32_read(&sport->port, UARTBAUD);
lpuart32_write(&sport->port, temp & ~UARTBAUD_RDMAE,
UARTBAUD);
} else {
writeb(readb(sport->port.membase + UARTCR5) &
~UARTCR5_RDMAS, sport->port.membase + UARTCR5);
}
}
if (sport->lpuart_dma_tx_use) {
@ -2333,8 +2458,7 @@ static int lpuart_resume(struct device *dev)
if (lpuart_is_32(sport)) {
lpuart32_setup_watermark(sport);
temp = lpuart32_read(&sport->port, UARTCTRL);
temp |= (UARTCTRL_RIE | UARTCTRL_TIE | UARTCTRL_RE |
UARTCTRL_TE | UARTCTRL_ILIE);
temp |= UARTCTRL_RE | UARTCTRL_TE | UARTCTRL_ILIE;
lpuart32_write(&sport->port, temp, UARTCTRL);
} else {
lpuart_setup_watermark(sport);
@ -2355,12 +2479,34 @@ static int lpuart_resume(struct device *dev)
if (sport->dma_tx_chan && !lpuart_dma_tx_request(&sport->port)) {
init_waitqueue_head(&sport->dma_wait);
sport->lpuart_dma_tx_use = true;
if (lpuart_is_32(sport)) {
temp = lpuart32_read(&sport->port, UARTBAUD);
lpuart32_write(&sport->port,
temp | UARTBAUD_TDMAE, UARTBAUD);
} else {
writeb(readb(sport->port.membase + UARTCR5) |
UARTCR5_TDMAS, sport->port.membase + UARTCR5);
}
} else {
sport->lpuart_dma_tx_use = false;
}
if (lpuart_is_32(sport)) {
if (sport->lpuart_dma_rx_use) {
/* RXWATER must be 0 */
temp = lpuart32_read(&sport->port, UARTWATER);
temp &= ~(UARTWATER_WATER_MASK <<
UARTWATER_RXWATER_OFF);
lpuart32_write(&sport->port, temp, UARTWATER);
}
temp = lpuart32_read(&sport->port, UARTCTRL);
if (!sport->lpuart_dma_rx_use)
temp |= UARTCTRL_RIE;
if (!sport->lpuart_dma_tx_use)
temp |= UARTCTRL_TIE;
lpuart32_write(&sport->port, temp, UARTCTRL);
}
uart_resume_port(&lpuart_reg, &sport->port);
return 0;

4
drivers/tty/serial/lpc32xx_hs.c
View File

@ -151,6 +151,8 @@ static void lpc32xx_hsuart_console_write(struct console *co, const char *s,
local_irq_restore(flags);
}
static void lpc32xx_loopback_set(resource_size_t mapbase, int state);
static int __init lpc32xx_hsuart_console_setup(struct console *co,
char *options)
{
@ -170,6 +172,8 @@ static int __init lpc32xx_hsuart_console_setup(struct console *co,
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
lpc32xx_loopback_set(port->mapbase, 0); /* get out of loopback mode */
return uart_set_options(port, co, baud, parity, bits, flow);
}

21
drivers/tty/serial/max310x.c
View File

@ -248,6 +248,7 @@
struct max310x_devtype {
char name[9];
int nr;
u8 mode1;
int (*detect)(struct device *);
void (*power)(struct uart_port *, int);
};
@ -410,6 +411,7 @@ static void max14830_power(struct uart_port *port, int on)
static const struct max310x_devtype max3107_devtype = {
.name = "MAX3107",
.nr = 1,
.mode1 = MAX310X_MODE1_AUTOSLEEP_BIT | MAX310X_MODE1_IRQSEL_BIT,
.detect = max3107_detect,
.power = max310x_power,
};
@ -417,6 +419,7 @@ static const struct max310x_devtype max3107_devtype = {
static const struct max310x_devtype max3108_devtype = {
.name = "MAX3108",
.nr = 1,
.mode1 = MAX310X_MODE1_AUTOSLEEP_BIT,
.detect = max3108_detect,
.power = max310x_power,
};
@ -424,6 +427,7 @@ static const struct max310x_devtype max3108_devtype = {
static const struct max310x_devtype max3109_devtype = {
.name = "MAX3109",
.nr = 2,
.mode1 = MAX310X_MODE1_AUTOSLEEP_BIT,
.detect = max3109_detect,
.power = max310x_power,
};
@ -431,6 +435,7 @@ static const struct max310x_devtype max3109_devtype = {
static const struct max310x_devtype max14830_devtype = {
.name = "MAX14830",
.nr = 4,
.mode1 = MAX310X_MODE1_IRQSEL_BIT,
.detect = max14830_detect,
.power = max14830_power,
};
@ -1197,8 +1202,7 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype,
return PTR_ERR(regmap);
/* Alloc port structure */
s = devm_kzalloc(dev, sizeof(*s) +
sizeof(struct max310x_one) * devtype->nr, GFP_KERNEL);
s = devm_kzalloc(dev, struct_size(s, p, devtype->nr), GFP_KERNEL);
if (!s) {
dev_err(dev, "Error allocating port structure\n");
return -ENOMEM;
@ -1258,9 +1262,8 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype,
MAX310X_BRGDIVLSB_REG + offs, &ret);
} while (ret != 0x01);
regmap_update_bits(s->regmap, MAX310X_MODE1_REG + offs,
MAX310X_MODE1_AUTOSLEEP_BIT,
MAX310X_MODE1_AUTOSLEEP_BIT);
regmap_write(s->regmap, MAX310X_MODE1_REG + offs,
devtype->mode1);
}
uartclk = max310x_set_ref_clk(dev, s, freq, xtal);
@ -1294,10 +1297,6 @@ static int max310x_probe(struct device *dev, struct max310x_devtype *devtype,
max310x_port_write(&s->p[i].port, MAX310X_IRQEN_REG, 0);
/* Clear IRQ status register */
max310x_port_read(&s->p[i].port, MAX310X_IRQSTS_REG);
/* Enable IRQ pin */
max310x_port_update(&s->p[i].port, MAX310X_MODE1_REG,
MAX310X_MODE1_IRQSEL_BIT,
MAX310X_MODE1_IRQSEL_BIT);
/* Initialize queue for start TX */
INIT_WORK(&s->p[i].tx_work, max310x_wq_proc);
/* Initialize queue for changing LOOPBACK mode */
@ -1467,10 +1466,10 @@ static int __init max310x_uart_init(void)
return ret;
#ifdef CONFIG_SPI_MASTER
spi_register_driver(&max310x_spi_driver);
ret = spi_register_driver(&max310x_spi_driver);
#endif
return 0;
return ret;
}
module_init(max310x_uart_init);

13
drivers/tty/serial/meson_uart.c
View File

@ -72,7 +72,8 @@
#define AML_UART_BAUD_USE BIT(23)
#define AML_UART_BAUD_XTAL BIT(24)
#define AML_UART_PORT_NUM 6
#define AML_UART_PORT_NUM 12
#define AML_UART_PORT_OFFSET 6
#define AML_UART_DEV_NAME "ttyAML"
@ -654,10 +655,20 @@ static int meson_uart_probe(struct platform_device *pdev)
struct resource *res_mem, *res_irq;
struct uart_port *port;
int ret = 0;
int id = -1;
if (pdev->dev.of_node)
pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
if (pdev->id < 0) {
for (id = AML_UART_PORT_OFFSET; id < AML_UART_PORT_NUM; id++) {
if (!meson_ports[id]) {
pdev->id = id;
break;
}
}
}
if (pdev->id < 0 || pdev->id >= AML_UART_PORT_NUM)
return -EINVAL;

114
drivers/tty/serial/mps2-uart.c
View File

@ -22,6 +22,7 @@
#include <linux/serial_core.h>
#include <linux/tty_flip.h>
#include <linux/types.h>
#include <linux/idr.h>
#define SERIAL_NAME "ttyMPS"
#define DRIVER_NAME "mps2-uart"
@ -65,11 +66,14 @@
#define MPS2_MAX_PORTS 3
#define UART_PORT_COMBINED_IRQ BIT(0)
struct mps2_uart_port {
struct uart_port port;
struct clk *clk;
unsigned int tx_irq;
unsigned int rx_irq;
unsigned int flags;
};
static inline struct mps2_uart_port *to_mps2_port(struct uart_port *port)
@ -264,6 +268,20 @@ static irqreturn_t mps2_uart_oerrirq(int irq, void *data)
return handled;
}
static irqreturn_t mps2_uart_combinedirq(int irq, void *data)
{
if (mps2_uart_rxirq(irq, data) == IRQ_HANDLED)
return IRQ_HANDLED;
if (mps2_uart_txirq(irq, data) == IRQ_HANDLED)
return IRQ_HANDLED;
if (mps2_uart_oerrirq(irq, data) == IRQ_HANDLED)
return IRQ_HANDLED;
return IRQ_NONE;
}
static int mps2_uart_startup(struct uart_port *port)
{
struct mps2_uart_port *mps_port = to_mps2_port(port);
@ -274,11 +292,28 @@ static int mps2_uart_startup(struct uart_port *port)
mps2_uart_write8(port, control, UARTn_CTRL);
if (mps_port->flags & UART_PORT_COMBINED_IRQ) {
ret = request_irq(port->irq, mps2_uart_combinedirq, 0,
MAKE_NAME(-combined), mps_port);
if (ret) {
dev_err(port->dev, "failed to register combinedirq (%d)\n", ret);
return ret;
}
} else {
ret = request_irq(port->irq, mps2_uart_oerrirq, IRQF_SHARED,
MAKE_NAME(-overrun), mps_port);
if (ret) {
dev_err(port->dev, "failed to register oerrirq (%d)\n", ret);
return ret;
}
ret = request_irq(mps_port->rx_irq, mps2_uart_rxirq, 0,
MAKE_NAME(-rx), mps_port);
if (ret) {
dev_err(port->dev, "failed to register rxirq (%d)\n", ret);
return ret;
goto err_free_oerrirq;
}
ret = request_irq(mps_port->tx_irq, mps2_uart_txirq, 0,
@ -288,12 +323,6 @@ static int mps2_uart_startup(struct uart_port *port)
goto err_free_rxirq;
}
ret = request_irq(port->irq, mps2_uart_oerrirq, IRQF_SHARED,
MAKE_NAME(-overrun), mps_port);
if (ret) {
dev_err(port->dev, "failed to register oerrirq (%d)\n", ret);
goto err_free_txirq;
}
control |= UARTn_CTRL_RX_GRP | UARTn_CTRL_TX_GRP;
@ -302,10 +331,10 @@ static int mps2_uart_startup(struct uart_port *port)
return 0;
err_free_txirq:
free_irq(mps_port->tx_irq, mps_port);
err_free_rxirq:
free_irq(mps_port->rx_irq, mps_port);
err_free_oerrirq:
free_irq(port->irq, mps_port);
return ret;
}
@ -319,8 +348,11 @@ static void mps2_uart_shutdown(struct uart_port *port)
mps2_uart_write8(port, control, UARTn_CTRL);
if (!(mps_port->flags & UART_PORT_COMBINED_IRQ)) {
free_irq(mps_port->rx_irq, mps_port);
free_irq(mps_port->tx_irq, mps_port);
}
free_irq(port->irq, mps_port);
}
@ -397,7 +429,7 @@ static const struct uart_ops mps2_uart_pops = {
.verify_port = mps2_uart_verify_port,
};
static struct mps2_uart_port mps2_uart_ports[MPS2_MAX_PORTS];
static DEFINE_IDR(ports_idr);
#ifdef CONFIG_SERIAL_MPS2_UART_CONSOLE
static void mps2_uart_console_putchar(struct uart_port *port, int ch)
@ -410,7 +442,8 @@ static void mps2_uart_console_putchar(struct uart_port *port, int ch)
static void mps2_uart_console_write(struct console *co, const char *s, unsigned int cnt)
{
struct uart_port *port = &mps2_uart_ports[co->index].port;
struct mps2_uart_port *mps_port = idr_find(&ports_idr, co->index);
struct uart_port *port = &mps_port->port;
uart_console_write(port, s, cnt, mps2_uart_console_putchar);
}
@ -426,7 +459,10 @@ static int mps2_uart_console_setup(struct console *co, char *options)
if (co->index < 0 || co->index >= MPS2_MAX_PORTS)
return -ENODEV;
mps_port = &mps2_uart_ports[co->index];
mps_port = idr_find(&ports_idr, co->index);
if (!mps_port)
return -ENODEV;
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
@ -487,27 +523,36 @@ static struct uart_driver mps2_uart_driver = {
.cons = MPS2_SERIAL_CONSOLE,
};
static struct mps2_uart_port *mps2_of_get_port(struct platform_device *pdev)
static int mps2_of_get_port(struct platform_device *pdev,
struct mps2_uart_port *mps_port)
{
struct device_node *np = pdev->dev.of_node;
int id;
if (!np)
return NULL;
return -ENODEV;
id = of_alias_get_id(np, "serial");
if (id < 0)
id = 0;
id = idr_alloc_cyclic(&ports_idr, (void *)mps_port, 0, MPS2_MAX_PORTS, GFP_KERNEL);
else
id = idr_alloc(&ports_idr, (void *)mps_port, id, MPS2_MAX_PORTS, GFP_KERNEL);
if (WARN_ON(id >= MPS2_MAX_PORTS))
return NULL;
if (id < 0)
return id;
mps2_uart_ports[id].port.line = id;
return &mps2_uart_ports[id];
/* Only combined irq is presesnt */
if (platform_irq_count(pdev) == 1)
mps_port->flags |= UART_PORT_COMBINED_IRQ;
mps_port->port.line = id;
return 0;
}
static int mps2_init_port(struct mps2_uart_port *mps_port,
struct platform_device *pdev)
static int mps2_init_port(struct platform_device *pdev,
struct mps2_uart_port *mps_port)
{
struct resource *res;
int ret;
@ -519,11 +564,6 @@ static int mps2_init_port(struct mps2_uart_port *mps_port,
mps_port->port.mapbase = res->start;
mps_port->port.mapsize = resource_size(res);
mps_port->rx_irq = platform_get_irq(pdev, 0);
mps_port->tx_irq = platform_get_irq(pdev, 1);
mps_port->port.irq = platform_get_irq(pdev, 2);
mps_port->port.iotype = UPIO_MEM;
mps_port->port.flags = UPF_BOOT_AUTOCONF;
mps_port->port.fifosize = 1;
@ -542,6 +582,15 @@ static int mps2_init_port(struct mps2_uart_port *mps_port,
clk_disable_unprepare(mps_port->clk);
if (mps_port->flags & UART_PORT_COMBINED_IRQ) {
mps_port->port.irq = platform_get_irq(pdev, 0);
} else {
mps_port->rx_irq = platform_get_irq(pdev, 0);
mps_port->tx_irq = platform_get_irq(pdev, 1);
mps_port->port.irq = platform_get_irq(pdev, 2);
}
return ret;
}
@ -550,11 +599,16 @@ static int mps2_serial_probe(struct platform_device *pdev)
struct mps2_uart_port *mps_port;
int ret;
mps_port = mps2_of_get_port(pdev);
if (!mps_port)
return -ENODEV;
mps_port = devm_kzalloc(&pdev->dev, sizeof(struct mps2_uart_port), GFP_KERNEL);
ret = mps2_init_port(mps_port, pdev);
if (!mps_port)
return -ENOMEM;
ret = mps2_of_get_port(pdev, mps_port);
if (ret)
return ret;
ret = mps2_init_port(pdev, mps_port);
if (ret)
return ret;

2
drivers/tty/serial/msm_serial.c
View File

@ -1634,7 +1634,7 @@ static void msm_console_write(struct console *co, const char *s,
__msm_console_write(port, s, count, msm_port->is_uartdm);
}
static int __init msm_console_setup(struct console *co, char *options)
static int msm_console_setup(struct console *co, char *options)
{
struct uart_port *port;
int baud = 115200;

259
drivers/tty/serial/qcom_geni_serial.c
View File

@ -89,7 +89,7 @@
#define DEF_FIFO_DEPTH_WORDS 16
#define DEF_TX_WM 2
#define DEF_FIFO_WIDTH_BITS 32
#define UART_CONSOLE_RX_WM 2
#define UART_RX_WM 2
#define MAX_LOOPBACK_CFG 3
#ifdef CONFIG_CONSOLE_POLL
@ -105,10 +105,6 @@ struct qcom_geni_serial_port {
u32 tx_fifo_depth;
u32 tx_fifo_width;
u32 rx_fifo_depth;
u32 tx_wm;
u32 rx_wm;
u32 rx_rfr;
enum geni_se_xfer_mode xfer_mode;
bool setup;
int (*handle_rx)(struct uart_port *uport, u32 bytes, bool drop);
unsigned int baud;
@ -228,7 +224,7 @@ static unsigned int qcom_geni_serial_get_mctrl(struct uart_port *uport)
if (uart_console(uport)) {
mctrl |= TIOCM_CTS;
} else {
geni_ios = readl_relaxed(uport->membase + SE_GENI_IOS);
geni_ios = readl(uport->membase + SE_GENI_IOS);
if (!(geni_ios & IO2_DATA_IN))
mctrl |= TIOCM_CTS;
}
@ -246,7 +242,7 @@ static void qcom_geni_serial_set_mctrl(struct uart_port *uport,
if (!(mctrl & TIOCM_RTS))
uart_manual_rfr = UART_MANUAL_RFR_EN | UART_RFR_NOT_READY;
writel_relaxed(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR);
writel(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR);
}
static const char *qcom_geni_serial_get_type(struct uart_port *uport)
@ -275,9 +271,6 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
unsigned int fifo_bits;
unsigned long timeout_us = 20000;
/* Ensure polling is not re-ordered before the prior writes/reads */
mb();
if (uport->private_data) {
port = to_dev_port(uport, uport);
baud = port->baud;
@ -297,7 +290,7 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
*/
timeout_us = DIV_ROUND_UP(timeout_us, 10) * 10;
while (timeout_us) {
reg = readl_relaxed(uport->membase + offset);
reg = readl(uport->membase + offset);
if ((bool)(reg & field) == set)
return true;
udelay(10);
@ -310,7 +303,7 @@ static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size)
{
u32 m_cmd;
writel_relaxed(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN);
writel(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN);
m_cmd = UART_START_TX << M_OPCODE_SHFT;
writel(m_cmd, uport->membase + SE_GENI_M_CMD0);
}
@ -323,13 +316,13 @@ static void qcom_geni_serial_poll_tx_done(struct uart_port *uport)
done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_DONE_EN, true);
if (!done) {
writel_relaxed(M_GENI_CMD_ABORT, uport->membase +
writel(M_GENI_CMD_ABORT, uport->membase +
SE_GENI_M_CMD_CTRL_REG);
irq_clear |= M_CMD_ABORT_EN;
qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_ABORT_EN, true);
}
writel_relaxed(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR);
writel(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR);
}
static void qcom_geni_serial_abort_rx(struct uart_port *uport)
@ -339,8 +332,8 @@ static void qcom_geni_serial_abort_rx(struct uart_port *uport)
writel(S_GENI_CMD_ABORT, uport->membase + SE_GENI_S_CMD_CTRL_REG);
qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG,
S_GENI_CMD_ABORT, false);
writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
writel_relaxed(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG);
writel(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
writel(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG);
}
#ifdef CONFIG_CONSOLE_POLL
@ -349,19 +342,13 @@ static int qcom_geni_serial_get_char(struct uart_port *uport)
u32 rx_fifo;
u32 status;
status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS);
writel_relaxed(status, uport->membase + SE_GENI_M_IRQ_CLEAR);
status = readl(uport->membase + SE_GENI_M_IRQ_STATUS);
writel(status, uport->membase + SE_GENI_M_IRQ_CLEAR);
status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS);
writel_relaxed(status, uport->membase + SE_GENI_S_IRQ_CLEAR);
status = readl(uport->membase + SE_GENI_S_IRQ_STATUS);
writel(status, uport->membase + SE_GENI_S_IRQ_CLEAR);
/*
* Ensure the writes to clear interrupts is not re-ordered after
* reading the data.
*/
mb();
status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS);
status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS);
if (!(status & RX_FIFO_WC_MSK))
return NO_POLL_CHAR;
@ -372,15 +359,12 @@ static int qcom_geni_serial_get_char(struct uart_port *uport)
static void qcom_geni_serial_poll_put_char(struct uart_port *uport,
unsigned char c)
{
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
writel_relaxed(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG);
writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
qcom_geni_serial_setup_tx(uport, 1);
WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_TX_FIFO_WATERMARK_EN, true));
writel_relaxed(c, uport->membase + SE_GENI_TX_FIFOn);
writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
writel(c, uport->membase + SE_GENI_TX_FIFOn);
writel(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
qcom_geni_serial_poll_tx_done(uport);
}
#endif
@ -388,7 +372,7 @@ static void qcom_geni_serial_poll_put_char(struct uart_port *uport,
#ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE
static void qcom_geni_serial_wr_char(struct uart_port *uport, int ch)
{
writel_relaxed(ch, uport->membase + SE_GENI_TX_FIFOn);
writel(ch, uport->membase + SE_GENI_TX_FIFOn);
}
static void
@ -407,7 +391,7 @@ __qcom_geni_serial_console_write(struct uart_port *uport, const char *s,
bytes_to_send++;
}
writel_relaxed(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
qcom_geni_serial_setup_tx(uport, bytes_to_send);
for (i = 0; i < count; ) {
size_t chars_to_write = 0;
@ -425,7 +409,7 @@ __qcom_geni_serial_console_write(struct uart_port *uport, const char *s,
chars_to_write = min_t(size_t, count - i, avail / 2);
uart_console_write(uport, s + i, chars_to_write,
qcom_geni_serial_wr_char);
writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase +
writel(M_TX_FIFO_WATERMARK_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
i += chars_to_write;
}
@ -454,7 +438,7 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s,
else
spin_lock_irqsave(&uport->lock, flags);
geni_status = readl_relaxed(uport->membase + SE_GENI_STATUS);
geni_status = readl(uport->membase + SE_GENI_STATUS);
/* Cancel the current write to log the fault */
if (!locked) {
@ -464,11 +448,10 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s,
geni_se_abort_m_cmd(&port->se);
qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_ABORT_EN, true);
writel_relaxed(M_CMD_ABORT_EN, uport->membase +
writel(M_CMD_ABORT_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
}
writel_relaxed(M_CMD_CANCEL_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
} else if ((geni_status & M_GENI_CMD_ACTIVE) && !port->tx_remaining) {
/*
* It seems we can't interrupt existing transfers if all data
@ -477,9 +460,8 @@ static void qcom_geni_serial_console_write(struct console *co, const char *s,
qcom_geni_serial_poll_tx_done(uport);
if (uart_circ_chars_pending(&uport->state->xmit)) {
irq_en = readl_relaxed(uport->membase +
SE_GENI_M_IRQ_EN);
writel_relaxed(irq_en | M_TX_FIFO_WATERMARK_EN,
irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
writel(irq_en | M_TX_FIFO_WATERMARK_EN,
uport->membase + SE_GENI_M_IRQ_EN);
}
}
@ -567,15 +549,8 @@ static int handle_rx_uart(struct uart_port *uport, u32 bytes, bool drop)
static void qcom_geni_serial_start_tx(struct uart_port *uport)
{
u32 irq_en;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
u32 status;
if (port->xfer_mode == GENI_SE_FIFO) {
/*
* readl ensures reading & writing of IRQ_EN register
* is not re-ordered before checking the status of the
* Serial Engine.
*/
status = readl(uport->membase + SE_GENI_STATUS);
if (status & M_GENI_CMD_ACTIVE)
return;
@ -583,13 +558,11 @@ static void qcom_geni_serial_start_tx(struct uart_port *uport)
if (!qcom_geni_serial_tx_empty(uport))
return;
irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN;
writel_relaxed(port->tx_wm, uport->membase +
SE_GENI_TX_WATERMARK_REG);
writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
static void qcom_geni_serial_stop_tx(struct uart_port *uport)
@ -598,35 +571,24 @@ static void qcom_geni_serial_stop_tx(struct uart_port *uport)
u32 status;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
irq_en &= ~M_CMD_DONE_EN;
if (port->xfer_mode == GENI_SE_FIFO) {
irq_en &= ~M_TX_FIFO_WATERMARK_EN;
writel_relaxed(0, uport->membase +
SE_GENI_TX_WATERMARK_REG);
}
writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
status = readl_relaxed(uport->membase + SE_GENI_STATUS);
irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
irq_en &= ~(M_CMD_DONE_EN | M_TX_FIFO_WATERMARK_EN);
writel(0, uport->membase + SE_GENI_TX_WATERMARK_REG);
writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
status = readl(uport->membase + SE_GENI_STATUS);
/* Possible stop tx is called multiple times. */
if (!(status & M_GENI_CMD_ACTIVE))
return;
/*
* Ensure cancel command write is not re-ordered before checking
* the status of the Primary Sequencer.
*/
mb();
geni_se_cancel_m_cmd(&port->se);
if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_CANCEL_EN, true)) {
geni_se_abort_m_cmd(&port->se);
qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_ABORT_EN, true);
writel_relaxed(M_CMD_ABORT_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
}
writel_relaxed(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
}
static void qcom_geni_serial_start_rx(struct uart_port *uport)
@ -635,27 +597,19 @@ static void qcom_geni_serial_start_rx(struct uart_port *uport)
u32 status;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
status = readl_relaxed(uport->membase + SE_GENI_STATUS);
status = readl(uport->membase + SE_GENI_STATUS);
if (status & S_GENI_CMD_ACTIVE)
qcom_geni_serial_stop_rx(uport);
/*
* Ensure setup command write is not re-ordered before checking
* the status of the Secondary Sequencer.
*/
mb();
geni_se_setup_s_cmd(&port->se, UART_START_READ, 0);
if (port->xfer_mode == GENI_SE_FIFO) {
irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN);
irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN);
irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN;
writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN;
writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
static void qcom_geni_serial_stop_rx(struct uart_port *uport)
@ -665,32 +619,24 @@ static void qcom_geni_serial_stop_rx(struct uart_port *uport)
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
u32 irq_clear = S_CMD_DONE_EN;
if (port->xfer_mode == GENI_SE_FIFO) {
irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN);
irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN);
irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN);
writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN);
writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
status = readl_relaxed(uport->membase + SE_GENI_STATUS);
status = readl(uport->membase + SE_GENI_STATUS);
/* Possible stop rx is called multiple times. */
if (!(status & S_GENI_CMD_ACTIVE))
return;
/*
* Ensure cancel command write is not re-ordered before checking
* the status of the Secondary Sequencer.
*/
mb();
geni_se_cancel_s_cmd(&port->se);
qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG,
S_GENI_CMD_CANCEL, false);
status = readl_relaxed(uport->membase + SE_GENI_STATUS);
writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
status = readl(uport->membase + SE_GENI_STATUS);
writel(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
if (status & S_GENI_CMD_ACTIVE)
qcom_geni_serial_abort_rx(uport);
}
@ -704,7 +650,7 @@ static void qcom_geni_serial_handle_rx(struct uart_port *uport, bool drop)
u32 total_bytes;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS);
status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS);
word_cnt = status & RX_FIFO_WC_MSK;
last_word_partial = status & RX_LAST;
last_word_byte_cnt = (status & RX_LAST_BYTE_VALID_MSK) >>
@ -734,7 +680,7 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done,
unsigned int chunk;
int tail;
status = readl_relaxed(uport->membase + SE_GENI_TX_FIFO_STATUS);
status = readl(uport->membase + SE_GENI_TX_FIFO_STATUS);
/* Complete the current tx command before taking newly added data */
if (active)
@ -760,9 +706,9 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done,
qcom_geni_serial_setup_tx(uport, pending);
port->tx_remaining = pending;
irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
if (!(irq_en & M_TX_FIFO_WATERMARK_EN))
writel_relaxed(irq_en | M_TX_FIFO_WATERMARK_EN,
writel(irq_en | M_TX_FIFO_WATERMARK_EN,
uport->membase + SE_GENI_M_IRQ_EN);
}
@ -795,14 +741,14 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done,
* cleared it in qcom_geni_serial_isr it will have already reasserted
* so we must clear it again here after our writes.
*/
writel_relaxed(M_TX_FIFO_WATERMARK_EN,
writel(M_TX_FIFO_WATERMARK_EN,
uport->membase + SE_GENI_M_IRQ_CLEAR);
out_write_wakeup:
if (!port->tx_remaining) {
irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
if (irq_en & M_TX_FIFO_WATERMARK_EN)
writel_relaxed(irq_en & ~M_TX_FIFO_WATERMARK_EN,
writel(irq_en & ~M_TX_FIFO_WATERMARK_EN,
uport->membase + SE_GENI_M_IRQ_EN);
}
@ -812,12 +758,12 @@ static void qcom_geni_serial_handle_tx(struct uart_port *uport, bool done,
static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
{
unsigned int m_irq_status;
unsigned int s_irq_status;
unsigned int geni_status;
u32 m_irq_en;
u32 m_irq_status;
u32 s_irq_status;
u32 geni_status;
struct uart_port *uport = dev;
unsigned long flags;
unsigned int m_irq_en;
bool drop_rx = false;
struct tty_port *tport = &uport->state->port;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
@ -826,12 +772,12 @@ static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
return IRQ_NONE;
spin_lock_irqsave(&uport->lock, flags);
m_irq_status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS);
s_irq_status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS);
geni_status = readl_relaxed(uport->membase + SE_GENI_STATUS);
m_irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
writel_relaxed(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR);
writel_relaxed(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR);
m_irq_status = readl(uport->membase + SE_GENI_M_IRQ_STATUS);
s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS);
geni_status = readl(uport->membase + SE_GENI_STATUS);
m_irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
writel(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR);
writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR);
if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN))
goto out_unlock;
@ -877,17 +823,6 @@ static void get_tx_fifo_size(struct qcom_geni_serial_port *port)
(port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE;
}
static void set_rfr_wm(struct qcom_geni_serial_port *port)
{
/*
* Set RFR (Flow off) to FIFO_DEPTH - 2.
* RX WM level at 10% RX_FIFO_DEPTH.
* TX WM level at 10% TX_FIFO_DEPTH.
*/
port->rx_rfr = port->rx_fifo_depth - 2;
port->rx_wm = UART_CONSOLE_RX_WM;
port->tx_wm = DEF_TX_WM;
}
static void qcom_geni_serial_shutdown(struct uart_port *uport)
{
@ -907,7 +842,7 @@ static void qcom_geni_serial_shutdown(struct uart_port *uport)
static int qcom_geni_serial_port_setup(struct uart_port *uport)
{
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
unsigned int rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT;
u32 rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT;
u32 proto;
if (uart_console(uport)) {
@ -928,21 +863,19 @@ static int qcom_geni_serial_port_setup(struct uart_port *uport)
get_tx_fifo_size(port);
set_rfr_wm(port);
writel_relaxed(rxstale, uport->membase + SE_UART_RX_STALE_CNT);
writel(rxstale, uport->membase + SE_UART_RX_STALE_CNT);
/*
* Make an unconditional cancel on the main sequencer to reset
* it else we could end up in data loss scenarios.
*/
port->xfer_mode = GENI_SE_FIFO;
if (uart_console(uport))
qcom_geni_serial_poll_tx_done(uport);
geni_se_config_packing(&port->se, BITS_PER_BYTE, port->tx_bytes_pw,
false, true, false);
geni_se_config_packing(&port->se, BITS_PER_BYTE, port->rx_bytes_pw,
false, false, true);
geni_se_init(&port->se, port->rx_wm, port->rx_rfr);
geni_se_select_mode(&port->se, port->xfer_mode);
geni_se_init(&port->se, UART_RX_WM, port->rx_fifo_depth - 2);
geni_se_select_mode(&port->se, GENI_SE_FIFO);
if (!uart_console(uport)) {
port->rx_fifo = devm_kcalloc(uport->dev,
port->rx_fifo_depth, sizeof(u32), GFP_KERNEL);
@ -1008,14 +941,14 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport,
struct ktermios *termios, struct ktermios *old)
{
unsigned int baud;
unsigned int bits_per_char;
unsigned int tx_trans_cfg;
unsigned int tx_parity_cfg;
unsigned int rx_trans_cfg;
unsigned int rx_parity_cfg;
unsigned int stop_bit_len;
u32 bits_per_char;
u32 tx_trans_cfg;
u32 tx_parity_cfg;
u32 rx_trans_cfg;
u32 rx_parity_cfg;
u32 stop_bit_len;
unsigned int clk_div;
unsigned long ser_clk_cfg;
u32 ser_clk_cfg;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
unsigned long clk_rate;
@ -1033,10 +966,10 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport,
ser_clk_cfg |= clk_div << CLK_DIV_SHFT;
/* parity */
tx_trans_cfg = readl_relaxed(uport->membase + SE_UART_TX_TRANS_CFG);
tx_parity_cfg = readl_relaxed(uport->membase + SE_UART_TX_PARITY_CFG);
rx_trans_cfg = readl_relaxed(uport->membase + SE_UART_RX_TRANS_CFG);
rx_parity_cfg = readl_relaxed(uport->membase + SE_UART_RX_PARITY_CFG);
tx_trans_cfg = readl(uport->membase + SE_UART_TX_TRANS_CFG);
tx_parity_cfg = readl(uport->membase + SE_UART_TX_PARITY_CFG);
rx_trans_cfg = readl(uport->membase + SE_UART_RX_TRANS_CFG);
rx_parity_cfg = readl(uport->membase + SE_UART_RX_PARITY_CFG);
if (termios->c_cflag & PARENB) {
tx_trans_cfg |= UART_TX_PAR_EN;
rx_trans_cfg |= UART_RX_PAR_EN;
@ -1092,17 +1025,17 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport,
uart_update_timeout(uport, termios->c_cflag, baud);
if (!uart_console(uport))
writel_relaxed(port->loopback,
writel(port->loopback,
uport->membase + SE_UART_LOOPBACK_CFG);
writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG);
writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG);
writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
writel(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG);
writel(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG);
out_restart_rx:
qcom_geni_serial_start_rx(uport);
}
@ -1193,13 +1126,13 @@ static int __init qcom_geni_serial_earlycon_setup(struct earlycon_device *dev,
geni_se_init(&se, DEF_FIFO_DEPTH_WORDS / 2, DEF_FIFO_DEPTH_WORDS - 2);
geni_se_select_mode(&se, GENI_SE_FIFO);
writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
dev->con->write = qcom_geni_serial_earlycon_write;
dev->con->setup = NULL;

42
drivers/tty/serial/samsung.c
View File

@ -1694,6 +1694,42 @@ s3c24xx_serial_cpufreq_deregister(struct s3c24xx_uart_port *port)
}
#endif
static int s3c24xx_serial_enable_baudclk(struct s3c24xx_uart_port *ourport)
{
struct device *dev = ourport->port.dev;
struct s3c24xx_uart_info *info = ourport->info;
char clk_name[MAX_CLK_NAME_LENGTH];
unsigned int clk_sel;
struct clk *clk;
int clk_num;
int ret;
clk_sel = ourport->cfg->clk_sel ? : info->def_clk_sel;
for (clk_num = 0; clk_num < info->num_clks; clk_num++) {
if (!(clk_sel & (1 << clk_num)))
continue;
sprintf(clk_name, "clk_uart_baud%d", clk_num);
clk = clk_get(dev, clk_name);
if (IS_ERR(clk))
continue;
ret = clk_prepare_enable(clk);
if (ret) {
clk_put(clk);
continue;
}
ourport->baudclk = clk;
ourport->baudclk_rate = clk_get_rate(clk);
s3c24xx_serial_setsource(&ourport->port, clk_num);
return 0;
}
return -EINVAL;
}
/* s3c24xx_serial_init_port
*
* initialise a single serial port from the platform device given
@ -1788,6 +1824,10 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
goto err;
}
ret = s3c24xx_serial_enable_baudclk(ourport);
if (ret)
pr_warn("uart: failed to enable baudclk\n");
/* Keep all interrupts masked and cleared */
if (s3c24xx_serial_has_interrupt_mask(port)) {
wr_regl(port, S3C64XX_UINTM, 0xf);
@ -1901,6 +1941,8 @@ static int s3c24xx_serial_probe(struct platform_device *pdev)
* and keeps the clock enabled in this case.
*/
clk_disable_unprepare(ourport->clk);
if (!IS_ERR(ourport->baudclk))
clk_disable_unprepare(ourport->baudclk);
ret = s3c24xx_serial_cpufreq_register(ourport);
if (ret < 0)

4
drivers/tty/serial/sc16is7xx.c
View File

@ -1187,9 +1187,7 @@ static int sc16is7xx_probe(struct device *dev,
return PTR_ERR(regmap);
/* Alloc port structure */
s = devm_kzalloc(dev, sizeof(*s) +
sizeof(struct sc16is7xx_one) * devtype->nr_uart,
GFP_KERNEL);
s = devm_kzalloc(dev, struct_size(s, p, devtype->nr_uart), GFP_KERNEL);
if (!s) {
dev_err(dev, "Error allocating port structure\n");
return -ENOMEM;

2
drivers/tty/serial/serial_core.c
View File

@ -2844,7 +2844,7 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *uport)
*/
tty_dev = tty_port_register_device_attr_serdev(port, drv->tty_driver,
uport->line, uport->dev, port, uport->tty_groups);
if (likely(!IS_ERR(tty_dev))) {
if (!IS_ERR(tty_dev)) {
device_set_wakeup_capable(tty_dev, 1);
} else {
dev_err(uport->dev, "Cannot register tty device on line %d\n",

71
drivers/tty/serial/sh-sci.c
View File

@ -1243,12 +1243,22 @@ static int sci_dma_rx_find_active(struct sci_port *s)
return -1;
}
static void sci_rx_dma_release(struct sci_port *s)
static void sci_dma_rx_chan_invalidate(struct sci_port *s)
{
unsigned int i;
s->chan_rx = NULL;
for (i = 0; i < ARRAY_SIZE(s->cookie_rx); i++)
s->cookie_rx[i] = -EINVAL;
s->active_rx = 0;
}
static void sci_dma_rx_release(struct sci_port *s)
{
struct dma_chan *chan = s->chan_rx_saved;
s->chan_rx_saved = s->chan_rx = NULL;
s->cookie_rx[0] = s->cookie_rx[1] = -EINVAL;
s->chan_rx_saved = NULL;
sci_dma_rx_chan_invalidate(s);
dmaengine_terminate_sync(chan);
dma_free_coherent(chan->device->dev, s->buf_len_rx * 2, s->rx_buf[0],
sg_dma_address(&s->sg_rx[0]));
@ -1264,6 +1274,20 @@ static void start_hrtimer_us(struct hrtimer *hrt, unsigned long usec)
hrtimer_start(hrt, t, HRTIMER_MODE_REL);
}
static void sci_dma_rx_reenable_irq(struct sci_port *s)
{
struct uart_port *port = &s->port;
u16 scr;
/* Direct new serial port interrupts back to CPU */
scr = serial_port_in(port, SCSCR);
if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
scr &= ~SCSCR_RDRQE;
enable_irq(s->irqs[SCIx_RXI_IRQ]);
}
serial_port_out(port, SCSCR, scr | SCSCR_RIE);
}
static void sci_dma_rx_complete(void *arg)
{
struct sci_port *s = arg;
@ -1313,12 +1337,13 @@ static void sci_dma_rx_complete(void *arg)
dev_warn(port->dev, "Failed submitting Rx DMA descriptor\n");
/* Switch to PIO */
spin_lock_irqsave(&port->lock, flags);
s->chan_rx = NULL;
sci_start_rx(port);
dmaengine_terminate_async(chan);
sci_dma_rx_chan_invalidate(s);
sci_dma_rx_reenable_irq(s);
spin_unlock_irqrestore(&port->lock, flags);
}
static void sci_tx_dma_release(struct sci_port *s)
static void sci_dma_tx_release(struct sci_port *s)
{
struct dma_chan *chan = s->chan_tx_saved;
@ -1331,7 +1356,7 @@ static void sci_tx_dma_release(struct sci_port *s)
dma_release_channel(chan);
}
static int sci_submit_rx(struct sci_port *s, bool port_lock_held)
static int sci_dma_rx_submit(struct sci_port *s, bool port_lock_held)
{
struct dma_chan *chan = s->chan_rx;
struct uart_port *port = &s->port;
@ -1367,17 +1392,14 @@ static int sci_submit_rx(struct sci_port *s, bool port_lock_held)
spin_lock_irqsave(&port->lock, flags);
if (i)
dmaengine_terminate_async(chan);
for (i = 0; i < 2; i++)
s->cookie_rx[i] = -EINVAL;
s->active_rx = 0;
s->chan_rx = NULL;
sci_dma_rx_chan_invalidate(s);
sci_start_rx(port);
if (!port_lock_held)
spin_unlock_irqrestore(&port->lock, flags);
return -EAGAIN;
}
static void work_fn_tx(struct work_struct *work)
static void sci_dma_tx_work_fn(struct work_struct *work)
{
struct sci_port *s = container_of(work, struct sci_port, work_tx);
struct dma_async_tx_descriptor *desc;
@ -1436,7 +1458,7 @@ static void work_fn_tx(struct work_struct *work)
return;
}
static enum hrtimer_restart rx_timer_fn(struct hrtimer *t)
static enum hrtimer_restart sci_dma_rx_timer_fn(struct hrtimer *t)
{
struct sci_port *s = container_of(t, struct sci_port, rx_timer);
struct dma_chan *chan = s->chan_rx;
@ -1446,7 +1468,6 @@ static enum hrtimer_restart rx_timer_fn(struct hrtimer *t)
unsigned long flags;
unsigned int read;
int active, count;
u16 scr;
dev_dbg(port->dev, "DMA Rx timed out\n");
@ -1494,15 +1515,9 @@ static enum hrtimer_restart rx_timer_fn(struct hrtimer *t)
}
if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
sci_submit_rx(s, true);
sci_dma_rx_submit(s, true);
/* Direct new serial port interrupts back to CPU */
scr = serial_port_in(port, SCSCR);
if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
scr &= ~SCSCR_RDRQE;
enable_irq(s->irqs[SCIx_RXI_IRQ]);
}
serial_port_out(port, SCSCR, scr | SCSCR_RIE);
sci_dma_rx_reenable_irq(s);
spin_unlock_irqrestore(&port->lock, flags);
@ -1580,7 +1595,7 @@ static void sci_request_dma(struct uart_port *port)
__func__, UART_XMIT_SIZE,
port->state->xmit.buf, &s->tx_dma_addr);
INIT_WORK(&s->work_tx, work_fn_tx);
INIT_WORK(&s->work_tx, sci_dma_tx_work_fn);
s->chan_tx_saved = s->chan_tx = chan;
}
}
@ -1615,12 +1630,12 @@ static void sci_request_dma(struct uart_port *port)
}
hrtimer_init(&s->rx_timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
s->rx_timer.function = rx_timer_fn;
s->rx_timer.function = sci_dma_rx_timer_fn;
s->chan_rx_saved = s->chan_rx = chan;
if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
sci_submit_rx(s, false);
sci_dma_rx_submit(s, false);
}
}
@ -1629,9 +1644,9 @@ static void sci_free_dma(struct uart_port *port)
struct sci_port *s = to_sci_port(port);
if (s->chan_tx_saved)
sci_tx_dma_release(s);
sci_dma_tx_release(s);
if (s->chan_rx_saved)
sci_rx_dma_release(s);
sci_dma_rx_release(s);
}
static void sci_flush_buffer(struct uart_port *port)
@ -1669,7 +1684,7 @@ static irqreturn_t sci_rx_interrupt(int irq, void *ptr)
disable_irq_nosync(irq);
scr |= SCSCR_RDRQE;
} else {
if (sci_submit_rx(s, false) < 0)
if (sci_dma_rx_submit(s, false) < 0)
goto handle_pio;
scr &= ~SCSCR_RIE;

2
drivers/tty/serial/sprd_serial.c
View File

@ -371,7 +371,7 @@ static void sprd_set_termios(struct uart_port *port,
/* ask the core to calculate the divisor for us */
baud = uart_get_baud_rate(port, termios, old, 0, SPRD_BAUD_IO_LIMIT);
quot = (unsigned int)((port->uartclk + baud / 2) / baud);
quot = port->uartclk / baud;
/* set data length */
switch (termios->c_cflag & CSIZE) {

298
drivers/tty/serial/tegra-tcu.c Normal file
View File

@ -0,0 +1,298 @@
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (c) 2018, NVIDIA CORPORATION. All rights reserved.
*/
#include <linux/console.h>
#include <linux/mailbox_client.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/serial.h>
#include <linux/serial_core.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#define TCU_MBOX_BYTE(i, x) ((x) << (i * 8))
#define TCU_MBOX_BYTE_V(x, i) (((x) >> (i * 8)) & 0xff)
#define TCU_MBOX_NUM_BYTES(x) ((x) << 24)
#define TCU_MBOX_NUM_BYTES_V(x) (((x) >> 24) & 0x3)
struct tegra_tcu {
struct uart_driver driver;
#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE)
struct console console;
#endif
struct uart_port port;
struct mbox_client tx_client, rx_client;
struct mbox_chan *tx, *rx;
};
static unsigned int tegra_tcu_uart_tx_empty(struct uart_port *port)
{
return TIOCSER_TEMT;
}
static void tegra_tcu_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
}
static unsigned int tegra_tcu_uart_get_mctrl(struct uart_port *port)
{
return 0;
}
static void tegra_tcu_uart_stop_tx(struct uart_port *port)
{
}
static void tegra_tcu_write_one(struct tegra_tcu *tcu, u32 value,
unsigned int count)
{
void *msg;
value |= TCU_MBOX_NUM_BYTES(count);
msg = (void *)(unsigned long)value;
mbox_send_message(tcu->tx, msg);
mbox_flush(tcu->tx, 1000);
}
static void tegra_tcu_write(struct tegra_tcu *tcu, const char *s,
unsigned int count)
{
unsigned int written = 0, i = 0;
bool insert_nl = false;
u32 value = 0;
while (i < count) {
if (insert_nl) {
value |= TCU_MBOX_BYTE(written++, '\n');
insert_nl = false;
i++;
} else if (s[i] == '\n') {
value |= TCU_MBOX_BYTE(written++, '\r');
insert_nl = true;
} else {
value |= TCU_MBOX_BYTE(written++, s[i++]);
}
if (written == 3) {
tegra_tcu_write_one(tcu, value, 3);
value = written = 0;
}
}
if (written)
tegra_tcu_write_one(tcu, value, written);
}
static void tegra_tcu_uart_start_tx(struct uart_port *port)
{
struct tegra_tcu *tcu = port->private_data;
struct circ_buf *xmit = &port->state->xmit;
unsigned long count;
for (;;) {
count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
if (!count)
break;
tegra_tcu_write(tcu, &xmit->buf[xmit->tail], count);
xmit->tail = (xmit->tail + count) & (UART_XMIT_SIZE - 1);
}
uart_write_wakeup(port);
}
static void tegra_tcu_uart_stop_rx(struct uart_port *port)
{
}
static void tegra_tcu_uart_break_ctl(struct uart_port *port, int ctl)
{
}
static int tegra_tcu_uart_startup(struct uart_port *port)
{
return 0;
}
static void tegra_tcu_uart_shutdown(struct uart_port *port)
{
}
static void tegra_tcu_uart_set_termios(struct uart_port *port,
struct ktermios *new,
struct ktermios *old)
{
}
static const struct uart_ops tegra_tcu_uart_ops = {
.tx_empty = tegra_tcu_uart_tx_empty,
.set_mctrl = tegra_tcu_uart_set_mctrl,
.get_mctrl = tegra_tcu_uart_get_mctrl,
.stop_tx = tegra_tcu_uart_stop_tx,
.start_tx = tegra_tcu_uart_start_tx,
.stop_rx = tegra_tcu_uart_stop_rx,
.break_ctl = tegra_tcu_uart_break_ctl,
.startup = tegra_tcu_uart_startup,
.shutdown = tegra_tcu_uart_shutdown,
.set_termios = tegra_tcu_uart_set_termios,
};
#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE)
static void tegra_tcu_console_write(struct console *cons, const char *s,
unsigned int count)
{
struct tegra_tcu *tcu = container_of(cons, struct tegra_tcu, console);
tegra_tcu_write(tcu, s, count);
}
static int tegra_tcu_console_setup(struct console *cons, char *options)
{
return 0;
}
#endif
static void tegra_tcu_receive(struct mbox_client *cl, void *msg)
{
struct tegra_tcu *tcu = container_of(cl, struct tegra_tcu, rx_client);
struct tty_port *port = &tcu->port.state->port;
u32 value = (u32)(unsigned long)msg;
unsigned int num_bytes, i;
num_bytes = TCU_MBOX_NUM_BYTES_V(value);
for (i = 0; i < num_bytes; i++)
tty_insert_flip_char(port, TCU_MBOX_BYTE_V(value, i),
TTY_NORMAL);
tty_flip_buffer_push(port);
}
static int tegra_tcu_probe(struct platform_device *pdev)
{
struct uart_port *port;
struct tegra_tcu *tcu;
int err;
tcu = devm_kzalloc(&pdev->dev, sizeof(*tcu), GFP_KERNEL);
if (!tcu)
return -ENOMEM;
tcu->tx_client.dev = &pdev->dev;
tcu->rx_client.dev = &pdev->dev;
tcu->rx_client.rx_callback = tegra_tcu_receive;
tcu->tx = mbox_request_channel_byname(&tcu->tx_client, "tx");
if (IS_ERR(tcu->tx)) {
err = PTR_ERR(tcu->tx);
dev_err(&pdev->dev, "failed to get tx mailbox: %d\n", err);
return err;
}
tcu->rx = mbox_request_channel_byname(&tcu->rx_client, "rx");
if (IS_ERR(tcu->rx)) {
err = PTR_ERR(tcu->rx);
dev_err(&pdev->dev, "failed to get rx mailbox: %d\n", err);
goto free_tx;
}
#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE)
/* setup the console */
strcpy(tcu->console.name, "ttyTCU");
tcu->console.device = uart_console_device;
tcu->console.flags = CON_PRINTBUFFER | CON_ANYTIME;
tcu->console.index = -1;
tcu->console.write = tegra_tcu_console_write;
tcu->console.setup = tegra_tcu_console_setup;
tcu->console.data = &tcu->driver;
#endif
/* setup the driver */
tcu->driver.owner = THIS_MODULE;
tcu->driver.driver_name = "tegra-tcu";
tcu->driver.dev_name = "ttyTCU";
#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE)
tcu->driver.cons = &tcu->console;
#endif
tcu->driver.nr = 1;
err = uart_register_driver(&tcu->driver);
if (err) {
dev_err(&pdev->dev, "failed to register UART driver: %d\n",
err);
goto free_rx;
}
/* setup the port */
port = &tcu->port;
spin_lock_init(&port->lock);
port->dev = &pdev->dev;
port->type = PORT_TEGRA_TCU;
port->ops = &tegra_tcu_uart_ops;
port->fifosize = 1;
port->iotype = UPIO_MEM;
port->flags = UPF_BOOT_AUTOCONF;
port->private_data = tcu;
err = uart_add_one_port(&tcu->driver, port);
if (err) {
dev_err(&pdev->dev, "failed to add UART port: %d\n", err);
goto unregister_uart;
}
platform_set_drvdata(pdev, tcu);
#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE)
register_console(&tcu->console);
#endif
return 0;
unregister_uart:
uart_unregister_driver(&tcu->driver);
free_rx:
mbox_free_channel(tcu->rx);
free_tx:
mbox_free_channel(tcu->tx);
return err;
}
static int tegra_tcu_remove(struct platform_device *pdev)
{
struct tegra_tcu *tcu = platform_get_drvdata(pdev);
#if IS_ENABLED(CONFIG_SERIAL_TEGRA_TCU_CONSOLE)
unregister_console(&tcu->console);
#endif
uart_remove_one_port(&tcu->driver, &tcu->port);
uart_unregister_driver(&tcu->driver);
mbox_free_channel(tcu->rx);
mbox_free_channel(tcu->tx);
return 0;
}
static const struct of_device_id tegra_tcu_match[] = {
{ .compatible = "nvidia,tegra194-tcu" },
{ }
};
static struct platform_driver tegra_tcu_driver = {
.driver = {
.name = "tegra-tcu",
.of_match_table = tegra_tcu_match,
},
.probe = tegra_tcu_probe,
.remove = tegra_tcu_remove,
};
module_platform_driver(tegra_tcu_driver);
MODULE_AUTHOR("Mikko Perttunen <mperttunen@nvidia.com>");
MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("NVIDIA Tegra Combined UART driver");

42
drivers/tty/serial/xilinx_uartps.c
View File

@ -364,7 +364,13 @@ static irqreturn_t cdns_uart_isr(int irq, void *dev_id)
cdns_uart_handle_tx(dev_id);
isrstatus &= ~CDNS_UART_IXR_TXEMPTY;
}
if (isrstatus & CDNS_UART_IXR_RXMASK)
/*
* Skip RX processing if RX is disabled as RXEMPTY will never be set
* as read bytes will not be removed from the FIFO.
*/
if (isrstatus & CDNS_UART_IXR_RXMASK &&
!(readl(port->membase + CDNS_UART_CR) & CDNS_UART_CR_RX_DIS))
cdns_uart_handle_rx(dev_id, isrstatus);
spin_unlock(&port->lock);
@ -1547,29 +1553,35 @@ static int cdns_uart_probe(struct platform_device *pdev)
}
cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "pclk");
if (IS_ERR(cdns_uart_data->pclk)) {
cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "aper_clk");
if (!IS_ERR(cdns_uart_data->pclk))
dev_err(&pdev->dev, "clock name 'aper_clk' is deprecated.\n");
}
if (IS_ERR(cdns_uart_data->pclk)) {
dev_err(&pdev->dev, "pclk clock not found.\n");
if (PTR_ERR(cdns_uart_data->pclk) == -EPROBE_DEFER) {
rc = PTR_ERR(cdns_uart_data->pclk);
goto err_out_unregister_driver;
}
cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "uart_clk");
if (IS_ERR(cdns_uart_data->uartclk)) {
cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "ref_clk");
if (!IS_ERR(cdns_uart_data->uartclk))
dev_err(&pdev->dev, "clock name 'ref_clk' is deprecated.\n");
if (IS_ERR(cdns_uart_data->pclk)) {
cdns_uart_data->pclk = devm_clk_get(&pdev->dev, "aper_clk");
if (IS_ERR(cdns_uart_data->pclk)) {
rc = PTR_ERR(cdns_uart_data->pclk);
goto err_out_unregister_driver;
}
if (IS_ERR(cdns_uart_data->uartclk)) {
dev_err(&pdev->dev, "uart_clk clock not found.\n");
dev_err(&pdev->dev, "clock name 'aper_clk' is deprecated.\n");
}
cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "uart_clk");
if (PTR_ERR(cdns_uart_data->uartclk) == -EPROBE_DEFER) {
rc = PTR_ERR(cdns_uart_data->uartclk);
goto err_out_unregister_driver;
}
if (IS_ERR(cdns_uart_data->uartclk)) {
cdns_uart_data->uartclk = devm_clk_get(&pdev->dev, "ref_clk");
if (IS_ERR(cdns_uart_data->uartclk)) {
rc = PTR_ERR(cdns_uart_data->uartclk);
goto err_out_unregister_driver;
}
dev_err(&pdev->dev, "clock name 'ref_clk' is deprecated.\n");
}
rc = clk_prepare_enable(cdns_uart_data->pclk);
if (rc) {
dev_err(&pdev->dev, "Unable to enable pclk clock.\n");

54
drivers/tty/synclink.c
View File

@ -4325,41 +4325,6 @@ static int mgsl_init_tty(void)
return 0;
}
/* enumerate user specified ISA adapters
*/
static void mgsl_enum_isa_devices(void)
{
struct mgsl_struct *info;
int i;
/* Check for user specified ISA devices */
for (i=0 ;(i < MAX_ISA_DEVICES) && io[i] && irq[i]; i++){
if ( debug_level >= DEBUG_LEVEL_INFO )
printk("ISA device specified io=%04X,irq=%d,dma=%d\n",
io[i], irq[i], dma[i] );
info = mgsl_allocate_device();
if ( !info ) {
/* error allocating device instance data */
if ( debug_level >= DEBUG_LEVEL_ERROR )
printk( "can't allocate device instance data.\n");
continue;
}
/* Copy user configuration info to device instance data */
info->io_base = (unsigned int)io[i];
info->irq_level = (unsigned int)irq[i];
info->irq_level = irq_canonicalize(info->irq_level);
info->dma_level = (unsigned int)dma[i];
info->bus_type = MGSL_BUS_TYPE_ISA;
info->io_addr_size = 16;
info->irq_flags = 0;
mgsl_add_device( info );
}
}
static void synclink_cleanup(void)
{
int rc;
@ -4403,7 +4368,6 @@ static int __init synclink_init(void)
printk("%s %s\n", driver_name, driver_version);
mgsl_enum_isa_devices();
if ((rc = pci_register_driver(&synclink_pci_driver)) < 0)
printk("%s:failed to register PCI driver, error=%d\n",__FILE__,rc);
else
@ -5025,12 +4989,6 @@ static void usc_set_sdlc_mode( struct mgsl_struct *info )
info->mbre_bit = BIT8;
outw( BIT8, info->io_base ); /* set Master Bus Enable (DCAR) */
if (info->bus_type == MGSL_BUS_TYPE_ISA) {
/* Enable DMAEN (Port 7, Bit 14) */
/* This connects the DMA request signal to the ISA bus */
usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT15) & ~BIT14));
}
/* DMA Control Register (DCR)
*
* <15..14> 10 Priority mode = Alternating Tx/Rx
@ -6007,12 +5965,6 @@ static void usc_set_async_mode( struct mgsl_struct *info )
usc_EnableMasterIrqBit( info );
if (info->bus_type == MGSL_BUS_TYPE_ISA) {
/* Enable INTEN (Port 6, Bit12) */
/* This connects the IRQ request signal to the ISA bus */
usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) & ~BIT12));
}
if (info->params.loopback) {
info->loopback_bits = 0x300;
outw(0x0300, info->io_base + CCAR);
@ -6107,12 +6059,6 @@ static void usc_set_sync_mode( struct mgsl_struct *info )
usc_loopback_frame( info );
usc_set_sdlc_mode( info );
if (info->bus_type == MGSL_BUS_TYPE_ISA) {
/* Enable INTEN (Port 6, Bit12) */
/* This connects the IRQ request signal to the ISA bus */
usc_OutReg(info, PCR, (u16)((usc_InReg(info, PCR) | BIT13) & ~BIT12));
}
usc_enable_aux_clock(info, info->params.clock_speed);
if (info->params.loopback)

8
drivers/tty/sysrq.c
View File

@ -539,7 +539,6 @@ void __handle_sysrq(int key, bool check_mask)
*/
orig_log_level = console_loglevel;
console_loglevel = CONSOLE_LOGLEVEL_DEFAULT;
pr_info("SysRq : ");
op_p = __sysrq_get_key_op(key);
if (op_p) {
@ -548,14 +547,15 @@ void __handle_sysrq(int key, bool check_mask)
* should not) and is the invoked operation enabled?
*/
if (!check_mask || sysrq_on_mask(op_p->enable_mask)) {
pr_cont("%s\n", op_p->action_msg);
pr_info("%s\n", op_p->action_msg);
console_loglevel = orig_log_level;
op_p->handler(key);
} else {
pr_cont("This sysrq operation is disabled.\n");
pr_info("This sysrq operation is disabled.\n");
console_loglevel = orig_log_level;
}
} else {
pr_cont("HELP : ");
pr_info("HELP : ");
/* Only print the help msg once per handler */
for (i = 0; i < ARRAY_SIZE(sysrq_key_table); i++) {
if (sysrq_key_table[i]) {

2
drivers/tty/tty_buffer.c
View File

@ -26,7 +26,7 @@
* Byte threshold to limit memory consumption for flip buffers.
* The actual memory limit is > 2x this amount.
*/
#define TTYB_DEFAULT_MEM_LIMIT 65536
#define TTYB_DEFAULT_MEM_LIMIT (640 * 1024UL)
/*
* We default to dicing tty buffer allocations to this many characters

3
drivers/tty/tty_io.c
View File

@ -513,6 +513,8 @@ static const struct file_operations hung_up_tty_fops = {
static DEFINE_SPINLOCK(redirect_lock);
static struct file *redirect;
extern void tty_sysctl_init(void);
/**
* tty_wakeup - request more data
* @tty: terminal
@ -3483,6 +3485,7 @@ void console_sysfs_notify(void)
*/
int __init tty_init(void)
{
tty_sysctl_init();
cdev_init(&tty_cdev, &tty_fops);
if (cdev_add(&tty_cdev, MKDEV(TTYAUX_MAJOR, 0), 1) ||
register_chrdev_region(MKDEV(TTYAUX_MAJOR, 0), 1, "/dev/tty") < 0)

47
drivers/tty/tty_ldisc.c
View File

@ -156,6 +156,13 @@ static void put_ldops(struct tty_ldisc_ops *ldops)
* takes tty_ldiscs_lock to guard against ldisc races
*/
#if defined(CONFIG_LDISC_AUTOLOAD)
#define INITIAL_AUTOLOAD_STATE 1
#else
#define INITIAL_AUTOLOAD_STATE 0
#endif
static int tty_ldisc_autoload = INITIAL_AUTOLOAD_STATE;
static struct tty_ldisc *tty_ldisc_get(struct tty_struct *tty, int disc)
{
struct tty_ldisc *ld;
@ -170,6 +177,8 @@ static struct tty_ldisc *tty_ldisc_get(struct tty_struct *tty, int disc)
*/
ldops = get_ldops(disc);
if (IS_ERR(ldops)) {
if (!capable(CAP_SYS_MODULE) && !tty_ldisc_autoload)
return ERR_PTR(-EPERM);
request_module("tty-ldisc-%d", disc);
ldops = get_ldops(disc);
if (IS_ERR(ldops))
@ -845,3 +854,41 @@ void tty_ldisc_deinit(struct tty_struct *tty)
tty_ldisc_put(tty->ldisc);
tty->ldisc = NULL;
}
static int zero;
static int one = 1;
static struct ctl_table tty_table[] = {
{
.procname = "ldisc_autoload",
.data = &tty_ldisc_autoload,
.maxlen = sizeof(tty_ldisc_autoload),
.mode = 0644,
.proc_handler = proc_dointvec,
.extra1 = &zero,
.extra2 = &one,
},
{ }
};
static struct ctl_table tty_dir_table[] = {
{
.procname = "tty",
.mode = 0555,
.child = tty_table,
},
{ }
};
static struct ctl_table tty_root_table[] = {
{
.procname = "dev",
.mode = 0555,
.child = tty_dir_table,
},
{ }
};
void tty_sysctl_init(void)
{
register_sysctl_table(tty_root_table);
}

46
drivers/tty/vt/vc_screen.c
View File

@ -80,7 +80,7 @@
struct vcs_poll_data {
struct notifier_block notifier;
unsigned int cons_num;
bool seen_last_update;
int event;
wait_queue_head_t waitq;
struct fasync_struct *fasync;
};
@ -93,9 +93,18 @@ vcs_notifier(struct notifier_block *nb, unsigned long code, void *_param)
struct vcs_poll_data *poll =
container_of(nb, struct vcs_poll_data, notifier);
int currcons = poll->cons_num;
int fa_band;
if (code != VT_UPDATE)
switch (code) {
case VT_UPDATE:
fa_band = POLL_PRI;
break;
case VT_DEALLOCATE:
fa_band = POLL_HUP;
break;
default:
return NOTIFY_DONE;
}
if (currcons == 0)
currcons = fg_console;
@ -104,9 +113,9 @@ vcs_notifier(struct notifier_block *nb, unsigned long code, void *_param)
if (currcons != vc->vc_num)
return NOTIFY_DONE;
poll->seen_last_update = false;
poll->event = code;
wake_up_interruptible(&poll->waitq);
kill_fasync(&poll->fasync, SIGIO, POLL_IN);
kill_fasync(&poll->fasync, SIGIO, fa_band);
return NOTIFY_OK;
}
@ -131,6 +140,15 @@ vcs_poll_data_get(struct file *file)
poll->cons_num = console(file_inode(file));
init_waitqueue_head(&poll->waitq);
poll->notifier.notifier_call = vcs_notifier;
/*
* In order not to lose any update event, we must pretend one might
* have occurred before we have a chance to register our notifier.
* This is also how user space has come to detect which kernels
* support POLLPRI on /dev/vcs* devices i.e. using poll() with
* POLLPRI and a zero timeout.
*/
poll->event = VT_UPDATE;
if (register_vt_notifier(&poll->notifier) != 0) {
kfree(poll);
return NULL;
@ -261,7 +279,7 @@ vcs_read(struct file *file, char __user *buf, size_t count, loff_t *ppos)
poll = file->private_data;
if (count && poll)
poll->seen_last_update = true;
poll->event = 0;
read = 0;
ret = 0;
while (count) {
@ -335,8 +353,9 @@ vcs_read(struct file *file, char __user *buf, size_t count, loff_t *ppos)
if (p < HEADER_SIZE) {
size_t tmp_count;
con_buf0[0] = (char)vc->vc_rows;
con_buf0[1] = (char)vc->vc_cols;
/* clamp header values if they don't fit */
con_buf0[0] = min(vc->vc_rows, 0xFFu);
con_buf0[1] = min(vc->vc_cols, 0xFFu);
getconsxy(vc, con_buf0 + 2);
con_buf_start += p;
@ -615,12 +634,21 @@ static __poll_t
vcs_poll(struct file *file, poll_table *wait)
{
struct vcs_poll_data *poll = vcs_poll_data_get(file);
__poll_t ret = DEFAULT_POLLMASK|EPOLLERR|EPOLLPRI;
__poll_t ret = DEFAULT_POLLMASK|EPOLLERR;
if (poll) {
poll_wait(file, &poll->waitq, wait);
if (poll->seen_last_update)
switch (poll->event) {
case VT_UPDATE:
ret = DEFAULT_POLLMASK|EPOLLPRI;
break;
case VT_DEALLOCATE:
ret = DEFAULT_POLLMASK|EPOLLHUP|EPOLLERR;
break;
case 0:
ret = DEFAULT_POLLMASK;
break;
}
}
return ret;
}

73
drivers/tty/vt/vt.c
View File

@ -935,8 +935,11 @@ static void flush_scrollback(struct vc_data *vc)
{
WARN_CONSOLE_UNLOCKED();
set_origin(vc);
if (vc->vc_sw->con_flush_scrollback)
vc->vc_sw->con_flush_scrollback(vc);
else
vc->vc_sw->con_switch(vc);
}
/*
@ -1342,6 +1345,8 @@ struct vc_data *vc_deallocate(unsigned int currcons)
* VT102 emulator
*/
enum { EPecma = 0, EPdec, EPeq, EPgt, EPlt};
#define set_kbd(vc, x) vt_set_kbd_mode_bit((vc)->vc_num, (x))
#define clr_kbd(vc, x) vt_clr_kbd_mode_bit((vc)->vc_num, (x))
#define is_kbd(vc, x) vt_get_kbd_mode_bit((vc)->vc_num, (x))
@ -1503,8 +1508,10 @@ static void csi_J(struct vc_data *vc, int vpar)
count = ((vc->vc_pos - vc->vc_origin) >> 1) + 1;
start = (unsigned short *)vc->vc_origin;
break;
case 3: /* include scrollback */
flush_scrollback(vc);
/* fallthrough */
case 2: /* erase whole display */
case 3: /* (and scrollback buffer later) */
vc_uniscr_clear_lines(vc, 0, vc->vc_rows);
count = vc->vc_cols * vc->vc_rows;
start = (unsigned short *)vc->vc_origin;
@ -1513,13 +1520,7 @@ static void csi_J(struct vc_data *vc, int vpar)
return;
}
scr_memsetw(start, vc->vc_video_erase_char, 2 * count);
if (vpar == 3) {
set_origin(vc);
flush_scrollback(vc);
if (con_is_visible(vc))
update_screen(vc);
} else if (con_should_update(vc))
do_update_region(vc, (unsigned long) start, count);
update_region(vc, (unsigned long) start, count);
vc->vc_need_wrap = 0;
}
@ -1628,9 +1629,9 @@ static void rgb_background(struct vc_data *vc, const struct rgb *c)
/*
* ITU T.416 Higher colour modes. They break the usual properties of SGR codes
* and thus need to be detected and ignored by hand. Strictly speaking, that
* standard also wants : rather than ; as separators, contrary to ECMA-48, but
* no one produces such codes and almost no one accepts them.
* and thus need to be detected and ignored by hand. That standard also
* wants : rather than ; as separators but sequences containing : are currently
* completely ignored by the parser.
*
* Subcommands 3 (CMY) and 4 (CMYK) are so insane there's no point in
* supporting them.
@ -1815,7 +1816,7 @@ static void set_mode(struct vc_data *vc, int on_off)
int i;
for (i = 0; i <= vc->vc_npar; i++)
if (vc->vc_ques) {
if (vc->vc_priv == EPdec) {
switch(vc->vc_par[i]) { /* DEC private modes set/reset */
case 1: /* Cursor keys send ^[Ox/^[[x */
if (on_off)
@ -2022,7 +2023,7 @@ static void restore_cur(struct vc_data *vc)
}
enum { ESnormal, ESesc, ESsquare, ESgetpars, ESfunckey,
EShash, ESsetG0, ESsetG1, ESpercent, ESignore, ESnonstd,
EShash, ESsetG0, ESsetG1, ESpercent, EScsiignore, ESnonstd,
ESpalette, ESosc };
/* console_lock is held (except via vc_init()) */
@ -2031,7 +2032,7 @@ static void reset_terminal(struct vc_data *vc, int do_clear)
vc->vc_top = 0;
vc->vc_bottom = vc->vc_rows;
vc->vc_state = ESnormal;
vc->vc_ques = 0;
vc->vc_priv = EPecma;
vc->vc_translate = set_translate(LAT1_MAP, vc);
vc->vc_G0_charset = LAT1_MAP;
vc->vc_G1_charset = GRAF_MAP;
@ -2112,6 +2113,7 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c)
lf(vc);
if (!is_kbd(vc, lnm))
return;
/* fall through */
case 13:
cr(vc);
return;
@ -2234,9 +2236,22 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c)
vc->vc_state=ESfunckey;
return;
}
vc->vc_ques = (c == '?');
if (vc->vc_ques)
switch (c) {
case '?':
vc->vc_priv = EPdec;
return;
case '>':
vc->vc_priv = EPgt;
return;
case '=':
vc->vc_priv = EPeq;
return;
case '<':
vc->vc_priv = EPlt;
return;
}
vc->vc_priv = EPecma;
/* fall through */
case ESgetpars:
if (c == ';' && vc->vc_npar < NPAR - 1) {
vc->vc_npar++;
@ -2246,16 +2261,22 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c)
vc->vc_par[vc->vc_npar] += c - '0';
return;
}
if (c >= 0x20 && c <= 0x3f) { /* 0x2x, 0x3a and 0x3c - 0x3f */
vc->vc_state = EScsiignore;
return;
}
vc->vc_state = ESnormal;
switch(c) {
case 'h':
if (vc->vc_priv <= EPdec)
set_mode(vc, 1);
return;
case 'l':
if (vc->vc_priv <= EPdec)
set_mode(vc, 0);
return;
case 'c':
if (vc->vc_ques) {
if (vc->vc_priv == EPdec) {
if (vc->vc_par[0])
vc->vc_cursor_type = vc->vc_par[0] | (vc->vc_par[1] << 8) | (vc->vc_par[2] << 16);
else
@ -2264,7 +2285,7 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c)
}
break;
case 'm':
if (vc->vc_ques) {
if (vc->vc_priv == EPdec) {
clear_selection();
if (vc->vc_par[0])
vc->vc_complement_mask = vc->vc_par[0] << 8 | vc->vc_par[1];
@ -2274,7 +2295,7 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c)
}
break;
case 'n':
if (!vc->vc_ques) {
if (vc->vc_priv == EPecma) {
if (vc->vc_par[0] == 5)
status_report(tty);
else if (vc->vc_par[0] == 6)
@ -2282,8 +2303,8 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c)
}
return;
}
if (vc->vc_ques) {
vc->vc_ques = 0;
if (vc->vc_priv != EPecma) {
vc->vc_priv = EPecma;
return;
}
switch(c) {
@ -2406,6 +2427,11 @@ static void do_con_trol(struct tty_struct *tty, struct vc_data *vc, int c)
return;
}
return;
case EScsiignore:
if (c >= 20 && c <= 0x3f)
return;
vc->vc_state = ESnormal;
return;
case ESpercent:
vc->vc_state = ESnormal;
switch (c) {
@ -4591,8 +4617,9 @@ EXPORT_SYMBOL_GPL(screen_pos);
void getconsxy(struct vc_data *vc, unsigned char *p)
{
p[0] = vc->vc_x;
p[1] = vc->vc_y;
/* clamp values if they don't fit */
p[0] = min(vc->vc_x, 0xFFu);
p[1] = min(vc->vc_y, 0xFFu);
}
void putconsxy(struct vc_data *vc, unsigned char *p)

2
include/linux/console_struct.h
View File

@ -119,7 +119,7 @@ struct vc_data {
unsigned int vc_s_blink : 1;
unsigned int vc_s_reverse : 1;
/* misc */
unsigned int vc_ques : 1;
unsigned int vc_priv : 3;
unsigned int vc_need_wrap : 1;
unsigned int vc_can_do_color : 1;
unsigned int vc_report_mouse : 2;

3
include/uapi/linux/serial_core.h
View File

@ -79,6 +79,9 @@
/* Nuvoton UART */
#define PORT_NPCM 40
/* NVIDIA Tegra Combined UART */
#define PORT_TEGRA_TCU 41
/* Intel EG20 */
#define PORT_PCH_8LINE 44
#define PORT_PCH_2LINE 45