Merge remote-tracking branches 'asoc/topic/cs35l35', 'asoc/topic/cs53l30', 'asoc/topic/da7213', 'asoc/topic/dio2125' and 'asoc/topic/dwc' into asoc-next

Documentation/devicetree/bindings/sound/cs35l35.txt

@@ -0,0 +1,180 @@
+CS35L35 Boosted Speaker Amplifier
+
+Required properties:
+
+  - compatible : "cirrus,cs35l35"
+
+  - reg : the I2C address of the device for I2C
+
+  - VA-supply, VP-supply : power supplies for the device,
+    as covered in
+    Documentation/devicetree/bindings/regulator/regulator.txt.
+
+  - interrupt-parent : Specifies the phandle of the interrupt controller to
+    which the IRQs from CS35L35 are delivered to.
+  - interrupts : IRQ line info CS35L35.
+    (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+    for further information relating to interrupt properties)
+
+Optional properties:
+  - reset-gpios : gpio used to reset the amplifier
+
+  - cirrus,stereo-config : Boolean to determine if there are 2 AMPs for a
+  Stereo configuration
+
+  - cirrus,audio-channel : Set Location of Audio Signal on Serial Port
+  0 = Data Packet received on Left I2S Channel
+  1 = Data Packet received on Right I2S Channel
+
+  - cirrus,advisory-channel : Set Location of Advisory Signal on Serial Port
+  0 = Data Packet received on Left I2S Channel
+  1 = Data Packet received on Right I2S Channel
+
+  - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal
+  if 2 Devices share Boost BST_CTL
+
+  - cirrus,external-boost : Boolean to specify the device is using an external
+  boost supply, note that sharing a boost from another cs35l35 would constitute
+  using an external supply for the slave device
+
+  - cirrus,sp-drv-strength : Value for setting the Serial Port drive strength
+  Table 3-10 of the datasheet lists drive-strength specifications
+  0 = 1x (Default)
+  1 = .5x
+  - cirrus,sp-drv-unused : Determines how unused slots should be driven on the
+  Serial Port.
+  0 - Hi-Z
+  2 - Drive 0's (Default)
+  3 - Drive 1's
+
+  - cirrus,bst-pdn-fet-on : Boolean to determine if the Boost PDN control
+  powers down with a rectification FET On or Off. If VSPK is supplied
+  externally then FET is off.
+
+  - cirrus,boost-ctl-millivolt : Boost Voltage Value.  Configures the boost
+    converter's output voltage in mV. The range is from 2600mV to 9000mV with
+    increments of 100mV.
+    (Default) VP
+
+  - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
+  Configures the peak current by monitoring the current through the boost FET.
+  Range starts at 1680mA and goes to a maximum of 4480mA with increments of
+  110mA.
+  (Default) 2.46 Amps
+
+  - cirrus,amp-gain-zc : Boolean to determine if to use Amplifier gain-change
+  zero-cross
+
+Optional H/G Algorithm sub-node:
+
+  The cs35l35 node can have a single "cirrus,classh-internal-algo" sub-node
+  that will disable automatic control of the internal H/G Algorithm.
+
+  It is strongly recommended that the Datasheet be referenced when adjusting
+  or using these Class H Algorithm controls over the internal Algorithm.
+  Serious damage can occur to the Device and surrounding components.
+
+  - cirrus,classh-internal-algo : Sub-node for the Internal Class H Algorithm
+  See Section 4.3 Internal Class H Algorithm in the Datasheet.
+  If not used, the device manages the ClassH Algorithm internally.
+
+Optional properties for the "cirrus,classh-internal-algo" Sub-node
+
+  Section 7.29 Class H Control
+  - cirrus,classh-bst-overide : Boolean
+  - cirrus,classh-bst-max-limit
+  - cirrus,classh-mem-depth
+
+  Section 7.30 Class H Headroom Control
+  - cirrus,classh-headroom
+
+  Section 7.31 Class H Release Rate
+  - cirrus,classh-release-rate
+
+  Section 7.32 Class H Weak FET Drive Control
+  - cirrus,classh-wk-fet-disable
+  - cirrus,classh-wk-fet-delay
+  - cirrus,classh-wk-fet-thld
+
+  Section 7.34 Class H VP Control
+  - cirrus,classh-vpch-auto
+  - cirrus,classh-vpch-rate
+  - cirrus,classh-vpch-man
+
+Optional Monitor Signal Format sub-node:
+
+  The cs35l35 node can have a single "cirrus,monitor-signal-format" sub-node
+  for adjusting the Depth, Location and Frame of the Monitoring Signals
+  for Algorithms.
+
+  See Sections 4.8.2 through 4.8.4 Serial-Port Control in the Datasheet
+
+  -cirrus,monitor-signal-format : Sub-node for the Monitor Signaling Formating
+  on the I2S Port. Each of the 3 8 bit values in the array contain the settings
+  for depth, location, and frame.
+
+  If not used, the defaults for the 6 monitor signals is used.
+
+  Sections 7.44 - 7.53 lists values for the depth, location, and frame
+  for each monitoring signal.
+
+  - cirrus,imon : 4 8 bit values to set the depth, location, frame and ADC
+  scale of the IMON monitor signal.
+
+  - cirrus,vmon : 3 8 bit values to set the depth, location, and frame
+  of the VMON monitor signal.
+
+  - cirrus,vpmon : 3 8 bit values to set the depth, location, and frame
+  of the VPMON monitor signal.
+
+  - cirrus,vbstmon : 3 8 bit values to set the depth, location, and frame
+  of the VBSTMON monitor signal
+
+  - cirrus,vpbrstat : 3 8 bit values to set the depth, location, and frame
+  of the VPBRSTAT monitor signal
+
+  - cirrus,zerofill : 3 8 bit values to set the depth, location, and frame\
+  of the ZEROFILL packet in the monitor signal
+
+Example:
+
+cs35l35: cs35l35@20 {
+	compatible = "cirrus,cs35l35";
+	reg = <0x20>;
+	VA-supply = <&dummy_vreg>;
+	VP-supply = <&dummy_vreg>;
+	reset-gpios = <&axi_gpio 54 0>;
+	interrupt-parent = <&gpio8>;
+	interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+	cirrus,boost-ctl-millivolt = <9000>;
+
+	cirrus,stereo-config;
+	cirrus,audio-channel = <0x00>;
+	cirrus,advisory-channel = <0x01>;
+	cirrus,shared-boost;
+
+	cirrus,classh-internal-algo {
+		cirrus,classh-bst-overide;
+		cirrus,classh-bst-max-limit = <0x01>;
+		cirrus,classh-mem-depth = <0x01>;
+		cirrus,classh-release-rate = <0x08>;
+		cirrus,classh-headroom-millivolt = <0x0B>;
+		cirrus,classh-wk-fet-disable = <0x01>;
+		cirrus,classh-wk-fet-delay = <0x04>;
+		cirrus,classh-wk-fet-thld = <0x01>;
+		cirrus,classh-vpch-auto = <0x01>;
+		cirrus,classh-vpch-rate = <0x02>;
+		cirrus,classh-vpch-man = <0x05>;
+	};
+
+	/* Depth, Location, Frame */
+	cirrus,monitor-signal-format {
+		cirrus,imon = /bits/ 8 <0x03 0x00 0x01>;
+		cirrus,vmon = /bits/ 8 <0x03 0x00 0x00>;
+		cirrus,vpmon = /bits/ 8 <0x03 0x04 0x00>;
+		cirrus,vbstmon = /bits/ 8 <0x03 0x04 0x01>;
+		cirrus,vpbrstat = /bits/ 8 <0x00 0x04 0x00>;
+		cirrus,zerofill = /bits/ 8 <0x00 0x00 0x00>;
+	};
+
+};

Documentation/devicetree/bindings/sound/dioo,dio2125.txt

@@ -0,0 +1,12 @@
+DIO2125 Audio Driver
+
+Required properties:
+- compatible : "dioo,dio2125"
+- enable-gpios : the gpio connected to the enable pin of the dio2125
+
+Example:
+
+amp: analog-amplifier {
+	compatible = "dioo,dio2125";
+	enable-gpios = <&gpio GPIOH_3 0>;
+};

include/sound/cs35l35.h

@@ -0,0 +1,108 @@
+/*
+ * linux/sound/cs35l35.h -- Platform data for CS35l35
+ *
+ * Copyright (c) 2016 Cirrus Logic Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __CS35L35_H
+#define __CS35L35_H
+
+struct classh_cfg {
+	/*
+	 * Class H Algorithm Control Variables
+	 * You can either have it done
+	 * automatically or you can adjust
+	 * these variables for tuning
+	 *
+	 * if you do not enable the internal algorithm
+	 * you will get a set of mixer controls for
+	 * Class H tuning
+	 *
+	 * Section 4.3 of the datasheet
+	 */
+	bool classh_bst_override;
+	bool classh_algo_enable;
+	int classh_bst_max_limit;
+	int classh_mem_depth;
+	int classh_release_rate;
+	int classh_headroom;
+	int classh_wk_fet_disable;
+	int classh_wk_fet_delay;
+	int classh_wk_fet_thld;
+	int classh_vpch_auto;
+	int classh_vpch_rate;
+	int classh_vpch_man;
+};
+
+struct monitor_cfg {
+	/*
+	 * Signal Monitor Data
+	 * highly configurable signal monitoring
+	 * data positioning and different types of
+	 * monitoring data.
+	 *
+	 * Section 4.8.2 - 4.8.4 of the datasheet
+	 */
+	bool is_present;
+	bool imon_specs;
+	bool vmon_specs;
+	bool vpmon_specs;
+	bool vbstmon_specs;
+	bool vpbrstat_specs;
+	bool zerofill_specs;
+	u8 imon_dpth;
+	u8 imon_loc;
+	u8 imon_frm;
+	u8 imon_scale;
+	u8 vmon_dpth;
+	u8 vmon_loc;
+	u8 vmon_frm;
+	u8 vpmon_dpth;
+	u8 vpmon_loc;
+	u8 vpmon_frm;
+	u8 vbstmon_dpth;
+	u8 vbstmon_loc;
+	u8 vbstmon_frm;
+	u8 vpbrstat_dpth;
+	u8 vpbrstat_loc;
+	u8 vpbrstat_frm;
+	u8 zerofill_dpth;
+	u8 zerofill_loc;
+	u8 zerofill_frm;
+};
+
+struct cs35l35_platform_data {
+
+	/* Stereo (2 Device) */
+	bool stereo;
+	/* serial port drive strength */
+	int sp_drv_str;
+	/* serial port drive in unused slots */
+	int sp_drv_unused;
+	/* Boost Power Down with FET */
+	bool bst_pdn_fet_on;
+	/* Boost Voltage : used if ClassH Algo Enabled */
+	int bst_vctl;
+	/* Boost Converter Peak Current CTRL */
+	int bst_ipk;
+	/* Amp Gain Zero Cross */
+	bool gain_zc;
+	/* Audio Input Location */
+	int aud_channel;
+	/* Advisory Input Location */
+	int adv_channel;
+	/* Shared Boost for stereo */
+	bool shared_bst;
+	/* Specifies this amp is using an external boost supply */
+	bool ext_bst;
+	/* ClassH Algorithm */
+	struct classh_cfg classh_algo;
+	/* Monitor Config */
+	struct monitor_cfg mon_cfg;
+};
+
+#endif /* __CS35L35_H */

sound/soc/codecs/Kconfig

@@ -49,6 +49,7 @@ config SND_SOC_ALL_CODECS
 	select SND_SOC_CS35L32 if I2C
 	select SND_SOC_CS35L33 if I2C
 	select SND_SOC_CS35L34 if I2C
+	select SND_SOC_CS35L35 if I2C
 	select SND_SOC_CS42L42 if I2C
 	select SND_SOC_CS42L51_I2C if I2C
 	select SND_SOC_CS42L52 if I2C && INPUT
@@ -69,6 +70,7 @@ config SND_SOC_ALL_CODECS
 	select SND_SOC_DA7219 if I2C
 	select SND_SOC_DA732X if I2C
 	select SND_SOC_DA9055 if I2C
+	select SND_SOC_DIO2125
 	select SND_SOC_DMIC
 	select SND_SOC_ES8328_SPI if SPI_MASTER
 	select SND_SOC_ES8328_I2C if I2C
@@ -410,6 +412,10 @@ config SND_SOC_CS35L34
 	tristate "Cirrus Logic CS35L34 CODEC"
 	depends on I2C
 
+config SND_SOC_CS35L35
+	tristate "Cirrus Logic CS35L35 CODEC"
+	depends on I2C
+
 config SND_SOC_CS42L42
 	tristate "Cirrus Logic CS42L42 CODEC"
 	depends on I2C
@@ -518,6 +524,10 @@ config SND_SOC_DA732X
 config SND_SOC_DA9055
 	tristate
 
+config SND_SOC_DIO2125
+	tristate "Dioo DIO2125 Amplifier"
+	select GPIOLIB
+
 config SND_SOC_DMIC
 	tristate
 

sound/soc/codecs/Makefile

@@ -39,6 +39,7 @@ snd-soc-cq93vc-objs := cq93vc.o
 snd-soc-cs35l32-objs := cs35l32.o
 snd-soc-cs35l33-objs := cs35l33.o
 snd-soc-cs35l34-objs := cs35l34.o
+snd-soc-cs35l35-objs := cs35l35.o
 snd-soc-cs42l42-objs := cs42l42.o
 snd-soc-cs42l51-objs := cs42l51.o
 snd-soc-cs42l51-i2c-objs := cs42l51-i2c.o
@@ -221,6 +222,7 @@ snd-soc-wm9712-objs := wm9712.o
 snd-soc-wm9713-objs := wm9713.o
 snd-soc-wm-hubs-objs := wm_hubs.o
 # Amp
+snd-soc-dio2125-objs := dio2125.o
 snd-soc-max9877-objs := max9877.o
 snd-soc-max98504-objs := max98504.o
 snd-soc-tpa6130a2-objs := tpa6130a2.o
@@ -269,6 +271,7 @@ obj-$(CONFIG_SND_SOC_CQ0093VC) += snd-soc-cq93vc.o
 obj-$(CONFIG_SND_SOC_CS35L32)	+= snd-soc-cs35l32.o
 obj-$(CONFIG_SND_SOC_CS35L33)	+= snd-soc-cs35l33.o
 obj-$(CONFIG_SND_SOC_CS35L34)	+= snd-soc-cs35l34.o
+obj-$(CONFIG_SND_SOC_CS35L35)	+= snd-soc-cs35l35.o
 obj-$(CONFIG_SND_SOC_CS42L42)	+= snd-soc-cs42l42.o
 obj-$(CONFIG_SND_SOC_CS42L51)	+= snd-soc-cs42l51.o
 obj-$(CONFIG_SND_SOC_CS42L51_I2C)	+= snd-soc-cs42l51-i2c.o
@@ -448,6 +451,7 @@ obj-$(CONFIG_SND_SOC_WM_ADSP)	+= snd-soc-wm-adsp.o
 obj-$(CONFIG_SND_SOC_WM_HUBS)	+= snd-soc-wm-hubs.o
 
 # Amp
+obj-$(CONFIG_SND_SOC_DIO2125)	+= snd-soc-dio2125.o
 obj-$(CONFIG_SND_SOC_MAX9877)	+= snd-soc-max9877.o
 obj-$(CONFIG_SND_SOC_MAX98504)	+= snd-soc-max98504.o
 obj-$(CONFIG_SND_SOC_TPA6130A2)	+= snd-soc-tpa6130a2.o

sound/soc/codecs/cs35l35.h

@@ -0,0 +1,294 @@
+/*
+ * cs35l35.h -- CS35L35 ALSA SoC audio driver
+ *
+ * Copyright 2016 Cirrus Logic, Inc.
+ *
+ * Author: Brian Austin <brian.austin@cirrus.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __CS35L35_H__
+#define __CS35L35_H__
+
+#define CS35L35_FIRSTREG		0x01
+#define CS35L35_LASTREG			0x7E
+#define CS35L35_CHIP_ID			0x00035A35
+#define CS35L35_DEVID_AB		0x01	/* Device ID A & B [RO] */
+#define CS35L35_DEVID_CD		0x02    /* Device ID C & D [RO] */
+#define CS35L35_DEVID_E			0x03    /* Device ID E [RO] */
+#define CS35L35_FAB_ID			0x04	/* Fab ID [RO] */
+#define CS35L35_REV_ID			0x05	/* Revision ID [RO] */
+#define CS35L35_PWRCTL1			0x06    /* Power Ctl 1 */
+#define CS35L35_PWRCTL2			0x07    /* Power Ctl 2 */
+#define CS35L35_PWRCTL3			0x08	/* Power Ctl 3 */
+#define CS35L35_CLK_CTL1		0x0A	/* Clocking Ctl 1 */
+#define CS35L35_CLK_CTL2		0x0B	/* Clocking Ctl 2 */
+#define CS35L35_CLK_CTL3		0x0C	/* Clocking Ctl 3 */
+#define CS35L35_SP_FMT_CTL1		0x0D	/* Serial Port Format CTL1 */
+#define CS35L35_SP_FMT_CTL2		0x0E	/* Serial Port Format CTL2 */
+#define CS35L35_SP_FMT_CTL3		0x0F	/* Serial Port Format CTL3 */
+#define CS35L35_MAG_COMP_CTL		0x13	/* Magnitude Comp CTL */
+#define CS35L35_AMP_INP_DRV_CTL		0x14	/* Amp Input Drive Ctl */
+#define CS35L35_AMP_DIG_VOL_CTL		0x15	/* Amplifier Dig Volume Ctl */
+#define CS35L35_AMP_DIG_VOL		0x16	/* Amplifier Dig Volume */
+#define CS35L35_ADV_DIG_VOL		0x17	/* Advisory Digital Volume */
+#define CS35L35_PROTECT_CTL		0x18	/* Amp Gain - Prot Ctl Param */
+#define CS35L35_AMP_GAIN_AUD_CTL	0x19	/* Amp Serial Port Gain Ctl */
+#define CS35L35_AMP_GAIN_PDM_CTL	0x1A	/* Amplifier Gain PDM Ctl */
+#define CS35L35_AMP_GAIN_ADV_CTL	0x1B	/* Amplifier Gain Ctl */
+#define CS35L35_GPI_CTL			0x1C	/* GPI Ctl */
+#define CS35L35_BST_CVTR_V_CTL		0x1D	/* Boost Conv Voltage Ctl */
+#define CS35L35_BST_PEAK_I		0x1E	/* Boost Conv Peak Current */
+#define CS35L35_BST_RAMP_CTL		0x20	/* Boost Conv Soft Ramp Ctl */
+#define CS35L35_BST_CONV_COEF_1		0x21	/* Boost Conv Coefficients 1 */
+#define CS35L35_BST_CONV_COEF_2		0x22	/* Boost Conv Coefficients 2 */
+#define CS35L35_BST_CONV_SLOPE_COMP	0x23	/* Boost Conv Slope Comp */
+#define CS35L35_BST_CONV_SW_FREQ	0x24	/* Boost Conv L BST SW Freq */
+#define CS35L35_CLASS_H_CTL		0x30	/* CLS H Control */
+#define CS35L35_CLASS_H_HEADRM_CTL	0x31	/* CLS H Headroom Ctl */
+#define CS35L35_CLASS_H_RELEASE_RATE	0x32	/* CLS H Release Rate */
+#define CS35L35_CLASS_H_FET_DRIVE_CTL	0x33	/* CLS H Weak FET Drive Ctl */
+#define CS35L35_CLASS_H_VP_CTL		0x34	/* CLS H VP Ctl */
+#define CS35L35_CLASS_H_STATUS		0x38	/* CLS H Status */
+#define CS35L35_VPBR_CTL		0x3A	/* VPBR Ctl */
+#define CS35L35_VPBR_VOL_CTL		0x3B	/* VPBR Volume Ctl */
+#define CS35L35_VPBR_TIMING_CTL		0x3C	/* VPBR Timing Ctl */
+#define CS35L35_VPBR_MODE_VOL_CTL	0x3D	/* VPBR Mode/Attack Vol Ctl */
+#define CS35L35_VPBR_ATTEN_STATUS	0x4B	/* VPBR Attenuation Status */
+#define CS35L35_SPKR_MON_CTL		0x4E	/* Speaker Monitoring Ctl */
+#define CS35L35_IMON_SCALE_CTL		0x51	/* IMON Scale Ctl */
+#define CS35L35_AUDIN_RXLOC_CTL		0x52	/* Audio Input RX Loc Ctl */
+#define CS35L35_ADVIN_RXLOC_CTL		0x53	/* Advisory Input RX Loc Ctl */
+#define CS35L35_VMON_TXLOC_CTL		0x54	/* VMON TX Loc Ctl */
+#define CS35L35_IMON_TXLOC_CTL		0x55	/* IMON TX Loc Ctl */
+#define CS35L35_VPMON_TXLOC_CTL		0x56	/* VPMON TX Loc Ctl */
+#define CS35L35_VBSTMON_TXLOC_CTL	0x57	/* VBSTMON TX Loc Ctl */
+#define CS35L35_VPBR_STATUS_TXLOC_CTL	0x58	/* VPBR Status TX Loc Ctl */
+#define CS35L35_ZERO_FILL_LOC_CTL	0x59	/* Zero Fill Loc Ctl */
+#define CS35L35_AUDIN_DEPTH_CTL		0x5A	/* Audio Input Depth Ctl */
+#define CS35L35_SPKMON_DEPTH_CTL	0x5B	/* SPK Mon Output Depth Ctl */
+#define CS35L35_SUPMON_DEPTH_CTL	0x5C	/* Supply Mon Out Depth Ctl */
+#define CS35L35_ZEROFILL_DEPTH_CTL	0x5D	/* Zero Fill Mon Output Ctl */
+#define CS35L35_MULT_DEV_SYNCH1		0x62	/* Multidevice Synch */
+#define CS35L35_MULT_DEV_SYNCH2		0x63	/* Multidevice Synch 2 */
+#define CS35L35_PROT_RELEASE_CTL	0x64	/* Protection Release Ctl */
+#define CS35L35_DIAG_MODE_REG_LOCK	0x68	/* Diagnostic Mode Reg Lock */
+#define CS35L35_DIAG_MODE_CTL_1		0x69	/* Diagnostic Mode Ctl 1 */
+#define CS35L35_DIAG_MODE_CTL_2		0x6A	/* Diagnostic Mode Ctl 2 */
+#define CS35L35_INT_MASK_1		0x70	/* Interrupt Mask 1 */
+#define CS35L35_INT_MASK_2		0x71	/* Interrupt Mask 2 */
+#define CS35L35_INT_MASK_3		0x72	/* Interrupt Mask 3 */
+#define CS35L35_INT_MASK_4		0x73	/* Interrupt Mask 4 */
+#define CS35L35_INT_STATUS_1		0x74	/* Interrupt Status 1 */
+#define CS35L35_INT_STATUS_2		0x75	/* Interrupt Status 2 */
+#define CS35L35_INT_STATUS_3		0x76	/* Interrupt Status 3 */
+#define CS35L35_INT_STATUS_4		0x77	/* Interrupt Status 4 */
+#define CS35L35_PLL_STATUS		0x78	/* PLL Status */
+#define CS35L35_OTP_TRIM_STATUS		0x7E	/* OTP Trim Status */
+
+#define CS35L35_MAX_REGISTER		0x7F
+
+/* CS35L35_PWRCTL1 */
+#define CS35L35_SFT_RST			0x80
+#define CS35L35_DISCHG_FLT		0x02
+#define CS35L35_PDN_ALL			0x01
+
+/* CS35L35_PWRCTL2 */
+#define CS35L35_PDN_VMON		0x80
+#define CS35L35_PDN_IMON		0x40
+#define CS35L35_PDN_CLASSH		0x20
+#define CS35L35_PDN_VPBR		0x10
+#define CS35L35_PDN_BST			0x04
+#define CS35L35_PDN_AMP			0x01
+
+/* CS35L35_PWRCTL3 */
+#define CS35L35_PDN_VBSTMON_OUT		0x10
+#define CS35L35_PDN_VMON_OUT		0x08
+
+#define CS35L35_AUDIN_DEPTH_MASK	0x03
+#define CS35L35_AUDIN_DEPTH_SHIFT	0
+#define CS35L35_ADVIN_DEPTH_MASK	0x0C
+#define CS35L35_ADVIN_DEPTH_SHIFT	2
+#define CS35L35_SDIN_DEPTH_8		0x01
+#define CS35L35_SDIN_DEPTH_16		0x02
+#define CS35L35_SDIN_DEPTH_24		0x03
+
+#define CS35L35_SDOUT_DEPTH_8		0x01
+#define CS35L35_SDOUT_DEPTH_12		0x02
+#define CS35L35_SDOUT_DEPTH_16		0x03
+
+#define CS35L35_AUD_IN_LR_MASK		0x80
+#define CS35L35_AUD_IN_LR_SHIFT		7
+#define CS35L35_ADV_IN_LR_MASK		0x80
+#define CS35L35_ADV_IN_LR_SHIFT		7
+#define CS35L35_AUD_IN_LOC_MASK		0x0F
+#define CS35L35_AUD_IN_LOC_SHIFT	0
+#define CS35L35_ADV_IN_LOC_MASK		0x0F
+#define CS35L35_ADV_IN_LOC_SHIFT	0
+
+#define CS35L35_IMON_DEPTH_MASK		0x03
+#define CS35L35_IMON_DEPTH_SHIFT	0
+#define CS35L35_VMON_DEPTH_MASK		0x0C
+#define CS35L35_VMON_DEPTH_SHIFT	2
+#define CS35L35_VBSTMON_DEPTH_MASK	0x03
+#define CS35L35_VBSTMON_DEPTH_SHIFT	0
+#define CS35L35_VPMON_DEPTH_MASK	0x0C
+#define CS35L35_VPMON_DEPTH_SHIFT	2
+#define CS35L35_VPBRSTAT_DEPTH_MASK	0x30
+#define CS35L35_VPBRSTAT_DEPTH_SHIFT	4
+#define CS35L35_ZEROFILL_DEPTH_MASK	0x03
+#define CS35L35_ZEROFILL_DEPTH_SHIFT	0x00
+
+#define CS35L35_MON_TXLOC_MASK		0x3F
+#define CS35L35_MON_TXLOC_SHIFT		0
+#define CS35L35_MON_FRM_MASK		0x80
+#define CS35L35_MON_FRM_SHIFT		7
+
+#define CS35L35_IMON_SCALE_MASK		0xF8
+#define CS35L35_IMON_SCALE_SHIFT	3
+
+#define CS35L35_MS_MASK			0x80
+#define CS35L35_MS_SHIFT		7
+#define CS35L35_SPMODE_MASK		0x40
+#define CS35L35_SP_DRV_MASK		0x10
+#define CS35L35_SP_DRV_SHIFT		4
+#define CS35L35_CLK_CTL2_MASK		0xFF
+#define CS35L35_PDM_MODE_MASK		0x40
+#define CS35L35_PDM_MODE_SHIFT		6
+#define CS35L35_CLK_SOURCE_MASK		0x03
+#define CS35L35_CLK_SOURCE_SHIFT	0
+#define CS35L35_CLK_SOURCE_MCLK		0
+#define CS35L35_CLK_SOURCE_SCLK		1
+#define CS35L35_CLK_SOURCE_PDM		2
+
+#define CS35L35_SP_SCLKS_MASK		0x0F
+#define CS35L35_SP_SCLKS_SHIFT		0x00
+#define CS35L35_SP_SCLKS_16FS		0x03
+#define CS35L35_SP_SCLKS_32FS		0x07
+#define CS35L35_SP_SCLKS_48FS		0x0B
+#define CS35L35_SP_SCLKS_64FS		0x0F
+#define CS35L35_SP_RATE_MASK		0xC0
+
+#define CS35L35_PDN_BST_MASK		0x06
+#define CS35L35_PDN_BST_FETON_SHIFT	1
+#define CS35L35_PDN_BST_FETOFF_SHIFT	2
+#define CS35L35_PWR2_PDN_MASK		0xE0
+#define CS35L35_PWR3_PDN_MASK		0x1E
+#define CS35L35_PDN_ALL_MASK		0x01
+#define CS35L35_DISCHG_FILT_MASK	0x02
+#define CS35L35_DISCHG_FILT_SHIFT	1
+#define CS35L35_MCLK_DIS_MASK		0x04
+#define CS35L35_MCLK_DIS_SHIFT		2
+
+#define CS35L35_BST_CTL_MASK		0x7F
+#define CS35L35_BST_CTL_SHIFT		0
+#define CS35L35_BST_IPK_MASK		0x1F
+#define CS35L35_BST_IPK_SHIFT		0
+#define CS35L35_AMP_MUTE_MASK		0x20
+#define CS35L35_AMP_MUTE_SHIFT		5
+#define CS35L35_AMP_GAIN_ZC_MASK	0x10
+#define CS35L35_AMP_GAIN_ZC_SHIFT	4
+
+#define CS35L35_AMP_DIGSFT_MASK		0x02
+#define CS35L35_AMP_DIGSFT_SHIFT	1
+
+/* CS35L35_SP_FMT_CTL3 */
+#define CS35L35_SP_I2S_DRV_MASK		0x03
+#define CS35L35_SP_I2S_DRV_SHIFT	0
+
+/* Class H Algorithm Control */
+#define CS35L35_CH_STEREO_MASK		0x40
+#define CS35L35_CH_STEREO_SHIFT		6
+#define CS35L35_CH_BST_OVR_MASK		0x04
+#define CS35L35_CH_BST_OVR_SHIFT	2
+#define CS35L35_CH_BST_LIM_MASK		0x08
+#define CS35L35_CH_BST_LIM_SHIFT	3
+#define CS35L35_CH_MEM_DEPTH_MASK	0x01
+#define CS35L35_CH_MEM_DEPTH_SHIFT	0
+#define CS35L35_CH_HDRM_CTL_MASK	0x3F
+#define CS35L35_CH_HDRM_CTL_SHIFT	0
+#define CS35L35_CH_REL_RATE_MASK	0xFF
+#define CS35L35_CH_REL_RATE_SHIFT	0
+#define CS35L35_CH_WKFET_DIS_MASK	0x80
+#define CS35L35_CH_WKFET_DIS_SHIFT	7
+#define CS35L35_CH_WKFET_DEL_MASK	0x70
+#define CS35L35_CH_WKFET_DEL_SHIFT	4
+#define CS35L35_CH_WKFET_THLD_MASK	0x0F
+#define CS35L35_CH_WKFET_THLD_SHIFT	0
+#define CS35L35_CH_VP_AUTO_MASK		0x80
+#define CS35L35_CH_VP_AUTO_SHIFT	7
+#define CS35L35_CH_VP_RATE_MASK		0x60
+#define CS35L35_CH_VP_RATE_SHIFT	5
+#define CS35L35_CH_VP_MAN_MASK		0x1F
+#define CS35L35_CH_VP_MAN_SHIFT		0
+
+/* CS35L35_PROT_RELEASE_CTL */
+#define CS35L35_CAL_ERR_RLS		0x80
+#define CS35L35_SHORT_RLS		0x04
+#define CS35L35_OTW_RLS			0x02
+#define CS35L35_OTE_RLS			0x01
+
+/* INT Mask Registers */
+#define CS35L35_INT1_CRIT_MASK		0x38
+#define CS35L35_INT2_CRIT_MASK		0xEF
+#define CS35L35_INT3_CRIT_MASK		0xEE
+#define CS35L35_INT4_CRIT_MASK		0xFF
+
+/* PDN DONE Masks */
+#define CS35L35_M_PDN_DONE_SHIFT	4
+#define CS35L35_M_PDN_DONE_MASK		0x10
+
+/* CS35L35_INT_1 */
+#define CS35L35_CAL_ERR			0x80
+#define CS35L35_OTP_ERR			0x40
+#define CS35L35_LRCLK_ERR		0x20
+#define CS35L35_SPCLK_ERR		0x10
+#define CS35L35_MCLK_ERR		0x08
+#define CS35L35_AMP_SHORT		0x04
+#define CS35L35_OTW			0x02
+#define CS35L35_OTE			0x01
+
+/* CS35L35_INT_2 */
+#define CS35L35_PDN_DONE		0x10
+#define CS35L35_VPBR_ERR		0x02
+#define CS35L35_VPBR_CLR		0x01
+
+/* CS35L35_INT_3 */
+#define CS35L35_BST_HIGH		0x10
+#define CS35L35_BST_HIGH_FLAG		0x08
+#define CS35L35_BST_IPK_FLAG		0x04
+#define CS35L35_LBST_SHORT		0x01
+
+/* CS35L35_INT_4 */
+#define CS35L35_VMON_OVFL		0x08
+#define CS35L35_IMON_OVFL		0x04
+
+#define CS35L35_FORMATS (SNDRV_PCM_FMTBIT_U8 | SNDRV_PCM_FMTBIT_S16_LE | \
+			SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE)
+
+struct  cs35l35_private {
+	struct device *dev;
+	struct cs35l35_platform_data pdata;
+	struct regmap *regmap;
+	struct regulator_bulk_data supplies[2];
+	int num_supplies;
+	int sysclk;
+	int sclk;
+	bool pdm_mode;
+	bool i2s_mode;
+	bool slave_mode;
+	/* GPIO for /RST */
+	struct gpio_desc *reset_gpio;
+	struct completion pdn_done;
+};
+
+static const char * const cs35l35_supplies[] = {
+	"VA",
+	"VP",
+};
+
+#endif

sound/soc/codecs/cs53l30.c

@@ -1130,6 +1130,7 @@ MODULE_DEVICE_TABLE(i2c, cs53l30_id);
 static struct i2c_driver cs53l30_i2c_driver = {
 	.driver = {
 		.name = "cs53l30",
+		.of_match_table = cs53l30_of_match,
 		.pm = &cs53l30_runtime_pm,
 	},
 	.id_table = cs53l30_id,

sound/soc/codecs/da7213.c

@@ -12,6 +12,7 @@
  * option) any later version.
  */
 
+#include <linux/acpi.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/i2c.h>
@@ -1528,12 +1529,23 @@ static int da7213_set_bias_level(struct snd_soc_codec *codec,
 	return 0;
 }
 
+#if defined(CONFIG_OF)
 /* DT */
 static const struct of_device_id da7213_of_match[] = {
 	{ .compatible = "dlg,da7213", },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, da7213_of_match);
+#endif
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id da7213_acpi_match[] = {
+	{ "DLGS7212", 0},
+	{ "DLGS7213", 0},
+	{ },
+};
+MODULE_DEVICE_TABLE(acpi, da7213_acpi_match);
+#endif
 
 static enum da7213_micbias_voltage
 	da7213_of_micbias_lvl(struct snd_soc_codec *codec, u32 val)
@@ -1844,6 +1856,7 @@ static struct i2c_driver da7213_i2c_driver = {
 	.driver = {
 		.name = "da7213",
 		.of_match_table = of_match_ptr(da7213_of_match),
+		.acpi_match_table = ACPI_PTR(da7213_acpi_match),
 	},
 	.probe		= da7213_i2c_probe,
 	.remove		= da7213_remove,

sound/soc/codecs/dio2125.c

@@ -0,0 +1,120 @@
+/*
+ * Copyright (c) 2017 BayLibre, SAS.
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ * The full GNU General Public License is included in this distribution
+ * in the file called COPYING.
+ */
+
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <sound/soc.h>
+
+#define DRV_NAME "dio2125"
+
+struct dio2125 {
+	struct gpio_desc *gpiod_enable;
+};
+
+static int drv_event(struct snd_soc_dapm_widget *w,
+		     struct snd_kcontrol *control, int event)
+{
+	struct snd_soc_component *c = snd_soc_dapm_to_component(w->dapm);
+	struct dio2125 *priv = snd_soc_component_get_drvdata(c);
+	int val;
+
+	switch (event) {
+	case SND_SOC_DAPM_POST_PMU:
+		val = 1;
+		break;
+	case SND_SOC_DAPM_PRE_PMD:
+		val = 0;
+		break;
+	default:
+		WARN(1, "Unexpected event");
+		return -EINVAL;
+	}
+
+	gpiod_set_value_cansleep(priv->gpiod_enable, val);
+
+	return 0;
+}
+
+static const struct snd_soc_dapm_widget dio2125_dapm_widgets[] = {
+	SND_SOC_DAPM_INPUT("INL"),
+	SND_SOC_DAPM_INPUT("INR"),
+	SND_SOC_DAPM_OUT_DRV_E("DRV", SND_SOC_NOPM, 0, 0, NULL, 0, drv_event,
+			       (SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD)),
+	SND_SOC_DAPM_OUTPUT("OUTL"),
+	SND_SOC_DAPM_OUTPUT("OUTR"),
+};
+
+static const struct snd_soc_dapm_route dio2125_dapm_routes[] = {
+	{ "DRV", NULL, "INL" },
+	{ "DRV", NULL, "INR" },
+	{ "OUTL", NULL, "DRV" },
+	{ "OUTR", NULL, "DRV" },
+};
+
+static const struct snd_soc_component_driver dio2125_component_driver = {
+	.dapm_widgets		= dio2125_dapm_widgets,
+	.num_dapm_widgets	= ARRAY_SIZE(dio2125_dapm_widgets),
+	.dapm_routes		= dio2125_dapm_routes,
+	.num_dapm_routes	= ARRAY_SIZE(dio2125_dapm_routes),
+};
+
+static int dio2125_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct dio2125 *priv;
+	int err;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (priv == NULL)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, priv);
+
+	priv->gpiod_enable = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW);
+	if (IS_ERR(priv->gpiod_enable)) {
+		err = PTR_ERR(priv->gpiod_enable);
+		if (err != -EPROBE_DEFER)
+			dev_err(dev, "Failed to get 'enable' gpio: %d", err);
+		return err;
+	}
+
+	return devm_snd_soc_register_component(dev, &dio2125_component_driver,
+					       NULL, 0);
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id dio2125_ids[] = {
+	{ .compatible = "dioo,dio2125", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, dio2125_ids);
+#endif
+
+static struct platform_driver dio2125_driver = {
+	.driver = {
+		.name = DRV_NAME,
+		.of_match_table = of_match_ptr(dio2125_ids),
+	},
+	.probe = dio2125_probe,
+};
+
+module_platform_driver(dio2125_driver);
+
+MODULE_DESCRIPTION("ASoC DIO2125 output driver");
+MODULE_AUTHOR("Jerome Brunet <jbrunet@baylibre.com>");
+MODULE_LICENSE("GPL");

sound/soc/dwc/Kconfig

@@ -8,10 +8,10 @@ config SND_DESIGNWARE_I2S
 	 maximum of 8 channels each for play and record.
 
 config SND_DESIGNWARE_PCM
-	tristate "PCM PIO extension for I2S driver"
+	bool "PCM PIO extension for I2S driver"
 	depends on SND_DESIGNWARE_I2S
 	help
-	 Say Y, M or N if you want to add a custom ALSA extension that registers
+	 Say Y or N if you want to add a custom ALSA extension that registers
 	 a PCM and uses PIO to transfer data.
 
 	 This functionality is specially suited for I2S devices that don't have

sound/soc/dwc/Makefile

@@ -1,5 +1,5 @@
 # SYNOPSYS Platform Support
 obj-$(CONFIG_SND_DESIGNWARE_I2S) += designware_i2s.o
-ifdef CONFIG_SND_DESIGNWARE_PCM
+
-obj-$(CONFIG_SND_DESIGNWARE_I2S) += designware_pcm.o
+designware_i2s-y := dwc-i2s.o
-endif
+designware_i2s-$(CONFIG_SND_DESIGNWARE_PCM) += dwc-pcm.o

sound/soc/dwc/dwc-pcm.c

@@ -129,13 +129,11 @@ void dw_pcm_push_tx(struct dw_i2s_dev *dev)
 {
 	dw_pcm_transfer(dev, true);
 }
-EXPORT_SYMBOL_GPL(dw_pcm_push_tx);
 
 void dw_pcm_pop_rx(struct dw_i2s_dev *dev)
 {
 	dw_pcm_transfer(dev, false);
 }
-EXPORT_SYMBOL_GPL(dw_pcm_pop_rx);
 
 static int dw_pcm_open(struct snd_pcm_substream *substream)
 {
@@ -281,4 +279,3 @@ int dw_pcm_register(struct platform_device *pdev)
 {
 	return devm_snd_soc_register_platform(&pdev->dev, &dw_pcm_platform);
 }
-EXPORT_SYMBOL_GPL(dw_pcm_register);