Merge branch 'Add-comphy-support-for-Armada-38x'

Russell King says:

====================
Add comphy support for Armada 38x

This series adds support for the comphy for Armada 38x, which allows
these SoCs to use 2500BASE-X mode with appropriate SFP modules.

Tested on SolidRun Clearfog after updating for the 5.0 merge window
changes.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt

@@ -19,7 +19,7 @@ Optional properties:
   "marvell,armada-370-neta" and 9800B for others.
 - clock-names: List of names corresponding to clocks property; shall be
   "core" for core clock and "bus" for the optional bus clock.
-
+- phys: comphy for the ethernet port, see ../phy/phy-bindings.txt
 
 Optional properties (valid only for Armada XP/38x):
 

Documentation/devicetree/bindings/phy/phy-armada38x-comphy.txt

@@ -0,0 +1,40 @@
+mvebu armada 38x comphy driver
+------------------------------
+
+This comphy controller can be found on Marvell Armada 38x. It provides a
+number of shared PHYs used by various interfaces (network, sata, usb,
+PCIe...).
+
+Required properties:
+
+- compatible: should be "marvell,armada-380-comphy"
+- reg: should contain the comphy register location and length.
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+
+A sub-node is required for each comphy lane provided by the comphy.
+
+Required properties (child nodes):
+
+- reg: comphy lane number.
+- #phy-cells : from the generic phy bindings, must be 1. Defines the
+               input port to use for a given comphy lane.
+
+Example:
+
+	comphy: phy@18300 {
+		compatible = "marvell,armada-380-comphy";
+		reg = <0x18300 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpm_comphy0: phy@0 {
+			reg = <0>;
+			#phy-cells = <1>;
+		};
+
+		cpm_comphy1: phy@1 {
+			reg = <1>;
+			#phy-cells = <1>;
+		};
+	};

arch/arm/boot/dts/armada-388-clearfog.dtsi

@@ -93,6 +93,7 @@ &eth1 {
 	bm,pool-long = <2>;
 	bm,pool-short = <1>;
 	buffer-manager = <&bm>;
+	phys = <&comphy1 1>;
 	phy-mode = "sgmii";
 	status = "okay";
 };
@@ -103,6 +104,7 @@ &eth2 {
 	bm,pool-short = <1>;
 	buffer-manager = <&bm>;
 	managed = "in-band-status";
+	phys = <&comphy5 2>;
 	phy-mode = "sgmii";
 	sfp = <&sfp>;
 	status = "okay";

arch/arm/boot/dts/armada-38x.dtsi

@@ -335,6 +335,43 @@ gateclk: clock-gating-control@18220 {
 				#clock-cells = <1>;
 			};
 
+			comphy: phy@18300 {
+				compatible = "marvell,armada-380-comphy";
+				reg = <0x18300 0x100>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				comphy0: phy@0 {
+					reg = <0>;
+					#phy-cells = <1>;
+				};
+
+				comphy1: phy@1 {
+					reg = <1>;
+					#phy-cells = <1>;
+				};
+
+				comphy2: phy@2 {
+					reg = <2>;
+					#phy-cells = <1>;
+				};
+
+				comphy3: phy@3 {
+					reg = <3>;
+					#phy-cells = <1>;
+				};
+
+				comphy4: phy@4 {
+					reg = <4>;
+					#phy-cells = <1>;
+				};
+
+				comphy5: phy@5 {
+					reg = <5>;
+					#phy-cells = <1>;
+				};
+			};
+
 			coreclk: mvebu-sar@18600 {
 				compatible = "marvell,armada-380-core-clock";
 				reg = <0x18600 0x04>;

drivers/net/ethernet/marvell/mvneta.c

@@ -27,6 +27,7 @@
 #include <linux/of_irq.h>
 #include <linux/of_mdio.h>
 #include <linux/of_net.h>
+#include <linux/phy/phy.h>
 #include <linux/phy.h>
 #include <linux/phylink.h>
 #include <linux/platform_device.h>
@@ -436,6 +437,7 @@ struct mvneta_port {
 	struct device_node *dn;
 	unsigned int tx_csum_limit;
 	struct phylink *phylink;
+	struct phy *comphy;
 
 	struct mvneta_bm *bm_priv;
 	struct mvneta_bm_pool *pool_long;
@@ -3151,6 +3153,8 @@ static void mvneta_start_dev(struct mvneta_port *pp)
 {
 	int cpu;
 
+	WARN_ON(phy_power_on(pp->comphy));
+
 	mvneta_max_rx_size_set(pp, pp->pkt_size);
 	mvneta_txq_max_tx_size_set(pp, pp->pkt_size);
 
@@ -3213,6 +3217,8 @@ static void mvneta_stop_dev(struct mvneta_port *pp)
 
 	mvneta_tx_reset(pp);
 	mvneta_rx_reset(pp);
+
+	WARN_ON(phy_power_off(pp->comphy));
 }
 
 static void mvneta_percpu_enable(void *arg)
@@ -3338,6 +3344,7 @@ static int mvneta_set_mac_addr(struct net_device *dev, void *addr)
 static void mvneta_validate(struct net_device *ndev, unsigned long *supported,
 			    struct phylink_link_state *state)
 {
+	struct mvneta_port *pp = netdev_priv(ndev);
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
 
 	/* We only support QSGMII, SGMII, 802.3z and RGMII modes */
@@ -3358,8 +3365,13 @@ static void mvneta_validate(struct net_device *ndev, unsigned long *supported,
 	phylink_set(mask, Pause);
 
 	/* Half-duplex at speeds higher than 100Mbit is unsupported */
-	phylink_set(mask, 1000baseT_Full);
+	if (pp->comphy || state->interface != PHY_INTERFACE_MODE_2500BASEX) {
-	phylink_set(mask, 1000baseX_Full);
+		phylink_set(mask, 1000baseT_Full);
+		phylink_set(mask, 1000baseX_Full);
+	}
+	if (pp->comphy || state->interface == PHY_INTERFACE_MODE_2500BASEX) {
+		phylink_set(mask, 2500baseX_Full);
+	}
 
 	if (!phy_interface_mode_is_8023z(state->interface)) {
 		/* 10M and 100M are only supported in non-802.3z mode */
@@ -3373,6 +3385,11 @@ static void mvneta_validate(struct net_device *ndev, unsigned long *supported,
 		   __ETHTOOL_LINK_MODE_MASK_NBITS);
 	bitmap_and(state->advertising, state->advertising, mask,
 		   __ETHTOOL_LINK_MODE_MASK_NBITS);
+
+	/* We can only operate at 2500BaseX or 1000BaseX.  If requested
+	 * to advertise both, only report advertising at 2500BaseX.
+	 */
+	phylink_helper_basex_speed(state);
 }
 
 static int mvneta_mac_link_state(struct net_device *ndev,
@@ -3384,7 +3401,9 @@ static int mvneta_mac_link_state(struct net_device *ndev,
 	gmac_stat = mvreg_read(pp, MVNETA_GMAC_STATUS);
 
 	if (gmac_stat & MVNETA_GMAC_SPEED_1000)
-		state->speed = SPEED_1000;
+		state->speed =
+			state->interface == PHY_INTERFACE_MODE_2500BASEX ?
+			SPEED_2500 : SPEED_1000;
 	else if (gmac_stat & MVNETA_GMAC_SPEED_100)
 		state->speed = SPEED_100;
 	else
@@ -3499,12 +3518,20 @@ static void mvneta_mac_config(struct net_device *ndev, unsigned int mode,
 			    MVNETA_GMAC_FORCE_LINK_DOWN);
 	}
 
+
 	/* When at 2.5G, the link partner can send frames with shortened
 	 * preambles.
 	 */
 	if (state->speed == SPEED_2500)
 		new_ctrl4 |= MVNETA_GMAC4_SHORT_PREAMBLE_ENABLE;
 
+	if (pp->comphy &&
+	    (state->interface == PHY_INTERFACE_MODE_SGMII ||
+	     state->interface == PHY_INTERFACE_MODE_1000BASEX ||
+	     state->interface == PHY_INTERFACE_MODE_2500BASEX))
+		WARN_ON(phy_set_mode_ext(pp->comphy, PHY_MODE_ETHERNET,
+					 state->interface));
+
 	if (new_ctrl0 != gmac_ctrl0)
 		mvreg_write(pp, MVNETA_GMAC_CTRL_0, new_ctrl0);
 	if (new_ctrl2 != gmac_ctrl2)
@@ -4404,7 +4431,7 @@ static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
 	if (phy_mode == PHY_INTERFACE_MODE_QSGMII)
 		mvreg_write(pp, MVNETA_SERDES_CFG, MVNETA_QSGMII_SERDES_PROTO);
 	else if (phy_mode == PHY_INTERFACE_MODE_SGMII ||
-		 phy_mode == PHY_INTERFACE_MODE_1000BASEX)
+		 phy_interface_mode_is_8023z(phy_mode))
 		mvreg_write(pp, MVNETA_SERDES_CFG, MVNETA_SGMII_SERDES_PROTO);
 	else if (!phy_interface_mode_is_rgmii(phy_mode))
 		return -EINVAL;
@@ -4421,6 +4448,7 @@ static int mvneta_probe(struct platform_device *pdev)
 	struct mvneta_port *pp;
 	struct net_device *dev;
 	struct phylink *phylink;
+	struct phy *comphy;
 	const char *dt_mac_addr;
 	char hw_mac_addr[ETH_ALEN];
 	const char *mac_from;
@@ -4446,6 +4474,14 @@ static int mvneta_probe(struct platform_device *pdev)
 		goto err_free_irq;
 	}
 
+	comphy = devm_of_phy_get(&pdev->dev, dn, NULL);
+	if (comphy == ERR_PTR(-EPROBE_DEFER)) {
+		err = -EPROBE_DEFER;
+		goto err_free_irq;
+	} else if (IS_ERR(comphy)) {
+		comphy = NULL;
+	}
+
 	phylink = phylink_create(dev, pdev->dev.fwnode, phy_mode,
 				 &mvneta_phylink_ops);
 	if (IS_ERR(phylink)) {
@@ -4462,6 +4498,7 @@ static int mvneta_probe(struct platform_device *pdev)
 	pp = netdev_priv(dev);
 	spin_lock_init(&pp->lock);
 	pp->phylink = phylink;
+	pp->comphy = comphy;
 	pp->phy_interface = phy_mode;
 	pp->dn = dn;
 

drivers/phy/marvell/Kconfig

@@ -21,6 +21,16 @@ config PHY_BERLIN_USB
 	help
 	  Enable this to support the USB PHY on Marvell Berlin SoCs.
 
+config PHY_MVEBU_A38X_COMPHY
+	tristate "Marvell Armada 38x comphy driver"
+	depends on ARCH_MVEBU || COMPILE_TEST
+	depends on OF
+	select GENERIC_PHY
+	help
+	  This driver allows to control the comphy, an hardware block providing
+	  shared serdes PHYs on Marvell Armada 38x. Its serdes lanes can be
+	  used by various controllers (Ethernet, sata, usb, PCIe...).
+
 config PHY_MVEBU_CP110_COMPHY
 	tristate "Marvell CP110 comphy driver"
 	depends on ARCH_MVEBU || COMPILE_TEST

drivers/phy/marvell/Makefile

@@ -2,6 +2,7 @@
 obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
 obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
 obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
+obj-$(CONFIG_PHY_MVEBU_A38X_COMPHY)	+= phy-armada38x-comphy.o
 obj-$(CONFIG_PHY_MVEBU_CP110_COMPHY)	+= phy-mvebu-cp110-comphy.o
 obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
 obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o

drivers/phy/marvell/phy-armada38x-comphy.c

@@ -0,0 +1,237 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Russell King, Deep Blue Solutions Ltd.
+ *
+ * Partly derived from CP110 comphy driver by Antoine Tenart
+ * <antoine.tenart@bootlin.com>
+ */
+#include <linux/delay.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+
+#define MAX_A38X_COMPHY	6
+#define MAX_A38X_PORTS	3
+
+#define COMPHY_CFG1		0x00
+#define  COMPHY_CFG1_GEN_TX(x)		((x) << 26)
+#define  COMPHY_CFG1_GEN_TX_MSK		COMPHY_CFG1_GEN_TX(15)
+#define  COMPHY_CFG1_GEN_RX(x)		((x) << 22)
+#define  COMPHY_CFG1_GEN_RX_MSK		COMPHY_CFG1_GEN_RX(15)
+#define  GEN_SGMII_1_25GBPS		6
+#define  GEN_SGMII_3_125GBPS		8
+
+#define COMPHY_STAT1		0x18
+#define  COMPHY_STAT1_PLL_RDY_TX	BIT(3)
+#define  COMPHY_STAT1_PLL_RDY_RX	BIT(2)
+
+#define COMPHY_SELECTOR		0xfc
+
+struct a38x_comphy;
+
+struct a38x_comphy_lane {
+	void __iomem *base;
+	struct a38x_comphy *priv;
+	unsigned int n;
+
+	int port;
+};
+
+struct a38x_comphy {
+	void __iomem *base;
+	struct device *dev;
+	struct a38x_comphy_lane lane[MAX_A38X_COMPHY];
+};
+
+static const u8 gbe_mux[MAX_A38X_COMPHY][MAX_A38X_PORTS] = {
+	{ 0, 0, 0 },
+	{ 4, 5, 0 },
+	{ 0, 4, 0 },
+	{ 0, 0, 4 },
+	{ 0, 3, 0 },
+	{ 0, 0, 3 },
+};
+
+static void a38x_comphy_set_reg(struct a38x_comphy_lane *lane,
+				unsigned int offset, u32 mask, u32 value)
+{
+	u32 val;
+
+	val = readl_relaxed(lane->base + offset) & ~mask;
+	writel(val | value, lane->base + offset);
+}
+
+static void a38x_comphy_set_speed(struct a38x_comphy_lane *lane,
+				  unsigned int gen_tx, unsigned int gen_rx)
+{
+	a38x_comphy_set_reg(lane, COMPHY_CFG1,
+			    COMPHY_CFG1_GEN_TX_MSK | COMPHY_CFG1_GEN_RX_MSK,
+			    COMPHY_CFG1_GEN_TX(gen_tx) |
+		            COMPHY_CFG1_GEN_RX(gen_rx));
+}
+
+static int a38x_comphy_poll(struct a38x_comphy_lane *lane,
+			    unsigned int offset, u32 mask, u32 value)
+{
+	u32 val;
+	int ret;
+
+	ret = readl_relaxed_poll_timeout_atomic(lane->base + offset, val,
+						(val & mask) == value,
+						1000, 150000);
+
+	if (ret)
+		dev_err(lane->priv->dev,
+			"comphy%u: timed out waiting for status\n", lane->n);
+
+	return ret;
+}
+
+/*
+ * We only support changing the speed for comphys configured for GBE.
+ * Since that is all we do, we only poll for PLL ready status.
+ */
+static int a38x_comphy_set_mode(struct phy *phy, enum phy_mode mode, int sub)
+{
+	struct a38x_comphy_lane *lane = phy_get_drvdata(phy);
+	unsigned int gen;
+
+	if (mode != PHY_MODE_ETHERNET)
+		return -EINVAL;
+
+	switch (sub) {
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_1000BASEX:
+		gen = GEN_SGMII_1_25GBPS;
+		break;
+
+	case PHY_INTERFACE_MODE_2500BASEX:
+		gen = GEN_SGMII_3_125GBPS;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	a38x_comphy_set_speed(lane, gen, gen);
+
+	return a38x_comphy_poll(lane, COMPHY_STAT1,
+				COMPHY_STAT1_PLL_RDY_TX |
+				COMPHY_STAT1_PLL_RDY_RX,
+				COMPHY_STAT1_PLL_RDY_TX |
+				COMPHY_STAT1_PLL_RDY_RX);
+}
+
+static const struct phy_ops a38x_comphy_ops = {
+	.set_mode	= a38x_comphy_set_mode,
+	.owner		= THIS_MODULE,
+};
+
+static struct phy *a38x_comphy_xlate(struct device *dev,
+				     struct of_phandle_args *args)
+{
+	struct a38x_comphy_lane *lane;
+	struct phy *phy;
+	u32 val;
+
+	if (WARN_ON(args->args[0] >= MAX_A38X_PORTS))
+		return ERR_PTR(-EINVAL);
+
+	phy = of_phy_simple_xlate(dev, args);
+	if (IS_ERR(phy))
+		return phy;
+
+	lane = phy_get_drvdata(phy);
+	if (lane->port >= 0)
+		return ERR_PTR(-EBUSY);
+
+	lane->port = args->args[0];
+
+	val = readl_relaxed(lane->priv->base + COMPHY_SELECTOR);
+	val = (val >> (4 * lane->n)) & 0xf;
+
+	if (!gbe_mux[lane->n][lane->port] ||
+	    val != gbe_mux[lane->n][lane->port]) {
+		dev_warn(lane->priv->dev,
+			 "comphy%u: not configured for GBE\n", lane->n);
+		phy = ERR_PTR(-EINVAL);
+	}
+
+	return phy;
+}
+
+static int a38x_comphy_probe(struct platform_device *pdev)
+{
+	struct phy_provider *provider;
+	struct device_node *child;
+	struct a38x_comphy *priv;
+	struct resource *res;
+	void __iomem *base;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	priv->dev = &pdev->dev;
+	priv->base = base;
+
+	for_each_available_child_of_node(pdev->dev.of_node, child) {
+		struct phy *phy;
+		int ret;
+		u32 val;
+
+		ret = of_property_read_u32(child, "reg", &val);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "missing 'reg' property (%d)\n",
+				ret);
+			continue;
+		}
+
+		if (val >= MAX_A38X_COMPHY || priv->lane[val].base) {
+			dev_err(&pdev->dev, "invalid 'reg' property\n");
+			continue;
+		}
+
+		phy = devm_phy_create(&pdev->dev, child, &a38x_comphy_ops);
+		if (IS_ERR(phy))
+			return PTR_ERR(phy);
+
+		priv->lane[val].base = base + 0x28 * val;
+		priv->lane[val].priv = priv;
+		priv->lane[val].n = val;
+		priv->lane[val].port = -1;
+		phy_set_drvdata(phy, &priv->lane[val]);
+	}
+
+	dev_set_drvdata(&pdev->dev, priv);
+
+	provider = devm_of_phy_provider_register(&pdev->dev, a38x_comphy_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id a38x_comphy_of_match_table[] = {
+	{ .compatible = "marvell,armada-380-comphy" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, a38x_comphy_of_match_table);
+
+static struct platform_driver a38x_comphy_driver = {
+	.probe	= a38x_comphy_probe,
+	.driver	= {
+		.name = "armada-38x-comphy",
+		.of_match_table = a38x_comphy_of_match_table,
+	},
+};
+module_platform_driver(a38x_comphy_driver);
+
+MODULE_AUTHOR("Russell King <rmk+kernel@armlinux.org.uk>");
+MODULE_DESCRIPTION("Common PHY driver for Armada 38x SoCs");
+MODULE_LICENSE("GPL v2");